Search Documents

Gekko Systems Pty Ltd have developed the Python Underground Processing Plant for the concentration of gold and sulfide ores. The Python plant has an established flow sheet including fine crushing, screening, gravity separation and flotation which aims to concentrate the valuable minerals (gold/sulfides). The aim of the plant is to achieve high valuable recovery into a mass yield of 10 - 30 per cent to reduce the amount of material that is needed to be taken to downstream processing. This paper examines the test work protocol for testing an ore to assess its suitability for the Python flow sheet. This paper will discuss the test methods employed to determine crushing requirements, continuous gravity recovery and flotation performance and how the results relate to Python design for the comminution, gravity and flotation circuits. Results from past test work will be discussed.

Aug 1, 2010

By R Jones

OneSteel Whyalla’s grate-kiln-cooler pelletising plant was commissioned in 1968 processing haematite feed from the local South Middleback Ranges mining area. The existence of a magnetite resource beneath the haematite ore at Iron Duke had been known for some time. In 2004, a decision was made to covert the primary iron source for the Whyalla steelworks from haematite to magnetite – known as project magnet. The intent of the project was to convert the feed to the steelworks from haematite to magnetite and to free up the remaining haematite resource for export. The pelletising plant was cut over to a magnetite feed in 2007.The thermochemical differences of magnetite compared to haematite are threefold:1. the introduction of an exothermic reaction during conversion of magnetite to haematite,2. the absence of bound water which existed within the haematite, and3. lower gangue content requiring lower fluxing levels and therefore lower calcination energy demand.The combination of these differences results in a significantly different induration requirement for magnetite as compared to haematite. The change therefore required extensive research and test work to design modifications to the furnace and to ensure appropriate risk mitigation for the Whyalla steelworks.Preliminary pot-grate test work was performed to define the pellet chemistry and confirm the suitability of the magnetite to produce pellets suitable for the OneSteel blast furnace. A heating curve was developed by use of computer-based heat and mass balance modelling. Extensive pilot scale grate-kiln-cooler test work was then performed to confirm the heating curve and to verify and fine-tune the pellet properties. Computation fluid dynamics was used to design the physical changes to the furnace required to achieve the proposed heating curve.Following installation of an additional preheat zone, including a wall and dilution air fans, into the preheating furnace, and installation of an additional wall into the cooler, the modified furnace was commissioning in December 2007. The plant performed as expected during commissioning with the actual heating curve matching the proposed curve and the produced pellets within blast furnace specifications.

Jul 11, 2011

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

By M Hilden, K Barbosa, M Yahyaei, C Ndimande, K Runge, V Jokovic

Classification devices provide a link between comminution and flotation. Basically, it determines which particles are diverted back for additional grinding and which ones pass to downstream flotation. Therefore, the classifiers play an important role in the performance of a mineral processing circuit. Hydrocyclones are the most common classifiers used in wet grinding, despite being associated with poor classification efficiency. Hydrocyclones are widely used due to advantages related to low maintenance as well as reduced capital and operating cost. Other classifiers, such as fine screens, have much better classification efficiency compared to hydrocyclones. The major challenge of using screens in an operation, however, is their large footprint and increased maintenance requirements relative to hydrocyclones. Some researchers have demonstrated that switching from hydrocyclones to screens, as the classifier device in a ball milling circuit, resulted in a 20 per cent increase in plant throughput and significant improvements in coarse particle recovery, resulting in a 6 per cent increase in overall flotation recovery. However, it is known that these benefits of improved classification are very much ore specific, ie depending on the ore response. Therefore, there is a need to estimate the benefits of improved classification in pilot scale testing before the plant could consider the potential classifier upgrade. This paper presents the results of two pilot-scale grinding tests where the ore sample was processed using different classifiers: a traditional hydrocyclone and hybrid classification involving the use of a semi-inverted hydrocyclone followed by a screen. The size specific energy and circulating load were used to compare the performance of the grinding circuit. The grinding product was subject to mineral liberation analysis and the impact of classification efficiency on the mineral liberation is discussed in the paper.

Aug 24, 2022

By M Wieloch, D Wimpenny, M Chappell

Fibre-reinforced geopolymer concrete (FRGC) contains no Portland cement or steel reinforcement, but instead uses synthetic fibre reinforcement and a geopolymer binder. The use of geopolymer binder in lieu of Portland cement reduces the concrete’s embedded energy (CO2 emissions) whilst the use of synthetic fibres eliminates the issue of reinforcement corrosion, thus enhancing the overall long-term durability of concrete. This paper presents the development of FRGC during a three-year project funded by the Victorian Science Agenda and a consortium of five organisations. The work involved laboratory and field trials and the production of prototype tunnel segments that have been subject to durability and fire testing.FRGC has exceeded the performance of the Portland cement-based control mix in terms of flexural strength, chloride diffusion, water sorptivity and drying shrinkage. Furthermore, the FRGC segments subjected to a simulated hydrocarbon fire test did not exhibit explosive spalling; however, the creep of FRGC was approximately three times that of the steel fibre-reinforced Portland cement-based control mix. The compressive strength and tensile splitting strength of the FRGC were also lower than the control mix. These differences need to be allowed for in the design using FRGC.Prototype bolted tunnel segments of up to 0.8?t mass have been produced from FRGC using standard production techniques and ambient curing. These were successfully produced within a 24-hour production cycle. Cut sections through the segments showed good compaction and even distribution of fibres. The estimated carbon footprint of tunnel segments produced using FRGC is approximately 70 per cent less than that of Portland cement-based segments containing 25 per cent fly ash and steel reinforcement.The results to date indicate that FRGC has the potential to produce a new generation of tunnel segments and, in general, precast concrete products with increased durability and substantially reduced carbon emissions compared to the Portland cement-based concrete with steel reinforcement.A summary of further research carried out by CH2M HILL into a complete elimination of ferrous inserts from segmental concrete tunnel lining is also summarised in this paper. The use of non-ferrous connectors for radial joints in combination with the FRGC technology in the manufacture of tunnel segments will effectively lead to development of a new generation of segmental tunnel lining systems.CITATION:Wimpenny, D, Chappell, M and Wieloch, M, 2014. Fibre-reinforced geopolymer concrete – an innovative material for tunnel segments, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Wynn, R A. Pax, S Mann, B Cornish

The semi-autogenous grinding (SAG) mill at the MMG Century operation has failing load cells that are essential to the control strategy used to stabilise the mill. Currently, mill-bearing pressure is used as a proxy for the load cells, but it has been found to be a noisy signal and lacking in useful sensitivity. It is also prone to variations and drift due to temperature. After consideration of a number of options, a non-contact acoustic array has been installed around the SAG mill to provide a more stable proxy load signal as well as other information about the internal operation of the?mill.The installation consists of 12 microphones to provide some detail into the operational differences that occur during normal operations at the MMG Century SAG mill. This acoustic approach acknowledges that operational grinding mills emit significant acoustic emissions that are a consequence of the dynamic environment prevailing inside them.Previous studies have attributed the acoustic noise to a range of events that occur inside these mills (Pax, 2011; 2012). Consequently, non-contact acoustic determinations of in-mill behaviour can provide powerful insights into the operation of the primary comminution tumbling mills. By measuring key microphone signal attributes at different positions around a mill, a holistic picture of mill internal operation can be developed.This paper will describe the installation of the 12 microphones and discuss the use of the acoustic load signals as a proxy for failing load cells. It will also present data from new observations of internal mill dynamics and the results of implementation of control using these acoustic signals. Key to the control approach has been the development of a logically coherent picture of the processes inside the mill.CITATION:Pax, R A, Wynn, R, Mann, S and Cornish, B, 2014. Implementation of acoustic arrays for semi-autogenous grinding mill?operation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 273–282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By P Woodward, T Ly, N Muhamad

OZ Minerals' Prominent Hill copper-gold concentrator is located 650 km north-west of Adelaide in the Gawler Craton of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a design capacity of 8 Mtpa. The flotation circuit includes six rougher cells, an IsaMill for regrinding the rougher concentrate and a Jameson cell preceding the three stage conventional cell cleaner circuit.Since its commissioning, the Prominent Hill flotation circuit has been the focus of a series of projects aimed at continual performance improvement. This has been achieved by a systematic approach of project identification, evaluation and implementation which has led to a progressive improvement in flotation performance. Innovations that have been successfully implemented include aspects of cell design and operation, and reagent suite optimisation.Improvements to the mechanical cells initially focused on the installation of a modified rotor-stator design in the rougher circuit, as recommended by Outotec. Isolated cells were fitted with this technology and proven to provide a benefit for copper recovery before the design was trialled in subsequent cells along the bank. Based on this success, further modifications were made to other aspects of the rougher and cleaner cells.Laboratory trials conducted at Prominent Hill involve a screening process identifying potential reagents from a list of products, which are then rigorously tested in the laboratory before one is selected for trial in the concentrator. Where these reagents have demonstrated a statistical improvement in performance they have typically been incorporated permanently into the flotation circuit. This paper discusses the process of continual improvement at the Prominent Hill flotation circuit and the optimisation achieved by the implementation of key initiatives.CITATION:Woodward, P, Muhamad, N and Ly, T, 2013. Optimisation of the Prominent Hill flotation circuit, in Proceedings MetPlant 2013 , pp 431-444 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J Simpson, M Johnston

Recently Mount Isa Mines undertook a study to review the lead-zinc orebodies to extent of resource and reserves and determine the new life-of-mine schedule, as the Mount Isa and Hilton orebodies had not be reviewed for many years. Also, the recovered value of the Mount Isa, Hilton and George Fisher orebodies had been increased by major performance improvements in the lead-zinc concentrator. The Mount Isa Lead-Zinc concentrator processes fine-grained lead-zinc ore from the Mount Isa, Hilton and George Fisher orebodies. These orebodies have varying levels of pyrite and large variation in the grain size and texture of the galena, sphalerite and pyrite. This variation has a large effect on the recovery of the lead and zinc in the concentrator. Some ores achieve 90 per cent recovery at target grades, yet other ores are unable to achieve æsaleableÆ concentrate grade, with no metal being recovered to concentrate and therefore effectively losing the contained metal to the final tailings. Models were created to predict the metallurgical performance of these orebodies, to better reflect the variation that occurs. These improved metallurgical models and economic data allowed the determination of the Net Smelter Return (NSR) for each block in the geological block model. This NSR is the return to MIM of the metals contained in concentrate. The NSR was used as the cut-off grade criteria when determining the value of the ore. This formed the basis of the lead-zinc life-of-mine schedule and the optimisation of the lead-zinc business.

Jan 1, 2003

By P Velletri, N Gaylard

The management of wear surfaces in mining operations has remained largely unchanged since the inception of mining. Sacrificial wear liners are installed on the inside of chutes, hoppers and other equipment used to transfer bulk ore to protect the asset from abrasive wear caused by the flow of material. These liners are generally replaced at fixed intervals which may be determined based on historical wear rates or may be driven by other maintenance requirements for that asset. This approach does not always yield satisfactory results, especially for critical assets where the impact of downtime on production can be substantial. For such assets, a condition-based maintenance strategy has the potential to significantly increase productivity and reduce the total cost of ownership associated with the asset. However, for such a strategy to be successful, timely information on the actual condition (remaining thickness) of the wear liners is essential. This paper describes the development and implementation of a wear monitoring system that can be used to remotely and continuously report on remaining liner material thickness in real time. It details some of the challenges that were overcome when developing the system, including the design of a patented thickness measuring system that can be used in a variety of liner materials and is tolerant to the presence of ore on the wear surface. The paper also explains how a cloud-based approach enables data from the wear sensors to be integrated into external systems such as a data historian, which has been demonstrated through a collaborative project with one of the largest iron ore producers in the Pilbara. This ability to combine real time liner thickness information with other data sources, such as throughput, provides the foundation for the transition to a condition-based maintenance strategy.

Nov 8, 2021

By H Asche

The Melbourne Metro project has evolved from the Victorian Transport Plan. MM1 is the second major phase of the proposed separation of Melbourne’s radial railway system, creating a line that will operate independently across the metropolitan region. The central section will run beneath the inner suburbs and the central city. The initial project comprises nearly 8 km of twin bore tunnels, three cavern stations and two cut and cover stations, as well as a dive structure and connections with the existing rail system. This paper describes the development of the geological model, a modification of the rock mass classification system derived during the EastLink project and the influence of the geology on the design of the tunnels and stations for the Department of Transport’s business case.The majority of the tunnelling will be in the siltstone and sandstone bedrock. This material has been extensively folded, sheared and intersected by igneous intrusions. A revised rock mass classification system has been developed for the Melbourne Formation to assist in identifying the important engineering properties of the rock and to rationalise the support types required.The Metro’s tunnel alignment crosses the Yarra Delta deposits in the lower reaches of the Moonee Ponds Creek and again at the Yarra itself near Princes Bridge. These deposits vary in extent and thickness over very short distances. The investigation of these materials has been carried out using conventional drilling techniques in conjunction with sonic drilling methods.Over the central section of the Metro, the positions of the new station are determined largely by transport planning requirements and urban development opportunities. However, the stations, and the tunnels, have been the subject of studies, optimising exercises, and selection processes to arrive at the concept design. This paper describes the influence of the varied geology on the development of the design, and the identification and management of the risks in tunnelling under the centre of Melbourne.

Mar 8, 2011

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By F Diaz, G Hovestadt, B Friedrich, D Latacz, M Sommerfeld

The metallurgical sector significantly contributes to the global carbon footprint and encounters the challenge of developing more sustainable production methods. This study introduces novel approaches aimed at reducing CO2 emissions within the industrial sector, some of which have been developed up to the demonstration scale. In two case studies, urban waste from the agricultural sector (corn, olives, coconut etc) and waste electrical or electronic equipment (WEEE) recycling residues (shredder light fractions (SLF)) were subjected to thermal treatment. The resulting materials were then used as substitutes for conventional fossil-based reducing agents in both the copper and ferroalloy industries. Furthermore, hydrogen was employed at different scales to assess its efficacy as a reducing agent for recovering metal oxides from fayalitic copper slags. Our findings reveal promising prospects and defined specific challenges for the integration of these alternative reducing agents in the industry. The synergistic use of pyrolysed SLF, bio-coke, and hydrogen presents a viable pathway to significantly diminish CO2 emissions while simultaneously improving the sustainability of the metallurgical sector.

Jun 19, 2024

No Paper

Jan 1, 1996

By B J. Monaghan, R J. Longbottom, S Prabowo, D Del Puerto, B Maisuria, C W. Bumby

The use of hydrogen as a reducing agent can substantially reduce carbon dioxide (CO2) emissions from the ironmaking process. Iron ore fines can be reduced in a fluidised bed (FB) using hydrogen (H2) at high temperatures (>800°C), although several studies have reported the sticking of particles which causes the bed to defluidise, effectively shutting down the process. Here, we report results from the reduction of New Zealand (NZ) titanomagnetite (TTM) ironsands in a small-scale laboratory FB (100 g) at temperatures between 800–1000°C using H2 flow rates up to 5 standard L/min. No sticking phenomena are observed under any of these conditions, which is attributed to the formation of a stable titanium-bearing oxide layer on each particle’s exterior, preventing iron-iron contact at the particle surfaces. Pre-oxidised NZ TTM ironsands have also been studied and shown not to stick. Interestingly, at lower reaction temperatures the reduction kinetics for pre-oxidised ironsands is faster than for as-received ironsands. This increased kinetic rate can be attributed to the preoxidation stage inducing micro-fractures that create a void for the hydrogen to diffuse into the inner regions of the particle. In addition, oxidation of TTM appears to segregate the particle into two distinct phases, a high Aluminium-Magnesium (Al-Mg) phase and a high Titanium (Ti) phase. The findings are important as increasing the operating temperature of the FB reactor results in a faster reaction rate and higher gas utilisation, making the process more economically attractive. Furthermore, oxidation of NZ TTM ironsands results in a faster reduction rate at lower temperatures (800°C– 900°C) opening the opportunity to reduce the reaction temperature which might be beneficial in a final commercial-scale process.

Sep 18, 2023

By A C. Edwards

The Mesozoides of North-Eastern Asia represent a collage of exotic terranes which were accreted to the margins of the Siberian continent. In the Late Precambrian and Phanerozoic, the passive margin of the Siberian continent (the current north-east) broke up into a number of discrete fragments as a result of rifting events in the Riphean, Early and Middle Paleozoic. Rift related mineralisation includes stratiform and stratabound copper and base metal mineralisation in the structures of the Omulevka, Okhotsk and Prikolyma basement terranes, as well as along the edge of the Siberian continent in the Paleozoic sediments of the Verkhoyansk passive margin. During the Late Mesozoic the terranes were reassembled in a series of accretionary events. At the end of the Jurassic, the velocity of the Kula plate increased, and the opening of the Canadian Basin in the Arctic commenced, changing the vectors along which the Siberian and North American plates moved. Island arcs terranes were pushed back onto the Omolon super-terrane which was in turn pushed onto the Siberian Craton in a series of massive collisional events that resulted in the restructuring of the whole region. Numerous granitoids characterised by collisional and island arc chemistries with Au and accompanying Sn, and W mineralisation were emplaced. Mesothermal gold-quartz mineralisation was emplaced in a series of narrow belts that adjoin major crustal sutures and that spatially overlap belts of granitoids and zones of subgreenschist metamorphism. Each of these gold-quartz vein belts corresponds with a specific collisional phase. In the middle Cretaceous, the Okhotsk-Chukotka volcanic belt developed along the paleo-Pacific margin of the Siberian continent. Epithermal Au-Ag developed in the volcanics and shallow mesothermal Au-Ag-quartz and Au-Sb mineralisation developed in the Mesozoides. Porphyry and skarn style mineralisation developed in both the island arcs and in the continental Okhotsk-Chukotka Volcanic Belt.

Jan 1, 1999

By N Redwood, N Fowkes, A Bassom, S Durkin

"It is well known that from time-to-time a vehicle will interact with a bund or windrow and often the barrier is insufficient to safely arrest that vehicle. The result of such an incident is often catastrophic. Regulations around the requirement for edge protection near pit edges vary between jurisdictions. Generally in Australia regulations tend to be around placing the responsibility on the mine operator to provide ‘adequate’ or ‘appropriate’ edge protection. Guidelines often place a minimum height of bund at between half and two-thirds the diameter of the largest tyre on-site.Safescape has identified the opportunity to improve safety in open pit edge protection and is currently developing the Edge Protector (EP) product. The EP is designed to create a vertical front face to a conventional broken rock safety bund. The fundamental premise of the product is that by creating a vertical front face to the bund, trucks cannot easily drive up over the bund and instead have to push through the rock to get to the other side.In addition to providing a safer system for arresting vehicles, the vertical front face also means that extra space is made available in the haul road. This can either be used to facilitate larger trucks or when designing a new mine, with an increase in overall pit slope.This paper outlines the research and development of a new edge protection product. Discussion will include project objectives, economic incentive for mines to apply the system, mathematical analysis of the truck/bund interaction and physical testing of the product.Citation:Durkin, S, Fowkes, N, Redwood, N and Bassom, A, 2016. Innovative Approach to Open Pit Edge Protection, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 138–149 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By S K. Panda, M A. Van Ende, S Chatterjee

Tata Steel Netherlands (TSN) aims to reduce its CO2 emissions by 35–40 per cent by 2030 and become CO2 neutral by 2045. A first step to reach these targets is via the utilisation of an Electric Arc Furnace (EAF), which will run on a mixture of high proportion of Direct Reduced Iron (DRI) and scrap. For an EAF operation, optimisation of slag chemistry is important to achieve the right mix of basicity (for refining especially dephosphorisation), foaming, volume (rate) and refractory life. Slag composition and rate can vary widely depending on the process variables like charge mix, charge composition, feeding rate, oxygen lancing, external carbon injection/addition, fluxing and refractory erosion/corrosion. Moreover, it is important to note that the slag composition and rate are ‘transient’ parameters and change throughout the heat. This makes all the dependent phenomena and/or outcomes transient as well. To describe all these effects simultaneously and be able to realistically simulate the EAF operations, a validated dynamic process model is important in the absence of real plant data. In this study, a validated dynamic EAF process model based on the concept of Effective Equilibrium Reaction Zone (EERZ) has been utilised to analyse the impact of high DRI industrial scale EAF operations on the transient slag characteristics – including slag volume (rate), composition, phases, solid fraction and viscosity. Simultaneously, the model is able to predict the impact on steel and offgas characteristics. Case studies were performed with 70 per cent DRI:30 per cent scrap mix considering both low and high-grade DRI. Both melting and refining aspects of the process including continuous feeding, arcing program, carbon addition, fluxing and oxy-lancing were considered.

Jun 19, 2024

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022

By Dean J. A, Taube A, White A. H, Messenger P. R, Jones I. W O, Huston D. L

The 50 million tonne Mount Morgan gold-copper deposit (4.99 g/t Au, 0.72 per cent Cu) was an irregular pipe-like body of quartz and pyrite, with subordinate chalcopyrite, magnetite and gold. Mineralisation was hosted by the Middle Devonian Mine Corridor Volcanics which occur as a roof pendant within the Late Devonian Mount Morgan Tonalite. On three sides, the deposit was enclosed by a series of normal, concave, listric faults and surrounded by outward-dipping Mine Corridor Volcanics. The tonalite which bounded the western side of the deposit transgresses the domal structure with no apparent interference. A pipe of intense, texturally-destructive, quartz-sericite-chlorite ¦ pyrite underlay and partly surrounded the deposit.The volcanic setting of the deposit, its shape, metal content and associated footwall alteration are consistent with a subsea-floor replacement origin for the gold-copper mineralisation. Mineralogical studies have confirmed the deposit has been recrystallised and annealed by a thermal metamorphic event, most likely the intrusion of the Mount Morgan Tonalite. Pyrrhotite Pipe mineralisation replaces annealed massive pyrite, suggesting that it formed during retrogressive metasomatism associated with tonalite emplacement. Telluride minerals have a close association with chalcopyrite, and no evidence for a late telluride paragenetic stage was observed. Telluride mineralisation is inferred to be genetically related to the massive sulphide mineralisation, and a separate magmatogenic origin for this mineralisation is discounted.

Jan 1, 1993