Search Documents

By A. S. Malicsi, R. J. Lipp, I. Iwasaki

A loch-grade copper-nickel deposit, with an estimated 4.6 Gt (5 billion st) and average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase, and biotite. It u estimated that flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 Mt/a (22 million stpy). The flotation tailings, having already been ground, warrant a closer examination for recovery and use of potential byproducts. Residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. Concentration methods for recovering and purifying individual byproduct minerals were investigated. From their chemical, physical, and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1985

By J. R. Thoenen

THE preper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical controversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of underground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute Transactions, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in Mining and Metallurgy in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical: From his experience of many years in the study and operation of both underground and surface metal and nonmetallic mines, the writer does

Jan 1, 1942

By J. F. Kemp

CONTENTS. [ ] I. INTRODUCTION. 1. Situation.-From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway, which connects Monterey with Tampico, follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares, and from Linares one can see far away to the southeast the peaks of another group of mountains

Jan 1, 1913

By Harrison R. Cooper

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application knowledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By Albert J. Phillip

Jan 1, 1947

Some years ago it was my good fortune to inspect some coal properties in Germany, and the most striking impression I received on my trip was that in that country every one in the coal industry, miners and operators, was proud of the fact-not apologetic about it-and that industrially coal was looked upon as a King. The explanation, of course, was that at least 90 per cent of the entire mineral value produced in Germany was from coal, and that it was the very foundation of the nation's industrial life. The feeling was so different from that existing in the United States among those engaged in producing coal that it made a profound impression on me, and many times since then I have speculated about the reasons for the difference in opinion in the two countries. Here, of course, our units are much smaller and more numerous, there is not so large a proportion of technically trained men, and we have the American trait of depreciating the things we do at home; but among those not actively

Jan 1, 1935

By Hugh J. Leach, J. C. Van de Water

In open pit mining, as in other industries, it has I become necessary to improve operating efficiency in order to combat higher labor and supply costs. Moreover, orebodies are becoming leaner, pits are getting deeper, stripping ratios are increasing, and hauls are getting longer. There has been a steady increase in size, speed of operation, and reliability of the various machines involved in breaking, loading, and hauling ore. Changes have seldom been radical but are rather the result of steady improvement. Drilling: Notable advances have been made in the use of rotary drills and air powered percussion drills for blasthole drilling. Several hundred of these machines are now in use as replacements for churn drills in softer rocks such as limestone and shale. Their application to hard rocks such as iron ore and taconite is under current investigation, but in the Lake Superior iron mining district, open pit blast-hole drilling in ore has been accomplished almost exclusively by standard churn drilling. The only recent advance has been the use of larger machines drilling 9-in. holes. This has increased drilling speed somewhat and allowed wider hole spacing, with consequent cost reduction.

Feb 1, 1956

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system.

Jan 1, 1941

By N. A. D. Parlee, I. D. Shah

ThIS reports on some work done on the solubility and diffusivity of oxygen in liquid silver. Solubility. Improvements in the measurement of the solubility of oxygen in silver and silver alloys were made because precise data were needed for calculating diffusion coefficients of oxygen in these alloys. The apparatus and the procedure used were similar to those of Parlee and Sacris.' The main improvement was in the temperature-measuring technique. A MV30 mullite protection tube containing a calibrated Pt-Pt, 10 pct Rh thermocouple was inserted in the reaction tube from the top through a vacuum-tight swage-lok fitting. The protection tube was well-immersed in the liquid silver, which was heated by induction. A Leeds and Northrup potentiometer was used in connection with the thermocouple. All runs reported were made at 1 atm. The temperature range investigated varied from 940" to 1200°C. The ternary point in Ag-0 phase diagram2 is at 939°C and 0.32 wt pct O. This point was reinvestigated using the above-described apparatus and was found to be at 939°C and 0.315 wt pct 0. It was determined by observing the sudden evolution of oxygen at this point while the solubility measurements were made. The point was easily reproducible if precautions were taken to keep the liquid silver essentially in equilibrium with oxygen and to lower the temperature very slowly. All of the results of this new solubility investigation are plotted in Fig. 1. They are represented by the "least-squares" line shown in the figure and the following equation for solubility at po2 = 1 atm: log% O =695.4/T - 1.086 This equation differs only slightly from that proposed by Parlee and sacrisl and that of Diaz, Masson, and Richardson.3 The points of Parlee and Sacris, using an optical pyrometer, are shown for comparison.

Jan 1, 1968

By E. G. Leonardon

THE first to appreciate and foresee the value of applying electrical measurements to structural studies was Prof. Conrad Schlumberger, Professor of Physics at the School of Mines in Paris. One of his earliest practical undertakings in this line was carried out, in the field, at Fierville-la-Campagne, Normandy, in 1912. His book, published in 1920,1 still stands as an authoritative, fundamental treatise on the use of the electric current in geological studies, in spite of the rapid evolution of geophysics during the last seven years. A remarkable feature of this book is that, even then, it stressed the role of electricity in structural investigations and made public the first successful results obtained therewith. Stratigraphic studies have been pursued continuously by Conrad Schlumberger and his associates since 1912, the only interruption being the World War. The results attained demonstrate the wide possibilities of electrical exploration in structural work. This field of activity is, at the least, as varied and valuable as the search for ore. It is curious that until very recently it has so slightly attracted the attention of geophysicists and geologists on this continent. The purpose of this paper is to present briefly some examples of the practical application of the potential methods to geological studies. These examples are chosen from a number of problems solved in the field by our firm, in the course of its consulting practice. Certain fundamental points are briefly stated before the field operations and interpretations are described.

Jan 1, 1928

By F. Lynwood Garrison

There is probably no subject for study in the metallurgy of iron and steel of greater interest than the effect of manganese upon the properties of iron. Some of the peculiarities of iron and steel containing appreciable quantities of manganese were observed many years ago by Heath, Robert Mushet, and others; but it was not until the introduction of the Bessemer process, when a demand was created for large quantities of iron-manganese alloys, that such compounds of iron and manganese became articles of commerce. Since that time the demand for these alloys has steadily increased, the use of ferro-manganese not only becoming an absolute necessity in the ordinary Bessemer practice, but also essential to the manufacture of open-hearth, crucible steel and steel castings; in fact it is the only source of supply for all the manganese used in metallurgical opera-

Jan 1, 1893

By H. E. Mussey

When the American Institute of Mining Engineers visited the Birmingham district in May, 1888, the four Ensley furnaces (Fig. 1) then completed were referred to as monumental.' Their dimensions are givcn in Table 1. Mr. Gordon stated, with considerable satisfaction, that on the preceding day one furnace had produced 165 tons. The blast was

Jan 1, 1925

By G. C. Stone

At the conclusion of my paper on the same subject read at the Boston meeting of the Institute, I offered to send some of sample No. 2 to any chemist who wished to analyze it. Eight chemists wrote to me for samples; so far I have received results from five. I give these results in a table (on the following page), together with the results previously obtained: As to the chemists and their methods : K is an iron-works chemist whom I only know by correspondence; lie writes: "No. 27(13.64) was obtained by the method I generally use, as follows : Dissolve 0.8 grams spiegel in hydrochloric acid and a little potassium chlorate, in a half-liter flask. Boil off most of the acid, add ammonia in slight excess, redissolve in acetic acid, using rather more than is really necessary, and then add 8 or 10 grams of sodium acetate and make up to the mark with warm water. Boil hard for fifteen minutes, then allow to settle (cool?), until the liquid reaches the mark, and withdraw 300 C.C. of the nearly clear liquid. Add to this an excess of hydrochloric acid, evaporate to dryness, take up with hydrochloric acid and water, and separate the iron by two precipitations with ammonia (I have often tested the ferric hydrate for manganese, but have never found any, if the separation by ammonia was properly made). Finally, precipitate the manganese as phosphate." Nos. 28, 29 (13.35, 13.07) were by Ford's method." No. 30 (13.50) was by Troilus's method He writes, " I may add the results are quite as good as I expected, although for any element except manganese, they are not close enough for anything like accurate work." L is a firm of commercial chemists of large experience who have made a specialty of iron work. Their method is as follows : Dissolve

Jan 1, 1884

By E. J. Dulis, V. K. Chandhok, J. P. Hirth

Cobalt clearly increased the activity of carbon in austenite and in ferrite. This effect of cobalt on carbon activity Plausibly accounted for the effect of cobalt on accelerating the austenite to pearlite transformation. Cobalt was found to have only a slight effect on carbon diffisivity in various Fe-Co and Fe-Co-W-Mo austenites, but was found to decrease carbon diffusivity in Fe-Co ferrite. THE effect of cobalt in steel is unique in that it is the only element that reduces hardenability by accelerating the austenite to pearlite reaction. The results of several excellent investigations aimed at explaining the role of cobalt have been published,1"7 but a complete understanding is still lacking. In addition, cobalt significantly enhances the resistance to softening or tempering of highly alloyed highspeed and hot-work tool steels. The resistance to tempering is related to the secondary hardening reactions associated with the fourth stage of tempering during which carbides of molybdenum, tungsten, and/or vanadium form in a martensite matrix. The effect of cobalt on secondary hardening reactions in high-alloy tool steel has received considerable attention, but a full explanation of the reactions involved has not been developed. Inasmuch as austenite to pearlite transformation and secondary hardening involve carbide formation, the present authors believed that the role of cobalt in effecting carbon activity and diffusivity in austenite and in ferrite was important to a fuller understanding of the phenomena involved. TO investigate the effect of cobalt on the activity coefficient of carbon in austenite, an approach was used similar to that used by Darken17 in his experiments on the effect of silicon, manganese, and molybdenum on carbon activity and diffusivity in austenite. TO

Jan 1, 1962

By Roy Thomas

SOON after the Waelz plant for the fire concentration of low-grade zinc ores was put into operation in the early part of 1929 at Katowice, it was found that the conveyor equipment for transporting the hot residue from the furnace dust chambers was inadequate. Hand tram-ming with water cooling was used for a time, but that method was injurious to the workmen as well as costly. The problem was to find some practical mechanical means of conveying flue dust at temperatures of from 450° to 600° C. as it was drawn from the dust chambers. After considerable preliminary investigation it was decided to install pneu-matic equipment for conveying the hot materials to a central mixing plant, where it would be mixed with slime and from which it would be returned to the furnace feed hoppers. The first pneumatic equipment was installed in 1930, and has been in successful operation since that time. The pneumatic method of transportation has shown a considerable saving in operating costs over the former methods of dust handling and a decided improvement in working and hygienic conditions at the plant, through the elimination of the dust hazard. Additional pneumatic equipment was installed in 1933 for conveying the furnace fume from the baghouses to the roaster plant. At the same time pick-up lines were provided for collecting the cleanings from the vertical and horizontal cooling pipes that are between the furnace dust chambers and the baghouses. The latter installation has practically eliminated a dusty and costly hand-tramming operation.

Jan 1, 1939

By C. S. Trewin

Zinc, in its wrought form, is produced commercially in rolled strip, sheet, wire, rod and tubing. Wire has been made periodically, but due to the fact that slight drafts are necessary, the cost of production is greater than for the more common non-ferrous metals which are made into wire. Notwithstanding the cost, zinc wire has certain special uses for which it is particularly adaptable. Rod has been made both by rolling and extrusion; the product, however, has not indicated great commercial value. Tubing has been made from strip from time to time by forming a strip around a mandrel and either electrically or gas-welding a longitudinal joint. Recently a tube manufacturer has succeeded in making a fair quantity of this material. Its commercial adaptability is still to be dctcrmined but anyone who desires it can obtain quantities of the smaller sizes. Inasmuch as strip and sheet are commercially the most important, this paper will be devoted to these products. In the broader sense, zinc is not alloyed. That is, there are no combinations comparable to the various copper, aluminum and nickel alloys. It has been recognized for some time that the lead and cadmium occurring with commercial zinc have some effect on its properties and such alloys as may be said to exist are those made from zincs containing varying amounts of lead and cadmium with a relatively low iron content. The foreign rolled zinc will analyze higher in lead than the domestic grades. A representative foreign analysis will run 1.1 per cent. lead, 0.07 per cent. cadmium and 0.02 per cent. iron. The American grades vary from zinc approximating high grade and analyzing 0.08 per cent, lead, 0.002 per cent. cadmium and 0.015 per cent. iron, to the lower grades in which the lead will vary from 0.3 to 1.0 per cent., cadmium from 0.10 to 0.5 per cent. and the iron in the neighborhood of 0.02 percent. Rolled Zinc Rolled zinc is produced in both the strip (or ribbon) form in which the product is rolled from a single bar in one continuous direction, or sheet in

By J. R. Thoenen

THE preper classification of mining methods has received the earnest study of many mining engineers and has resulted in much technical controversy, depending no doubt upon the point from which classification is viewed or the use to which it is put. So far as the writer is aware, the discussion has invariably centered around the classification of underground mining methods, and only superficial attention has been directed to surface methods. Volume 72, page 10, of the Institute Transactions, presents such a classification, sponsored by the Mining Methods Committee of the Institute. A similar classification by Prof. Hugh P. Nicholson appeared in Mining and Metallurgy in October, 1934. The two classifications are quite different in their treatment of underground methods but are identical in classifying surface methods, although Professor Nicholson does suggest possible further divisions for surface mining and admits that such subdivision is more difficult than appears at first. Surface subdivisions as given by these two authorities are as follows, showing that in spite of rearrangement the two classifications are identical: From his experience of many years in the study and operation of both underground and surface metal and nonmetallic mines, the writer does

Jan 1, 1942

By Robert Glass Cleland

WITH the acquisition of the Nichols Copper Company ' and the development of the large Copper Products manufacturing and selling organization, the Phelps Dodge Corporation had attained two of its important goals. But at that particular time both its immediate and long-range prospects were giving the company serious concern. The financial panic that began late in 1929 was growing worse instead of better. Neither raw materials nor finished products could find a market. In 1932 the price of copper fell to the almost unprecedented figure of four and eight tenths cents a pound. Domestic production of copper in the United States was further threatened by a large low-cost output from the mines of Africa and the Andes. Canadian copper mines, with their large yield of other valuable metals from the same ores, added to the difficulties of the American companies. After a hard-fought campaign, however, the producers of domestic copper finally induced Congress to levy a duty of four cents a pound on copper imported into the

Jan 1, 1952

By Immo H. Redeker

Through close cooperation with geophysical and geological test work by Texas Gulf Sulphur Co. in Beaufort County, the Asheville Minerals Research Laboratory assisted in the evaluation of North Carolina's most valuable mineral resource, the Pungo River phosphate deposit. After a core evaluation study, the flotation process for the concentration of North Carolina phosphate was demonstrated in a 500-lb per hr pilot plant in Asheville. Tonnage samples of phosphate concentrate were produced for customer evaluation in the United States, Europe, and the Far East. Plans for a larger pilot plant to be erected at the plant site at Lee Creek were prepared for TGS. The larger pilot plant was operated by TGS in conjunction with a test dredging operation which led to the adoption of a dragline dry mining method to move 90,000 tpd of material for the production of 10,000 tpd of phosphate concentrate in the all-flotation phosphate concentrator. Calcining, dry grinding, and byproduct studies complimented the construction of one of the world's largest and most modern fertilizer raw-feed complexes on the eastern North Carolina seaboard.

Jan 1, 1972

By R. L. Wiegel

The National Science Foundation, Erie Mining Co., and University of Minnesota Mineral Resources Research Center jointly sponsored a project to demonstrate the use of a small computer in the control of cyclone overflow size on one line in the Erie Mining Co. concentrator. The Erie circuit, similar to most taconite circuits, uses magnetic separators to reject tailings following each stage of grinding, resulting in additional variations in the demands made on the grinding circuit because of weight rejection fluctuation. Mathematical models were developed for rod milling, ball milling, hydrocycloning, fine screening, and five stages of magnetic separation. These models were used in concert to simulate the operation of Erie's circuit from rod milling through finisher magnetic separation.

Jan 1, 1980