Search Documents

By E. M. Wise

THE properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. GENERAL REQUIREMENTS In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should be good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depilatories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 lb. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800° and 1200° C.

Jan 1, 1928

By Donald L. Ball

The equilibrium of boron nitride, gaseous nitrogen, and solute boron was investigated in Fe, Fe-C, and Fe-Si rnelts by the Sieverts technique. The free ellergy of dissociation of boron nitride, involving -the implied standard states, was evaluated in the range 1400" to 1600°C as: ?Fo = 38,000 - 23.5T, cal ber mole The solute-solute interaction coefficients eBB, ecB , and eg were determined as 0.058, 0.22, and 0.078, respectively. BORON is an important ingredient in some types of steel and cast iron. It was employed at a particularly high level, 0.01 wt pet, in the as-cast malleable iron "CentraSteel".1 In this material, the boron concentration was critical in order to assure graphite, and avoid primary cementite, in the as-cast structure. One possible function of the boron in this alloy was the nucleation of graphite through the agency of boron nitride, which, conceivably, precipitated from the melt during cooling. A research program was instituted to assess the validity of this proposed mechanism. The first undertaking, reported here, was a determination of the thermodynamic possibility of boron nitride precipitation. Data available in the literature on the activity coefficient of solute boron in iron-base melts are inadequate for the present purpose. They will be reviewed briefly, however, so that comparison can be made, when

Jan 1, 1968

By Charles O. Burgess

The improvement in the quality of cast iron by means of alloy additions has been a metallurgical accomplishment of recent years. Work in this field has shown that chromium is one of the most effective of such additions but, in general, the influence of chromium has been studied only in connection with other alloying additions, with irons other than foundry irons, or with relatively high percentages of chromium. The present study was initiated for the purpose of determining the influence of small additions of chromium (0.25 to 1.00 per cent) on the quality and resultant properties of cast irons of various foundry grades. The effect of small chromium additions on cast iron was investigated with particular reference to casting characteristics, hardness vs. section, strength, machinability, heat resistance and structure. Material Tested Three separate types of cast iron were investigated as to the effect of small chromium additions. The first series of these irons was prepared from remelted foundry cast iron at the Union Carbide and Carbon Research Laboratories, and the other two series consisted of cupola melts made under usual operating conditions. The first series was made by melting 30-lb. charges of foundry scrap iron containing 2.86 per cent carbon, 2.72 silicon, 0.50 manganese, 0.062 sulfur and 0.794 phosphorus in a carbon resistance furnace. The chromium was added as high-carbon ferrochrome just before pouring. The irons were cast at approximately 1250" C. (2282" F.). The analysis and physical properties of these irons are given in Table 1, test 1. The second set of cast irons was made in a cupola in accordance with normal practice, the charge containing approximately 42 per cent steel scrap and the chromium additions being made to the ladle. Analysis and tests of these heats are shown in Table 1, test 2. A small amount of copper was present in heat C of this series. Further data on the effect of chromium on strength were obtained from a third series of 13 cupola heats containing from 0.06 to 0.50 per cent chromium and made without steel additions. The heats were all

Jan 1, 1933

Discussions of the papers of DORSET A. LYON and SAMUEL S. ARENTZ, RICHARD D. DIVINE, H. A. WENTWORTH, and S. E. BRETHERTON, presented at the Salt Lake meeting August, 1914, and printed in Bulletins Nos. 91 and 92, July and August, 1914. GEORGE W. RITER, Salt Lake City, Utah.-We have every reason to believe that oil flotation Will soon come into general use as a final guard against slimes losses in concentrating mills, not only in the case of zinc ores, but also in the case of other semi-precious ores. It also promises much as a primary process for the concentration of minerals that are not adapted to gravity methods. Moreover, modifications of the process involving selective or preferential flotation are gradually becoming understood, and will make it possible to eliminate pyrite and other minerals occurring as undesirable impurities in zinc concentrates. And what perhaps is of equal importance, further modifications promise an effective method of separating zinc blende from ores that are chiefly valuable for copper, lead, anti precious metals, thereby making an asset out of zinc which has heretofore been a liability. The tendency of certain pulverized minerals to float on water, especially after having been in contact with grease, has been known to mill-men for a long time, and was formerly something to be deplored and to be striven against. All at once, this tendency has become a saving grace; and now, like tardy converts to a new faith, we are zealous advocates of something we once despised. I was once employed at a mine in the Tintic mining district of Utah¬the old Eureka Hill property-where ores that were too low in value to Warrant being sent to copper or lead smelters were treated in a combination mill. The ores contained gold, silver, lead, copper, zinc, manganese, arsenic, etc., in varying quantities and in varying mineral forms, mingled in a quartz and calcite gangue. The material was stamped fine and then concentrated on Frue vanners so as to make a smelting concentrate, after which the tailings were thickened and treated in amalgamating pans for the recovery of non-concentratable precious metals. In the amalgamating pans, under the influence of heat and agitation, a dark greasy froth or scum sometimes formed on the surface of the ore mixture. This froth or scum was composed mainly of mineral sulphides, and its occurrence might have meant only casual losses in the previous concentration, except that the phenomenon was accompanied by faulty amalgamation of the precious metals and by excessive losses in the mill tailings. Grease and oil, present by accident, were the cause of the trouble.

Jan 11, 1914

By Thomas Cox

This paper makes no claim to any new idea; it simply reviews the Treasury Department Regulations pertaining to the practical application of depreciation and depletion and other allowances governing taxation of oil and gas properties. Other methods may be existent, but as they may not conform to the legal status they must be discarded. In complying with the present laws governing the industry with regard to taxation and the allowable deductions therefrom, the following considerations are essential: Depletion, depreciation, amortization, other allowances, and items not, deductible. It is definitely understood that depletion is the loss or exhaustion sustained in the continuous operating of an oil and gas property, and that each unit of oil or gas taken out reduces the value of the property until its final exhaustion. Depletion applies only to the natural deposits of oil and gas due to their removal in the course of exploitation of any property. Depreciation is defined to cover the waste of assets due to exhaustion, wear and tear, and obsolescence of the physical property, and is separate and distinct from depletion; its allowance is that amount which should be set aside for the taxable year in such sums as for the useful life of the property will suffice to repay its original cost—or its value as of Mar. 1, 1913, if acquired by the taxpayer before that date—less the salvage value at the end of such useful life. Amortization is allowed for such facilities as were built or acquired on or after Apr. 6, 1917, for the production of articles contributing to the prosecution of the war and, in the case of vessels, those built and acquired after that date. The amount to be extinguished, in general, is the excess of the unextinguished or unrecovered cost of the property over its maximum value under stable post-war conditions. Claims for amortization must be unmistakably differentiated in the returns from all other claims of depreciation. The taxpayer is also required to furnish full information with the claims for amortization to the full satisfaction of the Commissioner. Further reference is directed to the specific rules and regulations for making these claims.

Jan 1, 1921

By J. B. Clark, A. S. Yue

PfANN1 has shown that when a cylinder of molten binary alloy freezes directionally, the solute distribution can be described analytically by cg=k(l-g)k-1 [1] in which Cg is the solute concentration in the solid at the point where a fraction g of the original liquid has frozen and Co is the initial solute concentration. The term k is the effective distribution coefficient of the solute and is defined as the ratio Cx/CL where Cl is the solute concentration in the main body of the liquid. Both the slope and the intercept at -log (1 - g) = 0 of a logarithmic plot of Eq. [I.] provide a measure of k. Under conditions of freezing where diffusion in the solid is negligible and the solute concentration in the liquid is uniform, the effective distribution coefficient k, derived as above, is equal to the equilibrium distribution coefficient taken from the phase diagram. However, under ordinary freezing conditions, even though solid-state diffusion is negligible, the solute rejected from the freezing solid does not have sufficient time to diffuse uniformly throughout the main body of the liquid. A concentration gradient is formed in a boundary layer in front of the advancing solid-liquid interface as pointed out by Rutter and Chalmers.' Thus, under these conditions, the concentration of the freezing liquid in the boundary layer is higher than that predicted from the equilibrium phase diagram and consequently the effective distribution coefficient k, obtained from directional freezing experiments, is larger than the equilibrium distribution coefficient. The symbol k will designate the effective distribution coefficient in the discussion which follows. In this paper, the determination of the effective distribution coefficient is demonstrated for several dilute binary alloys and a polynary magnesium alloy. The effect of freezing rate on the value of the derived k is presented in detail. An example for the calculation of the solidus in a dilute binary solution using the experimentally determined effective distribution coefficient is given. MATERIALS STUDIED Binary magnesium alloys of copper, nickel, and zinc containing approximately 0.10 wt pct solute and a polynary alloy containing approximately 0.10 wt pct each of several elements were selected for study. The spectrographic analyses of these alloys are given in Table I. The analyses are believed accurate to within +5 pct of the stated value. EXPERIMENTAL PROCEDURE Extruded rods of the alloys, 3/8 in. in diam and 11 in. long were used for directional freezing studies. The alloy rods were melted horizontally in a high-purity graphite boat by a Nichrome-wound tube furnace which moved parallel to the length of the rod. The boat was supported inside a Vycor tube suitably connected to provide a protective atmosphere of dry SO2. For an experimental run, the following procedure was used. The alloy rod was cleaned in dilute HNO, and dried. The graphite boat containing the alloy rod was placed within the Vycor tube and the tube connected to the gas train' The 'ystem was purged for 20 min with dry argon and then a flow of dried SO, was maintained for the duration of the run. The movable furnace was positioned and either all or a desired portion of the alloy rod was melted. After attainment of steady-state temperature gradients the molten bar was solidified from one end to the other at a controlled rate by pulling the furnace along the length of the bar at the desired speed. At the conclusion of the run, the directionally frozen alloy rod was analyzed spectrographically at 1 1/4-in. intervals.

Jan 1, 1961

By Gerald Sherman

In the southern field of the anthracite region of Pennsylvania, many of the coal seams dip at angles of 40" to 50" from the horizontal. For transportation purposes, "tunnels" are driven across the coal measures and, occasionally, "rock gangways," beside the seams and parallel with them. The use of gangways driven in country rock appears to be increasing, as they avoid the maintenance of long gangways in coal, which eventually are driven to the colliery boundaries, and permit mining from a number of intermediate blocks without interference. The rock consists of slates or sandstones of moderate hardness, which may range into very hard, highly siliceous, fine-grained conglomerates. In this distinctly bedded formation, the direction of the heading, whether parallel with or across the structure, makes it necessary to distribute the drill holes in a different pattern to break the ground, but does not change loading conditions. In 1932, practically all the mucking was done by hand, and it was the established custom to use four men on two drills for drilling and breaking the ground, and five for loading it out. A driver and mule was needed in addition, to assemble the rock cars at a siding or branching track in the rear, pending their final disposal. This might occupy the driver's whole time, or if the length of haul were short, he might be able to do other useful work. It was thought possible in 1932 to reduce the cost of driving such headings in rock by mechanical loading, and to investigate this subject a scraper loader was used in a section of tunnel then being driven. Operations while driving 195 ft. of this tunnel using a scraper loader were carefully observed. Time studies were made of the loading, and records made of the routine of breaking ground, but not in such detail. Tunnels or gangways in the colliery are 7 ft. high above the rails, by 10 ft. wide, which requires a minimum of 8 ft. in height, broken to allow for rails and ties. This cross section is of sufficient size to permit the use of any one of several types of power loaders, but for this demonstration it was found most convenient to use a scraper loader.

Jan 1, 1937

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials. Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant. These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements. Construction of the plant, having originally a design capacity of 7000 bbl. of cement per day, was started in June 1939, and the first clinker was ground on the following Christmas Day. At present the capacity is about 12,000 bbl. of finished cement per 24 hr., most of the production being low-heat cement. [t] About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output. Occasionally iron oxide is added to the clay to obtain the desired composition. This, together with the gypsum, is purchased from outside sources. Up to the present time, the corporation has produced low-heat, normal, moderate-heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements. Most of the present production is for Shasta Dam, near Redding, Calif., the total demand being 5.800,000 bbl. of cement. Following are some of the cement require¬ments of the Shasta Dam specifications: [PER CEN'I Chemical composition: Loss in ignition2.25 Insoluble residue0.75 S032.25 M905.00 Uncombined lime in clinker (CaO)T.25 Percentage of iron oxide to alumina ratio1.5 Compound composition: Tricalcium silicate (3CaO.Si02)Not more than 35 Dicalcium silicate (2CaO.Si02)Not less than 40 and not more than 6,5 Tricalcium aluminate (3CaO.Al203)Not more than 7 Tetracalcium aluminoferrite (4CaO.A1203.Fe203) Not more than 20 Fineness:] The average specific surface in the bin sampled shall be not less than 1800 sq. cm. per gram and no individual sample less than 1600 sq. centimeters. Compressive strength: The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2.75 parts fine testing sand, by weight, shall be equal to or greater than the following: [ ]

Jan 1, 1941

By Nicholas J. Grant, Raymond E. Cairns

A high-purity chromium, made by solid-state extrusion, and a series of molten, extruded, dilute alloys containing carbon, oxygen, nitrogen, and sulfur were studied to establish the effects of composition, cooling rate, grain size, strain rate, and prior strain on the transition temperature for brittle THE transition from ductile to brittle fracture with decreasing temperature remains of extreme interest especially among the refractory metals, such as tungsten, molybdenum, and chromium, which have relatively high transition temperatures. Fracture, yield stress, and hardness. Tension tests at a strain rate of 0.015 per min were generally utilized. Results are interpreted in terms of the quantity of each element retained in solid solution. Of these elements, chromium has been studied the least, but deserves additional attention because of its superior oxidation resistance for high-temperature use. In the past, impurity elements which have received attention are carbon, nitrogen, oxygen, and sulfur;'-' of these, nitrogen has usually been considered to be the most detrimental. Unfortunately, because of different levels of both specific and total impurity content, and because of the many different test and evaluation techniques used, a clear, definitive picture of brittle fracture in chromium has not been forthcoming. However, many

Jan 1, 1964

By J. Rogers, H. F. A. Hergt, K. L. Sutherland

In 1938 Ralston4 reviewed the many attempts to find a satisfactory collector for the separation of cassiterite from its ores and in 1944 Dean and Ambrose2 summarized some further attempts. Generally, soaps and amines are effective but nonselective collectors. We have discovered that reagents containing either the polar group — SO4- or — SO3- are excellent collectors for cassiterite and promise to be selective. The response to these reagents of cassiterite and of minerals commonly associated with it was studied, using the captive-bubble technique. Using these fundamental data, the practicability of separation and concentration of tin was investigated by flotation tests in a 2000-gram Denver cell. Experimental Methods Reagents All inorganic reagents were of Analar grade. The preparation and purification of sodium cetyl sulphate, cetyl trimethyl-ammonium bromide, laurylamine and cetylamine have been previously described.5 The other collectors were commercial surface-active agents, which were used without purification. Tests Captive-bubble Tests and Cylinder Flotation Tests have been previously de- scribed.5,10 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible, by a cross, and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, and the experimental results are indicated by a square. The curves show the limits of composition of solutions in which flotation in a cell would be possible but many factors other than those considered in these the determine recovery and grade of a given mineral in practice. Flotation Tests in 500 and 2000-gram Denver SUbmachines,—Melboume tap water, containing 12 parts calcium, 6 parts

Jan 1, 1947

By M. A. Dayananda, R. E. Grace, P. F. Kirsch

Ternary diffusion experiments were carried out at 750°C with vapor-solid diffusion couples in single-phase copper-rich Cu-Zn-Sn alloys. The Philibert-Guy method was used to calculate intrinsic diffusion coefficients at compositions corresponding to the plane of inert markers imbedded in the diffusion couples. Inter diffusion coefficients were determined at common composition points of intersecting diffusion paths. Intevdiffusion coefficients were also obtained at compositions corresponding to maxima in the tin concentration pvofiles Relations between the interdiffusion coefficients and the expansion of vapor-solid diffusion couples are described in detail. Such relations permit the calculation of constant interdiffusion coefficients in binary couples from expansion data directly. In ternary couples expansion data provide an additional constraint on the interdiffusion coefficzents. ThE phenomenological analysis of diffusion in ternary solid solutions has been developed extensively, and various approaches taken in the determination of diffusion coefficients have been reviewed recently by Guy et al.' Finite,' semi-infinite,3 and infinite4 diffusion couples have been used in studies of ternary diffusion, but most of the work has been done with infinite diffusion couples. Semi-infinite diffusion couples3 (vapor-solid couples) have been used to determine both intrinsic and interdiffusion coefficients in the Cu-Zn-Mn system, in which two diffusing species, zinc and manganese, were supplied from the vapor phase. If only one component has a sufficiently high vapor pressure to be supplied from a vapor source, vapor-solid diffusion couples may still be used. In this case the boundary conditions at the gas/solid interface may be governed by partial equilibria rather than by virtually complete equilibrium between the phases. In the present work diffusion measurements were carried out at 750°C with vapor-solid couples of Cu-Zn-Sn alloys. Only zinc was transported between the vapor source and the diffusion disks, because the vapor pressures of both copper and tin are at least 108 lower than that of zinc. Both intrinsic and interdiffusion measurements were made at several compositions. A secondary objective was to relate expansion of the diffusion couples with the interdiffusion process. Such measurements for binary couples yield average values of the interdiffusion coefficients over composition increments. In ternary diffusion couples ex- pansion data provide an additional constraint on the interdiffusion coefficients. COMPOSITION-DEPENDENT INTRINSIC AND INTERDIFFUSION COEFFICIENTS As shown by Philibert and GUy5 the determination of intrinsic diffusion coefficients in a ternary system requires two independent diffusion couples containing marker planes with identical composition. In the case of vapor-solid couples such a requirement torresponds to two couples set up with the same vapor source exposed to two diffusion disks of different composition. Inert markers placed initially on the disk surfaces become imbedded during diffusion. If the pair of couples exhibits appreciable marker burial with marker planes of virtually the same composition, the intrinsic diffusion coefficient may be evaluated at the composition of the marker planes. Fig. 1 is a schematic diagram of the concentration of of a Cu-Zn-Sn ternary vapor-solid couple after diffusion of zinc from a vapor source into a binary Cu-Sn alloy. The areas, Ai correspond to the cumulative intrinsic fluxes of the three diffusing species across the marker plane:5 where Ji is the intrinsic flux of component i, t is the diffusion time, and D3i are the intrinsic diffusion coefficients. For the determination of interdiffusion coefficients a pair of diffusion couples with intersecting diffusion paths is needed. At the composition point of intersection (C1, C2) the coefficients are evaluated from the equation:3

Jan 1, 1969

By W. D. Forgeng, R. E. Grace

The rate of copper corrosion in liquid lead was studied as a function of flow rate and temperature in a closed isothermal loop system between 350" and 500°C. Kinetic data were interpreted with the Nernst-Brunner equation and the Chilton-Colbum mass transfer analogy to heat transfer. Over the range of temperatures and flow rates employed the solution rate constant varied from 2 x 10-3 to 20 x 10-3 cm per sec. The rate constant was found to vary with the 0.76 power of the Reynolds number in the range 7500 < Re < 40,000. The results of this investigation indicate that the Cu-Pb corrosion process is controlled largely by diffusion across a boundary layer. particularly at the higher temperatures. The effective boundary layer for diffusion is found to be approximately three to four times smaller than the momentum boundary layer. CORROSION by liquid metals has long been a problem during melting, static containment, and casting. Recently, considerable emphasis has been placed on the understanding of liquid metal corrosion mechanisms in an effort to prevent mass transfer and eventual failure in liquid metal heat exchangers and in liquid-metal-fueled nuclear reactors. The present investigation was conducted to determine the relationships which exist between corrosion kinetics and hydrodynamic conditions in an isothermal loop containing a simple liquid metal-solid metal corrosion system. The Cu-Pb system was chosen for its simplicity and ease in handling. Previous isothermal Cu-Pb corrosion studies1-3 have been conducted in both static and dynamic systems but not under conditions which allow easy "scale-up" to engineering systems, such as liquid metal heat exchangers. On the other hand, most liquid metal loops which have been used to evaluate mass transfer rates4 have been driven with temperature gradients under conditions of natural convection and unknown flow rates. The primary contributions of this research are twofold: 1) to evaluate the design of a simple isothermal loop corrosion system and 2) to investigate liquid metal corrosion behavior under well-defined hydrodynamic conditions. MATERIALS AND EXPERIMENTAL WORK The apparatus used to measure the Cu-Pb corrosion rates is shown schematically in Fig. 1. The loop system consisted of 1) a reservoir made of Type 316 stainless steel containing a centrifugal pump and 2) stainless-steel tubing containing a removable copper test section. The copper test section was OFHC hard-drawn tubing, 11.0 0.05 cm in length and 0.775 ±0.005 cm ID. A Type 316 stainless-steel venturi meter* was inserted in place of the copper test sec- tion in order to determine the lead velocity as a function of pump speed at each temperature. The Cu-Pb system was chosen for this study because the solubility of copper in liquid lead is large enough to measure accurately but small enough that the diameter of the copper tubing was not changed significantly by corrosion. There are no intermediate phases formed in the system, and the solid solubility of lead in copper is vanishingly small so that back-diffusion cannot occur. Molten lead (corroding grade; 99.94+ pct Pb, 0.0015 max pct Cu) was charged from an auxiliary melting furnace into the system under an argon cover to minimize oxidation. The lead was then maintained at constant temperature by a stirred molten salt bath in which the loop was immersed to a depth just above the lead level in the reservoir, Fig. 1. The total volume of lead in the system was 320 2 cu cm.

Jan 1, 1969

By P. A. Beck, A. Merlini

Quantitative texture determinations were made for rolled and for rolled and annealed strips of 3, 6, and 10 pct Zn brasses. The main components of the rolling texture gradually shift over a wide composition range from the orientation characteristic of copper to that of 70-30 brass. At least the main features of the corresponding gradual changes in the annealing texture may be accounted for qualitatively on the basis of the oriented growth theory of annealing textures. All the oriented nucleation-type theories are notably less successful in accounting for the observed textures. EARLIER investigations by von Goeler and Sachs,&apos; Dahl and Pawlek,&apos; and Brick, Martin, and Angier" suggested that the annealing texture of copper is more sensitive to the addition of solute elements than the rolling texture. It was reported3 that the cube texture changes over into a brass-type recrys-tallization texture on addition of about 1 pct Zn, while the deformation texture changes only at about 5 pct Zn. Such behavior would be difficult to reconcile with any theory of annealing texture formation that relates the annealing texture to the deformation texture. In particular, the oriented growth theory of the cube texture" is based on a certain orientation relationship between the cube texture and the main components of the deformation texture which could not be reconciled with the reported behavior of low brasses. It was, therefore, of interest to re-examine these textures by means of the quantitative methods now available. The deformation and annealing textures of rolled a brasses with approximately 3, 6, and 10 pct Zn have been determined in terms of (111) and (200) pole figures. Experimental Methods The chemical analyses of the Cu-Zn alloys of commercial purity used in the present work are given in Table I. Chill-cast bars of the tabulated compositions were rolled and annealed according to the following schedule: I—rolling from 1.2 to 1.02 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 2— rolling from 1.02 to 0.867 in. thickness, 15 pct reduction area, annealing 15 min at 450°C; 3—rolling from 0.867 to 0.600 in. thickness, 31 pct reduction area, annealing 2 hr at 540°C; 4—rolling from 0.600 to 0.400 in. thickness, 33 pct reduction area, annealing 2 hr at 480°C. In the final straight rolling of 96.25 pct reduction area, the strips were reversed end to end after each pass. The final annealing temperature was determined for each alloy by annealing specimens of the cold-rolled strips in salt bath for 5 min at varying temperatures. The results of the hardness measurements are given in Fig. 1, where the final annealing temperature used for each alloy in determining the annealing texture is indicated by a cross.

Jan 1, 1956

By E. A. Gulbransen, J. W. Hickman

INTRODUCTION DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may occur to such a degree that oxides may form in the body of the film and on the outer surface which are different from those that would normally form if the additional elements were not present. The use of transmisson electron diffraction may aid us in interpreting these phenomena. Up to the present time all of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physical state of the alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the removal of carbon by oxygen in a decarburization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with

Jan 1, 1948

By C. D. Ramsden

During the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Purchase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by salvaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a considerable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been rebuilding locomotive wheels for several years with automatic open are-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under-flux are-welding process for wheel rebuilding, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company&apos;s maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company&apos;s heavy locomotives have three sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. Open Arc Welding With the open arc process, a set of wheels could be rebuilt for about 40 pet of the cost&apos; of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or positioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1947

By Cyril Stanley Smith, Earl W. Palmer

A complete discussion of the literature on the subject of the influence of copper on iron and steel will be published elsewhere.&apos; The present paper is concerned especially with the precipitation-hardening of copper steels, and brief mention will be made here only of the work of Kin-near,2,3 Nehl4 and Buchholtz and Koster,5 who alone have studied this phase of the subject. Kinnear found that normalized low-carbon steel castings containing about 1.0 per cent copper on drawing at temperatures in the neighborhood of 530" C. (1000" F.) increased in tensile strength and yield point, with little decrease in ductility. The maximum effect was obtained with about 0.9 to 1.0 per cent copper, and when the copper exceeded 3 per cent no improvement occurred on reheating. Kinnear did not study the effect of time of reheating—an all important factor where precipitation is concerned. Neh1,6 who apparently was unaware of Kinnear&apos;s work, recognized the change as due to precipitation and studied the interdependence of time and temperature of reheating, the temperature of the initial solution heat treatment, and the speed of cooling necessary to retain the bulk of the copper in supersaturated solution and to give an increase in hardness and tensile strength on reheating. Nehl found that if the final rolling or forging temperatures exceeded 700" C. (1300" F.) it was not necessary even to normalize the steel, but full precipitation occurred on merely reheating the forged or rolled shapes at 500" C. (930" F.). Buchholtz and Koster7 studied in detail the precipitation-hardening of a mild steel containing 1.0 per cent copper and 0.5 per cent chromium. From data on the electrical and magnetic properties of copper steels, they drew the portion of the equilibrium diagram in Fig. 1, assuming the

Jan 1, 1933

By W. R. Seyfried

THE -problem of extracting alumina from clay and low-grade bauxites has been the subject of considerable interest for some time. The basic reason, of course, lies in the fact that known reserves of high-grade bauxite are not inexhaustible and that the present commercial process cannot successfully cope with low-grade bauxites or clay. Ultimately it may be necessary to use these poorer raw materials for all commercial operations, An unprecedented demand for aluminum during the war emergency and the constantly threatened shortage of imported bauxite caused the United States Government to take an active role in this problem. Through the National Academy of Sciences, the War Production Board and the Defense Plant Corporation, it investigated processes and finally selected four to be used in the construction and operation of four experimental plants. Each plant was to be designed in such a way as to facilitate its incorporation into a larger commercial plant should the need arise. The Chemical Construction Corporation process, or "Chemico" ammonium sulphate process as it is better known, was one of the four selected. The extensive literature and patents on record before the war generally follow one of two process-types depending upon the extracting reagent used. One group uses an acid reagent, the other an alkali. The Chemico process uses an acid reagent. For those interested in other processes described in literature, there is a short bibliography at the end of this paper, The basic steps of all acid extraction processes are: (I) to make the aluminum silicates acid soluble, (2) to separate the released alumina from impurities and insoluble gangue, and (3) to recover the reaent for re-use. THE PROCESS AS PLANNED In April 1941, a group of chemists and engineers of the Chemical Construction Corp, became interested in the problem of extracting alumina from clays and low-grade bauxites and, under the leadership of Mr. Blakeslee Barnes, Vice President and General Manager of the Company, first drafted a process in July of that year-five months prior to Pearl Harbor. The work continued in our research laboratories and with a small pilot plant, By June 1943, the work had progressed to a point where it was possible to apply for a patent on the process which was U.S. patent 2,405,426, granted August 6, 1946. Immediately prior to the development of the Salem plant, the process was envisaged to be as follows: I. The first step was to make the aluminum silicates acid soluble. It was planned: (a) Clay or low-grade bauxite would be roasted at 700 to 800°C (1292° to 1492°F). (b) The roasted ore would then be leached .with hot aqueous ammonium bisulphate to form a slurry. In this way the

Jan 1, 1948

By John Mark Patek

Knowledge of the relative floatability of silicate minerals is increasing in importance as flotation is being applied to the concentration of nonsulfides. Many silicates are in themselves commercial products amenable to concentration by flotation. Moreover, the selective flotation of other nonsulfide minerals, such as cassiterite, depends largely upon the floatability of associated gangue silicates. Differences in floatability existing between the various silicates have not- been sufficiently appreciated; for example, the feldspars that differ greatly in floatability have generally been merely treated as "feldspar." It was the purpose of the work described in this paper to determine by experiment the differences in floatability between silicates; to investigate the causes for such differences, and to discover a means of predetermining approximate floatability without the necessity of experimentation. Determining Floatability The relative floatability of 20 silicates so selected as to represent all of the more common silicate types1 was obtained by flotation tests enumerated in Table 1. The mineral to be floated was crushed dry on a steel plate, and screened repeatedly during crushing through an 80-mesh screen in order to produce a sand with all grains as close to 80 mesh as possible. The sand was placed in dilute (6N) hydrochloric acid until free of soluble foreign material, and then washed with tap water about ten times in order to remove both acid and fines. The resultant product, which averaged 82 per cent plus 200 mesh, was floated in 50-gram charges in a 50-gram Denver celluloid flotation machine with 0.008 gram of terpineol, and from 0.01 to 0.05 gram of oleic acid in a solution acidified with sulfuric acid. The degree of separation of one mineral from another was determined by counting under a nlicroscope the grains of each mineral, both in the concentrate and in the tailings, and comparing their relative abundance in each. Unless the comparison showed a decided difference in amount,

Jan 1, 1935

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytical expressions derived previously are used to describe quantitatively effects on macrosegregation of some solidification and mold design variables. Al-4.5 pct Cu alloy is used as example. It is shown that abrupt changes in heat transfer rate result in solute-rich or solute-poor "bands". Severe solute-rich bands accowzpany "reheating" that can result, for example, from abrupt formation of an air gap at a mold-metal interface. With planar isotherms, solute-poor regions also result from reduction in cross section through which fluid flow to feed shrinkage takes place. It is suggested that the negative "cone" of segregation often found at the base of large ingots results from this reduction in cross section for feeding. Consideration is given to the positive and negative segregation to be expected in laboratory ingots in association with changes in ingot cross section. Under-riser positive segregation is considered and it is concluded this segregation results when vertical temperature gradient is low in the region of the riser; the segregation is accentuated by the temperature gradient reversal which can occur in inadequately insulated risers ("&apos;hot tops"). Finally it is shown for Al-4.5 pct Cu alloy that the assumption of constant k and p in analytic solutions gives calculated results close to those obtained for the case of ziariable k and 0. A basic "local solute redistribution equation" was derived earlier&apos; for calculation of macrosegregation resulting from flow of solute-rich liquid to feed solidification shrinkage, thermal contraction, and/or other contractions occurring during solidification. This expression relates fraction liquid, g~, to liquid composition, CL, at a given position x, y, z, in a solidifying Eq. [I] is for the general case of three-dimensional heat and fluid flow assuming constant solid (but not necessarily liquid) density during solidification, negligible net solute change from diffusion, and no pore formation. In this paper we first demonstrate application of this equation for calculation of macrosegregation in several examples involving one-dimensional heat and fluid flow. Specifically considered are examples in which segregation results from sudden changes in heat flow conditions. Next, Eq. [I] is used to describe segregation in examples where isotherms remain planar but where fluid flow is no longer one-dimensional. Application of this expression illustrates the type of segregation to be expected in unidirectionally solidified ingots of gradually or abruptly varying cross section. For segregation calculations, A1-4.5 pct Cu alloy is employed with constant k and p Vz = 0.172, 4 = 0.055), eutectic composition (CE = 33 pct Cu). In all examples, fraction eutectic is neglected in velocity calculations; this was previously shown to introduce little error.&apos; A linear distribution of fraction liquid in the liquid-solid zone is assumed. In a concluding section it is shown that the assumption employed of constant k and /3 gives results close to those obtained when the actual (variable) values of k and 0 are employed.

Jan 1, 1969

By Roswell P. Angier, Herbert S. Kalish, Henry H. Hausner

POWDER metallurgical methods as applied to zirconium are of great interest because they permit not only the fabrication of parts directly to shape with a minimum loss of material but also the utilization of scrap, and the metal may be processed at temperatures well below the melting point. There are two difficulties involved in the melting of zirconium: 1—High vacuum is necessary for melting, and 2—zirconium reduces nearly all oxides so that it is difficult to find a suitable crucible material. The purest material, zirconium crystal bar, is expensive, and the methods of subsequent fabrication are limited. Cold rolling or extrusion of zirconium crystal bar is suitable for making certain shaped parts, but where melting is involved, the purity of the metal is invariably decreased, and a method of casting to a definite shape does not seem to be feasible. Where it is necessary to hot roll, zirconium must be covered with a steel or copper jacket to protect it from the air. This is necessarily a costly operation. Where annealing of zirconium is necessary it must be conducted in a high vacuum. In an investigation of powder metallurgical methods for zirconium, the zirconium powder used should be characterized by the following properties: 1— Highest degree of purity, 2—uniformity in particle shape and particle size distribution, 3—low compression ratio, and 4—satisfactory strength of the compacted powder (green strength). Zirconium powders have been made by two methods: By the reduction of zirconium tetrachloride (ZrC1,) with sodium,2&apos; *•B "nd by the reduction of zirconium oxide with calcium and calcium chloride." The first method represents one of the earliest attempts to make pure zirconium metal, and the sintered product from this powder is extremely brittle. The second method of making zirconium powder is far more successful, but the powder made in this way has an extremely low apparent density and, therefore, a high compression ratio which makes it difficult to use it for powder metallurgical purposes. For these reasons the above-mentioned zirconium powders were not used in this investigation. To obtain sintered zirconium compacts of highest &apos;purity and good ductility, it was first necessary to produce a suitable powder. Pure zirconium has been made chiefly by two methods. The iodide method, from which the product is "crystal bar" zirconium, was developed first.&apos;." By this purification process very soft, pure, and ductile zirconium metal can be produced. The second method, developed by the U. S. Bureau of Mines, is the reduction of zirconium chloride with magnesium." The sponge zirconium thus produced is also soft, pure, and ductile.

Jan 1, 1952