Search Documents

By A B. Richards

Time window analysis that limits the explosive mass fired within a specified time window (commonly eight milliseconds) has been used for many years in blast design by explosives engineers. Despite several warnings in the past that this technique has limited practical or scientific basis and, in many cases, does not effectively control vibration, almost every textbook and blasting manual refers to time window charge mass limits as a primary vibration control technique. It has become entrenched in some blast vibration management plans, despite being inappropriate for the particular situation. With the flexible initiation timing available with electronic detonation almost a practical reality, and the 8 ms constraints in-built into the signal tube initiation system thereby lifted, it is timely to review the significance of the 8 ms time window in controlling blast vibration. This paper re-visits the original research that led to the development of the 8 ms criteria and the non-supportive conclusion of the original researcher. Because airblast was not measured, the 8 ms time window was never intended to be applicable for airblast control. Examples of blast designs are given in this paper that comply with the 8 ms time window limit that result in substantially increased air and ground vibration, together with examples of blast design that does not satisfy time window considerations, which results in reduced air and ground vibration. Techniques that identify wavefront reinforcement, due to the combined effect of drilling pattern and delay sequence, can assist explosives engineers to avoid high blast vibration situations that result from the inappropriate application of time window techniques and other adverse delay combinations.

Jan 1, 2003

Since the mid-1970s there has been increasing attention in the South Pacific area to the problems of disaster planning and management at various levels, mainly from regional through national to provincial levels. This concern has been expressed in a variety of ways. International aid donors have made their views known in commentaries or reports. Seminar discussions have been organised at the regional level (such as at Suva, 1976; Suva, 1979; Tonga, 1982 and Suva, 1983). In-country training workshops or meetings have been organised (such as the "Disaster Preparedness Workshops for Non-governmental Organisations" in Pacific countries, jointly run by the Australian Red Cross and the Australian Overseas Disaster Response Organisation and supported by AIDAB, in Vanuatu, 1985; Solomon Islands, 1985; Western Samoa, 1986; Fiji, 1987; Tonga, 1987; Lae and Port Moresby, Papua New Guinea, 1988) or held outside the area (ACDC at Macedon, 1981). Training and/or research institutions have been established such as the East-West Center, Honolulu, and the Asian Disaster Preparedness Center, Bangkok (more Asia oriented). As part of the East-West Center Pacific Islands Development Program's Disaster Preparedness Project, a detailed manual of disaster preparedness and response procedures and guidelines has been published (Carter, 1984).Table 1 and figure 1 show that the area with which this discussion deals is a highly fragmented island region, comprising many small, some minute, nations, both in land area and population. The social structure is predominantly rural, with the capital city often making up a small part of the total population and, in absolute terms, little more than a small town. Outside the administrative and governmental activities concentrated in the capitals, in most cases the indigenous inhabitants depend on subsistence agriculture or on usually a monocultural concentration on a cash crop, most frequently coconuts.

Jan 1, 1990

By Qi P. H

Gold dissolution can be achieved with a number of complexing ligands, all with varying degrees of stability. Processes based on the use of halogens have been known for many years. Beside providing the necessary complex- ing role, the halogens under the appropriate conditions are very effective oxidants for gold. Of the halogens, the gold iodide complexes are the most stable in aqueous solution. Iodine can establish the desired oxidation poten- tial for oxidizing gold, and unlike chlorine and bromine, the oxidizing potential of iodine is mild enough to avoid the oxidation of impurity constituents like metal sulfides. A series of experiments to investigate the fundamental electrochemistry of gold in different halide solutions was performed. Cyclic voltammograms of gold in the presence of 10-2 M chloride, bromide and iodide, respectively show that for a given potential the rate of oxidation is much faster in iodide solution than in either chloride or bromide. An overlay of linear sweep voltammograms for the anodic oxidation of gold in iodide and the cathodic reduction of iodine species on gold provides an effective method for examining the dissolution of gold in iodideftodine solution. The dissolution rates obtained from both electrochemical and actual leaching results are compared. Optimum leaching conditions are analyzed in terms of the iodide/iodine concentrations. Conceptual processes for the recovery of gold and iodide and the regeneration of iodine are discussed.

Jan 1, 1991

Expansion of the B.H.P. Co. Ltd. mater ials handling facilities, at their Newcastle Steelworks, began in 1964 and continued until 1970. The present complex handles the annual iron ore requirement of some three million tons for the Sinter Plant and Blast Furnaces. Iron ore is discharged from ore carriers and conveyed at rates up to 3,000 t.p.h. to either of two 180,000 ton capacity storage yards, where it is blended using boom stackers. Material is reclaimed from these yards at rates up to 1,000 t.p.h. using a slewing boom bucket-wheel reclaimer and fed to a screening station. Oversize material is scalped out and crushed in a closed circuit cone crusher. Undersize material is sized on double-deck vibratory screens which separate at 1/4in (6mm). The two fractions are blended in two of four 70,000 ton capacity blending yards using slewing boom travelling stackers. Bridge-mounted bucket-wheel reclaimers reclaim the blended piles at 1,000 t.p.h. Fine ore is conveyed to the Sinter Plant and lump ore to a second screening station, for rescreening, before passing to the Blast Furnace.

Jan 1, 1972

Coal Mining Land Use on the southern coalfields often preceded other land uses. Over the past century overlying land use has altered significantly, particularly with water supply storage development, road system building, railways, pipelines, electricity reticulation schemes and general urban develop- ment. National Parks were declared over coal bearing lands. Little regard was paid to the coal under the land surface by land developers, Government instrumentalities, central planners and the Metropolitan Water, Sewerage and Drainage Board and others, and little value was placed on this valuable energy source. These bodies derived no benefit from the under- lying mineral. In these circumstances, mine operators and such surface land users were put into adversary roles. Mass sterilisation of coal resources resulted. The loss of reserves continues, although the problem has become better under- stood. An Energy Impact Statement (EIS) submission by all surface land developers has been proposed as a means to justify the impact of the development on the coal reserves Beneath.

Jan 1, 1979

The Cadjebut Mine is located 80 km southeast of Fitzroy Crossing. Cadjebut is owned 58 per cent by BHP Minerals and 42 per cent by Billiton Australia. Cadjebut is a 'Mississippi Valley Type' (MVT) deposit. Minerals present are sphalerite, galena and marcasite in a sedimentary host of dolomite and siltstone. The ore contains few deleterious impurities and no silver. The mill was commissioned in the first half of 1988 at a rate of 320 000 tonnes per annum. An expansion in the latter half of 1989 has since increased production to 550 000 tonnes per annum. The initial geological resource at the commencement of mining was 3.8 million tonnes at 13.5 per cent Zn and 4.4 per cent Pb. There is sufficient ore left to sustain operations to 1995 at a grade of 11.2 per cent Zn and 3.9 per cent Pb. The ore from underground is stockpiled on the surface via a drift conveyor and from the stockpile is fed into a grinding circuit consisting of a SAG and ball mill. Cyclone overflow at a Pgp of 90 pm gravitates to the flotation circuit. Lead and zinc are sequentially floated to produce an 80 per cent Pb grade at 90 per cent recovery and a 61 - 62 per cent Zn grade at 96 per cent recovery. The concentrates are thickened and filtered before being trucked to the port of Wyndham 600 km away. From Wyndham the concentrates are shipped to smelters in Asia, Europe and Australia.

Jan 1, 1992

By Payne AR

The high cost of gateroad repairs and maintenance in U.K. longwall coalmining is a clear indication of the failure of permanent support systems to fulfill their prime function, i.e. control of strata movement. The main component of gateroad support is the pack, the design and materials of which have experienced an important development process during the last 10-15 years. More recently, research investigators have attempted to give a design basis to pack quality and dimension, and reference is made to two theoretical approaches. In the course of a current research programme based upon in situ monitoring, interim design recommendations have been proposed as a means of effecting improvement in support efficiency. Identification of characteristic deformation behaviour forms the basis of the recommendations made and the subsequent improvement in gateroad performance reported.

Jan 1, 1986

By Torckler L, Brathwaite R. L

At Neavesville gold-silver (electrum) mineralization occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydro- thermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz- adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy ana sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt. % NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei aria riroaolan¦s. The age of the rhyolitic pyroclastics and related alteration and mineralization is probably Pliocene and Neavesville therefore represents a fossil geothermal system.

Jan 1, 1980

The interaction of man with the environment has a double character. From one side, mankind can not exist without co- nsuming the natural resources and, from the other side, we actively alter and exert influence upon nature. Analysis reveals that the ecological problem is, to a great extent, a geological one. The paper deals with the application of grouting techniques to construct impermeable barriers for the protection of ground water and soils from depletion and industrial wastes pollution. A number of case histories in the field of mine construction is given to illustrate the solution of geotechnical problems in concert with environ- mental protection measures.

Jan 1, 1988

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

In November, 1967, a four strand curved mould continuous casting machine coupled with a 50 ton basic oxygen furnace began producing billets for the rod mill and new merchant mill at the Newcastle Steelworks. To date over 500,000 tons of carbon and alloy steels have been cast at the rate of 20,000 tons per month, the major part for the wire industry. Many alterations have been made to the plant to simplify the process, improve quality and increase production. Casting parameters have been developed for each different type of steel. The quality of the final product has been influenced most by casting temperature, secondary cooling and casting speed. All these factors have been controlled and good results are reproduced. More exacting requirements of liquid steel quality have brought about the use of higher lime/silica ratio slags during steelmaking to control phosphorus revers- ions and standard ladle additions of manganese suicide and ferro aluminium for more effective deoxidation.

Jan 1, 1972

By Morris P. H

A trial embankment was constructed using coarse coal mine reject on a deposit of crusted coal mine tailings at New Hope Colliery, located in the Bundamba District of the West Moreton Coalfields in South East Queensland, Australia. The purpose of the trial embankment was to assess the load carrying capacity and settlement behaviour of the crusted tailings, including an assessment of strength gain in the tailings under the influence of the fill. Prior to construction of the trial embankment, a site investigation of the tailings deposit was carried out. This comprised vane shear strength testing, together with disturbed sampling and undisturbed block sampling for the purposes of laboratory testing. Following the site investigation, settlement plates and standpipes were installed at various depths and locations within the tailings in the vicinity of the proposed embankment. The instrumentation enabled the magnitudes and distributions of settlement and pore pressure within the tailings to be determined during and following construction of the embankment. The embankment was constructed using coarse reject in three equal lifts to a height of 3.0 m. The tailings sustained a maximum settlement under the weight of the fill of 290 mm, representing about 4.2 ii of the average initial thickness of the tailings and a loss of embankment height of about 9.7 %. By the end of the monitoring period the strength of the softer tailings underlying therust had roughly doubled under the influence of tha cmbarikment

Jan 1, 1990

By M J M Cunningham, M Greentree, J H Liu

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Palaeozoic rocks of north-eastern Laos are an attractive target for gold explorers due to the complex tectonic history and lack of past exploration in the region. Alluvial workings along the Nam Xiang River and its tributaries have highlighted the potential for gold mineralisation in the Vieng Kham region. The Nam Xiang River follows a regionally-extensive NNE-striking thrust fault. Adjacent to the Nam Xiang fault, the dip of the main foliation steepens, and in many places the stratigraphy is overturned as a result of this faulting.United Minerals and Mining Company conducted a regional exploration program to explore for gold. This included stream sediment and rock-chip sampling, and airborne geophysics. Geochemical anomalies were followed up with more detailed exploration, including geological mapping and soil sampling. Despite the relatively deep weathering profile, gold mineralisation is associated with a low-level but well-defined gold-in-soil anomaly. Drilling has shown that gold mineralisation occurs on structures and fabrics parallel to the main Nam Xiang fault. The highest gold grades are associated with brecciated sandstones that have experienced strong carbonate alteration. This suggests that late-stage structures such as the Nam Xiang fault are the major control on gold mineralisation in the region.CITATION:Greentree, M, Cunningham, M J M and Liu, J H, 2015. Gold mineralisation along the Nam Xiang fault, Vieng Kham Project, North-east Laos, in Proceedings PACRIM 2015 Congress, pp 177–182 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Cataclysmic or flood-like release of gas-charged brines, hydrocarbons and slurries accompanied widespread mineralisation of Upper Devonian environments. These are well represented in the Canning and Burdekin Basins of Western Australia and Queensland respectively.The Burdekin Basin provides particularly instructive vein structural sequences. These fall into organic residue to carbonate paragenetic sequences which are known elsewhere to record progressive decarboxylation. Fibrous veins indicate overpressure in fractures with organic residues, acids and gas derivatives driven to overlying groundwater flows. This combination of large flow rates and potent organic mineralisers led to extensive arsenical rare-metal mineralisation which is similar to that concentrated in Upper Devonian extinction horizons of the Canning Basin. Organic-residue mineralisation appears concentrated by certain hvdrostructures and targeted upon particular species. These controls need to be understood to guide modern management stragegies for mineralised organic and nitrogenous wastes.

Jan 1, 1990

By Ishijima Y, Goto T

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic ar- ray. Location of microseismic events and in- tensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the inten- sity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increas- ing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are con- sidered. Observed and predicted displacement of the shaft axis agreed well.

Jan 1, 1992

By Jorgensen FRA, Moyle FJ, Turner TM

Laminar flow furnace techniques and thermal analysis were used to study the combustion of Kambalda nickel concentrate and Collie coal. The study was made to ascertain the suitability of the latter as a replacement for the fuel oil currently burnt in a flash furnace at the Kal- goorlie Nickel Smelter. The coal was found to ignite at temperatures between 500-600¦C which was the same as that required for the most reac- tive component of the concentrate, namely py- rite. The rates of reaction of both the coal and concentrate were dependent on oxygen con- centration. Sulfur dioxide hindered the combus- tion of concentrate and of coal, the effect on the concentrate being the more pronounced. The effects of moisture content and the tendency for spontaneous combustion of the coal were also noted.

Jan 1, 1982

A major tool in the search for petroleum is reflection seismic mapping. The period which has seen most of the exploration in Victoria is also one which has seen major advances in this technology, from 1963 try present day. Seismic mapping can be divided into three interlinked areas - acquisition, processing, and interpretation. In acquisition the major changes have been from an explosive energy source in 1963 to gas exploders in 1968 and airguns in 1970. The number of recording channels has increased from 24 to 192, with digital recording introduced in 1966, and floating point recording in 1976.

Jan 1, 1982

Introduction The mine winder is an essential element in the mining of ore in deep level mines and therefore requires a high degree of reliability to avoid interruption of production. Failure of any component on a winder may also be dangerous and expensive to repair. The larger the failure the larger the stoppage. The failure of a winder drum is the ultimate catastrophe, not only because of the cost of replacement, but also because of the lead time in procuring a new drum. Today these types of failure are not as common but many failures have occurred in the past and even today many an old winder is con- sidered for a new and often more arduous duty. As far back as the turn of the century a lot of information had been gathered to try and clear up the complexities of the multi- layering effect of coiling rope under tension onto a drum. Before comparing results obtained by various researchers the nature of the pressure distribution between rope and drum due to multi-layering will be discussed briefly.

Jan 1, 1987

In-situ leaching of gold deposits has not become an option largely as a result the lack of suitability of cyanide as a lixiviant due to sluggish kinetics and high dependence on the availability of oxygen. A second problem area is the excessive cost of drilling the required number of injection and production wells needed to service a wellfield capable of maintaining any significant throughput or providing and acceptable level of gold production. Well spacing in in-situ leaching operations is limited by solution life, dissolution rate, and the need for solution control. With cyanide the life of an active solution capable of dissolving significant gold is severely limited by the availability of oxygen which cannot be readily replaced while the solution remains underground. The extremely slow gold dissolution rate also necessitates excessive contact periods in order to dissolve coarse gold.

Jan 1, 1991

By Warren L. J

In the mineral processing industry solid-liquid separation within a thickener usually requires the addition of a synthetic flocculant to enhance the settling rate of fine particles. The characteristics of the resulting flocculated suspensions may vary considerably depending upon the physical and chemical conditions which prevail during the flocculation process. For example, parameters such as flocculant type, dosage and solution concentration, surface chemical characteristics of particles and the suspension agitation conditions can influence the degree to which the particles aggregate. Aggregated suspensions exhibit various structures, and range from those composed of small, dense aggregates to those containing large, voluminous aggregates. The size distribution and structural type of the aggregates which form within the feed-well of a thickener can have a dramatic effect upon overall thickener performance. Thickener performance cannot be optimized without optimization of the aggregate structure produced in the feed by synthetic flocculant addition. This has required the development of new techniques to quantify the nature of aggregated suspensions, details of which are presented in this paper.

Jan 1, 1989