Search Documents

By Poole GR

An unusually high flow of water from an oxtr.iction panel in Wongawilli Colliery pr,;npted the investigation of the possible sources of the water. It is more probable that water is derived f r,m sources adjacent to or within the Woo ' iwi 1 I i Coal rat her than by direct t r.onnuni n i"n from any surface source.

Jan 1, 1986

By B J. Wight, R Mackay, S Kim

Improving the understanding of the processes governing ground movements in and around brown coal open cuts is of significant interest for both operating stability and rehabilitation. Brown coal, lignite, is a low-rank coal that is best described as a soft rock, with geotechnical characteristics that derive from its organic origin. It is well-known that low-rank coals exhibit creep behaviour; however, little has been reported on the impacts of chemical processes on brown coal creep behaviour even though organic substances are susceptible to chemical alterations and mining processes will contribute to changes to the geochemical environment; around most mines, groundwater flow patterns are altered leading to enhanced surface water infiltration. Here we study the deformation behaviour of brown coal in response to ion exchange reaction. Our experimental results show that for different ion exchange conditions different characteristics of secondary compression are observed. With the addition of Ca2+, the ratio between coefficients of secondary and primary compression (Ca /Cc) initially decreased, presenting a minimum value at the concentration of 0.005?M, then increased significantly. This implies the importance of ion exchange process for the long-term deformation of brown coal. On the other hand, increasing Na+ concentration did not affect Ca /Cc values significantly over all tested concentrations. The suppression of diffuse double layer was still observed for Na+-treated samples as increasing Na+ concentration decreases Ca values. From a practical perspective, this study did not consider the tertiary creep behaviour and eventual creep failure.CITATION:Kim, S, Mackay, R and Wight, B J, 2014. Creep due to chemical alteration of rocks – a case study in brown coal, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 61–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

In preparation of this Paper, the emphasis has been laid on the commercial rather than on the technical and scientific aspects of coal evaluation. It is intended to describe and comment on the principal factors which currently determine the selection and procurement of coking coal for the steel industry, and is not based on the results of any original research by the author. Evaluation of different coals for strictly thermal uses, for gas production or other chemical applications has not been attempted, and comparisons of coal with other fuels have been excluded: the paper is concerned only with coals for the production of blast furnace coke. The discussion is strongly related to, and illustrated by, British, and to some extent, other Western European practice, but it is hoped that the general conclusions may have a wider application.

Jan 1, 1975

By Pattinaja MA

Mathematical modelling was carried out to determine the probable convergence and vertical stress patterns around a retreating longwall panel in an underground coal mine in New South Wales. An 'Electrical Resistance Analogue' and a program called 'THREED' based on the displacement discontinuity method were used for the modelling. Parts of the obtained results are presented here and compared with some measurements of convergence at the site. The modelled and measured data agree better qualitatively, than quantitatively.

Jan 1, 1986

By Swann CA

In order to meet export sales requirements from 1983 onwards, Amcoal developed a new underground mine in the Witbank area of the Transvaal. The mine was required to produce 5 million tons of run of mine coal per annum giving rise to 4 million tons of saleable products. A description of the coal processing plant is given with comments on design philosophy and design parameters. Main features of the coal processing plant are the raw coal handling facilities, centralised control and data capture and the loadout station. The management systems applied during the commissioning period are described. The difficulties experienced and their solutions are discussed. Commissioning was concluded with an independent plant performance test.

Jan 1, 1986

The title of my presentation is `Nursing One's Resources', words that fit a young organisation like Ross Mining and words we had to apply to reach our current level as a company. To get to where we are, we had to nurse, foster and treat carefully all our available resources in the widest sense of the word, namely: ò a stock or supply that can be drawn upon (funds, mineral resources, human resources); ò the means available to achieve an end; ò skills in devising expedients; and ò practical ingenuity. I do not claim that Ross Mining is now the perfect mining company. However, we have become a profitable, dividend- paying, gold mining and exploration company which is to our knowledge, currently the cheapest gold producer on the Australian continent. Nursing our resources got us where we are and will guide us in our future development. The words `nursing one's resources' are I feel particularly applicable to mining-as I like to argue that the extractive mining industry has a social responsibility to optimise the metal output and value from each orebody which is being exploited, and preferably leave no metal behind. Likewise, a modem company cannot survive into the future without maximising and optimising its human resource potential. In this presentation I would like to present a number of actual examples of nursing one's physical and human resources. Before I do that, I will give a brief background to Ross Mining. Ross Mining NL is a young Queensland-based company that gained its stock exchange listing in September 1987 and that poured its first gold in 1989 from its own developed Belyando Mine, located in Central Queensland. We have now reached the stage of a medium-size gold producer, producing approximately 70 000 ounces of gold per year, mainly from the Yandan Gold Mine, also in Central Queensland. Our production is set to increase to over 100 000 ounces in the near future. Recent increases in our resource base have secured us a future of ten to 15 years. As a young, newly listed company, we faced all the dangers that most new small floats do as a new entrant into an established industry. However, one advantage of being young and perhaps naive, is summed up by the following Zen Buddist saying: In the beginner's mind there are many possibilities, in the expert's mind there are few. A mining company's main assets are the sum of its resource base and the skills and talents of its people. Attempting to optimise both the physical and human resources within the company has been to-date the key to our success. The first example I would like to present is linked to the exploitation of the Belyando Gold Mine in Central Queensland.

Jan 1, 1995

By Noakes MJ, Willsteed TV

In the past few years an elevated gold price has resulted in the evaluation of many small scale surface gold deposits in Australia typically containing about 2-3 g/t Au. Operators have tended to assume that at the lower end of the grade spectrum only heap leaching is economically possible whereas above some assumed "cut-off" grade, carbon-in-pulp or similar techniques can be considered to have economic advantages.Studies made on a number of these prospects has indicated that this rather arbitary choice of treatment method can be mis-leading.A case study has been prepared assuming a "typical" situation and is presented. The deposit contains three million tonnes of ore assaying 3 g/t Au and is amenable to open pit mining methods. The mine site is remote but accessable and existing infrastructure is minimal. There are no unusual environmental constraints.

Jan 1, 1984

By Boshou B

In China, there are approximately 3,000,000 million m3 of gas (methane) included in highly gassy mines liable to coal/gas outbursts; the amount of methane pre-drainage possible is estimated at 400,000 - 500,000 million m3. At present, methane drainage has been carried out in 110 mines with a total amount of 19,000 million m3 methane produced during the period of 198 1- 1986. The methane drainage in coal mines of China can be divided into three types: from adjacent seams, from working face seams and from goafs, all with good results. In recent years, general attention has been paid to integrating methane drainage into the mining system but methane drainage from old goafs has to some extent been developed as well.

Jan 1, 1988

Roller seed screens were installed at The Broken Hill Proprietary Company Limited (B.H.P.) Whyalla pellet plant to replace vibrating screens on the green ball circuits. The installation of roller screens was justified by improving the sizing of the green balls. This improved sizing increased the yield of fired pellets produced from green balls thus decreasing the fuel consumption. The fired pellet sizing was improved also. This paper discusses the configuration of the roller screens installed at Whyalla, quality of green balls produced, advantages of roller screens compared with vibrating screens and future development of roller Screens.

Jan 1, 1984

In the first half of 1987 two four metre diameter raise bore holes were drilled at the Olympic Dam Project for ventilation purposes. The first hole, 476 m x 4.0 m diameter was completed in 96 days, 35 days longer than scheduled. The second hole, 407 m x 4.0 m diameter was completed in 39 days, 2 days ahead of schedule. Both holes were drilled with a Robbins 121R rig using a Wirth head that consisted of 23 face cutters and 5 side cutters, supplied by a contractor. After the sites were located a grouting program was carried out to help seal off an aquifer between 160 and 180 m below the surface. Cavities discovered in the Andamooka Limestone were filled with concrete. Because of the overlying dune sands and clay both sites were pre-sunk to the competent Andamooka Limestone.

Jan 1, 1988

By Hayes P. C

The reduction of small, dense zinc oxide (ZnO) samples in CO/CO2, and CO/N2 gas mixtures has been investigated at temperatures between 900 and 1100¦C. The microstructural characterisation of the reacted and partially reduced samples was complemented with measurements of the rates of the reactions. The mechanisms and kinetics of reduction of zinc oxide were found to be dependent upon the CO partial pressure, the oxygen potential of the gas mixtures, temperature and degree of reduction.

Jan 1, 1991

By Fitzgerald DE, Taverner MG

The principles, fields of application and equipment design concepts of several new approaches to continuous vacuum treatments of molten metals and alloys are discussed. Partic- ular attention is paid to the results of pilot plant tests evaluating a launder-in-tube method of 1. continuous production of refined zinc from a zinc-bearing lead produced in the lead splash condenser of the Imperial Smelting Furnace (ISF), and 2. continuous refining of crude cadmium. The former trials were not sufficiently encouraging to justify consideration of the process for commercial development. The applic- ation to cadmium upgrading gave very promising results; metal of 99.99 per cent purity was produced continuously at pilot scale (120 lb per hour) from crude metal containing 5.0 per cent Pb.

Jan 1, 1972

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

By Black LP, Law SR, Oversby BS, Mackenzie DE, Wyborn D

Three volcanic sequences of different ages occur close together in the Burdekin Falls area, southeast of Charters Towers in northeastern Queensland. The oldest is equated with the Cambro-Ordovician Mt Windsor Volcanics, and consists mostly of strongly deformed, regionally metamorphosed rhyolitic lava and minor feldspathic to quartzose sandstone. This unit is overlain by folded but unmetamorphosed Upper Devonian-Lower Carboniferous volcanics (DCv) of the lowermost Drummond Basin sequence. The primary volcanic facies of (DCv) principally comprises andesitic and rhyolitic lavas, and dacitic ignimbrites. Similar volcanics are widespread in the lowest formations of the Drummond Basin sequence elsewhere, and dominate that sequence east of the Anakie Inlier. The youngest volcanic sequence is Late Carboniferous and composed of lower, more deformed, compositionally diverse ignimbrites, lavas and conglomerates, overlain by generally less deformed rhyolitic ignimbrite sheets. The upper part is equated with the Bulgonunna Volcanics which extend 90km south to the Mt Coolon area. The Burdekin Falls area contains an ignimbrite stratigraphy different from that in the south. However, one of the most voluminous ignimbrites (Locharwood Rhyolite) in the southern stratigraphy is also present in the north, enabling the two to be correlated.Each of the three volcanic sequences reflects proximity to eruptive sources. Both the volcanics at the base of the Drummond Basin sequence and the Late Carboniferous volcanics are largely the products of subaerial eruptions. The former were erupted from several intermediate-composition volcanoes, and the latter from multiple-vent silicic calderas. All three sequences are considered to be prospective for precious and/or base metal mineralisation. Polymetallic massive sulphide deposits occur in the Mt Windsor Volcanics farther west, and many epithermal gold prospects and mines are hosted by the volcanics at the base of the Drummond Basin, especially east of the Anakie Inlier. The Late Carboniferous volcanic sequence is deeply eroded, and co-magmatic high-level plutons are widely exposed; this sequence may therefore be more prospective for deeper-than-epithermal mineral deposits.

Jan 1, 1990

By P J. Harris, D J. Bradshaw

Surface oxidation of sulfide minerals, such as that found in the regions of a sulfide ore body near the water table, can have a significant impact upon flotation. This theme has been explored for Merensky ore type sulfides where an ore containing pyrrhotite, pentlandite and chalcopyrite was thermally oxidised and the role of potential remedies investigated. Back-scattered scanning electron microscope images are presented showing the oxidation layer which formed in the mineral surfaces. These oxidation layers were depleted in both sulfur and iron with incorporated oxygen. Flotation recovery rapidly decreased with increasing oxidation, particularly after 27 days and reached a plateau after 50 days. Up to 27 days, this effect could be partially overcome with higher collector additions. Oxidation had more impact upon the finer size fractions, particularly for pyrrhotite. For more heavily surface oxidised samples, ultrasonic treatment prior to collector conditioning was found to improve flotation recoveries. This treatment had the greatest effect upon chalcopyrite particles. Sulfidisation was successful in restoring the flotation recovery of the heavily oxidised sulfide minerals. Longer sulfidisation conditioning times were not conducive to good flotation recoveries of both oxidised pyrrhotite and pentlandite due to oxidation of the freshly formed sulfide surfaces. For maximum flotation recoveries of oxidised pyrrhotite, pentlandite and chalcopyrite, different sulfidisation conditions are indicated. It appears likely that in a mineral processing operation treating oxidised Merensky type ores, two stages of sulfidisation employing different conditions would be required.

Jan 1, 2005

Commercial or potentially commercial deposits of coal occur in Australia in strata ranging in age from Permian to Tertiary. The coals of each period tend to show a community of petrographic character and significant differences as compared with coals of other ages. In particular- many of the Permian coals are unusually rich in inertinite whereas the Jurassic and Tertiary coals are typically very rich in vitrinite. The majority of the coals show evidence of deposition in environments subject to relatively minor marine influence. Except for some Tertiary and Permian coals the content of mineral matter tends to be high. Outcrops of coals of bituminous rank appear to be largely restricted to the eastern margin of the Australian continent. In this region vertical rank gradients are generally higher than in the other sedimentary basins and uplift and the removal of cover has occurred to a greater extent. To the west of the Tasman geosyncline, coal of bituminous rank generally occurs at considerable depths (usually in excess of 1 km and in some areas only at depths of over 2 kms), and in most areas coals at shallow depth are of sub-bituminous or brown coal rank. The controls of the distribution of coal type and rank have considerable economic significance and the unusual characteristics of Australian coals, especially with respect to coal type, make the direct application of overseas technology to Australian coals inappropriate.

Jan 1, 1975

By Harbort G. J

Jameson cell pilot plant trials were conducted in a number of areas in the Red Dome gold/copper flotation plant during 1991. The aim of testwork was to reduce the amount of cyanide soluble copper reporting in tailing to the gold leach plant, and hence reduce cyanide consumption. A number of these tests were conducted in parallel with conventional flotation columns. Laboratory tests were conducted to simulate the performance of the existing plant when compared with the addition of the Jameson cell allowing an extra sulphidising phase. This paper reviews the comparison of the Jameson cell and conventional columns in recovering cyanide soluble copper, while maximising copper concentrate grade. Key parameters that are investigated are residence times, air/pulp ratios, superficial gas recoveries and size by size recoveries. A brief comparison of performance of the Jameson cell and column in the controlled potential sulphidisation process is also presented. An estimation of the reduction in cyanide consumption is given.

Jan 1, 1992

By Fabjanczyk MW, Aziz NI, Hii J

The paper presents the results of a series of pull out tests performed on roof reinforcement systems currently being adopted in mines in Australia 7mm wire, dividag bar, 15.2mm strand cable, and birdcage cable. The study also investigated the load deformation chara- cteristics and the various design parameters controlling the effectiveness of a cable-grout system. Suggestions for continued work are Highlighted.

Jan 1, 1986

By Else D

While the underground mining work environment may have processes and equipment considered unique, most of the broad issues likely to affect the occupational health and safety of employees are not. One such occupational health and safety issue that is common to the mining sector and most other industries is noise. Noise as an occupational health and safety issue is of national significance. Presently noise induced hearing loss costs Australia around $35 million per year on compensation claims experience alone. Noisy equipment and work environments are still being tolerated in parts of the mining industry as `part of the job'. Where work has been undertaken in noise management, considerable emphasis has been placed on either industrial hygiene monitoring programs or the provision of hearing protectors to miners working on or around noisy equipment.Opportunities for more cost-effective and long term methods for controlling noise exist. Ready to apply solutions to noise problems in the mining industry are available, but for many mining operators this information is often difficult to obtain. To overcome this problem, the SHARE program collects and distributes solutions to occupational health and safety problems. The program aims to help organisations to close the gap between what is known about solving health and safety problems and what is actually being applied at the shop floor level: Recent developments have incorporated the SHARE program concept into worksite hazard management projects that involve the participation of employee representatives, front line supervisors and engineering personnel. Besides providing workforce members with an increased understanding of hazard management skills, the SHARE in-house program results in the implementation and sharing of solutions to health and safety problems by the program participants.

Jan 1, 1992