Search Documents

By Raymond C. Boettner

The present work had for its purpose: 1) the identification of crack nucleation sites in AISI 4340, quenched to martensite and tempered over a range of 'temperatures; and 2) the comparison of fatigue processes in AISI 4340 with processes observed previously in pure metals From constant def1ection-bending fatigue tests, martensite boundaries were identified as the favored crack nucleation sites in quenched and tempered AISI 4340. It, also, was concluded that the fatigue processes operating- in this lous-alloy steel were similar to Processes observed in pure tnetals. ALTHOUGH much engineering data has been accumulated on the fatigue properties of quenched and tempered martensitic steels,' fatigue as a process is not as well understood in martensite as it is in pure metals.' Important features of the fatigue process, such as the identity of the nucleation sites, have not been determined in the commercially important high-strength low-alloy structural steels. The present work had for its purpose: 1) the identification of crack nucleation sites in a low-alloy steel, i.e., AISI 4340, which had been quenched to martensite and tempered over a range of temperatures; and 2) the comparison of fatigue processes in the AISI 4340 with processes observed previously in pure metals. This comparison of the fatigue processes in the different tempers was restricted to the high-strain low-cycle part of the S-N curve. Under these test conditions, previous work on a number of metals has shown that a large number of cracks are nucleated in less than 30 pct of the fatigue life.3 Furthermore, crack nucleation sites are not restricted to inclusions but are also associated with intrinsic structural characteristics of the metal. MATERIAL A 20-lb ingot of vacuum-melted AISI 4340 (for composition see Table I) was hot-rolled to 1-in.-diam rod and then cold-rolled to a 1-in.-wide strip, 0.08 in. thick. Fatigue specimens, see insert of Fig. 1, were machined from the strip with the long dimension parallel to the rolling direction. m this orientation, the stringers of 1 to 2 p inclusions present in the sheet lay parallel to the stress axis in the specimens. The specimens were austenitited at 2050°F in order to obtain a large prior austenite grain size, i.e., 2 mm, which facilitated the subsequent identification of the prior austenite boundaries. A helium atmosphere was used to minimize decarburization. After austenitiza-tion at 2050°F, the specimens were transferred to a 1450°F furnace so that specimen distortion was held to a minimum in the subsequent oil quench. Previous work4 indicated that refrigeration in liquid nitrogen prior to tempering reduced the percentage of retained austenite in the quenched specimens to less than 5 pct. Tempering was carried out in air over the temperature interval of 200°to 800°F to produce a range of mechanical properties, Table I. The preparation of the fatigue specimen was completed by grinding about 0.005 in. from each surface and electropolishing in a chrome trioxide-acetic acid solution for 30 min. Examination of etched cross sections of specimens prepared in this fashion showed the foregoing specimen preparation to be adequate for the removal of the decarburized layer present after the heat treatment. Transmission electron microscopy showed that the as-quenched microstructure of this alloy consisted of a mixture of martensite plates containing either a high density of dislocations or microtwins. Previous work5'6 indicated that in the course of oil quenching autotem-pering resulted in the formation of E carbide on the martensite and microtwin boundaries. Tempering for 2 hr at temperatures up to about 400°F resulted in further precipitation of the E carbide. Finally, at about 400°F, cementite began to replace the E carbide on the martensite and microtwin boundaries in addition to forming a Widmanstatten structure within the plate matrix. EXPERIMENTAL S-N curves were obtained using electropolished specimens cycled at 1800 cpm as cantilever beams in fully reversed bending at selected constant deflections. The deflections were translated into surface strains by means of a calibration curve obtained through the use of strain gages. An argon atmosphere was used to minimize environmental effects. To investigate the development of fatigue slip bands, the specimens of the different tempers were unidirec-tionally bent to a surface strain of 0.005 to 0.007, photographed to record the location and appearance of slip bands so introduced, and then cycled to failure

Jan 1, 1968

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970

By L. D. Mullins, W. R. Bartlett, R. H. Barham, W. L. Wahl

This paper describes an electrical model and its applicution to the analysis of four reservoirs in Saudi Arabia. The model has 2,501 mesh points and represents 35,000 sq miles of the Arab-D member. Details of modeling such as mesh size, control problems and standards of performance in matching reservoir history are discussed. The particular performance match achieved for the Arab-D rnember is presented. Details such as permeability barriers, aquifer depletion and iwerference between oil fields are given. The performance match realized in the Abqaiq pool is presented in detail. INTRODUCTION The resistor-capacitor network and associated control equipment described in this paper comprise an electrical analog of a reservoir system. Similar equipment has been used to study the transient response of reservoirs for many years. The unique feature of the model and application to be described is the extremely large size of the model and reservoir system, and the detail observed in simulating the reservoir with the model. The Arabian American Oil Co. first became interested in analog computers for simulation of oil reservoirs in 1949. Since that time, several models have been developed, each more elaborate and refined so that the reservoir system might be more closely simulated. The current model is the latest in a series designed, built and operated by the Field Research Laboratory of Socony Mobil Oil Co. in collaboration with Aramco. It has been and continues to be used to study the regional performance of the Arab-D member limestone reservoir. The Arab-D member is one of the Middle East's most prolific producing horizons.. THE MODEL The theory of simulating a reservoir system with an electrical system has been presented in the literature.1-5 Therefore, this paper will not discuss the theoretical aspect of the problem except to point out the correspondence between the fluid system and electrical system, as shown in Table 1. In general, the complete model is made up of input devices, output devices, central control and a resistance-capacitance (RC) network. At times, the RC network alone is referred to as the "model". However, it should be evident from the text which meaning is attached to the word "model". A discussion of the equipment follows. THE RESISTANCE-CAPACITANCE NETWORK The RC network consists of 2,501 capacitance decades interconnected through 4,900 resistance decades. The components are arranged to form a rectangular network of 2,501 mesh points in a 41- X 61-mesh array. Imposing the mesh grid system on the continuous reservoir system divides the reservoir into discrete areal segments. These discrete segments may be of various sizes. More precisely, the mesh size need not be uniform throughout the model. The RC network is fabricated in two sections which are connected at the top. An inside view of the "tunnel" formed by the two sections is shown in Fig. 1. The height and width of the tunnel are shown in the figure. Numerals appear along the bottom and along the back opening of the tunnel. These numbers denote the x and y co-ordinate positions of mesh points. Fig. 2 presents a rear view of one-half the model. The length dimensions of the model, as well as a rear view of the capacitor decades, are shown in this figure. The control dials used in adjusting the resistance and capacitance values on the model can be seen in the enlarged portion of the model shown in Fig. 3. The electrical capacity at any mesh point can range from 0 to 1.0 microfarads set to the nearest tenth of a microfarad. The electric resistance connecting any two mesh points can range from 0 to 9,990,000 ohms set to the nearest 1,000 ohms. External capacitors may be added to any or all mesh points if the need arises. The values of electrical resistance and capacitance are adjusted manually by manipulating the two types of decade units. INPUT EQUIPMENT A considerable quantity of equipment is used to control the input to the RC network. These input devices are

By Charles C. Fatino, Joel S. Hirschhorn

Loose compacts of strained and annealed stainless-steel powders were sintered at various temperatures and times to determine the effect of residual strains on the sintering behavior. The atomized powders were prepared by annealing, ball milling, and rean-nealing. The residual strains and domain size were determined by a Fourier analysis of X-ray diffvaction dala. The specimens were prepared by siwzultaneously sintering cylinders of both strained and unstrained powder. The evaluation of the sintered compacts included density measurements, metallographic examinations, and analyses of X- ray diffraction data. The results of these studies reveal a definite increase in sintered density and sintering rate for the strained powders. THE pressure compacting of metal powders causes deformation of the particles, mechanical interlocking, and increased contact area. After the deformation, severe residual strains remain in these particles. The subsequent contributions of these strains to the sintering process have been considered to be negligible, since the recovery and recrystallization temperatures usually occur prior to the temperature required for the sintering process. Sintering is con-sidered to be the process by which the powders are transformed into solid compacts at temperatures below their melting points. The sintering operation for stainless steel usually takes place in the range of 2050" to 2400°F (0.84 to 0.95 T,, where T, is the absolute melting point or liquidus temperature) while the temperature required for recovery is approximately 1800°F (0.75 T,). However, it has been shown for several metal powders that densification becomes significant in the range of 0.35 to 0.45 T,.' It is the purpose of this study to determine what effect residual strains have upon the sintering behavior of stainless-steel compacts. Loose compacts were selected for study in order to isolate the strain contributions and eliminate the variables inherent in sintering of pressure-formed compacts. Additional variables were minimized by using only one mesh size, one composition, one particle shape, and also by simultaneously sintering both types of powder. Very little work has been carried out previous to the present study to delineate the effect of strains on sintering behavior. Lenel et 01.2 observed that residual stresses in copper compacts caused shrinkage at comparatively low temperatures. Delisle3 loose-sintered ball-milled electrolytic iron and observed that bonding among particles began at a lower temperature as compared to the behavior of annealed powder. Increased densification of ball-milled oxide powders has also been noted.4'5 EXPERIMENTAL PROCEDURES Powder Preparation. The powder used for this study was a commercial-type 316L stainless steel made by the atomization process. A typical chemical analysis is: C- 0.025 pct Mo- 2.2 pct Cr-18.6 pct Ni-12.5 pct Fe—Balance The atomizing process is essentially the rapid freezing of liquid droplets. This nonequilibrium cooling causes coring to occur and two distinct phases are present within the solid particle, the austenitic phase and the ferritic phase. Due to the presence of this ferritic phase, the particles tended to fracture as well as become cold-worked during the subsequent ball-milling operation. (It was also found that this type of cooling produced a broadened and shifted

Jan 1, 1968

By Roy D. McLellan

Electrolytic production of cadmium at the Great Falls plant started in the first part of the year 1925. Prior to that time, an experimental unit had been in operation for a few months during the year 1922. At present the plant is the largest producer of cadmium, not only in the United States but in the world. Electrolytic cadmium is characterized by its very low content of impurities. The main impurities, which are lead, copper, zinc and iron, do not aggregate more than 0.05 per cent., leaving a cadmium content better than 99.95 per cent. The consumption of cadmium has increased rapidly since the war, with the growing use in the plating industry. Cadmium plating has come into prominence because of its connection with the automobile and radio industries. As a protective coating, a deposit of cadmium is superior to zinc. Cadmium is also used extensively in alloys. Important among these is the alloy with copper used in telephone and trolley wire. In proportion of 0.5 to 1.2 per cent., cadmium adds materially to the strength and wearing qualities. Practically all commercial zinc concentrates contain a small amount of cadmium. In the electrolytic zinc process, the cadmium that is dissolved in the regular leaching operation is removed from solution with metallic zinc, generally added in the form of zinc dust. This precipitate also contains the copper taken into solution and the excess of zinc dust, which is required in order to insure a complete removal of all impurities. The precipitate is treated by a separate process to recover the copper, cadmium and excess zinc. In order to make the metals more soluble and to render insoluble such impurities as iron, arsenic and antimony, the precipitate is roasted. The roasting is carried out in gas-fired McDougall furnaces, with a roasting temperature of about 700' C. The roasted residue is leached with dilute sulfuric acid, spent electrolyte from the zinc electrolyzing, containing 10 to 12 per cent. free H2S04. The leaching is done in cylindrical tanks of 30 tons capacity, agitated

Jan 1, 1930

By W. B. Braden

This paper presents a suitable method for predicting gas-free oil viscosities at temperatures up to 500F knowing only the API gravity of the oil at 60F and the viscosity of the oil measured at any relatively low temperature. The API pravity and the one viscosity value are used as parameters to determine the slope of a straight line on the ASTM slanaord viscosity-temperature chart. Then, knowing the slope of the line and one point on the line, the vrscosities at higher temperatures can be determined. The line slope correlations were developed at I00 and 210F since viscosity data are frequently measured at these temperatures. A procedure is given for predicting line slopes from measurements at other tetnperatures. A nomogram is furnished for solving the relationship. The correlation has been evaluated at temperatures up to 5OOF for oils varyzng in gravity from 10 to 33 " API. The correiution is applicable only to Newtonian fluids. Comparison at 500F of true viscosities and those predicted from values at 100F shows an average deviation of 3.0 per cent (maximum deviation of 6.0 per cent). Predictions from the values at 21 0F for the same oils how an average deviation of 1.5 per cent (maximum deviation of 3.4 per cent). INTRODUCTION Correlations have been developed by Beal' and by Chew and Connally' for predicting viscosities of gas-saturated oils at reservoir conditions. Each of these correlations requires a knowledge of the solution gas-oil ratio and the viscosity of the gas-free oil at the reservoir temperature. For temperatures below 350F, measurements of the gas-free oil viscosities can be made easily using commercially available equipment. In thermal recovery processes, however, reservoir temperatures well in excess of 350F are encountered. Viscosity measurements at such conditions are more difficult and time consuming and require modification of existing equipment or the construction of new equipment. Measurements are further complicated by the difficulty of handling highly viscous oils associated with thermal recovery processes. Therefore, it is desirable to have a correlation which allows accurate prediction of viscosities at high temperatures. A commonly used technique for predicting viscosities at high temperatures is to measure the viscosities at two lower temperatures, plot the values on ASTM standard viscosity-temperature charts and extrapolate to the temperatures desired. If either of the values is slightly in error, the extrapolated value can be significantly in error. To justify an extrapolation, three points are actually necessary. This procedure can consume much time, particularly with heavy oils. Considering the cost of viscosity measurements, it would be desirable to eliminate the need for direct measurements by having correlations which would allow viscosity predictions from other physical or chemical properties. Beal1 investigated the possibility of correlating viscosity with oil gravity at temperatures from 100 to 220F. While showing that a general relationship exists, he also found significant deviations. It is possible that correlations will be developed based on oil composition as more information becomes available. While not eliminating the need for viscosity rneasurements, the method presented herein requires that only one viscosity measurement be made. The API gravity must also be known. The theory is based on the fact that the viscosity of paraffins (high gravity) changes less with temperature than does the viscosity of naph-thenes or aromatics (low gravity). The gravity. therefore, is used as a parameter to determine the slope of a straight line on the ASTM standard viscosity-temperature charts. The correlation is applicable only to Newtonian oils, and deviations due to thermal decomposition and nonhomo-geneity cannot be predicted. Oils containing additives have not been evaluated. PROCEDURE Fifteen oils were used in developing the correlation; eight were crudes and seven were processed oils. Oil gravities varied from 9.9" API (naphthene base) to 32.7' API (paraffin base). The temperature range studied was 81 to 516F. Each oil used had a minimum of three viscosity measurements and each plotted essentially as a straight line on the ASTM charts. In all, 91 viscosity measurements were used in the correlation. Saybolt, rolling ball and capillary tube viscometers were used for the measurements. Viscosity data for Samples 1, 2, 4, 7, 10, 11 and 14 were obtained in Texaco, Inc. laboratories. The data for Samples 3, 5, 6, 8, 9, 12 and 15 were from Fortsch and Wilson,3 and data for Sample 13 were from Dean and Lane.' All data points used in the correlation are plotted in Fig. 1. It is seen that some of the viscosity values deviated slightly from the straight-line plots at the higher temperatures. Properties of the oils after exposure to the

Jan 1, 1967

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.' The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By Bernard G. Carbajal

The dielectric properties and thermal stability of glow-discharge polytnerized films of styrene, chloro-benzene, and other organics and photoresist filrns are presented. Variations in the glow-discharge polymerization procedure are related to thermal stability. Thermal treatwzents to improve the dielectric properties of both positive (A2 340) and negative (KMER) photoresists are given. THIS study of the dielectric properties of thin organic polymer films is part of a program to investigate the electronic applications of organic materials. Thin organic polymer films have been produced in an ac glow discharge,13 with a low-energy electron-beam process,4 and in an rf dicharge. A process has been developed during the course of this program for forming thin organic polymer films in a dc glow discharge. These glow-discharge polymerized (GDP) films exhibit some useful dielectric and insulative properties. Variations in the properties of the GDP films can be induced by changes in the source material (monomer) andor in the conditions of the glow discharge. Thin organic polymer films can also be produced from typical positive and negative photoresists. Some variations in the properties of the photoresist films can be induced by suitable post-application treatments such as thermal crosslinking. The properties of interest in this study are dielectric constant, dielectric strength, resistivity, and thermal stability. POLYMER FILM PREPARATION I) GDP Films. The GDP films were prepared in a dc glow discharge in an atmosphere of organic monomer vapor. The details of the glow-discharge procedure have been presented previously.6 Briefly, under the influence of a dc glow discharge organic vapors can be polymerized in the vapor phase and the resultant polymer (GDP film) deposits on and in the vicinity of the cathode. Substrates placed behind a screen cathode can be uniformly coated over all exposed areas. Pattern definition can be achieved using normal mask stencil techniques. Table I presents the pertinent parameters in the preparation of GDP styrene. Conditions of Forrrzation of GDP Styrene. The rate of deposition for GDP films was monitored using a current-time integrator. The thickness of the deposited film for a given set of experimental conditions was a function of the current-time integral. The fifth row in Table I is a compilation of the deposition rate of GDP styrene films. Other organic monomers behave in a similar fashion. With the exception of the highly halogenated saturated hydrocarbons, all organics subjected to the conditions of the glow discharge form GDP films. 11) Photoresist Films. Photoresists are normally recognized to exist in two forms, a low molecular weight, soluble polymer form (A) and a high molecular weight, crosslinked insoluble form (B). Typical negative photoresists are applied in the low molecular weight form A and converted to the high molecular weight form B by the action of light. (Positive photoresists are applied in form B and converted to form A by the action of light.) Eastman Kodak Metal Etch Resist (KMER) has been chosen as a typical negative photoresist. Polymer film samples were prepared in the same configuration used for GDP films. The KMER was applied in the usual fashion using a 120°C drying step (infrared-lamp heating) and a 180°C post-bake. Care must be taken to completely remove the solvent in the drying step and to properly develop and postbake to exposed photoresist. If the photoresist film is not properly dried and postbaked, severe blistering and peeling will occur during subsequent elevated-temperature exposure. Thickness can be controlled by varying the viscosity of the form A photoresist and the spin rate at application. AZ 340 was chosen as a typical positive photore-

Jan 1, 1967

By S. Vela, R. M. McKinley, L. A. Carlton

Johnson et al. have described a new well-testing technique that measures formation flow properties between wells.' The technique, called pulse-testing, requires a sequence of rate changes in the flow at one well and measzcrement of the re.rulting pressure changes at an adjacent well with a very sensitive differential pressure gauge. This paper describes an extensive application of the technique in a producing oil field. Pulse-tests on 28 of 45 possible well pairs in the field provided a picture of the areal distribution of reservoir hydraulic diffusivity, trans-missibility and storage. The primary objective in presenting these data is to demonstrate the potential of the methcid for reservoir description. A second objective is to show in three ways the qualitative and quantitative accuracy of reservoir parameters determined from pulse-tests: (I) pulse-test data show a nonuniformity in the field, closely correlating with the oil-water distribution as given by production data: (2) pulse-test values for permeability are comparable with core va1ue.s; and (3) perhaps most important, the field responds to a conventional interference test in the manner in which pulse-test data predict it should. The pulse-testing technique by Johnson et al.' is an ideal source of data for purposes of reservoir description, for it provides a measurement of formation storage S = +ch, hydraulic diffusivity 91 = k/+cp and transmissibility T — This paper describes an application of this method in a producing oil field. Results were analyzed to give numerical values for the parameters 7, T and S. These values were compared with oil-water production data (for the effect of fluid saturation), with core data and with data from an interference test. The reservoir in which the pulse-test survey was run is the result of a structural trap formed by a fault along the east side of a north-south trending anticline. A down-structure aquifer providcs a natural flank water drive for the pool. The producing formation is a dolomitic lime- stone having mainly vugular permeability; the formation oil has a gravity of 29" API with negligible dissolved gas. The field contains 19 wells, all on pump, arranged on 40-acre spacing along the top of the anticline. Fig. 1 shows the location of all these wells except two at the south end of the field. The dashed line on the right-hand side of the figure represents the approximate location of the fault with respect to well positions. Pulse-Test Survey and Analysis of Data A pulse-test requires a pulsing well and a responding well. In the field, changes were made in the rate of flow at the pulsing well by stopping and starting the pump periodically and measuring the corresponding pressure

Jan 1, 1969

By K. G. Davis

Dilute alloys of silzer in tilz haz been solidzjzed a1 controlled rules, in lzorizontal tubes 2 mrz and 0.5 rn in diam. Radioactive; tracer techniques we?-e used to study solute distvihutions along llze specimens and irmpurity substructures, as functions of the conditions growth. The results have heen mzalyzed using Burton, Prim, and Slichter's tnodel for the solute disty-ihution in the liquid ahead of an advancing solid-liquid interface. DECANTING techniques have been used to establish criteria for the formation of impurity substructure during solidification in several alloy systems An analysis equating the appearance of impurity substructure with the incidence of constitutional supercooling was developed,= in which diffusion was assumed to be the predominant mode of solute mixing in the liquid. Substitution of experimental data into the equations derived from the diffusion analysis gave reasonable values for solute diffusivity in the liquid. However, in these investigations solidification rates of 10 cm per hr and over were used, to minimize the effect of natural conection, whereas for crystals of high perfection lower solidification rates are needed, usually between 1 and 5 cm per hr. A knowledge of the conditions under which impurity substructures will be formed at low growth rates, and the degree of segregation to be expected, is therefore of interest. In the present investigation, radioactive-tracer techniques have been used to study the effect of growth rate, initial solute concentration, and size of specimen on the formation of substructure in uni- directionally solidified rods of dilute silver in tin alloys, over a range of growth rate between 0.5 and 10 cm per hr. Criteria for the formation of substructure were established by auto radiography. This was believed preferable to the decanting technique, for the relationship of the structure on a decanted interface with that of the freezing interface is not clear, since a layer of liquid is left on the surface following decanting.' The effect of substructure on the distribution of solute along the rods was also investigated. EXPERIMENTAL The procedure for sample preparation has been described in detail by einber. Alloys were prepared from tin of 99.999 pct purity and silver of 99.99 pct purity. A"', an emitter of both y and 0 radiation, was used as tracer. Samples of the alloys were drawn up into silica tubes with inside diameters 0.5 or 2 mm, remelted in a horizontal furnace, and solidified at controlled rates. A few centimeters of the samples were left unmelted for a measure of the initial concentration. Total sample length was approximately 20 cm. The temperature gradient in the furnace was kept constant at 36°C per cm in the region corresponding to the melting point for tin. To find how well this corresponded to the actual temperature gradient in the melt, a thermocouple of 38-gage wire was electrically insulated with a thin layer of Sauereisen cement and placed within one of the 2-mm-diam tubes, which was then filled with tin. The maximum diameter of the coated wire was 0.5 mm, the bead of the thermocouple junction being no larger than the diameter of the wire. A plot of temperature vs distance traveled by the furnace is given in Fig. 1 for a rate of furnace travel of 1 cm per hr. The temperature gradient in the liquid

Jan 1, 1967

By E. H. Lee, F. J. Fayers

Problems in reservoir analysis can usually he cupressed in terms of a system of nonlinear partial difjerential equations. A rnethod for .setting physically reasonable boundary conditions for these systerrls by ayplication of the theory of characteristics is discussed. A short description i.c. given of the technique for finding chnmcteristics of general first order and second orrler equations. Specific examples are quoted jrorn eqrrations occurring in theoretical reservoir studies. The princip1e. ossocicred wit11 the use of chnracteristic to set physically realistic boundary conditions me developed, and thr method is discussed in terms of boundary condition for the noncupillary, compressible, two-phase flow problen: jor the cupillary, ir~cowlpressible, two-phase flow problems for the tlrtergent flooding prohlenl; as for the compressible. noncapillary, two-phase flow pro11letn. INTRODUCTION In most problcms in reservoir analysis the physical situation is described by a system of nonlinear partial differential equations. The general solution to the set of equations usually comprises a wide range of functions ancl a particular solution is normally selectetl by applying suitable boundary conditions to the problem. In some cases it is clear from the physical situation what form the boundary conditions should take, but it is usually desirable to have an independent mathematical check of the suitability of the chosen conditions. From the mathematical standpoint, a system of partial differential equations with boundary conditions is said to be properly set if the combination determines a unique solution which is continuously dependent on the equation and the boundary conditions. Such a solution is sometimes termed "reasonable". In investigating the properties of the mathematical representation, it is useful to determine the structure of the system by the application of the theory of characteristics. This theory determines in the space of the independent variables, lines or surfaces which play a special role in thc system's behavior. The characteristics determine the possibility and nature of the propagation of discontinuities in the derivatives of the dependent variables. Along the characteristics certain differential relations hold which for some problems allow a so- lution to be obtained analytically. In the case of hyperbolic equations the characteristics can bc used as 3 basis for a numerical solution. If a complicated nonlinear system is to be solved, a study of behavior of the characteristics will indicate what boundary conditions should be chosen. By using the method of characteristics, several advances have rccently been made in solving reservoir engineering problems. Sheldon, Zondek and Cardwell' have discussed how the the method may be used grap-phically to solve the incompressible two-phase displaccmerit problem when the gravity term is included in the equations. Fayers and Perrine' have applied the method to study the equations representing detergent flooding. When compressibility and solution-gas effects are introduced into the two-phase flow problem, the equations and their characteristics become more complicated. It will be seen that in this problem the characteristics are useful for indicating a reasonable set of boundary conditions but cannot readily be used to compute a numerical solution. This problem has been solved on the IBM 701 using normal finite difference methods hy West, Garvin and Sheldon." The material to be prcscntcd in this report is divided into three sections. The first discusses the determination of the characteristics of first and second order partial differential equations; the second describes the selection of suitable boundary conditions by the application of the principle that the future cannot affect the past; the third discusses the use of characteristics for setting the boundary conditions of the two-phase solution-gas flow problem. A useful introduction to the method of characteristics has been given by Hildebrand.' A summary of the method will be given in this section of the paper. The First Order Equation The quasi-linear equation of first order is It is linear in the partial derivations of z. The properly linear equation has the form The characteristics of are curves along which the

By Paul L. Horrer

Costly damage by severe wave attack to many engineering structures has illustrated the need for a consideration of the nature of wave action in plans for offshore drilling operations. Using wave data it is possible to answer questions pertaining to engineering problems such as platform elevation, structure orientation, and expected wave forces. For locations where wave records are not available a technique can be used to obtain information about wave characteristics from past meteorological data and near shore submarine topography. Forces exerted on structures by waves may be divided into four parts. A completed study is given in which frequencies of various wave heights and maximum frictional drag forces are computed for a typical offshore drilling site. INTRODUCTION Waves of tremendous proportions accompanying hurricane winds crash against breakwaters and other offshore structures causing untold damages. Wave forces exerted on structures at these times are enormous, as shown by past records of incidents where massive portions of breakwaters have been broken off and moved by waves. On other similar occasions, whole structure; have been unloosed and smashed or floated away. These incidents, which seem almost incredible, serve to illustrate the great amount of energy contained in large waves, and to show that this energy results in powerful forces destructive to offshore installation~ which are not designed sufficiently strong to withstand wave attack. In the past the expected frequencies of waves having various characteristic.% have rarely been considered in the design of structure affected by wave action. As a result, many structures have failed to accomplish the purpose for which they were designed or have collapsed under wave attack. Others have been constructed to withstand greater wave energy than is ever encountered, with resulting waste of material and construction time. In this study an analysis is made of the frequencies of waves having different characteristics which affect the plans for offshore drilling installations. After such an analysis the erection of these structures can proceed with less risk involved and with more efficiency and economy. ENGINEERING ASPECTS In the offshore drilling program wave forces play an extremely important part in design and construction of drilling rigs in shallow water. The design of a platform or other structure from which drilling equipment is operated is critical, becauze any damage to the platform may endanger personnel and result in complete loss of equipment. Since a platform built too close to the water would be battered by breakers, and one built unnecessarily high would involve undue expense, it is necessary to know the most desirable elevation at which the platform should be erected. This is only one of many questions about structural planning which can be answered using existing technique for determining wave characteristics. The purpose of efficient design for the portions of many types of offshore structures which are acted upon by wave forces is the same as that of all designs which deal with frictional forces of a fluid on a solid. For these structures the problem is comparable to that encountered by undersea craft moving through water, except that in the case of a fixed structure the force is produced by the water moving past the model. For off shore sructures which are extremely rigid the frictional forces may be nearly negligible compared with the impact or shock forces imparted by breaking waves. In all case; the better design is that which offers the least resistance to the opposing forces. From a consideration of wave forces, each drilling structure varies in efficiency depending upon the type and amount of superstructure in contact with the waves. For example, round piling and bracing offer less resistance to wave forces than do I-shaped ones. All network superstructure such as cross bracing should be kept to a minimum and at as low an elevation as possible, so that it will not expecience the pressure exerted at the tops of breaking waves. Models of proposed structures can be tested in wave tanks and in the field to ascertain the efficiency of specific designs. Past experience in beach and shoreline engineering has shown that, although changes in the topography of the bottom very near shore do not seem to be occurring, the natural forces involved may be in a delicate balance such that a static state exists. Interruptions of any of these natural forces by erecting offshore structures are likely to cause undesirable effects. Changes in beach profile result partly from sediment being brought into suspension by the orbital motion of waves and partly from the transport of sediment by longshore currents. With the erection of an offshore structure and consequent change in the combined effects of these two forces, unfavorable deposition upon, or erosion of, the bottom at the site may occur. Therefore, combination wave and current studies are essential for the solution of problems involved in the design of most marine structures. TECHNIQUE FOR OBTAINING WAVE INFORMATION In determining the probable effect of wave action on an offshore drilling structure, it is first necessary to know the usual frequencies of certain wave types for the given location. A technique has been developed which provides a means for obtaining information about wave characteristics in the

Jan 1, 1949

By Henry A. Wriedt, John Chipman

Equilibrium in the reaction of hydrogen gas with oxygen in liquid nickel, iron, and their alloys has been studied at temperatures of 1500° to 1700°C. The equilibrium con^stant, 0/p, [% O], is greater in nickel then in iron by a factor of 45 at 1594 C. In the alloy steel range, the activity coefficient of oxygen is slightly increased by the presence of nickel. NICKEL is more resistant to oxidation than is iron, in both the solid and the liquid state. The solubility of oxygen,' however, is greater in nickel than in iron. The two metals and their liquid alloys constitute an interesting series of solvents in which the chemical behavior of oxygen can be studied by methods similar to those used for liquid iron.' Experimental Method The furnace assembly, including the tube for preheating the entrant gas, was the same as that described by Gokcen and Chipman. " controlled mixture of water vapor, hydrogen, and argon preheated to approximately the melt temperature impinged upon the surface of the liquid metal. The charge, weighing about 35 g, was held in an alumina crucible at constant temperature in the gas stream for a prolonged period, then quenched in a stream of cold helium, sampled, and analyzed for oxygen by the vacuum fusion method. The temperature of the liquid metal was measured by a Leeds and Northrup optical pyrometer which had been checked against a similar instrument certified by the National Bureau of Standards. The freezing point of electrolytic iron in hydrogen, taken as 153j°C, was used for frequent checks. This point and the emissivity determined by Dastur and Gokcen" established the transmissivity of the optical system. The emissivities of Fe-Ni alloys at 1535" are known from the experiments of Smith and Chipman,h nd it was assumed that the variation with temperature is parallel with that of iron. Recorded temperatures are probably accurate within k5"C. Preparation of Gas Mixtures—Since the ratio H,O:H, had to be much higher for nickel than for iron, it was found convenient to construct two separate systems for gas preparation. In both cases, the ratio of argon to the sum of the other two gases was at least 4, the proportion of hydrogen and water vapor being varied to produce H,O:H, ratios from 0.2 to 70. The primary purpose of the argon was to diminish the errors caused by thermal separation' in the gas phase. In addition, its presence lowered the saturation temperature required for a given H,O:H, ratio and minimized the difficulty of preventing condensation. Both systems were modifications of the one used by Dastur and Chipman.' For H,O:HI ratios greater than 2, welding-grade argon purified by passage over magnesium chips at 620°C was mixed with hydrogen produced in the electrolytic cell shown in Fig. 1. The design was based on a cell used by Bodenstein and Pohl," the important features of which area nickel wire cathode and sodium hydroxide solution as the electrolyte. The rate of hydrogen evolution was controlled by a calibrated ammeter and a rheostat in the circuit, the current efficiency being taken as 100 pct. Precise control of the argon flow rate at about 300 ml per min was achieved by means of a capillary flowmeter having a controlled pressure drop. The molar flow rate was measured volumetrically before each run, and a constant flowmeter setting was maintained thereafter. The A-H, mixture passed through a water saturator of the type previously described," the saturation temperature being maintained automatically with a fluctuation of k0.04"C. The tube between saturator and furnace was heated by a resistance winding. The system was of all Pyrex construction with the exception of the stainless steel tube containing magnesium chips. This was connected with the glass tubing at the upstream end by

Jan 1, 1957

By Michael P. Robinson

It has been suggested that streaming potentials are not nomlally logged because the streaming potentials known to be generated across mud filter cakes are substantially cancelled by streaming potentials generated in contiguous shale beds. Laboratory measuments of streaming poterztials acrons hand specirnens of shale have been adduced as evidence to support the suggestion. The experiments show that streanzing potential depends on the resistivity of the equilibrating solution and on pressure drop. Meizsurenlents were made perpendicular to the bedding planes of the shales. The mechanism of streaming potential generation in shale which the suggested cancellation theory iniplies has been critically examined. Conclusions reached are tested by comparing self potentials logged before and immediately after changing the resistil~ity (but not the weight) of mud in a borehole. The resultant SP change is found to equal the theoretical electrochetnical potential change, i.e., cancellation of .strearning potential is independent of mud resistivity. Since streaming po/entials generateal across mud filter cakes depend critically upon mud reistivity, shale .strearlling potential in situ must he equally sensitive. Using plausible values for the pemleahility, porosiy arzd compressibility of shale, the van Ererdingerl-Hurst approach shows that the pressure drop between horehole pressure and formation pressure in a radially honzogeneous shale is unlikely to coincide with the zone of filtrate invasion. If, perchance. this coincidence occurs with one mud a chatzge 10 a second must result in non-coincidence, i.e., a .YP logged in the second mud should show a streaming potenlial. The dilernrna may he overcome by postrrlating: (I) perrneabilities of shale7 parallel to their beddine planes greatly exceed their cross-bedding permeabilities; (2) a resistivity-sensitive mud cake of low permeability forms either on the face of, or probnhly in the lanlinations of, many shales. These postulates are examined with reference to the pres.sure and SP histories of the McClosky and Aux Vases zones in the Illinois Basin and some srcpport for them found. It is concluded that a definitive solultion to the streaming potential problem does not exist. INTRODUCTION Recently Gondouin and Scala' published a contribution to the streaming potential problem which is notable particularly for the elegance of its experimental techniques. The conclusions drawn by Gondouin and Scala from their studies amplified those previously suggested by Schehck'. In essence they suggested that the streaming potentials known to develop across mud filter cakes" are not normally observed on SP logs because they are largely cancelled by streaming potentials generated in adjacent shales. This suggestion appears so reasonable that many workers in the logging field will be prone to accept it. We incline strongly to the view that the suggestion is basically correct. Nevertheless, it is important to realize that the cancellation hypothesis in the form put forward by Gondouin and Scala does not appear to meet all the known experimental facts. It is the principal intention of this note to call attention to what appears to be a flaw in the relevancy of the experimental evidence adduced by Gondouin and Scala and to suggest an alternative hypothesis to remove it. The consequences of the new hypothesis are compared with field data which, we believe, are unique. A second but not less important purpose of this note is to emphasize that even the new hypothesis does not fully explain all field observations. Hence we conclude that further study of the streaming potential problem is required before it can be said that a definitive solution to it has been attained. The bare experimental bones of laboratory data on streaming potentials appear to be as follows. 1. A streaming potential is developed across a mud filter cake. This streaming potential is virtually independent of cake thickness but depends on the mud resistivity. The relationship is of the form, 2. A streaming potential is developed across a shale. This potential is independent of shale thickness but depends on the resistivity of the permeating solution if the shale has been first equilibrated in this solution. The relationship is of the form, The relationship in (1) was determined first by Wyllie3, confirmed by Gondouin and Scala and qualita-

By G. Borelius

ABOUT the turn of the century, Gibbs' thermo-dynamic theory of heterogeneous equilibrium, on the one hand, and the experimental methods of thermal and microscopic analysis, on the other, gave to the physical metallurgist his first scientific tool, the equilibrium diagram. The classical equilibrium diagram of a binary alloy system shows the boundaries between ranges of homogeneous and heterogeneous equilibrium in their dependence of concentration and temperature. A homogeneous solid sohtion which on cooling passes such a boundary is assumed to precipitate, forming a mixture of two phases with different concentrations. The equilibriunl diagram and the equilibrium theory, however, give no information about the time scheme of the process or the intermediate states passed during precipitation. For this reason it satisfies neither the practical need of the metallurgist nor the curiosity of the physicist. As a matter of fact, in the heat treatment of alloys for technical use the objective very seldom is the equilibrium state. Thus good mechanical properties of construction material are connected, for the most part, with some intermediate state. As these intermediate states are thermodynamically unstable, there is, from a theoretical point of view, always to be expected a decay of the good properties with time; and it is a matter also of practical interest to know whether this natural life time of a material is of the order of, say, ten or thousands of years. Thus, for many reasons, there is a current demand to complete our knowledge of equilibrium through knowledge of the kinetics of the precipitation phenomena. From the point of view of the physicist, the most interesting question in this case is whether there are any general laws governing the kinetics. According to a generally accepted view, precipitation is ruled by two more or less independent phenomena, the formation of nuclei of a new phase and the growth of these nuclei. It is also commonly accepted that there is a tendency for the velocity of growth to increase with increasing temperature because of the increasing mobility of the atoms. There is also a tendency for the velocity of growth to decrease in the neighborhood of the two-phase boundaries. So far, however, very little is known quantitatively about this fundamental phenomenon in the case of solid metallic systems. In our laboratory attention has been directed especially toward the nucleation phenomena, and a series of measurements have been carried out with the guidance of a work- ing hypothesis (based on experiences from previous work on order-disorder transformations in alloys) about the influence on the nucleation of thermo-dynamic potential barriers. However, before discussing the experiments, the theoretical ideas will be considered. In a binary solid solution the arrangement of atoms on the lattice points approaches with increasing temperature a state of full randomness, as illustrated by the ball model of Fig. 1, that might represent a [111] plane of a face-centered alloy with 30 pct "black" and 70 pct "white" atoms. In reality the atoms are changing places continually with their neighbors so that the picture should rightly have been a moving one. On account of this thermal motion the concentration of black atoms within a certain group of, say, a hundred or a thousand lattice points fluctuates with time around the bulk concentration of 30 pct in a manner governed by statistical laws. With decreasing temperature two independent changes in this state grow more and more important. First, the mobility of the atoms decreases, and second, the forces between the atoms will have an increased influence on the fluctuations. In alloys with a tendency for precipitation, which are the concern of this lecture, the distribution function of concentration fluctuations will broaden, so that the relative probability of great local variations from the bulk concentration increases. Fig. 2 gives an example of such a fluctuation. When the alloy is supercooled below the solubility limit into the range of two-phase equilibrium, the fluctuations will now and then at some point give rise to a state that resembles the equilibrium state and thus will form a stable nucleus that is capable of growing by diffusion processes. In discussions with colleagues and in the literature, I have often encountered the idea that three or four atoms of the dissolved metal could form a nucleus of the new phase. A look at the ball model might be enough to indicate that this cannot be true. If it were true, there should be nothing but nuclei, whereas we know from experiment that nucleation must be a rather rare occurrence. In fact we have, as will be mentioned later, certain reasons to believe that the nuclei are formed by fluctuations containing some hundreds of atoms, which should be the order of the number of black balls in the fluctuating group of the figure, if it were extended into three dimensions. As a working hypothesis we have assumed that the fluctuations producing nuclei, though large and rare, still are ruled by the distribution laws of fluctuations of the supercooled solid solution in its initial state. Thus the probability of nucleation will be connected to the thermodynamic properties of the solid

Jan 1, 1952

By M. E. Fine, A. A. Hendrickson

The critical resolved shear stress and the strain rate dependence of the .flow stress are reported for Ag base A1 single crystals up to 6 at. pct A1 over a temperature ralzge of 4.1° to 470°K. At room temperature the solid solution strengthening is attributed brinciballv to an increase in the dislocation density on alloying. At 42°K the alloys are relatively stronger because the dislocations widen on alloying and are more difficult to cut. In a previous paper, the authors reported the characteristics of strain aging in Ag base A1 alloys.' The variation of the magnitude of the strain-aging yield drops on aging time, aluminum content, and testing temperature strongly indicated that the phenomenon is due to the Suzuki mechanism. In the present paper, the critical resolved shear stress (CRSS) and the strain rate dependence of the flow stress are reported for Ag base A1 single crystals as functions of testing temperature (4.2" to 470") and A1 content (0 to 6 at. pct). Observations on the substructure and measurements of the effect of crystal growth rate are also given. The experimental re- sults appear explainable considering that aluminum additions increase the dislocation density and dislocation width. EXPERIMENTAL METHOD The methods of specimen preparation and tensile testing were described previously.' Briefly, single crystals were grown from the melt in a vacuum (1 x lom5 mm Hg), shaped into tensile samples by a combination of abrading and acid etching, annealed at 850°C in a vacuum (1 x 10" mm &Z) for several days, and furnace cooled to 200'. The testing was done on a model TM Instron using friction grips and a strain rate of about 5 x 106 per sec unless otherwise noted. The various testing temperatures were obtained by immersing the specimens in the following media: 1) 4.2': liquid helium using the apparatus of G. Byrne;' 2) 77°K: liquid nitrogen; 3) 200"K: dry ice and acetone; 4) 415' K: ethylene glycol; 5) 460' \ to 480' : molten Stanalax. In the determination of the CRSS above 296' K, a ratio method was used; the crystals were strained initially at the higher temperature, 0.1 pct shear strain, and then tested at 296' . The ratio of the flow stress between the two temperatures was then multiplied by the average CRSS at 296' K to obtain the value of the CRSS at the high temperature. (The test at 296' showed a yield point resulting from strain aging; the flow stress at 296' K was taken as the lower yield stress.) The ratio method, we believe, is more accurate than using different crystals since

Jan 1, 1962

By Albert E. Reed

The development of the modern highspeed vibrating screen, together with the increasing availability of long-lasting stainless-steel screen cloth for relatively fine-mesh separations, means that more screen circuits will be used in the future. It seems pertinent therefore to examine a few characteristics of screen-circuit products, and especially the points of difference as compared with products of classifier circuits. The most noticeable change that takes place when substituting screening for classification in a grinding circuit is a substantial drop in the circulating load, owing to the greater ease with which the "fines" leave the circuit. Where circulating loads of 500 to 600 per cent are considered fairly normal in classifier grinding circuits, the grinding circuit equipped with screens for equivalent work will have a circulating load of only 20 to 75 per cent. As a result, the products of screen circuits will show a minimum of overgrinding or sliming as compared with a classifier circuit. The desirability of this characteristic will naturally vary according to the metallurgical requirement in each case. Because screen separations make a sharper division according to particle size, the products of screen circuits can be expected to show greater crowding of particles near the point of separation. These changes in product characteristics are so important that other factors, both in the grinding and concentration processes must be adjusted if the operator is to take full advantage of the increased tonnages and higher efficiencies available to him through the use of the screen circuit. One factor that too often is overlooked when changing to screen circuits is the importance of adjusting the ball-mill or rod-mill charge, to compensate for: (I) increased tonnage of new feed, (2) decreased circulating load, or (3) more granular character of feed. These same factors should also be taken into consideration for their effect on the various types of concentration or flotation equipment that may follow the screen circuit. Over a period of years, this equipment has generally been designed and adjusted to the product of the classifier, therefore it seems obvious that some research on the adjustment and adaptation of concentrating and flotation equipment to screen-circuit products will be most profitable to the operators. To illustrate the points mentioned above, the results from three recent installations follow, with data on the comparative characteristics of screen and classifier circuits. A range of separation from 10 to 48 mesh has been chosen, using two general types of screening equipment and two types of classifiers. The first of the installations of which the results are to be examined is that of an iron-ore installation where eastern magnetite was being concentrated prior to sintering. Fig. I shows the original grinding circuit, using classification, while Fig. 2 shows the same circuit equipped with a

Jan 1, 1947

By Terkel Rosenqvist

THE desulphurization of molten iron and steel is a very complicated process. One way to arrive at a better understanding of this process is to break it down into several simpler chemical processes that can be studied individually in the laboratory. For a study of the different factors that influence the equilibrium distribution of sulphur between liquid metals and slags, several simpler equilibria may be investigated. One very important subject is the determination of the escaping tendency of sulphur in the liquid metal and its dependency on temperature and composition of the melt. Several papers in this field have recently been published.', ' Another subject is the study of the sulphur capacity of the slag. A molten slag is indeed complex, and even if sulphur distribution data for a large variety of molten slags may give empirical data about their desulphurizing power, the importance of the individual components is still not quite clear. It is accepted generally that lime is the most important desulphurizing component in the slag. The present investigation has as its purpose to study the desulphurizing power of lime in its standard state, and to provide a basis for thermodynamic calculations of the desulphurizing power of various lime-containing slags. The standard state of lime at steelmaking temperatures is solid calcium oxide, CaO. It can react with sulphur to form solid calcium sulphide, CaS. The relative stability of calcium oxide and calcium sulphide is expressed by the free energy of the reaction: 2Ca0 (s) + S1 (g) = 2CaS (s) + O2 (g) The existing free energy data for this reaction, listed by Kelley5 nd Osborn,' are uncertain to about 10 kcal and are of limited value for a calculation of equilibrium constants. Under the conditions prevailing in a melting furnace, the sulphur pressure may be expressed conveniently by the ratio H,S/H2 and the oxygen pressure by the ratio H,O/H, (or CO,/CO). The desulphurizing power of calcium oxide may, therefore, be studied by the reaction CaO + HIS = CaS + H2O. A study of this reaction may be complicated by certain side reactions: Water vapor and hydrogen sulphide may react. to form sulphur dioxide, and calcium sulphide may be oxidized to calcium sulphate. A thermodynamic calculation shows that these side reactions will be suppressed to insignificance if the equilibrium is studied in the presence of an excess of hydrogen. The apparatus used is shown in Fig. 1. About 10 g calcium oxide and 20 g calcium sulphide (laboratory qualities) were intimately mixed, and some water was added to make a thick paste. The paste was put into a thimble of zirconium silicate, which was placed within the constant temperature zone of a furnace, and capillary refractory tubes were attached in both ends. After the mixture had been heated in dry hydrogen at 1000°C for several hours all Ca(OH), and CaCO, had decomposed and CaSO, was reduced, so only CaO and CaS remained in the thimble forming a porous plug. The mixture was examined by X-ray diffraction after the initial reduction in dry hydrogen as well as after the subsequent experimental runs up to 1425 °C. It was shown that crystalline calcium oxide and calcium sulphide were always present together in about equal amounts. The unit cell edges were found to be 4.80A for CaO and 5.68A for CaS in good agreement with existing literature values." This shows that the mutual solid solubility is very small, and that the compounds are present in their standard states. Purified hydrogen was passed through water sat-urators kept at constant temperature in a thermostat bath. The amount of water vapor saturation was checked by means of a dew point method, not shown on Fig. 1. The gas mixture was passed through the capillary inlet into the furnace, where it was sifted through the porous plug of calcium oxide and calcium sulphide. The hydrogen sulphide present in the outgoing gas was absorbed in a zinc acetate solution and the hydrogen was collected over water. When one liter of hydrogen had been collected, the amount of hydrogen sulphide was determined by iodometric titration. As one molecule of H,O is used for the formation of each molecule of H,S, the equilibrium ratio H,S/H,O would be , where (H,O) is the molar concentration in the ingoing gas, and (H,S) the molar concentration in the outgoing gas. In the present work (H,S) was always very small compared to (H20). In order for the observed H,S/H20 ratio to represent the true equilibrium ratio the gas flow has to be: 1—Sufficiently slow to give a complete establishment of equilibrium, and 2—sufficiently fast to counteract thermal diffusion. Incomplete reaction would give a value decreasing with increasing flow rate, and thermal diffusion would give a value increasing with decreasing flow rate. When inlet and outlet tubes of about 2 sq mm cross-section were used, the observed gas ratio was independent of the flow rate between 15 and 125 cc per min, Fig. 2. In this range, therefore, the observed gas ratio represents true equilibrium.* For the rest of the in-

Jan 1, 1952

By J. J. Frawley, W. J. Childs

Experiments were carried out to induce grain refinement during solidification by applying vibrational energy (freq 20 kc) to small specimens of bismuth, tin, and bismuth-tin alloys. The results show that if the intensity of the applied sound -field is not great enough to fragment the growing dendrites of a pure metal, no grain refinement is observed and the pain size of the dynamically nucleated specimens is the same as the grain size of a specimen statically supercooled the same amount. Bismuth specimens did not show any grain refinement; whereas, the tin specimens did show grain refinement. This phenomenon is the result of the difference in growth habit between the bismuth and tin dendrites. The bismuth-tin alloys showed grain refinement and, in addition, the segregation pattern was changed. THE solidification process is a change in phase requiring the nucleation of the solid phase from the liquid and the growth of this solid phase at the expense of the liquid phase. Since many physical properties and also the integrity of a casting are dependent on the solidification process, understanding and controlling this process are very important.' A good example in the controlling of a cast structure using heterogeneous nucleation theory is the reduction of grain size in aluminum castings by nucleation catalysis.2 This mechanism of nucleation catalysis has been explained by Turnbull.3 Another technique for grain refinement, which has received much attention but the mechanism has not been fully understood, is to vibrate the solidifying melt. Vibrations can be applied to the melt either by vibrating the mold directly or by introducing a vibrating rod into the melt.4-13 Three mechanisms have been proposed to explain this phenomenon: 1) The mechanical fragmentation of the original dendrites that grew into the melt. These crystals or fragmented dendrites act as new growth sites. 2) The nucleation of new grains in the liquid by the generation of very high pressure pulses caused by cavitation in the liquid. 3) The remelting of the dendrite arms during the solidification process. This mechanism is operative only in alloy systems and would be enhanced by stirring or mechanical vibration. The purpose of this investigation was to determine the mechanism that will increase the number of grains when mechanical energy is introduced into a solidifying melt. APPARATUS The unit used to generate the ultrasonic vibrations was manufactured by the Redford Co., and is similar to the one used in ultrasonic soldering. Fig. 1 is a sketch of the major components used for generating ultrasonic vibrations. The crystal transducer assembly consisted of four lead zirconate ti-tanate piezoelectric crystals in an aluminum holder. An acoustical horn, which was fabricated from stainless steel, was attached to the holder by a set screw. The resonant frequency of this unit was 20,000 cycles per sec. A Pyrex crucible, 4 in. in diam and 4 in. high, was contained in a hole in the top of the horn. The piezoelectric crystals changed volume when excited by an electric signal, thereby generating a sound signal which passed through the horn. The crucible was coupled to the horn by a liquid silicone oil. The purpose of the couplant was to transmit the soundwaves from the horn to the crucible. Without the couplant, much of the sound energy would be lost. The energy transmitted was sufficient at the resonant frequency used, so that acoustical cavitation always occurred in the molten metal. The presence of acoustical cavitation was detected by the characteristic hissing sound emitted from the liquid. EXPERIMENTAL PROCEDURE The influence of ultrasonic vibration on the grain refinement of bismuth, tin, and bismuth-tin alloys was studied. These metals were chosen because of their low melting temperature and the relative ease with which they can be thermally supercooled. The following procedure was used for obtaining large amounts of supercooling. Pure bismuth (99.999+), which was received in bar form, was mechanically broken into pieces small enough to be accommodated in a 50 ml beaker. About 200 to 300 g of bismuth and a few grams of SnCl2 as a flux were placed in the 50 ml beaker and melted by induction heating. The melt was held for 20 min at

Jan 1, 1970

By F. Keller, J. D. Edwards

The anodic treatment of aluminum presents problems of scientific as well as of commercial interest.l-3 Of particular interest is the fact that, during the anodic oxidation process, the oxide continues to form at the metal-oxide interface under any oxide previously formed. This has led to speculation as to the mechanism involved in the formation of the relatively thick oxide coatings that are used commercially for decorative or protective purposes. Furthermore, the ability of certain types of oxide coatings to adsorb dyes and other substances has stimulated research to determine the actual structure of these adsorptive coatings. It has been found that anodic oxide coatings on aluminum are composed essentially of aluminum oxide. They are formed by the action of oxygen ions penetrating to the metal surface during the electrolytic oxidation treatment. These coatings can be formed in a number of different electrolytes, as for example, those which contain sulphuric acid, chromic acid, oxalic acid, or boric acid. These are the commonest and most useful electrolytes employed commercially. Except for certain specific conditions of formation, the coatings in general have been found to be amorphous alumina, as far as can be determined by X-ray or electron-diffraction methods. Anodic oxidation processes can be arranged in three rather general classes if they are grouped in relation to the solvent action of the electrolyte on the coating.4 In the first class, the electrolyte has little or no solvent action on the coating that is formed. In general, coatings produced under such circumstances are nonporous and non-adsorptive. In the second class, the electrolyte exerts an appreciable solvent action on the coating. These coatings are porous and adsorptive. Finally, for the third class, the electrolyte tends to dissolve the coating about as rapidly as it is formed. This action produces electrolytic brightening or anodic polishing of the aluminum surface and at most leaves only a very thin film of oxide. The nonporous and nonadsorptive type of oxide film is represented by the coatings that are formed when solutions of boric acid are employed as the electrolyte. It is especially significant that these impervious films are formed in electrolytes that exert little or no solvent action on the coating. Where a boric acid electrolyte is used, the coating tends to form rapidly, with the result that the flow of current is soon reduced to substantially zero. This indicates that the growth of the coating has stopped. As a rule, the thickness of the coating is roughly proportional to the voltage employed for formation and the coatings of this type are exceedingly thin. In an electrolyte of this type, the coating has a high resistance when the aluminum is made anode; consequently, any current that may flow (leakage current) is very

Jan 1, 1944