Search Documents

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

By P Bartlett, K Naidoo

Premier Diamond Mine is planning a new, mechanised, block cave, with a production level approximately 1000 m below surface. A high degree of tunnel damage is expected, due to stress and the relatively low in situ strength of kimberlite. An evaluation of the timing of tunnel excavation, tunnel size and spacing has been carried out to define critical parameters for planning layouts and development schedules. Extensive use has been made of three-dimensional FLAC3D numerical models, calibrated against known rock mass behaviour at 650 m depth, to examine the influence of undercut advance on production level excavations. These were able to represent the effect of stress rotation on tunnels during undercut advance and the effect of an inclined undercut. The analysis has provided guidelines that are possibly applicable to any deep block cave layout. The choice of drawpoint layout is of considerably less significance than the proportion of ground extracted on the production level elevation prior to advancing the undercut. The analysis shows that damage to production development will be potentially severe if it is all excavated prior to advancing the undercut, or is mined directly beneath the undercut face. The development of the main production tunnels alone ahead of the undercut may be feasible, but no breakaways should be put in as they appear to trigger a rapid increase in the severity of damage. The optimal sequence is when all production tunnels are developed at least 10 m in plan behind the undercut, where the induced peak field stress is less than 20 MPa and a maximum support pressure of 100 to 500 kN/m2 is require to contain movement. The assessment showed that the conditions are not significantly improved by increasing drawpoint spacing from 15 m to 18 m. The vertical spacing between the undercut and production level beneath is investigated. Provided production level development is carried out beneath the undercut, there would appear to be little benefit in increasing the vertical spacing between the undercut and production level beyond the current 15 m to 18 m.

Jan 1, 2000

At the Waikato North Head Ironsand operation, NZ Steel Mining Ltd is using a Bucket Wheel Excavator û shiftable conveyor mining system to excavate Titanomagnetite bearing sand and clay. The system utilises two Bucket Wheel Excavators with a two level shiftable bench conveyor and common trunk conveyor to deliver the material to a processing plant. The system was commissioned in November 1984 and has proved itself to be a high capacity, low cost method of excavating. Techniques of handling high sand faces have been developed and the conveyor layouts are going through a process of change to cope with the variable geo technical conditions and remain within: the characteristics of the excavators. The safety requirements for operating the system have been of a high standard and the experience has increased the confidence of the Company and the Mines Department Inspector's, for the first Bucket Wheel Excavator Mining system in New Zealand.

Jan 1, 1986

By R Knight

"In project evaluation there are two matters of keen interest to non-executive directors: the process by which an investment recommendation is reached, as well as the investment itself, as presented. It is sometimes mistakenly believed that Boards of directors are interested only in the result. That is not so. The process by which project evaluations are derived and socialised with the Board is as important as the result, sometimes more so.Setting aside the gloomy predictions of the doomsayers and looking through short-term volatility in supply and demand, the overall availability of mineral resources more often than not exceeds demand. There are in reality more development projects in prospect at any one time than are needed to meet the market. Only the fittest will prosper, although some others may survive.Optimism springs eternal in the mining industry and every project promoter, executive or entrepreneur has a convincing project development case. Some will create value for shareholders, but the historical evidence suggests that many will fail to meet the expectations set in their evaluation.Boards of directors make the final decision to invest, or not, in a new mine. Knowledge is power, and on that basis the balance of power favours management. Management has the facts (or in some cases, what passes for fact) and the passion to invest. The non-executives have the power of approval – yes or no – but before making a decision directors must demonstrate due diligence, the essential precursor to project approval.Management has a vital part to play in facilitating that due diligence process and in encouraging the independent thought processes of the Board. A closed approach by management fosters a negative, risk-averse attitude on the part of the Board. One that encourages an understanding of the rigour of the project evaluation process and the robustness of the result will allow directors to understand better the implications of their decision.CITATION:Knight, R, 2016. Project evaluation – a non-executive director’s perspective, in Proceedings Project Evaluation 2016, pp 11–19 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By W R. Adamson

"Optimisation of drill and blast design and engineering can deliver a significant positive impact on the profitability of any mining operation; however, true engineering of the blasting process is less common than might be thought. The paper that follows explores this gap and suggests a process control-based approach to the challenge.The concept of applying modifications to drill and blast designs in order to achieve efficiency improvements in downstream mining processes is far from new. However, the author suggests that the practical application has become less than rigorous in a number of different sectors of the mining industry in a wide range of countries.There is a common tendency for the design process to become simplified to the point where the objective is merely the communication of instructions to field implementers (drillers, explosive suppliers, blasters, etc). In effect ‘design’ often degrades to ‘cut and paste’ with consequences that vary from mild to critical, with respect to the profitability of the business.Engineering of the drill and blast process involves the design function, not on a one-off basis but rather as a component of a more complete cyclical process that includes a statement of objectives, a design based on a suggested hypothesis, field measurement of results, comparison with the target ‘set point’ and the application of control measures followed by new measurement, including interpretation of the results in financial terms.When applied in this fashion, engineering provides practitioners with the means to optimise the drill and blast impact on the full spectrum business result of the mining activity.These concepts are discussed with reference to a surface gold mining operation applying run-of-mine heap leach extraction. Engineering optimisation by adapting process control and measurement techniques is demonstrated to be a key component of the solution set applied to generate enhanced operations productivity and stakeholder value. It is shown that a combination of rigorous measurement, model calibration and hands-on quality assurance/quality control facilitates the creation of a road map to profitability, stressing the need to consider economic trade-offs between operational expense (investment) and measurement of enhanced value (return on investment).The process, however, does not cease at this point. Implementation of true design practices, incorporating innovation and discipline in implementation or execution can drive the process to deliver demonstrable, technically validated outcomes. Furthermore, these technical results can be related to financially quantifiable impacts. However, this accomplishment does not guarantee that these gains or savings will reach the bottom line of those mining, quarrying and construction companies that begin the process with such high hopes.CITATION:Adamson, W R, 2015. Application of engineering discipline and a full-process optimisation focus – productivity to profitability without profuse pruning, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 3–12 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 24, 2015

By M Scoble, W S. Dunbar

This paper reviews methods for grade estimation in short-term mine planning for block caving. Two particular tools are used: Ordinary Kriging and Simple Kriging with moving averages. It is also considered the influence of draw characteristics on the grade estimation process. Reference is made to mine case study data and analysis. These demonstrate that operational grade estimation is not a trivial process. It must take into consideration: the grade variability (in terms of ore and dilution), sampling interval, geological and geotechnical characteristics, geometrical layout and draw characteristics. Significant improvements appear possible in short-term planning if variogram analysis, as well as kriging methodologies, are introduced into the operational grade estimation process.

Jan 1, 2000

THIS paper is not intended to be a detailed description of the lead, smelting plant at Cockle Creek, as this has been covered in previous papers for the Institute in 1918, Proceedings No. 31, by other members of the staff; but the idea is to give some of the practices and conditions peculiar to these works, also to give some experiments carried out and the conclusions arrived at. Unfortunately, owing to the closing down of the smelting and refinery plant at these works, sone of the experiments could not be carried to a more definite and commercial basis, but they are given in the hope that they may be of interest to members, and may perhaps suggest further thought along the lines indicated.ROASTING AND SINTERINGThe greater part of the ore treated at these works came from the Central mine, Broken Hill, but, in addition, a large quantity was purchased from other parts of New South Wales and from Tasmania. This purchased ore was seldom received in the form of a concentrate, but initially in its crude state, and therefore had to be crushed. The crushing was done in a Krupp mill, and the ore then added to the roasting mixture. This addition of crude ore was one of the main...

Jan 1, 1923

By M-A Van Ende, N Kumar, I-H Jung

In order to utilise the powerful thermodynamic databases for process simulations, a concept called Effective Equilibrium Reaction Zone (EERZ) was introduced to couple thermodynamic database calculations and reaction kinetics. Using the EERZ concept, many process simulation models for steelmaking processes have been developed within the FactSage steelmaking consortium. After validation of the simulation results by comparing with plant data, the simulation models have been applied to improve plant operations. Several success stories of the improvement of real steelmaking operations are shared. A new user-friendly FactProSim software developed for building process simulations is introduced.

Aug 21, 2024

By T Hill, J Everingham, P Clark

Currently, social impact assessment (SIA) is used to determine social impacts across the life-of-mine (LOM) to closure. This paper draws on recently completed SIA reports from the Martha gold mine in Waihi and qualitative interviews in the community that explored post-closure options, to review the challenges mining companies face when engaging with iwi4 through the SIA process and what that may mean for closure planning. The Maori of New Zealand consistently lobby to have a distinct voice in resource management issues. This is in line with the evolution of indigenous participation in SIA globally and with New Zealand policies, not least of which, the Treaty of Waitangi (the founding document of New Zealand) makes provision for Maori self-determination with regard to natural resources. Land use for mining has been a source of conflict for Maori and mining can have profound cultural and social impacts on the Maori community, yet despite Treaty intentions their representation in SIA has been comparatively limited. With this in mind, the Waitangi Tribunal has released the Ko Aotearoa Tenei (Wai 262) report, which recommends far reaching reforms to laws and policies affecting Maori culture and identity including natural resource management. This landmark report seeks to move the Maori-Government relationship beyond grievance to partnership. Given suggested policy changes in Wai 262 and the risks of poorly conceived closure planning, it is timely to review where Maori currently fit into the SIA process. The findings of this research suggest that improvements to the outcomes of this process will require companies to act beyond compliance. However, these improvements may also ensure mining companies maintain their social license to operate and to ensure continued influence across the life of a project to closure.CITATION:Hill, H, Clark, P and Everingham, J, 2012. æThere is an emptiness for Maori here in WaihiÆ - Understanding indigenous perspectives on post-mine land uses in closure planning, in Proceedings Life-of-Mine 2012 , pp 153-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By D J. Williams, G W. Wilson, S, A B. Tran

A comprehensive field program was implemented to evaluate the internal structure and hydrology of two full-scale waste rock piles. The excavation of waste rock dumps for in-pit disposal at the two mine sites provided an opportunity to characterise the in situ properties of the dumps given contrasting geologic and climatic settings. The internal structure and materials within the dumps were observed and sampled as the waste rock piles were being excavated and placed in the open pits for permanent closure. The field program was designed to fully characterise the structure and material properties of the waste rock. The alteration of the material by physical and chemical weathering was also observed. Samples were analysed for paste pH, water content, grain size distribution and geochemistry. In situ density and matric suction were also measured. Soil water characteristic curves and saturated hydraulic conductivity were measured for representative materials. These properties were used to predict seepage pathways through the waste rock and the resulting outflow geochemistry using the finite element model SEEP/W. The materials in the dump at Site 1 were predominantly fine-grained in texture and highly weathered. The presence of dipping beds with alternating coarse and fine materials was evident throughout the profile of the dump. The structure of the waste rock appears to have an impact on the hydrologic pathways within the waste rock pile. The material in the dump at Site 2 was found to be competent and resistant to particle size breakdown. The particles range in size from clay size to large boulders with the median particle size being approximately 125 mm in diameter. The coarse-grained texture of the waste rock resulted in a loosely packed arrangement of coarse particles with little matrix material infilling the pore spaces between the coarse-grained particles. Seepage modelling for Site 1 was completed to predict seepage paths based on observed structure and hydraulic properties measured in the laboratory. The modelling showed that materials with a fine grain size distribution become the dominant pathways for flow through the waste rock pile. The modelling also showed that layers with high silt and sand contents are subject to the highest flow rates. Finer grained clay rich layers have a low hydraulic conductivity and do not convey large volumes of water. Alternately, coarse gravel and cobble materials are unsaturated under values of matric suction that approach the residual water content of the material and do not transmit liquid water. The seepage modelling together with the results of the geochemical analysis show that the dominant particle size that receives the most fluid flow and flushing ranges from fine sand to silt, corresponding to materials with air entry values ranging between 5 kPa to 50 kPa.

Jan 1, 2003

By E Nettleton, A Melkumyan

Identification of geology and mineralogy in situ on the mine face is essential if mining processes are to be automated for tasks such as exploration, grading and reconciliation. Hyperspectral data acquired from field based platforms are ideally suited to these tasks, and are set to revolutionise the automated mining industry. Changing conditions of solar illumination introduces variation into the hyperspectral signal, which is unrelated to geology, complicating analysis of data. Thus, algorithms must be able to deal with changing illumination conditions and operate in a consistent and probabilistic framework, which is a prerequisite for data fusion with other sensors. To produce accurate classification maps of geology, algorithms must be developed that are effective under different conditions of illumination.The efficacy of three algorithms to classify hyperspectral data for geology mapping on vertical mine faces was assessed. These algorithms are the spectral angle mapper (SAM), and two machine learning methods operating within a fully probabilistic Gaussian process (GP) framework û the squared exponential (SE) and the observation angle dependent (OAD) covariance functions (kernel). Two experiments were done to assess the classification performances. The first determined the performance of the algorithms by classifying hyperspectral data of known rock samples acquired using a field spectrometer. The GP-based methods had a similar performance, with average accuracies and F-scores of 97 and 88 per cent (GP-OAD) and 95 and 81 per cent (GP-SE), respectively. Average accuracies and F-scores for SAM were significantly smaller (80 and 40 per cent respectively). The algorithms were then applied to hyperspectral imagery acquired from a vertical mine face at different times of the day, under very different conditions of illumination. In contrast with experiment 1, SAM and GP-OAD gave results which were superior to GP-SE and were entirely consistent with geology mapped in the field. Compared with SAM, GP-OAD was less sensitive to the effects of shadow and produced classified images that were less noisy. The GP-SE method failed to delineate even gross changes in geology on the mine face. These results show conclusively that in order to use independent training data (spectral library) to classify imagery acquired under a different set of conditions, algorithms must take into account variability in incident illumination. Measures based on spectral distance are inferior to those based on spectral angle.The OAD kernel within the GP framework (GP-OAD) is superior to the other two methods because:it provides a probabilistic framework;it is insensitive to variability in illumination within and between imagery acquired under different conditions; andit can identify and map geological zones on a vertical mine face using an independent spectral library, without a priori knowledge.

Sep 26, 2011

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

By Seib W

In cut-and-break rock excavation use is made of the fact that breaking rock in tension towards a free face requires a specific energy of excavation which is small in comparison with that required for rock excavation using conventional tools operating by a process of indentation of the rock.The process of cut-and-break excavation comprises firstly a cutting step in which a groove is cut into the rock surface, followed by a breaking phase in which a tool is inserted into the cut in order to break the rock adjacent to the cut.

Jan 1, 1992

By N Tyson

Throughout Australia and the world, there have been in recent years a number of incidents involving the reaction of ammonium nitrate based explosives with ground containing certain types of sulphides. This paper presents a comprehensive strategy designed to identify, assess and mitigate the risks involved with blasting in areas of reactive ground. Undertaking blasting in reactive or potentially reactive ground involves a degree of risk, the level of which is dependent upon the controls in place for specific sites; this in turn depends upon the degree of sound reasoning and judgement behind the implementation of these controls. Implementation of controls to minimise the risk of incidents also involves a measurable increase in production and blasting costs. To achieve a balanced solution to this matter, decision-makers need to understand how the risks eventuate, how they should be evaluated, and how control measures reduce the risk. Also required is an understanding of how the problem affects the economics of the operation, and the magnitude of this effect. It is the aim of this paper to provide a structured approach to gaining this knowledge, so that mine management, the workforce and explosive suppliers may jointly develop more effective economic and safe blasting systems for potentially reactive ground. Using a combination of fault/event tree risk assessment and semi-quantitative analysis, a structured approach to dealing with the issue will be illustrated.

Jan 1, 2001

By S D. Dessureault

In one of North AmericaÆs largest mines, which contains more than six active coal-producing faces, mine controllers must meet the complex challenge of adhering to the mine plan while also ensuring customer quality. Fleet management systems (FMS) provide many different avenues to control production flows, from the faces to the various pit crushers. Nonetheless, mine controllers must balance a variety of factors such as unplanned downs, differing customer demands, their own daily key performance indicators (KPIs) related to equipment utilisation, among others. Deviating from the short-term mine plan is the most common means of balancing the other factors, since adherence to the plan is traditionally only measured during the weekly variance meeting with engineering staff. However, such deviation may be one of the most costly responses, as long-term scheduling issues may arise such as multi-face dead-heading or insufficient stripping. This paper focuses on the development of a system for real-time adherence to mine plan within a control room environment. This system is part of a larger blending-focused, multi-million dollar project with elements of a centralised remote control room, developed at the University of ArizonaÆs Mining Information Systems and Operations Management (MISOM) Mine Control Center (MC2). The mine plan (MPL) component of the overall blending system integrates both historical and real-time FMS data with mine plan requirements directly sourced from original systems (no additional input required). The measures, displayed largely as graphs, have tools to help controllers manage the production to facilitate adherence to the plan. Some measures are designed to motivate crews to perform by inciting competition between crews, softened through a study of the controller culture. The MPL component was deployed at the mine, and the before and after deployment adherence was measured. This paper discusses the technical development of the new tool, its deployment, and an ethnography (study of culture) to understand controller motivation.

Sep 26, 2011

By A Lechner, T Baumgartl, S Arnold, P Audet

When revegetation is a part of a rehabilitation strategy at mine sites in arid and semi-arid environments, its success can be strongly affected by the availability of water prior or during the time of seed dormancy, germination and early growth of seedlings. The semi-arid and arid environments of northern Australia are characterised by highly variable and erratic rainfall and hence the actual weather conditions at and around the time of germination and seedling emergence play a critical role in determining the success of plant establishment and the type of plant community that may develop.Using available climate data, an analysis has been undertaken and a set of indices has been developed which describe the suitability of the climatic conditions for rehabilitation. In total, eight sites from Queensland and one site from New South Wales, Australia have been analysed. It could be determined that regular rainfall and relatively short periods of water-deficit are key characteristics of climate suitability. A comparison of the locations studied allowed the separation into suitable and susceptible locations in terms of the availability of water, amount of rain and duration of drought between rain events.In our experience, specific estimates of climate suitability are rarely incorporated into the design of mined land rehabilitation programs. We consider that the regional intensity, seasonality and extremity of climate represent an overarching component of landscape complexity, which in turn will influence the development of post-disturbance ecosystems in these regions. This paper presents the outcome of climate analyses paired with the development of suitability indices. A conceptual framework is presented explaining the suitability matrix and its incorporation as a prognosis tool to achieve greater certainty for success in rehabilitation development.CITATION:Baumgartl, T, Arnold, S, Audet, P and Lechner, A, 2014. Development of climate-based suitability indices for the improvement of success in rehabilitation, in Proceedings Life-of-Mine 2014 , pp 483–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By M Hedley

Tracking plant and personnel in underground environments provides multiple potential benefits for a mine including increasing safety, better monitoring of production, traffic control, and in the future monitoring and control of autonomous vehicles. The main techniques for wireless tracking are to use radio frequency identification (RFID), signal strength based techniques, and time of arrival (TOA) based techniques. RFID does not provide continuous tracking and signal strength techniques have poor accuracy in the complex radio propagation environment present in mines. TOA based techniques are potentially the most accurate, but most current equipment does not realise the potential of the technique. CSIRO has been developing the wireless ad-hoc system for positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines. WASP has been licensed for sporting applications and has delivered encouraging results in early trials for a surface and an underground mining application. The system utilises a number of ‘anchor nodes’ that are placed at surveyed fixed locations within the mine, and tags attached to plant or personnel to be tracked. The system provides an ad hoc data communication network, thus wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging from 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of initial testing in an underground mine that shows that the system achieves high ranging accuracy, hence localisation accuracy.

Mar 21, 2011

By J Liu

In situ coal gasification is a method of extracting a high proportion of the energy value from coal without the need for mining. In situ conversion of coal to combustible gases is achieved by drilling wells into the seam, injecting gasification agents and initiating combustion. The product gases are then extracted to surface using production wells. These gases are clean energy sources for power generation, heating or synthetic fuel production. In situ coal gasification is of particular interest with respect to its lower environmental impact, potential application to otherwise inaccessible energy resources (ie offshore, deep deposits or beneath protected lands) and low capital intensity. Practical application of this clean technology is restricted primarily by lack of satisfactory quantitative descriptions of the processes involved, in particular the hydromechanical processes.In this study, three characteristic physical zones of an in situ gasifier are identified as the rubble zone, combustion front and virgin coal zone. Coupled mechanical processes of coal consumption and overburden collapse are used to describe the permeability profile in the rubble zone. Additionally, the redistribution of overburden load associated with coal consumption is accounted for with the formulation of a stress (compressive) dependent permeability profile, which is applied to the virgin coal zone. The model was implemented into and solved by FEMLAB, an advanced computer simulation tool. The flow process, according to DarcyÆs Law, is subsequently described in terms of permeability dependent injectivity. Injectivity is an indicator of flow velocity, which has been identified as a crucial factor in determining the commercial value of product gases from in situ coal gasification. The stress alteration to coal permeability was found to have a dominating influence on the flow process. This finding implies that a greater understanding of the in situ coal burning induced deformation of surrounding rocks would be of significant value in assessing the economic viability of applying this clean technology to potential sites.

Jan 1, 2004

By L Soebari, W Sunyoto

The Wabu Ridge Gold Skarn deposit is located at elevations of up to 3100 metres above sea level, in the Central Highlands of Irian Jaya, Indonesia, 35 km NNW of the Grasberg porphyry deposit. Wabu is a grass-roots discovery in an area with no previous gold mining history or record of gold mineralisation. A geological resource of 117.26 million tonnes at an average grade of 2.16 g/t Au (1.0 g/t Au cut-off) has been defined to-date. Mineralisation is hosted within a skarn occurring along the southern boundaries of the Late-Miocene age monzonite-diorite Pagane intrusive complex. The intrusive complex occurs in the footwall of a major EW structure, the Derewo fault, which displays sinistral strike-slip and reverse fault movement. The Derewo fault separates Derewo metamorphic units to the north from platform sediments of the Australian craton to the south. The skarn has a strike length of 6 km and is up to 1.5 km wide. It is developed within calcareous shelf sediments of the Tertiary New Guinea limestone group and is dominated by prograde garnet development. Gold mineralisation was deposited during retrograde alteration and is directly associated with arsenophyrite and bismuth minerals. Retrograde alteration is distinguished by a sequence of clinopyroxene , magnetite, epidote and hornblende, biotite and chlorite and lastly carbonate. Gold is associated with the biotite/ chlorite phase together with sulphides and precipitated as the result of fluid mixing. The Wabu Ridge Gold Skarn deposit was identified in April 1990 during a regional program of helicopter assisted stream sediment sampling of -80 mesh (180 microns) fraction and panned concentrate sampling. The initial discovery sample site was situated 15 km down stream from the deposit and returned 1.49 ppm Au for the stream sediment sample and 138 ppm Au for the panned concentrate sample. A regional airborne helicopter magnetics survey, conducted in early-1992, helped defined the main magnetite associated skarn zone and the extent of associated igneous rocks. Detailed follow-up commenced in May 1992 and consisted of detailed mapping, soil sampling and ground magnetics prior to drilling the first hole in October 1992. Drilling to-date has delineated a contained geologic resource of 8.1 million ounces of gold and potential exists for a larger resource.

Jan 1, 1999

By G Swayn, J Harpley

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluoride along with traces of cyanide. The disposal of SPL has been primarily in landfill because of difficulties in the development of a successful techno-economic SPL treatment process. Increasing concern about SPL landfilling practices is resulting in regulations in some countries to ban this form of disposal. As a consequence stock piling of SPL is occurring in an increasing number of countries pending the development of a successful treatment process. In 1992 Portland Aluminium investigated a SPL treatment process based on pyrometallurgical technology and approached a company called Ausmelt in Dandenong, Victoria, Australia, to ascertain if their submerged lance technology furnace process would be suitable to treat SPL. This approach resulted in Portland Aluminium, Alcoa and Ausmelt personnel working together on trials during 1992 - 1994 in Ausmelt's demonstration furnace to produce a slag and off gases containing hydrogen and sodium fluoride. The trials also evaluated the effect of oxygen enrichment to increase the concentration of hydrogen fluoride and the ability to recycle sodium fluoride particulate produced as the furnace off gases cooled. Other separate developmental work by Portland Aluminium, using CSIRO, resulted in the production of aluminium fluoride from the offgases from the pyrometallurgical process. The results of these projects influenced Portland Aluminium and Alcoa to authorise up to $A26 400 000 in December 1995 to construct a Research and Development processing facility to treat SPL at Portland. The Portland Aluminium unique gas treatment process converts hydrogen fluoride in the furnace offgases to aluminium fluoride in a multistage fluidised bed reactor, designed by Portland Aluminium. The aluminium fluoride produced in the reactor has been trialed successfully in Alcoa's aluminium smelting process as a replacement for imported aluminium fluoride. The installation in mid-2001 of a slag granulation system has enabled the production of a granulated vitreous slag having leachability qualities that conform to Victorian EPA criteria for the unrestricted use of the granulated vitreous slag from 'The Alcoa Portland SPL Process'. The unrestricted use of the granulated slag successfully completes 'The Alcoa Portland SPL Process' which treats the hazardous waste material SPL and converts it into non hazardous useful products.

Jan 1, 2002