Search Documents

By D. W. Akins

The case history of a combination gas and water flood instituted early in the life of a field is described. It was recognized from the beginning that recovery would be low, under normal production methods, from the several separate, thin beds of porous limestone which had such poor native permeability that the wells would not produce without acidizing. It is thought that the combination flood gives excellent recovery efficiencies for this type of reservoir. The chief function of the gas flood now is to maintain bottom hole pressure in that part of the reservoir which will not be affected by the water injection program until later. Present estimates are that ultimate recovery will be approximately double the recovery expected under the original solution gas drive mechanism. Wide (80-acre) spacing has enhanced the economics of the over-all field program by the elimination of more than $5,000,000 worth of unnecessary wells. INTRODUCTION The Haynesville Pettit Field was discovered in November, 1941, with the completion of T. L. James Co.'s Callie Akin No. 1, located in the W 1/2 of the NE 1/4 Section 27-23N-8W, Claiborne Parish, La., at an approximate depth of 5,300 ft. The center of the field is about two miles north and a mile west of the town of Haynesville, La. A total of 189 producing wells have been drilled on 14,500 acres. An additional nine dry holes were drilled. The Louisiana-Arkansas state line divides the field so that 34 wells are in Arkansas and 155 are in Louisiana. Governmental sections are divided equally to contain eight production units making 80-acre spacing where the sections are regular. Along the state line in Louisiana there is an irregular tier of sections, each of which contains approximately 456 acres. When divided equally into eight production units the spacing is 57 acres per well for these three and a fraction productive sections. All Haynesville Pettit wells are identified by their section number followed by their position in the section as determined by numbering the production units counterclockwise beginning in the upper right corner of the section. All of the producing wells in the field except two are unit-ized and operated by the Haynesville Operators Committee. These two wells are located in the extreme northern part of the field in Arkansas. Efforts to bring them into the Unit are being continued. The Pettit operators organized the Haynesville Operators Committee and the field became a unit operation May 1: 1944. GEOLOGY The Pettit is Lower Cretaceous in age and is defined as the uppermost porosity in the Sligo formation. The unitized area known as the Haynesville Pettit Field is composed of two separate zones of porosity approximately 40 ft apart and without connection between the two, except in wells. These zones are known as the Upper Pettit and the Lower Pettit. The Upper Pettit is separated into two sections throughout most of its area by a relatively thin but quite impervious shale streak. These are called the "A" and "B" sections of the Upper Pettit. All of these lenticular zones are composed of coquina limestone and a small percentage of normal oolites. The large

Jan 1, 1951

By Gordon M. Yocom

A pRopeR consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modem methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that he possesses chemical laboratory notebooks

Jan 1, 1941

By C. E. Lesher

THE Disco* process for the production of low temperature coke and its immediate predecessor, the Wisner or Carbocite process have been described in the voluminous literature of low temperature carbonization.1 This paper will describe the development of the process from the first attempt at commercial operation by the American Gas and Electric Co. at Philo, Ohio, Yn the 1920's to the successful operation in 1949 by the Disco Co., a division of the Pittsburgh Consolidation Coal Co., of the 1000-ton per day Disco plant near Pittsburgh, see Figs. 1-2. In the 1924 coal industry depression following the hectic post World War I expansion, the northern Appalachian, unionized bituminous coal fields were affected first and foremost, and Western Pennsylvania as hard as any. Competitive market pressure was heaviest on the lower grades of steam coals, notably the from the Panhandle district where ash and sulphur are inherently higher than in the same Pittsburgh coal bed to the east along the rivers. The firm structure of Panhandle coal while favoring the prepared sizes, depressed the usefulness and value of the finer sizes. Panhandle slack and nut slack were marketed with difficulty at consistent, and at times considerable, loss. Many solutions were suggested, and the Pittsburgh Coal Co. investigated all. Lower delivered prices through lower mine costs and more advantageous freight rates were obvious goals, but equally obvious were the difficulties of self attainment of either in any substantial measure. Selling Btu's in pipes was abandoned as an idea after a thorough study of the economics of distribution of what was then, and is even now, the only developed continuous process of complete gasification of bituminous coal-producer gas. Although the coal company purchased huge blocks of electric power, it sold not a car of coal to the central power stations. Public utilities controlled the markets for electric current, and it was found that no matter at how low a cost current might be put on the bus bars by the coal company, distribution to its widely scattered coal mines made such an enterprise practically impossible. Consolidation of underground operations and a huge modernization program of mining operations in the 1920's were but preparation for the introduction of mechanical cleaning of the coal for market, particularly the smaller sizes of steam, gas, and by-

Jan 1, 1953

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Morris Muskat, J. M. McDowell

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By M. Cohen, B. L. Averbach

Many hardened steels contain significant quantities of retained austenite even in cases where the carbon and alloy contents are low. In fact austenite has been detected in plain carbon steels containing as little as 0.50 pct carbon.1 Although the austenite may not be visible metallographically it causes definite dilatometric and magnetic effects during subsequent tempering or sub-atmospheric coo1ing.l,2,3 Therefore if the reactions which hardened steels undergo during later treatment are to be understood in quantitative fashion it is most essential to have some kind of absolute analysis for the austenite content in hardened steels. Once this analysis has been made, the austenite transformations can be followed precisely by observing such sensitive phenomena as changes in length or in magnetization but the latter techniques can only determine differences in the amount of retained austenite and usually an independent method must be found to put these differences on an absolute basis. In certain instances the microscope can be used advantageously to determine the percentage of retained austenite. The quenched sample is tempered to "darken" the martensite with minimum decomposition of the coexisting austenite, and then is polished and etched in the usual fashion. If the austenite is clearly distinguishable from the tempered martensite and other possible constituents its volume percentage can be measured quantitatively by point counting or lineal analysis.4 Such microscopic methods, however, depend on the etch being sufficiently discriminatory. In fairly coarse structures, if the austenite content is greater than 10-15 pct, there is probably little smearing of the etch, and point counting or lineal analysis seems to be quite accurate. On the other hand if the structure is difficult to resolve, as in commercially treated fine-grained . steels which contain less than 10-15 pct retained austenite, the latter may be completely obliterated by the dark etching martensite or it may appear disproportionately low as the interfaces between the two constituents become difficult to distinguish. Another disadvantage of the metallographic method is the need for "darkening" the martensite and hence the determination cannot be applied to as-hardened steels. The required tempering may spoil the structure for other tests or may even remove a small part of the austenite which is being sought. X ray methods hold more promise for covering the range under 15 pct retained austenite. Although austenite and martensite in the hardened steel may be chemically identical, their crystal structures and lattice parameters differ, and the intensity of an austenite diffraction line is some continuous function of the percentage of re-

Jan 1, 1949

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Athough the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time, All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. TEe Gamma-ray Curve The measurement of gamma-ray intensi ties is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is Med with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By M. Muskat, M. O. Taylor

Theoretical calculations have been made on the performance to be expected of gas-drive reservoirs for various characteristics of the oil and gas and the producing rock. Such performante has been expressed graphically as curves for the reservoir pressure and gas-oil ratios of the production as functions of the cumulative oil recovery. The latter has been expressed in terms of percentage of pore space of the reservoir rock. Such curves automatically give values for the ultimate physical recovery, if the latter is interpreted as the recovery obtained when the reservoir pressure has declined to atmospheric, or to any other pressure chosen as defining the state of practical complete depletion. Calculations of these pressure and gas-oil ratio histories have been made for conditions in which the oil viscosity, the gas solubility and shrinkage, the size of an overlying gas cap, if present, the permeability-saturation characteristics of the rock, and the amount of connate water, have been individually varied, The results serve to show the extent to which the ultimate recoveries are sensitive to the important physical parameters characterizing the oil reservoir. As is to be expected, the ultimate recoveries are found to decrease with increasing oil viscosity. Because of the predominant effect of the oil shrinkage associated with the liberation of the gas in solution, the ultimate recovery will decrease with increasing gas solubility. Increasing gas-cap volumes lead to higher recoveries, although the contribution made by the gas-cap gas is small as compared with the oil expulsion by the equivalent amount of solution gas. As a whole, the oil recovery when expressed in percentage of the pore space is not very sensitive to the details of the permeability-saturation relationship. However, if the rocks possess an equilibrium free-gas saturation, the rise in gas-oil ratio will be retarded, and the 'ultimate recovery somewhat increased' The oil shrinkage associated with the liberation of the dissolved gas also leads to the result that as long as the connate water is immobile and the permeability ratio curve for the rock is a function only of the total liquid saturation, the stock-tank oil recovery will be less for a sand containing no connate water than for One with an Original water content as high as 3' per cent. The space voidage in the former case will be somewhat greater, but the effect of oil shrinkage will lead to smaller values for the equivalent stock-tank recovery. These calculations also give data showing how the productivity indexes for the producing wells will vary during the reservoir history. Because of decreasing Permeability to the oil and increasing oil viscosity, the productivity index will fall continuously as Production proceeds, and may finally reach values as low as 10 per cent of the initial productivity index. Introduction In a previous paper1 was developed the basic theory for the prediction of the production histories of gas-drive reservoirs. The data required for the application of this theory included the characteristics of the petroleum fluids, such as the viscosity of the Oil and gas phases, the solubility of the gas in the oil, and the oil shrinkage— all expressed as functions of the reservoir pressure—and the permeability-saturation characteristics of the producing rock, as

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm's law and d'Arcy's law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By E. O. Jones

DURING the heating of cold-worked nickel silver, the tendency of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. CHANGES IN ALLOYS DURING HEATING AND COOLING During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320° C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 7, 1925

By Richard E. Gray, Robert W. Bruhn

INTRODUCTION Underground coal mining has been practiced in the United States for over 200 years. Much early mining was not as efficient as today and unrecovered coal pillars, often of variable size and spacing, remain to support the overlying strata after mining has ceased. These conditions constitute a potential subsidence problem since the pillars will eventually fail. The possibility of subsidence above an abandoned mine must be anticipated except when total extraction has been achieved, permitting subsidence concurrent with mining, or when large coal pillars which have an adequate factor of safety for long-term support remain in the mine. Coal is found in 37 states and is mined under- ground in 22 states (HRB Singer, Inc. 1980). Underground mining produced 40 percent of the 7.5 x 10" kg. (830,000,000 tons) of U. S. coal mined in 1980 (Keystone, 1981). There are approximately 70,000 abandoned or inactive underground coal mines in the United States and approximately 2000 active underground coal mines (NAS/NAE, 1975). Underground coal mining in the United States will eventually extend beneath 162 x 109m2 (40 million acres). Thirty-two billion m2 (8 million acres) are already undermined (HRB Singer, 1977). Subsidence due to mining has affected more than 8 x 109m2 (2 million acres) in 30 states, 7.7 x 10 9m2 (1.9 million acres) from bituminous coal mining and the remainder primarily from anthracite mining (Johnson and Hiller, 1979). Subsidence from all other underground mines has affected only 6.9 x 10 7m2 (17,000 acres) (Johnson and Miller, 1979). Subsidence appears to be particularly widespread in two states, Pennsylvania and Illinois, although serious subsidence is found in localized areas of numerous other states (HRB- Singer, Inc. 1977). Host underground coal mining has occurred in the eastern United States, where the U. S. Bureau of Mines estimates 1.6 x 109m2 (398,600 acres) in urban areas in 18 states (out of a total 1.7 x 109m2 1418,400 acres]) are threatened by subsidence (Table 1) (Johnson and Miller, 1979). Pennsylvania and West Virginia contain 57 percent of the total threatened areas. The U.S. Bureau of Mines estimates the total cost to stabilize the estimated 1.7 x lo9m2 (418,400 acres) of subsidence prone urban land located above abandoned mines is over $12.5 billion (1978 costs).

Jan 1, 1982

By Thomas C. Wilder

The concentration and activity of oxygen in liquid copper has been measured by the reversible galvanic cell: at 1100°and 1200°C for the concentration range of oxygen of 3 to 5600 ppm Measurements for approximately thirly alloys at each temperature indicate that the activity of oxygen roughly follows Henry's law, the activity coefficients of oxygen being 0.12 and 0.205 at 1100° and 1200°C, respectively. These results compare javorably with the results of seven other electrochemical and gaseous equilibrium studies on this system, the free energy of the solution reaction 1/2 O2 = O (7 at. pct in Cu, liq) being -18.10 * 0.30 kcal per gfw at 1200°C. Estimates of the standard molar free energy of formation of CupO(S) are also made. Praclicul consideration of this cell as an oxygen sensor for liquid metals is discussed briefly. SOLID mixed-oxide electrolytes which have a defect structure in the anion sublattice have recently become a very popular means by which the chemical potential of oxygen is measured at high temperatures. Since the pioneering work of Kiukkola and Wagner1 such electrolytes have been used in numerous cell studies for determining the thermodynamic properties of metallic oxides and oxy compounds, the partial pressure of oxygen in vacuum systems and other atmospheres, and the properties of oxygen dissolved in metals and alloys. The use of a solid electrolyte in a cell for a fast reliable method of oxygen determination in liquid metals would be a very important tool to the process metallurgist. In copper, for example, the oxygen content of the molten metal in the cathode furnace is a prime factor in determining the "set" or solidification profile of cast wire bars. In this investigation the activity of oxygen in liquid copper was measured by an electrochemical cell employing the electrolyte ZrO2 + 7 1/2 wt pct CaO. The cell used at 1100° and 1200°C was

Jan 1, 1967

By D. B. Kibler

THE Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County. This area is approximately 100 miles long and varies from 2 to 30 miles in width. Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon, Marion County, in the year 1888, by Albertus Voight, who lived within a few hundred yards of the spring. Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon. A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County. Phosphate was found in many places as "outcrops." Looking for outcrops was the first method used by the early prospectors in searching for deposits. Several years passed before any systematic method of prospecting was used. EARLY MINING The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons. The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from ½ to 1-yd. capacity. Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907. From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers. At some places, the overburden was loaded into side-dump skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine. The maximum depth of overburden that could be economically removed by hand labor, mules and scrapers was approximately 15 feet. About 1905 one of the companies erected a producer-gas powerhouse near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden. From the year 1888 through the year 1939, approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations. The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for the export trade. Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today only three companies are operating. These

Jan 1, 1941

By C. S. Barrett

It has been observed that deformation in iron takes place by slip on (110) + {112) + (123) planesl, 2, but in silicon ferrite with low deformation temperatures or high silicon contents (exceeding 4 per cent) the authors have found that slip is confined wholly to (110) planes, at least with small amounts of deformation. The purpose of the present investigation was to determine the effect of this alteration of slip mechanism on preferred orientations in cold-rolled and recrystallized strips. Incidental observations on the effect of the recrystallization temperature were also made. The numerous determinations of the texture of cold-rolled iron and steel have been in satisfactory agreement as to the principal features of the texture (with the exception of a few conclusions that apparently have been based on insufficient data). The texture is chiefly one in which 11101 directions of the grains lie along the direction of rolling, with a deviation of a few degrees, and in which the (100) planes lie in the plane of the rolled sheet, with a deviation from this position chiefly about the rolling direction as an axis. This deviation about the rolling direction as an axis has been measured by different observers and lies between about 45" and 50" or 60" for iron5, 6, 9 and is usually in the neighborhood of 50" for mild stee16, 7, 8. The range of this deviation is a function of the percentage of total reduction8, 10. Post8 reported that it decreases with increasing percentage reduction, but apparently he studied only the surface material, which Gensamer and Meh17 found to be somewhat differently oriented from the material in the inside of the sheet. McLachlan and Davey10 found that the deviation also decreases with increasing percentage of total reduction for the material in the interior of the sheet and is independent of the percentage of reduction per pass. The deviation about the cross direction as an axis (the direction in the

Jan 1, 1937

By P. R. Swann, J. G. Parr

Quenched structures were studied in alloys containing up to 12.5 pct cobalt. The subsequent decomposition of a 10 pct cobalt retained-ß phase alloy was investigated using metallographic and X-ray diffraction methods. Hardness measurements also were made during the decomposition process. Precipitation of Ti2Co is by nucleation and growth; and an activation energy of 50,000 cal per mole was determined. The values of the coefficient ß suggest that the precipitate is pearlitic at temperatures between 450 and 475°C, and spheroidal between 500 and 525°C. THIS paper describes part of a series of invesligations into phase transformations in binary alloys of titanium with transition elements. The general approach is similar to that taken in work on titanium-iron and titanium-nickel alloys.' Previous investigators'' have established the titanium-rich end of the titanium-cobalt phase diagram, reproduced in Fig. 1. Orrell and Fontana' showed that alloys containing more than about 6 pct" cobalt quenched from the ß range, produced 100 pcl retained-p phase. The isothermal decomposition of alloys containing between 0.8 pct Co and 15.5 pct CO was investigated by the same workers in the temperature range 650 to 1000°C. They reported that these alloys transformed into a or Ti,Co depending on the cobalt content, but no quantitative data were given. In the work to be described a series of alloys containing 0.8 pct Co to 12.5 pct Co was examined in the quenched condition. The 10 pct Co alloy (the lowest cobalt content to retain 100 pct ß on quenching) was selected for further work on the tempering kinetics of the ß decomposition. Experimental Procedure Since our own melting equipment was not installed at the outset of this work, the Physical Metallurgy Division of the Department of Mines and Technical Surveys (Ottawa, Canada) prepared the alloys. These were made of Japanese sponge, (which when melted had a value of 103 DPH, using a 1-kg load), and electrolytically prepared cobalt. The al- loys, made up to contain 0.8, 1.6, 3.3, 5.8, 8.3, 10.0 and 12.5 pct Co, were homogenized by swaging into rods at 900°C. Filings were taken from the rods, and any iron chips from the file were separated magnetically. Size fractions of both plus and minus 200 mesh (about 75p) were shown by their constitution, after annealing just below the eutectoid temperature, to contain the same cobalt content. Consequently, it was permissible to use the —200-mesh fraction, knowing it to be representative of the rod composition. Quenching in argon was carried out in a newly designed furnace, whose features include (1) an Inconel furnace tube, (2) a positive pressure of argon maintained at all times in the furnace—even when a sample is removed or inserted. The furnace is shown in Fig. 2 and is described in the Appendix. The tempering processes were carried out on powder samples sealed in evacuated quartz capsules. Since the highest tempering temperature was 525OC, no protection against reaction with the quartz was necessary. (Tests were made on filings of iodide titanium and showed no hardness increase after equivalent heat-treatments.) A thermocouple was attached to the capsule, which was heated to the

Jan 1, 1959

By Y. Nakada, B. Chalmers

The work-hardening behavior of surface layers of aluminum and gold single crystals was investigated by alternately deforming and then removing a thin surface layer by electropolishing or by etching. Aluminum crystals exhibited lower flow stresses after the surface removal; gold crystals did not. Abrasion of surface eliminated easy glide in both gold and aluminum crystals. By alternately deforming and removing the surface layer, it was shown that the abraded crystals work-harden preferentially under the abraded layer. It is suggested that this phenomenon is caused by the difficulty of propagating dislocations through the abraded layer. It has been demonstrated in numerous cases'-3 that the plastic behavior of metals in either single-crystal or polycrystal form is sensitive to the environment and to the condition of the surface; it has also been reported4-6 that single crystals of some metals, when deformed in tension, exhibit more work hardening near the surface than in the interior. A third type of effect that has been attributed to the special part played by the surface in plastic deformation is the influence of the dimensions of the specimen on the various parameters that define its plastic-deformation characteris- tics.?-'' Many of these experiments were made on aluminum, on which an oxide film is always present under available experimental conditions; many of the effects have been attributed to the oxide film, either in terms of its higher elastic moduli, which would cause local stress redistribution, or its higher strength, which would oppose the escape of dislocations at the surface of the metal. On the other hand, it has been suggested II,12 that the mere presence of a surface should be sufficient to produce the observed results. A rigorous examination of this question could, in principle, be carried out by comparing the behavior of aluminum with its oxide film with that of the same material without oxide. This experiment would present great difficulties. The most practical alternative is to compare aluminum with gold, which has no crystalline surface film at room temperature, and to study the effects of various surface treatments on gold. The experiments described in this paper fall into two groups, the objectives of which were to determine 1) whether single crystals of gold shared the property of aluminum that the removal of a surface layer after some plastic deformation reduced the flow stress for further deformation and, since the result of this was negative, 2) whether a surface treatment could be found that caused gold to behave in this way. I) EXPERIMENTS AND RESULTS All the tests described below were carried out on single crystals of about 6 by 6 mm cross section and of sufficient length to provide a gage length of about 10 cm.

Jan 1, 1964

By Frederick L. Knouse

THE south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19° to 21° and 30" south latitude; and from 40° to 41° and 30" west longitude. This includes the central part of Espirito Santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Martines, Espirito Santo (Fig. 1). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through Vitoria; and by the E. F. Minas-Vitoria and E. F. Central do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatites, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. EARLY OPERATIONS Mining of quartz crystal in this region began in 1928, and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crystal as small as 10 grams. Since 1941 only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of loo grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, or Domingos Martines, Espirito Santo. Marketable quartz crystal was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large cores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. PRODUCTION The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1946

By J. M. McDowell, Morris Muskat

In both production and refining operations of the oil industry many processes are controlled by the gas-liquid phase relationships of the hydrocarbon mixtures of interest. The quantitative behavior of fractionating or distillation columns and stills depends on the changes in the equilibrium distributions of the hydrocarbon components between the gas and liquid phases as the pressure or temperature conditions may vary along the length of the column or as the gross operating parameters and compositions are varied. In oil producing operations the nature and amount of gas phase developed within an underground reservoir as it is being depleted and its pressure declines also involve the basic equilibrium gas-liquid phase interactions. The influence of surface conditions of temperature and pressure and various separation procedures on the nature and amount of stock tank oil and natural gas recovered from a given well stream is likewise determined by the same basic phase equilibrium characteristics of the hydrocarbon systems. Such equilibrium separation of the gas and liquid phases in a well stream is of importance both in establishing optimum separator conditions for obtaining maximum stock tank oil yields and in the general problem of crude stabilization. The phenomena involved in these problems and their quantitative aspects can, of course, be established in each individual instance by appropriate laboratory experimentation. It has been found, however, that by associating with the individual hydrocarbon components functional characteristics de- scribing their individual gas - liquid phase equilibrium behavior, the phase properties of the composite mixtures can be predicted by mathematical computation. These characteristics have been termed "equilibrium constants", or "equilibrium ratios"," and are defined by the general equation: where K, is the equilibrium ratio for the jth component, y, is the rnol fraction of that component in the gas phase, and xj is the corresponding mol fraction in the coexisting liquid phase. Considering the Kj as representing available and measurable properties of the individual components of a mixture, and as defined by Eq. (l), it is readily shown that in a coexisting gas-liquid system the rnol fraction concentrations of the individual components in the gas phase, y,, and those in the liquid phase, x,, are given by the expressions: where the nj are the corresponding rnol fraction concentrations in the composite system, and ng is the mol fraction of the whole which is in the gas phase. The basic unknown in Eq. (2) is n,: which gives the gross separation between the gas and liquid phases. This may be determined in principle by imposing the requirement that the sums of the mol fractions in both the gas and liquid phases are unity, i.e. by the equations: The solution of the equivalent Eqs. (3) lying between 0 and 1, when inserted into Eqs. (2), provides a complete description of the compositions of the coexisting gas and liquid phases. While the Eqs. (3) are essentially equivalent to polynomial equations, such transformations are of little value when dealing with multicomponent sys-

Jan 1, 1949

By L. L. Newman

As soon as the Congress recognized the alarming rate at which our domestic oil resources were being depleted during the war, it took action to step up the rate of research and development which the Bureau of Mines had been conducting for several years on the production of synthetic liquid fuels from coals. Under Public Law 290, approved April 5, 1944, funds were authorized for the Bureau to proceed with research, development, design and construction of demonstration plants for the hydrogenation of coal, the synthesis of oil from carbon monoxide and hydrogen, and the distillation of oil from shale. During the latter part of 1944, when it became evident that the collapse of Germany was near, a Technical Oil Mission was organized to study the German techniques of synthetic oil production. Since the cost of hydrogen or synthesis gas is one of the major factors of expense in the operation of hydrogenation or synthesis gas processes, the Bureau of Mines considered it of prime importance to include on the mission gas engineers whose instructions were to examine closely the methods employed by the Germans in solving the problem of providing low-cost hydrogen or synthesis gas for their very extensive operations on synthetic liquid fuels. The Solid Fuels Mission and the Utilities Mission, as well as the Army and Navy Missions, also included teams for the study of German gas production. Although their objectives naturally differed from those of the Technical Oil Mission and from each other, it was recognized that there was considerable overlapping of their fields of investigation. Duplication of effort, however, was largely avoided through the close cooperation between the group leaders of these missions. For example, although I went to Europe as a member of the Technical Oil Mission, my first Gcrman assignment was actually made by Dr. Harry F. Yancey, leader of the Solid Fuels Mission— to investigate the brown-coal gasification methods in central Germany. The art of gasification in the United States and England, and to a large extent in the proximity of the coking-coal regions of Germany and the rest of continental Europe, depends essentially on two stages of operation; namely, carbonization and intermittent water-gas generation. As far as the United States is concerned, complete gasification in a single stage of operation is rarely practiced, except in gas-producer operations where the product is a relatively lean gas consumed close to the point of manufacture, and for water-gas production with anthracite as a generator fuel. Complete gasification of bituminous coal has been the subject of numerous investigations. Many relatively simple modifications of the water-gas generator have been tried to permit the direct gasification of low-cost bituminous coal instead of high-cost coke and anthracite for the production of water gas. Although varying degrees of Success have been achieved and the water gas produced generally has been higher in

Jan 1, 1947