Search Documents

By Peck W

The tunnel alignments investigated for the Gosford Regional Sewerage Scheme are located in the Terrigal Formation and are covered for most of their length by a thick blanket of soil and weathered rock. The following techniques were found to be most effective in geotechnical investigations for tunnelling in this area: air-photo interpretation, seismic surveys to pinpoint drilling targets, in-situ measurements of strength,deformation modulus and permeability in cored holes, and the construction of rock- mass models. Cross-hole seismic modulus measurements, surface resistivity soundings and electric well-logging techniques were found to have limited applicability due to adverse local conditions.

Jan 1, 1976

CONTENTSIntroduction.Ore Bodies.Variations in Ore Dressing Practices.Stage I .Gravity Concentration for the production of a Lead Concentrate. 1909-1918.Stage Il Gravity plus Flotation Treatment for the production of a Lead Concentrate and a Zinc Concentrate. 1918-1929.Stage III All Flotation Treatment for the production of a Lead C~mcentrate and a Zinc Concentrate. 1930-1939General Summary - Stages I, II, III.Stage IV Gravity plus Flotation Treatment for the Production of a Lead Concentrate and a Zinc Concentrate. 1939-1947.1. General.2. Notes on Ore Dressing Practice.A. Gravity Section - Re~oval of Free Galena.B. Secondary Ball Mill Grinding Section. .a. Mineral Association.b. Composite particle problem.c. Degree of grinding required.d. Free Gangue Minerals in Table Tailing.

Jan 1, 1948

By Aziz N

The objective of the paper is to develop an understanding of the influence of caving on powered support rating by examining the geology and support performance at two sites which represent the current extremes in support rating, ie 6/240 Ton supports operating in the Hirst Seam at Solsgirth Colliery, Scotland, and 4/900 Tonne supports operating in the Bulli Seam, West Cliff Colliery, Australia. A conceptual model is introduced which considers the coal ahead of the face, the powered support, and the caved waste to be three yielding foundations which interact to control the subsidence of the roof strata. Different caving mechanisms are identified for the strata of the Hirst and Bulli Seams, ihese mechanisms being related to rock properties, ie to the palaeogeography and depositional conditions at each site, producing caved wastes with different yield characteristics. The results obtained for convergence and support reaction during production cycles at both sites are analysed to show the manner in which support reaction is developed, indicating the importance of high setting load densities in the Bulli Seam. Evaluation of the work done on the subsiding roof strata during typical production cycles by two of the yielding foundations, ie the powered support and the caved waste immediately behind the powered support, is used to further demonstrate the influence of caving mechanisms on support rating.

Jan 1, 1986

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995

By Brumley J

The development of the SECV brown coal open cut at Loy Yang will require depressurisation of aquifers both within and below the coal seam sequence in order to maintain open cut stability. Prediction of future open cut dewatering requirements at Loy Yang Open Cut and evaluation of the regional consequences of dewatering has required development of a detailed hydrogeological model of the Loy Yang area. The complex stratigraphy of the coal seam and aquifer/aquitard sequences at Loy Yang have been analysed and integrated with the hydrogeological concepts developed from regional groundwater studies to formulate a realistic hydrogeological model as a basis for finite-element flow modelling.

Jan 1, 1988

Amongst the Pacific Rim countries, Papua New Guinea (PNG) is the leader in new gold discoveries and developments leading to new production. PNG has shown a dramatic increase in gold production when taken from a base of about 600 000 ounces in 1984 to 1 160 000 ounces in 1986. 1987 is expected to produce about 1 500 000 ounces and new planned developments will give further large increases. PNG's leading position when compared with neighboring Pacific Rim countries is only partly due to its favorable geological setting along the "Rim of Fire" epithermal zone. More important have been well-thought-out mining development legislation and good administration as well as consistent taxation and royalty policies. A stable political environment and a track record of new mining developments over the last 15 years, both pre and post Independence in 1975, have also been important factors in encouraging the new developments. Early Portuguese explorers associated the New Guinea mainland with gold as early as 1525 but it was not un,11 1R77 that a small ill-fated gold rush gave the first recorded production at Laloki near Port Moresby. Modest but commercial discoveries were made in the outer islands and coastal mainland regions from 1888 to 1926. In 1922 William "Sharkeye" Park found gold at Edie Creek and this led to major discoveries at Wau and Bulolo which were the first large scale commercial gold Operations.

Jan 1, 1987

INDEX OF CONTENTSIntroductionThe slag samplesGranulated SlagGlass-spinel-magnetite-metallic leadRapidly Chilled SlagSlowly Cooled SlagSpinel - magnetite - zinc melitite (hardystonite) willemite - olivine -lead silicate - metallic lead - lead sulphide - copper sulphide - copper arsenide - nickel arsenide.ConclusionsIllustrationsINTRODUCTIONThis paper presents the results of a mineragraphic examination of representative samples of granulated lead blast furnace slags from the Port Pirie Smelter, and of slowly cooled samples of t:b.e same slags, undertaken at the request of the Broken Hill Associated Smelters Pty. Ltd., as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.THE SLAG SAMPLESThe chemical composition of the slags examined is given by the following three analyses of the granulated slags, supplied by the Broken Hill Associated Smelters (Table 1).

Jan 1, 1949

By Nye P. B, Fisher N. H

At the second Empire Mining and Metallurgical Congress held in 1927, the Empire Council of Mining and Metallurgical Institutions was formed and it was proposed that the Council take steps to prepare a "Review of the Mineral Resources and Industries of the Empire." At the third congress in 1930, it was resolved that the proposal to institute the review should be submitted to the Imperial Conference held in 1930. This was done, and the Minerals Committee, of the Imperial Economic Committee compiled, an interimreport which was based on statistics of imports and exports, and did not consider resources and consumption.In 1942 the Institution of Mining and Metallurgy, London, wrote to the Empire Council and stated that it was desirable that the Council should be in a position to take part in decisions affecting the future of the mining and metallurgical industries. The Council communicated with the constituent Institutions regarding the nominations of two members then in England. Subsequently the Mining, Geological and Metallurgical ,Institute of India prepared a review of the mineral resources and industries of India and their post-war development, and the Empire Council forwarded a copy to the Australasian Institute of Mining and Metallurgy and asked if that Institute would submit a review on simjIar lines for Australia. The Australasian Institute arranged that the Australian review should be prepared by...

Jan 1, 1946

By Boyd D. M

Minor magnetic anomalies which may be un represented on a magnetic contour map can be extracted from the original survey data and plotted by the described method to provide a rapid interpretation of the magnetic survey, provided that the data has been recorded digi- tally on magnetic tape. The example used comes from 40 kilometers south of Charters Towers, Queensland.

Jan 1, 1977

By Mason D. O, Tuckwell K. D

Whole rock geodhemical analyses from samples of Potosi gneiss within the Willyama Supergroup have been utilised to identify geochemical trends towards Pb/Zn ore positions. Although the analyses come from disparate sources they have been incorporated in the data base only if locational, sampling, analytical, lithological and stratigraphic descriptors were reliable. These data have been statistically analysed using programmes of the GASP software package. A discriminant function has been derived which permits Potosi gneiss associated with the Pb/Zn lode horizons in the Broken Hill domain to be distinguished from Potosi gneiss in a similar stratigraphic position in the Maybell Domain. In the "near ore" position the Potosi gneiss has significantly lower mean Na2O and significantly higher mean MnO. Also mean Rb, CaO and K20 are higher and mean Sr lower. This discriminant function serves to identify areas prospective for Pb/Zn mineralisation. A second discriminant function based on MnO, Si02 and K20/Na20 gives a semi- quantitative indication of proximity to ore.

Jan 1, 1983

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993

By Jones M

The concept of precise, accurate timing with Electronic Delay Detonators (EDDs) was first seriously addressed in the mid-1980s and much was made of the cheapness and profusion of digital watches in terms of the likelihood of EDDs also being cheap and easy to produce. Ten years later, with every major explosives company and many electronics groups having instituted projects to capitalise on the promise of these devices, production devices are still to come into general use. In South Africa, Expert Explosives units have been used in most applications during proving trials and more recently for production blasting in underground ring stoping and open cast coal. The outcome has been valuable learning both as to the benefits and technical requirements for electronic delay blasting, and especially, safety aspects. Examples are shown of production blasts which utilised the power of EDDs. It is evident that it is not delay accuracy alone which determines the value of these systems, but the whole robustness, flexibility and ease of delay allocation when harnessing blast engineering knowledge. Muckpile movement and shape, fragmentation and vibration frequencies have shown to be greatly influenced by designs which can be implemented no other way. The flexibility of a system and the power of the software controlling it are crucial in capitalising on blasting potential, which lies in integrating control of blast timing with other developing electronic Technologies.

Jan 1, 1995

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By Corner NG

A sea bed sampling programme by CRA Exploration Pty. Limited over an area of 12000 km offshore from Westland, Southland and Otago, New Zealand, led to the discovery of the Harvester Prospect, an area of some 67 km2 which averaged 189 mg/m3 gold in surface samples. This area was in water depths of 70 to 100 m and contained a high grade core of 33 km2 which averaged 283 mghn3 gold. The gold recovered was fine grained, averaging 124 microns, and indicated a potential resource of approximately 10 t of gold per metre of thickness. Interpretation of existing seismic and geological data suggested that the gold anomaly may be associated with a unit of sediments 10-40 m thick, probably deposited during a lower sea level stand. Two initial attempts at vibrocoring the anomaly produced inconclusive results. In 1989 a much more powerful vibrocorer with scaled up support facilities and a dedicated 24 It turnaround laboratory were employed. The final results clearly showed that the gold was from an uneconomic surface enrichment.

Jan 1, 1990

The phosphatic overburden of Christmas Island is a lateritic soil and consists dominantly of crandallite and millisite. These minerals are polymorphs of general formula, (Na,K)x Ca2-x (Al, Fe)6 (PO4)4 (OH)10-x (2+x) H2O. Iron occurs only in millisite. Both minerals exhibit similar thermal transformations, dehydroxylating near 600¦C and recrystallizing above 800¦C. Dehydroxylation results in crystal structure collapse but retention of crystal morphology. Ggethite, boehmite and apatite are minor constituents of some-of the phosphatic Soils.

Jan 1, 1971

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

By Best R. J, Poulos H. G

The method for design of primary roof support for the large todoidal cavern constructed to house the Sydney Opera House parking station is presented. The cavern was constructed with 5 m of rock cover beneath Sydney's Royal Botanic Gardens. Design of rock reinfonnent using a combination of fully grouted rock dowels and Macalloy bars was based on control of horizontal shear movement along bedding features in the roof. A combination of linear arch type analyses and non-linear jointed finite element analyses were used in the design study together with an analysis of the shear resistance offered by fully grouted bolts under shear deformation.

Jan 1, 1993

By Bloom M. S

Epithermal vein and breccia hosted Au mineralisation at the Kerimenge prospect, in the Wau district, Papua New Guinea, occurs within a block of multiply fractured dacite porphyry of Pliocene age, and is localised on intersecting regional fault structures, marginal to the eroded vent of a Late Pliocene-Pleistocene maar volcano (diatreme).Au mineralisation is primarily controlled by the steeply dipping Kerimenge Fault zone, which hosts a basal zone of silicified breccias,transitional laterally and vertically to networks of fracture controlled veins.Early quartz+pyrite veins, deposited from CO2 rich, NaCl saturated, boiling fluids pre-date the main phase of Au mineralisation. Four stages of Au bearing vein mineralisation have beenrecognised. Quartz+sulphide veins (stage 1) and partially coeval quartz+sulphide+carbonate+ adularia veins (stage 2) occur marginal to silicified breccias, and are associated with quartz+sericite+pyrite wallrock alteration. Similar depositional conditions prevailed for stage 1 and stage 2 mineralisation. Mineralising fluids underwent two stage boiling at temperatures of 145 to 2300 C. Boiling resulted in the loss of approximately 3 wt.% CO to the vapour phase. 2 Fluid salinity was probably I wt.% NaCl or less.

Jan 1, 1990

Various aspects concerning gold are mentioned below. These have no common theme but suggest points of interest any one of which, if warranted, could lead to development later and elsewhere. 'High level' auriferous gravels The gold deposits of Victoria are commonly classified as being either primary or secondary. Most primary occurrences comprise gold present in quartz reefs, together with other lode-like occurrences in which gold is associated with various sulphides, with or without quartz. Secondary occurrences are derived by physical release of primary gold and subsequent concen- tration of it as a constituent of sediments. Secondary gold deposits may be themselves eroded so leading to third or even fourth generation gold.

Jan 1, 1982

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004