Search Documents

By Richard N. Hunt

Bingham has produced 6 per cent. of this country's copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham's silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. History of the Bingham District Bingham is on the eastern flank of the Oquirrh range 30 miles southwest of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep—an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century. During the past two decades one mine, the Utah Copper, has become so gigantic an operation as to dominate all other activity in the camp. It has become the greatest copper mine on the continent in production,

Jan 1, 1924

By J. E. Kirby, L. B. Schnitz, H. E. Stamm III

The production history of a gas-cap-drive reservoir was reproduced by calculations, and predictions were made for operations under primary depletion, pressure maintenance by gas injection, and pressure maintenance by water injection. Although the general equations used in this analysis have been available to the industry for a number of years, the procedure has not had extensive use because of the unusually large time requirements for developing numerical results. The use of digital computing equipment for processing the calculation work generally reduced the time usually required for an extensive analysis of this type. Calculation techniques were developed that were equally applicable for solving the gar-cap-drive problem, whether digital computing equipment or desk calculators are used. These techniques are outlined and the procedures are illustrated by the field problem. INTRODUCTION The analysis of a gas-cap-drive res-ervoir requires the simultaneous solution of the volumetric balance1 and displacement2 equations. Equations for the analysis of combination drive reservoirs were presented by Wooddy and Moscrip in a previous paper." These equations permit the evaluation of possible operating processes in order that the optimum method of pro- ducing the reservoir may be determined. Although these equations represent the basic technique known for the detailed analysis of gas-capdrive reservoirs, the calculation processes are quite complex and time consuming; hence, the procedure has not had extensive use. Recently, these equations were satisfactorily applied with the aid of a digital computer to investigate the completion history of a gas-cap-drive reservoir under the following operating methods: primary depletion, depletion under full pressure maintenance by gas injection, and depletion under full pressure maintenance by water injection. The use of digital computing equipment substantially reduced the time necessary for making the computations and permitted a more concise investigation of the reservoir's depletion history than was possible when the desk calculator was used. This more rigorous investigation also permitted a detailed analysis of the calculation procedures necessary in the solution of the gas-cap-drive problem. This paper outlines the procedure of analyzing a gas-cap-drive reservoir and illustrates the process with an actual field problem. CHARACTERISTICS OF THE RESERVOIR ANALYZED Production in the field under consideration is obtained from a Frio formation of Oligocene age at a depth of approximately 5,740 ft sub-sea. The accumulation, which is bounded on the flanks by strand lines, is semirectangular in shape with gentle narrowing toward the base of the structure as shown by the sand limits and completion map in Fig. 1. The reservoir development indicates an oil column of 319 ft that is defined by gas-oil and oil-water contacts. Basic data relative to the characteristics of the formation and the formation fluids are shown in Table 1. The formation exhibits considerable shaliaess and thinning near the oil-water contact indicating that little or no benefit will be received from natural water influx. This is substantiated by the fact that wells completed near the original oil-water contact have not produced water. A sizeable gas cap is present; however, considerable faulting is in evidence, and it is believed that only a limited portion of the gas cap will aid in oil displacement and pressure maintenance. Although the reservoir was in an initial stage of depletion, it was believed that as soon as the equilibrium gas saturation in the oil zone was exceeded and a number of upstructure wells were invaded by the expanding gas cap, the resulting high gas-oil ratio production would rapidly dissipate the natural drive and lead to limited oil recoveries and inefficient reservoir operation. This analysis evaluated the effectiveness of the primary displacement mechanism and

Jan 1, 1958

By Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mcxico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid curbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1938

By Orville R. Lyons

This paper presents a method whereby the amount of misplaced material and the difficulty of the separation can be used to compare coal cleaning equipment of all types, from effectiveness and capacity standpoints. The correlations presented do not include all types of equipment currently available, but the method can be used to evaluate any make or type of coal cleaning equipment, both old and new. THE relative performance of coal washing equipment, or the effectiveness with which any type or make of equipment removes impurities from coal, has been most difficult to evaluate in the past. The most widely used yardstick is the Frazer and Yancey efficiency formula developed in 1922,' but Yancey in a later article states that "washers treating coals of different density composition or operating at different densities of separation cannot be compared directly on the basis of this criterion."' Prior to and since 1922, a variety of other methods has been used for comparison purposes, including the distribution curve, the error area, and the "ecart probable" or probable error. Yancey and Geer in discussing these methods conclude, "Performance can be evaluated in a number of different ways, with the choice of the proper method to use being dictated by the objectives of the investigation and the data available."' It is true that performance can be evaluated in a variety of ways, but if the equipment is to be evaluated on an effectiveness basis, there should be only one universal comparison method. Varying methods have been used because one universal comparison method has not been found or developed. In the article previously quoted, Yancey and Geer state in clear terms the primary concept for a universal comparison method: "One of the simplest, and certainly one of the most obvious evaluations of washery performance is the quantity of sink material in the washed coal and the float material in the refuse. If the washery products are tested at the density at which the washing unit is operated, the sink in the washed coal and the float in the refuse represent material that has been misplaced." The quantity of misplaced material was used as a criterion of washery performance by Lincoln in 1913," by the United States Bureau of Mines in 1938,' by Hancock in 1947," and by the national French research agency Cerchar in recent years.' In 1950 Andersone proposed the use of this criterion as an efficiency value to replace the Frazer and Yancey formula. However, none of the above-mentioned investigators used the misplaced material concept in a manner that would provide universal coal-cleaning equipment comparisons. The Correlation Theory The ideal coal cleaning process would treat all sizes and would make a perfect separation at any given specific gravity. All material lower in density than the desired value would report in the coal product and all material higher in density would report in the refuse product. Unfortunately, no known cleaning process achieves this goal and there seems little likelihood that any process yet to be invented will do more than approach it. When coal is treated in volume under operating conditions, it is impossible to avoid mechanical entrapment, fluctuations in throughput and effective gravity of separation, and the creation of turbulent currents, even when a true heavy-liquid bath is used and the feed is closely sized and contains little intermediate gravity material. This being so, it is possible to appreciate the difficulties inherent in trying to obtain a perfect separation when treating a wide range of sizes and a feed containing high percentages of intermediate material, using turbulent currents to help create the effective separation gravity, under operating conditions which normally tend to be on the overload side. When coal is separated from refuse in any coal cleaning equipment, some refuse always reports to the coal and some coal to the refuse; the writer therefore assumed that there should be a relationship between the total amount of misplaced material produced by any given piece of equipment and the difficulty of separation as represented by the percentage of near gravity material in the feed. With small amounts of near gravity or k0.1 material in the feed there should be less misplacement of material than would occur with large amounts of near

Jan 1, 1953

By Robert B. Sosman

The chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily I I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting On a paper that I had recently published27 On "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of of Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. Scope of the Lecture During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyro-metric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the united States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the ((temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that " temperature of the furnace " is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1949

By Robert F. Mehl, Gerhard Derge

The gamma-alpha transformation in iron and iron-rich alloys is of such practical and theoretical importance that many papers have been published upon the subject relating to critical temperatures, transformation rates and accompanying property changes. Although crystallo-graphic studies are of less immediate practical usefulness, the opportunities which these offer to furnish data on the basic atomic movements which characterize the transformation are not to be neglected1. The early work on the crystallography of this transformation has been reviewed in the fourth paper of this series2; since then several important papers have appeared. Our present knowledge may be briefly summarized as follows. Kurdjumow and Sachs, working with a 1.4 per cent carbon steel3, established the orientation relationships subsisting between the face-centered gamma and the metastable tetragonal lattices in freshly quenched martensite, and between the face-centered gamma and the body-centered alpha lattices in tempered martensite. The orientation relationship observed in the latter case may be stated in terms of planes and directions observed to lie parallel in the two lattices: {111} ?//{110}a [110] ?// [111]a (This notation is used throughout as the most descriptive means of expressing the fact that any (111) plane of the gamma phase may be parallel to any (110) plane of the alpha phase, and that a [110] direction in a particular (111)? plane is parallel to a [Ill] direction in the corresponding (110)a plane.) From these relationships the atomic movements that transform the gamma lattice into the alpha may be inferred. In the present experiment these may be considered as consisting primarily in a shear of the atoms parallel to the {111} planes in [110]? Directions

Jan 1, 1937

By G. H. Enzian

THE effects of phosphorus and nitrogen on the properties and behavior of low carbon steels are important considerations to both the manufacturer and the user of such material. For one thing, these two elements are the principal points of distinction between the chemical compositions of Bessemer and open-hearth grades. Further, open-hearth steels themselves may vary considerably in nitrogen content depending on the raw materials and ..practice used. In addition, appreciable amounts of rephosphorized open-hearth steels are being used at the present time in some low alloy, high strength grades and in certain other cases. For these and other reasons, it was felt desirable to obtain more complete knowledge of the effects of simultaneous small variations in phosphorus and nitrogen content on such properties of low carbon steel as tensile strength, impact toughness, sensitivity to cold work, and strain aging. A long range investigational program designed to furnish such information, was carried out, and the present paper summarizes some of the data currently obtained. General Discussion The strengthening effect of relatively small amounts of phosphorus in steel has been recognized, and to some extent utilized, for many years. A number of investigators have pointed out, from time to time, that under proper conditions of control, phosphorus can be a useful alloying element in low carbon steels.1-3 Nevertheless, in spite of the volume of data on the subject, the use of phosphorus for this purpose has always been handicapped by widespread feeling that its presence makes the steel brittle, difficult to cold work, and unreliable at low temperatures. This belief on the part of some steel users is not entirely justified in many cases, and often stems from early experience with acid Bessemer steels which have appreciably higher phosphorus (and nitrogen) contents than basic open-hearth grades. Nitrogen in steel, and its effect on properties, has also received considerable attention in the literature.4 In 1906, Braune5 ascribed the brittleness of Bessemer rails to the nitrogen content, and proposed a schedule of nitrogen limits for steels for various uses. This was one of the first papers to recommend directly the use of nitrogen content as a quality control measure, but it did not meet with much favor or support; as a matter of fact, the Jernkon-toret was rather sharply criticized for publishing the paper. In the intervening years a number of papers have been published on the subject of nitrogen in steel. As a result, it is now generally recognized that nitrogen can have an important effect on the properties and behavior of steel and that the presence of this element should be considered in any systematic study of factors affecting steel quality. In 1932, Graham6 introduced the concept that the quality of various steels could conveniently be evaluated and compared in terms of "sensitivity", which was defined as "the characteristic reaction rate of a piece of steel toward brittleness or hardness." This concept formed the basis for a broad research program into factors causing variations in the quality of commercial steels. At an early stage of this work, it became apparent that the observed effect of either phosphorus or nitrogen on the sensitivity of steel depended, in no small measure, on how much of the other of these two elements was also present. Indeed, the combined effect of phosphorus and nitrogen in steel may often be more important than the specific effect of either. With a few exceptions, it is not possible to predict accurately the effect on steel properties of a change in the amount of either phosphorus or nitrogen in the steel without also specifying the approximate amount of the other element. It seems desirable, at this point, to discuss briefly the distinction between strain-sensitivity and strain aging as used in this paper. In the early stages of its development, the work-brittleness test7 (which will be described in more detail later) was used

Jan 1, 1951

By Robert M. Yonco, Irving Johnson, Martin G. Chasanov

The thermodynamics of the cadmium-rich portion of the Pu-Cd system has been studied with a high-temperature galvanic-cell method. The partial phase diagram of the Pu-Cd system was determined. The existence of the intermediate phases PuCd11 (cubic BaHg11 structure, ao= 9.282) and PuCd6 (cubic, CeCd6 structure, a, = 15.59) was established. The existence of at least one other intermediate phase richer in plutonium was indicated. PuCd11 was found to peritectically decompose into PuCd6 and liquid at 406" * 2°C. The solubility of plutonium in liquid cadmium may be represented by the equations: (355' to 399°C) log (at. pct Pu) = 6.223 -4282T-1 (399° to 632°C) log (al. pct Pu) - 5.148 - 5277T-1 > 1.156 x 106 T-2 The free energy of formation values (kcal per mole) of the two intermetallic phases are given by the equations: (PuCd11), ?Gf= -45.9 + 35.7 x 10-3 T (PuCd6), ?Gf0- -39.27 + 25.86 X 10-3T The excess free energy (kcal per mole) of plutonium in liquid cadmium may be represented by the equation: -(-16.72 * 29.54 NPu) 10-3T in which Npu and Ned are the atom fractions of plutonium and cadmium. The thermodyanamics of the U- Cd and Pu-Cd systems are compared. THERMODYNAMIC information on systems of the actinide metals with low-melting metals, such as zinc and cadmium, is useful in the design of pyro-metallurgical processes for the purification of nuclear reactor fuels. The thermodynamics of the Pu-Zn,1 Th-Zn.2,3 U-Zn,4-5 and U-Cd6 systems have been reported. The present report on the Pu-Cd system concerns the liquidus composition in the cadmium-rich region, the characterization of the two most cadmium-rich intermetallic phases, and the thermodynamic properties of these intermetallic phases and dilute liquid solutions of plutonium in cadmium. EXPERIMENTAL Phase Studies. The liquidus composition was determined by analysis of filtered samples of the liquid phase withdrawn at a series of temperatures. The apparatus and procedure were identical to that used in the previous study of the Pu-Zn system.' Briefly. a sample of the melt was withdrawn into a tantalum tube fitted with a porous tantalum filter (30-µ pore). the entire sample dissolved in hydrochloric acid (to avoid errors due to segregation

Jan 1, 1965

By Bruce Chalmers, D. C. Larson

Aluminum crystals with longitudinal-axis orientations of (111) . (110), and (100) were deforined in tension and annealed. The conditions of deformation were controlled so that the re crystallization nuclei originated in either the heavily deformed regions at saw cuts {artificial nucleation) or in the lightly deformed matrix (spontaneous nucleation). The artificial-nucleatioln experiments showed that in lightly deformed (110) and (100) crystals low-angle twist boundaries are most mobile, while in (111> crystals and heavily deformed (110) and (100) crystals high-angle tilt boundaries with near (111) rotations are favored. The spontaneous-nucleation experiments showed the existence of preferred orientations in the (111) crystals. The nonrandomness of the grain orientations is quantitatively determined through a comparison with the results which would he obtained from a randowl set of grain ovientations. PREVIOUS recrystallization studies have been performed on single crystals deformed in tension.1 7 The crystals used in these studies usually had random tensile-axis orientations and the extent of deformation was not a primary consideration. The present study concerns the recrystallization of single crystals with tensile-axis orientations of (Ill), (110), and (100). The emphasis of this work is on the influence of the tensile-axis orientation and the degree of deformation on both the nucleation and growth processes. The multiple-slip orientations were chosen because secondary slip or slip intersection promotes nucleation.1,5,8 These crystals recrystallize at lower strains than the crystals which are oriented for single slip. Also, the greatest variation in deformation behavior is exhibited by the multiple-slip orientations. The stress-strain curves for crystals with tensile-axis orientations of (111) are higher than the stress-strain curves for poly-crystals, and the stress-strain curves for crystals with tensile-axis orientations of (100) are lower (at large strains) than the stress-strain curves for the crystals which deform initially in single slip.g The recrystallization nuclei originated in either 1) the homogeneously* deformed matrix of the crys- tals or 2) the heavily and inhomogeneously deformed regions at saw cuts. The nuclei will be referred to hereafter as spontaneous and artificial nuclei, respectively. The two terms do not imply a difference in the nature of the nuclei; they imply simply a difference in the mode of introduction of the nuclei. During spontaneous nucleation very few (always less than ten) grains nucleate, while during artificial nucleation large numbers of grains nucleate. Only a fraction of the artificially nucleated grains penetrate very far into the deformed matrix during annealing. The grains that penetrate the farthest into the deformed matrix will be referred to as the dominant grains. EXPERIMENTAL PROCEDURE The thirty-five crystals used in this investigation were grown from the melt in milled graphite boats at a rate of 1.6 cm per hr. The crystals had dimensions of approximately 6 by 12 by 80 or 6 by 6 by 80 mm and the aluminum was of 99.992 pet purity. The as-grown crystals were annealed at 610°C for 24 hr and furnace-cooled. They were then heavily etched and electropolished in a solution of five parts methanol to one part perchloric acid. The crystal orientations were obtained by back-reflection Laue photographs and were accurate to ±2 deg. The tensile-axis orientations were (loo), (110), and (111). Two of the side faces of the (111) crystals were (110) lanes. The (110) crystals had both {100) and {110) side faces and the (100) crystals had (100) side faces. The crystals were deformed at a strain rate of 0.003 per min. Shear stress and shear strain were obtained by multiplying and dividing the tensile stress and strain, respectively, by the Schmid factor, m. For the (111) crystals m = 0.272 and for the (110) and the (100) crystals m = 0.408. The Schmid factor is effectively constant during deformation for all orientations. The deformed crystals were sawed into 1-in.-long specimens while the crystals were totally enclosed in a graphite boat. The sawing was performed very carefully in order to limit the plastic deformation to the sawed regions. The specimens were electropolished in the solution mentioned above to remove the sawed-end deformation as well as controlled amounts of surface material. A special stainless-steel grip was used to hold the specimens during the electropolishing treatment. The gripping faces were flat, with no teeth, to prevent the introduction of extraneous de-

Jan 1, 1964

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By J. L. Gillson

In a brief summary of the many occurrences of fluorspar in our western states, it is not possible to go into detail in regard to the geology, mining and milling methods, and reserves about individual deposits. Rather a broad review is made of the occurrences and an analysis of how the western deposits may fit into our future domestic economy is presented. General Statement on Fluorspar Situation Fluorspar has been used for years as a flux in the manufacture of basic open-hearth steel, in foundry cupolas for melting pig iron, in the manufacture of opalescent glass and in the preparation of hydrofluoric acid. In 1880 the annual production of fluorspar in the United States was around 4000 tons per year. By 1900 it was up to 21,656 tons and between 1902 and 1908 it averaged about 40,000 tons annually. Prices were then so low, by present standards, that it seems impossible to believe now that mining could have been performed profitably at the price levels then prevailing. In 1890 fluorspar sold at the mines for $6.70 per ton, in 1901 for $5.81, in 1916 for 85.92. When the United States entered World War I, flyorspar production and price skyrocketed; the production reached 263,817 tons in 1918, with prices above $20.00 per ton, and prices were even higher in 1919 and 1920. After 1920, the domestic production fell from the 1918 level to about 125,000 tons annually and the average price dropped back to about $18.00 per ton. By 1935 the average price had fallen to $15.00, but in 1940 with a rising demand the average price of all grades had gone back up to $20.31. Today it is 75 per cent higher than in 1940 and presumably the price of acid grade at .least would be even higher if it were not for price ceilings. The first subsequent year that the domestic production exceeded that of 1918 was 1941, and the 1944 production is expected to exceed 400,000 tons, or over one and a half times that of 1918. In five-year periods, average production and imports were as are shown in Table I. Many people concerned with the consumption of fluorspar believe that the postwar period ahead will show a repetition of price trends of the last such period. They believe that imports will be again an important factor in the available supply and the price will fall back gradually toward the prewar level. The following basic factors are pertinent in analyzing this conclusion:

Jan 1, 1948

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By Charles Miller

Natural carbon dioxide has recently been exploited in the United States in consequence of oil and gas developments in the Western States and the growing demand by transcontinental and transoceanic shippers for solid carbon dioxide. The discovery by drilling of commercial deposits resulted in consideration of its geographic and geologic distribution and occurrence. Its wide distribution in nature is evidenced by its occurrence in the atmosphere, hydrosphere and lithosphere. The question of origin of carbon dioxide involves consideration of theories similar to those concerning natural hydrocarbons, although available evidence favors an inorganic rather than an organic source. Areas favorable to development of commercial production appear to be those in proximity to igneous rocks or in the vicinity of decadent volcanic activity, where, it has long been known, the gas is evolved either free or dissolved in the waters of fumaroles, geysers or mud pots. Structure contour maps are presented showing the Wagon Mound anticline in New Mcxico and the Farnham anticline, Utah. A well drilled on the latter supplies gas to a 20-ton plant manufacturing solid curbon dioxide at Wellington, Utah, on the Denver and Rio Grande R.R., whence it is shipped to surrounding territory and to the West Coast. Before funds are invested in a plant for the manufacture of liquid or solid carbon dioxide, whether supplied by wells or springs, an effort to ascertain the volume of gas available is advisable. The use of present methods of estimation of gas reserves with modifications to account for the quantity absorbed by any water present in the producing formation is recommended. The Farnham anticline is used as an example and computations are made of the probable volume of gas originally present in the structure. No attempt was made to compute reserves in the Niland area, California, for the reason that in such areas it is believed the volume is indeterminate. Introduction Carbon dioxide, in liquid and solid form, has found a wide variety of uses other than its primary application in carbonating beverages. It is now used in more than 40 different ways, ranging from cooling or freezing to use in gas or liquid form for mechanical purposes, chemical industry, explosive, fire extinction, and tire manufacturing. Undoubtedly the chief supply of carbon dioxide is obtained from industrial plants or artificial sources and until recently natural deposits of the gas have received little consideration. Few will question the utility and perhaps dependability of artificial sources, which possess the advantage over

Jan 1, 1938

Discussion of the paper of John H. Hall, presented at the New York. Meeting, October, 1913, and printed in Bulletin No. 79, July, 1913, pp. 1247 to 1256. WILLIAM 'R. WEBSTER, Philadelphia, Pa.:-I would like to call ,attention to the fact that the results of the ordinary tension and bend tests do not always give us the information we want even if we figure out the amount of work done. You want a bending test of sufficient width and full thickness. In the case of eyebars, for instance, I have had experience with a 10- by 1-in. eyebar which gave perfectly good results in a full-size test of the finished bar. The 10- by 1.5-in. and 10- by 1.75-in. eyebars from the same heats-of steel were absolutely worthless in full-size tests. The narrow bending tests from all these bars gave good results. Bat after going into the matter fully, we found that if pieces about 3 in. wide and full thickness were used for the. cold bending tests, the heavier material would not stand this test, but failed. That is, in order to check the quality of the rolled bar you should have a wide piece of full thickness for cold bending, as the narrow pieces give misleading results. J. E. JOHNSON, JR., New York, N. Y. :-I would like to ask if there have been any tests made to compare the results of Charpy tests with the true dynamic test similar .to the Wohler test, except that the piece is subjected to a tensile or compressive stress and to alternating stresses in addition, at the same time. This seems to me to approach more nearly than any other test to the conditions of actual service. where the piece is under a fixed initial stress plus a highly variable and often alternating stress. Some tests were made on this plan in England within a year or two. The test piece was Subjected to either a tensile or compressive stress of known amount and simultaneously to alternating stresses in addition. Such a. test as this gives information which we cannot get by a tensile test or even from the tensile strength multiplied by an. elongation. Such tests, however, are exceedingly tedious and require long periods of time in order to obtain valuable results. If material could be subjected to these dynamic tests and the same material to the. Charpy shock test, and if some reasonable qualitative relation could be established between the results of the two tests, then we could assume that the shock test, which is so simple and easy to make, was a measurably accurate test of the dynamic qualities of the material. At present it does not seem

Jan 12, 1913

By Robert B. Sosman

The chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily I I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting On a paper that I had recently published27 On "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of of Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. Scope of the Lecture During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyro-metric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the united States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the ((temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that " temperature of the furnace " is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1949

By H. H. Smith, G. J. Danek, M. R. Achter

Nickel, Type 316 stainless steel, and copper show decreases in reversed bending fatigue strength with increases in air and oxygen pressure. The leveling off of the log N us log p curve for nickel at 300" and 816°C is discussed in terms of a model in which surface saturation gives rise to a critical pressure. A metallographic study indicated that the effect of environment on crack initiation and growth rates is a function of temperature. It is shown that small amounts of impurities in inert gases may substantially reduce the fatigue strength of nickel. 1n a previous investigation1 of high-temperature bending fatigue in air and in vacuum, reversals in the effect of environment with changes in test conditions were atrributed to a mechanism consisting of two processes acting in competition. One of them, oxidation strengthening, has been demonstrated in a straightforward manner by measuring the rupture strength of a sintered nickel-oxide bond.' The detailed operation of the other process, facilitation of crack propagation by surface absorption of oxygen, is uncertain. Thompson et UZ advanced the possibility that the formation of an oxide layer prevented rewelding of cracks during the compressive part of the cycle, while Wads worth and Hutchings4 further proposed that the reaction of oxygen with atoms at the tip of the crack helped the metal to break there, a possibility which has also been advanced to explain crack formation in creep.5 A difficulty in arriving at a mechanism for this lowering of fatigue strength in air is the inconsistency of some of the data. For example, Wadsworth and Hutchings4 found an approximately linear decrease of log cycles-to-fracture (N) with an increase of log pressure-of-air (p) for copper and aluminum at room temperature, while snowden,' although finding a similar linear dependence for aluminum, observed a stepped curve for lead. Between l0-' and 10"1 torr there is a sharp decrease in the fatigue life of lead with increasing air pressure, but plateaus, signifying no dependence on pressure, are found at higher and lower pressures. If, as discussed elsewhere: these environmental effects arise from the adsorption of gas on crack surfaces, it would be expected that as the pressure is increased a saturation point would be observed, beyond which there is no further effect. To gain further information about the form of the log N vs logp curve, it was decided in the present investigation to repeat this type of measurement at elevated temperature on nickel, copper, and Type 316 stainless steel. An additional object of this program was

Jan 1, 1963

By E. A. Anderson, M. L. Fuller

The copper-zinc phase equilibrium diagram has been the subject of many investigations. Until recently, however, the boundary of the terminal solid solution of copper in zinc (eta) has not been thoroughly investigated. This paper reports determinations of the solid solubility of copper in zinc at temperatures from 100' to 400' C., the course of the liquidus and solidus for the eta solid solution and determinations of the peritectic temperature and peritectic point for the reaction between epsilon and the melt to form eta. The liquidus of the eta phase was determined by thermal analysis and the solidus by the microscopical examination of specimens quenched from temperatures above and below the solidus. The temperature of the peritectic horizontal was obtained by thermal analysis and the composition at the peritectic point was determined by extrapolation of the solid solubility boundary of the eta phase to the peritectic horizontal. The solid solubility boundary of the eta solid solution was investigated very carefully. Particular care was used to achieve equilibrium in the alloys at each temperature selected. The X-ray, electrical conductivity and microscopical methods mere used in determining the solid solubility limits. The X-ray method measures the changes in the solvent lattice with increasing solute content and in this manner locates the composition of the alloy at which no further change in the solvent lattice takes place, the limit of solid solubility. The method of electrical conductivity measures the conductivity of the alloys of a graded series of compositions, whereby the solubility limit is indicated by a discontinuity in the conductivity-composition relationship. The microscopical method distinguishes, by direct inspection, between the homogeneous solid solution alloys and those having a secondary constituent in addition to the solid solution phase, and thus indicates from the examination of a series of alloys the solid solubility limit.

Jan 1, 1934

By Oliver Bowles

Dimension stone is a term applied to stone sold in blocks or slabs of specified shapes and usually of specified sizes, contrasted with crushed, broken and pulverized stone covered in another chapter. Dimension stone includes cut stone, rough building stone, ashlar,* rubble, monumental stone, paving blocks, curbing, flagging, and many types of ornaments and novelties carved from stone. Riprap-large, irregular blocks used for shore protection-is classed with crushed and broken stone. Composition, Varieties, and Properties Dimension stones are of many kinds. The principal varieties are granites, trap rock (diabase, basalt, and gabbro), sandstone, limestone, and marble. Slate is covered in a separate chapter. Granite is a visibly granular crystalline rock consisting essentially of feldspar, quartz, and mica or hornblende. The basaltic rocks are darker in color than the granites. They contain little or no quartz and consist largely of plagioclase feldspar, augite, pyroxene, and hornblende. They are classed commercially as black granites. Limestone consists essentially of calcium carbonate. Dolomites and magnesian limestones used as dimension stone are classed with the high-calcium limestones. Marble is a crystalline form of limestone, but in the trade, any carbonate rock which will take a polish is called a marble. Many limestones which are fossiliferous but which will take a polish are sold as a decorative stone for lobbies of hotels and office buildings. Sandstone consists essentially of silica in the form of sand grains cemented into a coherent mass. Although rock occurrences are numerous and widespread, the exacting requirements of use condemn all but a small fraction of them for commercial use as dimension stone. No deposit that has closely spaced joints or planes of weakness can be used because sound blocks of moderate to large size are demanded. Uniform texture and grain size, constant and attractive colors or color pattern, and freedom from impurities that may cause stains or deterioration usually are demanded. Hardness is a variable property. Granites and diabases are as hard as or harder than steel, while limestones and marbles may be scratched with a knife. The hardness of sandstone depends upon the degree of cohesion of the grains. Workability depends to a considerable extent on hardness, but the degree of hardness has little influence on use except where stones are subjected to abrasion as on steps or floors. "Texture" as applied to stone relates to the arrangement, uniformity, and size of the constituent grains. Stones are of many colors and thus can satisfy a variety of tastes. For monumental stone, a marked contrast between polished and tooled surfaces is preferred in order that inscriptions may be read easily. Strength requirements usually may be disregarded because any sound structural stone suitable in other respects is almost invariably many times as strong as would be required for any ordinary use. The pressure on the base course of the Washington Monument, Washington, D. C., is less than 700 psi, and highgrade granites, limestones, sandstones, and marbles will sustain a crushing load of 10,000 to 25,000 psi. A structure made of stone with a crushing strength of 15,000 psi would have to be nearly 21h miles high before crushing of the lower courses would occur. However, stone disintegrates more readily under severe

Jan 1, 1960

By H. A. Lequear, J. D. Lubahn

A sudden change from one constant strain rate to another during a tensile test causes an unusual transient in aluminum alloy 61ST. A sudden change from one constant stress to another during a creep test does not produce an unusual transient in this material. A specially devised test shows that the nature of the previous steady-state conditions, which the sudden change disturbs, is one of the factors affecting the transient behavior. Some of the observations may be explained in terms of strain aging. USUALLY a sudden change during a tensile test from one constant strain rate to another causes a small, abrupt vertical shift from one stress-strain curve to another, parallel one. This behavior is apparently characteristic of all metals at very low temperatures and of many metals for wide ranges of temperature. It is illustrated in Fig. 1 for some early data on 61ST tested at — 195oC, and in Fig. 2 for some recent data on copper at room temperature. The greater accuracy of the results of Fig. 2 over previous ones' is due to the equipment shown in Fig. 3. Three levers apply the bulk of the load, while the changes in the small remainder load are indicated sensitively by a low capacity load scale. Refs. 2 and 3 describe the recording equipment. A test like those in Figs. 1 and 2 provides the information necessary to determine the rate sensitizrity, n,4 of the metal. ( a log s ) ? log s n = ------------------------ ----------------------------= ( a logs e, ? log e logS2-logS1 log S2/S1 log i2 — log e1 log e2/e1 where S equals stress: e is logarithmic strain or natural logarithm of (final gage length/initial gage length);" i is strain rate or de/dt: and n is rate sensitivity, rate of change of log stress with log strain rate at a given strain, or (a log S/a log i),. Normally, the rate sensitivity, n, is positive, which means that an increase in stress causes an increase in rate. However, certain exceptions, attributed to strain aging,5 have been observed. Fig. 2 indicates how rate sensitivity values are derived from the measurements. Table I summarizes the rate sensitivity values derivable from Fig. 1. In contrast to the behavior of copper in Fig. 2, the aluminum alloy 61ST, which strain ages when tested near room temperature, exhibits an unusual transient when the strain rate is suddenly changed,' as shown in Fig. 4. Initially, there is a comparatively sudden vertical shift of the stress-strain curve in a direction corresponding to the rate change, but then the curve gradually shifts back again. The initial shift is not as sudden as might be expected, because the testing machine is unable to achieve the impressed rate change instantaneously, as illustrated in Fig. 2. The behavior shown in Fig. 4 will be referred to as a tensile transient, the word tensile implying that the behavior was observed in a tension type of test. The corresponding test, where the strain rate is maintained constant except for the sudden change, will be called a tensile transient test. A creep transient, by contrast, will be defined as a temporarily abnormal behavior in a creep transient test, where there is a sudden change from one constant load to another.' In Fig. 4, a naive look at the gradually decreasing and then increasing load after a sudden rate incre-

Jan 1, 1957

By H. C. Chang, N. J. Grant, A. R. Chaudhuri

During the creep of coarse-grained polycrystalline magnesium at elevated temperatures, a nonbasal type of slip was found to play an important role in the deformation processes. The nonbasal slip traces were examined metallographically in eight specimens (13 grains) and the observed glide plane located stereographically for each grain. The tests were run at 500&apos; and 700°F at stresses of 148 to 786 psi. Based on these measurements and theoretical calculations, the crystallographic elements for nonbasal slip were determined. WHEN a metal deforms by slip, the conventional appearance of the slip bands on the surface of a specimen is that of straight lines. Such is the behavior of the face-centered-cubic metals, as for example, aluminum. The particular slip system on which slip occurs in these metals is governed by the criterion of resolved shear stress. Work on the body-centered-cubic metals a-iron,&apos;. &apos; molybdenum, and columbium4 has shown that the process of slip is somewhat more complicated than the simple gliding of one close-packed plane of atoms over another in a close-packed direction and that it results in the formation of wavy and irregular slip traces on the surface. The recent reviews and experiments of Vogel and Brick and Chen and Mad-din3 show that, for the body-centered-cubic metals, the resolved shear stresses along the planes and the degree of close-packing do not necessarily determine the slip system. Theirs and other investigations indicate that a complete understanding of the slip process in the body-centered-cubic metals is not yet possible. However, one behavior displayed by all these metals is that the slip direction is invariably one of the close-packed directions <11l>. The wavy nature of the slip-band traces has been explained on the basis of cooperative slip by planes sharing this same slip direction.1&apos;3l&apos; It is generally acknowledged that, when the hexagonal-close-packed metal magnesium (axial ratio c/a = 1.624) deforms by slip at room temperature, it does so by basal slip in the close-packed direction <1I%>. This type of slip has the conventional appearance of straight lines and is governed by the critical shear-stress law. Schmid and coworkers" showed that basal slip was operative in the temperature range of —185" to 300°C (—300" to 572°F). Work by Servi, Norton, and Grant6 has shown that, during the creep of coarse-grained aluminum at high temperatures, new slip systems come into operation. The existence of a new high temperature slip system at temperatures greater than 225 °C (437°F) for magnesium was suggested also by Schmid. This was later indicated by Bakarian and Mathewson&apos; to be slip along the pyramidal planes (10i1) in the close-packed direction <11%>.* They * Mention will be made in the text of pyramidal planes and prismatic planes. The pyramidal planes referred to are the type I. order 1 of the form {10il); and the prismatic planes of the type 1 of the form (10i0). For the sake of brevity, they are termed in the teat as pyramidal (10il: and prismatic (10i0) planes, respectively. Where reference is made to the pyramidal plane type 1, order 2 of the form {10i2), they are referred to as the pyramidal planes of the type (10i2:. observed that this kind of slip resulted in irregular markings on the specimen surface. According to them, a possible cause for the appearance of the markings was due to "limited accessory slip on the pyramidal {10i2) planes." Burke and Hibbard," on deforming a single crystal of magnesium at room temperature, found evidence of slip on a pyramidal plane {1011). They explained it as being due to the effect of grip restraints. It is pertinent to note at this point that, although basal slip has received a fair amount of attention, only two specimens have been investigated, that of Bakarian and Mathewson and of Burke and Hibbard, to establish the elements of nonbasal slip in magnesium. During the study of the deformation mechanisms

Jan 1, 1956