Search Documents

By P. Niessen, W. C. Winegard, C. J. Beingessner

DURING the last 10 years, several grain-growth studies have been made using zone-refined metals with controlled amounts of solute to elucidate the interaction of solute with moving boundaries. In all these studies, it was more or less implicitly assumed that the alloys used were, after recrystallization and grain growth, homogeneous within the grains with respect to solute and lattice defects. This note deals with observations made on microstructures originating from solidification of dilute alloys and from grain growth. Briefly, the experimental procedure used in these studies was the following: zone-refined cadmium and master alloys were melted and cast in Pyrex under vacuum to produce bars 14 mm in diam and about 150 mm long. These bars were cut into 8-mm-thick slices which were mechanically and chemically polished. The specimens were then deformed 30 pct in compression and given a 1-week anneal at 260°C in argon. After this anneal, a second deformation produced completely recrystallized samples 4 mm thick. The time-temperature controlled anneals were carried out in a bath of silicone oil. After the grain-growth anneal, the specimens were polished in Gil-man's' solution (33 g CrOs, 6 g NazSO, in 100 ml of water). Several etches were used depending on the alloy investigated, but mostly a mixture of concentrated HC1 and HNOj (98:2 vol) was employed. In all the alloys examined, the ease with which substructures could be revealed depended strongly on the crystallographic orientation of the surfaces of the grains. However, very frequently the microstructures to be discussed here etched up over broad areas comprising several grains. Fig. 1 is a micrograph of a Cd-0.05 at. pct Mg alloy annealed for 100 sec at 270°C. Different substructures are seen in this photograph. A denotes the now existing grain boundaries. The well-defined lines and points marked B are the remains of a solidification substructure. The lines are boundaries between cell colonies, and the points are nodes located on regular two-dimensional cells. This cellular structure has the same appearance as that found by weinberg2 for rapidly quenched Zn-Au alloys. The "ghost boundaries", marked C, are very similar in appearance to a grain boundary array in a polycrystalline sample. Repeated polishing and etching showed that all the substructures observed were three-dimensional. To date, the ghost boundaries have been clearly observed in all samples containing 0.005, 0.01, 0.05, and 1 at. pct Mg, and in samples containing 0.01 at. pct Zn. Attempts to outline these ghost boundaries in cadmium alloys containing 0.01 at. pct Ag and Au were only partially successful. In these alloys, parallel lines, having a resemblance to the ghost boundaries in the Cd-Mg and Cd-Zn alloys, were observed, but it was not possible to obtain complete arrays of ghost boundaries which extended over several grains. It is possible that a different etch than that presently employed would reveal the ghost boundaries in the Cd-Au and Cd-Ag alloys as clearly as in the Cd-Zn and Cd-Mg alloys. A close examination of the ghost structure showed that it consisted of linear etch-pit arrays, Fig. 2. The ghost boundaries were resolvable even in grains which showed over-all faceting due to the etching, as seen in the corner of Fig. 2. The general appearance of the ghost structure suggests that it originated during grain growth. This is supported by the observation that the mesh width in the ghost-boundary array generally increased with increasing final grain size. To test whether the ghost structure was formed during the long homogenizing anneal or during the grain-growth anneal, some as-cast samples were deformed and given a grain-growth anneal. This anneal was terminated by air cooling or

Jan 1, 1967

By Thomas Read

IN speaking of immaterial problems of industry I am using the word immaterial in its original sense, not consisting of matter; not in its derived sense, unimportant. There is nothing of a paradox in saying that immaterial problems are the most important in human life, for His a matter of everyday observation that much of the news in the daily papers, and most of the world's best literature and drama, deal with human conduct that has for its motive forces that are but little concerned with material things. The engineer's preoccupation with physical forces, in extending his control over them, has not blinded him to the impor-tance of forces that, for want of a better word, I call immaterial; but he has considered that dealing with the one is his job and the other is not. All the evidence of the past decade indicates that the latter are so in-extricably interwoven with the former in modern in-dustrial life that the engineer will have to concern himself with them whether he wants to or not. Some of the most important of the problems arising from the action of these forces relate to the mental hygiene of the workers in industry. Mental hygiene in industry was concisely defined, in terms of the best present knowledge, by Dr. C. Macfie Campbell, speaking last April before the executive com-mittee of the Associated Industries of Massachusetts, and as his statement can scarcely be bettered, I quote it below: "The term mental hygiene is apt to appear vague. The actual stuff with which mental hygiene deals may be briefly reviewed.

Jan 9, 1927

By AIME AIME

THE 122d meeting of the Institute was held in the Lake. Superior Copper and Iron Country Aug. 20 to Sept. 3, 1920 with an approximate registration of 1100 members and guests. This is the 'first visit of, the Institute to this vicinity since 1904 although previously it held meetings there every six or, seven years. 'The eastern party assembled at Buffalo and sailed on the S. S. "Tionesta ". on Friday morning, Aug. 20, arriving at Houghton, Mich., Monday, Aug. 23. En route stops were made at Detroit, where sightseeing auto trips were taken, and at Mackinac Island, where a short stop permitted a visit to the picturesque and historic Fort Mackinac.

Jan 1, 1920

By G. Sandoz, D. A. Meyn

The fracture surfaces of specimens of titanium a1loys which exhibited susceptibility to subcritical crack growth in a wide variety of environments, including aqueous solutions, alcohols, hydrocarbon gases, carbm tetrachloride, and dry air, were examined. The dominant and characteristic fracture mode was cleavage. which became mixed with an increasing porportion of ductile fracture modes (dimples. and so forth) as the applied KI was increased. The cleavage plane in all the alloys was oriented at 15 deg from (0001) of the a phase. No indices could be assigned to the 15 deg cleavage Plane because of uncertainty as to which zone it belonged to. SLOW crack growth and delayed fracture take place in certain titanium alloys at stress intensity (KI) lower than the critical values for complete fracture (KIc) found in short-time tests for plane strain fracture toughness.' Such crack growth may take place in very dry air on sustained loading if the alloy contains a sufficient amount of hydrogen and if the stress intensity factor is higher than a threshold value designated KIH.2 Similarly, a number of environments such as water, alcohols, and hydrocarbons may cause slow crack growth provided the stress intensity factor exceeds the threshold value KISCC. In this paper it is intended to examine some fracto-graphic and crystallographic details of this subcritical crack propagation process as related to alloy composition, environment, and stress intensity. It has been previously reported that subcritical crack growth takes place in titanium alloys in aqueous environments by cleavage.2"6 The observations to be described here indicate that in the alloys investigated the mode of subcritical crack propagation is more dependent on the stress intensity during cracking than on the environment. The fracture mode is illustrated with photographs of the fracture surfaces at a wide range of magnifications. The crystallographic character of the cleavage mode is also presented and the results discussed. EXPERIMENTAL APPROACH The studies were made on four titanium alloys— Ti-8A1-1Mo-lV, Ti-5A1-2.5Sn, Ti-7Al-1Mo-lV, and Ti-0.350. Of these four alloys the first two were mill annealed and fine grained. The latter two were noncommercial and coarse grained, having been prepared for other experimental purposes. The crystallographic studies required a large-grain size. Consequently the fine-grained alloys were an- nealed in a vacuum at 1950°F and furnace cooled to produce samples for these studies. This treatment did not alter the microstructure significantly except for grain size. All the aluminum-containing alloys showed primary a with a network of ß-phase particles within the a grains; Figs. 1 and 2 show this microstructure for the specific case of fine-grained Ti-8A1-1Mo-1V. The cracks in the figures will be discussed later. Fractographic studies were made on all the alloys, but the electron fractographs displayed herein are from the Ti-8A1-1Mo-1V alloy in the fine-grained condition. Emphasis was placed on this commercial alloy because considerable information was available on the stress-corrosion cracking characteristics in a variety of environments. Sufficient supplementary studies of the alloy after the anneal to produce large grains were conducted to establish that the stress-corrosion cracking susceptibility and fractographic characteristics were not changed significantly. Thus it could be inferred that the crystallographic data obtained exclusively on large-grained specimens would apply also to fine-grained specimens. Fracture surfaces for study were obtained using precracked cantilever beam specimens loaded as described by Brown. The precracked section of a specimen was immersed in the environment of interest. Values of initial stress intensity factor Kli were chosen slightly higher than KISCC in order to obtain a fairly extensive region of slow crack growth. Fracture surfaces representative of a variety of stress intensity levels could then be examined because in the cantilever beam test KI increases as the crack propagates.

Jan 1, 1970

By Georgc E. Collins

SEVERAL years ago, I estimated the total stock of gold in the world to be about a thousand million ounces, of which rather over one-third was available for monetary uses. Robert H. Ridgway has estimated the world's production from 1493 to 1927 as slightly over this amount. Of this total, 1.5 per cent was produced between 1493 and 1850 (before the Californian and Australian goldfields began to flood the world with gold), 331/2 per cent from 1851 to 1900, and 511/2 per cent from 1900 to 1927. Allowing for loss by attrition and permanent consumption in the arts, and for loss of buried treas¬ure, my first-mentioned estimate is perhaps not far from the truth; but my estimate of the monetary stock was certainly too low. Of the total production stated by Rid-way. 28 per cent came from North America. 26.9 per cent from Africa, 1.6.8 per cent from Australasia, 12.4 per cent from South America, and 11.2 per cent from Asia. Excepting that from the African conglomerate beds, the ultimate origin of which is still the subject of controversy, by far the greater part of the total production was derived from alluvials. Weighing all contingencies, it is improbable that any such production as has been made during the last forty years will be repeated in any similar period, if the present price level is maintained. The gold standard today seems firmly established except for temporary digressions. Nevertheless, no well-informed mining engineer will venture to assert the probability that the material for its maintenance throughout future generations can be furnished.

Jan 1, 1932

By James P. Sloss

MOST students that plan to enter the mining profession attempt to obtain some kind of practical experience before graduation. Six or seven years ago it was an easy matter for undergraduates to find employment during the summer vacation and return to school in the fall filled with enthusiasm to dig deeper into the theoretical field. However, during the past few years it has become extremely difficult for an inexperienced undergraduate to obtain even a menial job in mining. This was the situation which presented itself to the author and his partner, T. M. Patten several months before school closed in May, 1934. At that time, Mr. Patten's training consisted of two years study in Mining, and mine included three years' study in Mining Geology at the Missouri School of Mines and Metallurgy. With this technical training and no practical experience, we conceived the idea that custom assaying in some of the western mining districts should be a lucrative business. We thought that the renewed interest in prospecting for gold and the opening of new mines should provide more assay work, and believed that we might secure it if we were on the spot where the assaying was needed. We realized that it would be out of the question for us to obtain the necessary equipment with which to establish an assay office. Even if such an office were established we had a maximum of but three months during which to operate. So we determined to build some kind of inexpensive equipment that could be placed in an automobile, or trailer, and be moved from one camp to another. We then began to study the theoretical aspects of assaying and started experimental work with the equipment that we proposed to build.

Jan 1, 1935

By G. W. Tower

THE YEAR 1931 was for most American copper producers one of restricted output but extremely low production cost.. When compared with 1929, the marked reductions in costs achieved in 1931, operating at rates in many instances a third to a half of capacity, can only be regarded as remarkable. In fact, the recent shut-down of several large operations suggests the probability that 1931 costs represent a bare minimum for many properties. Before discussing the 1931 results a few remarks on cost data are appropriate. The type of cost tabulation here presented was first published in 1929, (A. B. Parsons. E. & M. I. June 8, 1929), and has appeared each, succeeding year following in general the calculation method and company set-up of the original article. (. G. W. Tower, E. & III. L, July 8. 1930; S. D. Strauss, E. & M. J.; July 27, 1931). As far as possible the leading American copper companies are included. In considering these cost tabulations it must be borne in mind that the information from which they have been prepared is entirely contained in the annual report of each company; and that a multiplicity of interests and a condensed income statement for some of the larger companies, such as Cerro de Pasco and Kennecott, make the cost figure an arbitrary one depending upon sundry metal credits, metal products, miscellaneous income, etc. For Granby, Howe Sound. Magma, and Noranda, sundry metal credits are important. Furthermore Andes, Chile and Greene Cananea give costs only against copper sold. Although the individual costs here figured are by no means absolute they are computed by the same method each year and offer a basis of annual comparison; and with attention to footnotes the premises on which the costs are based may be easily followed.

Jan 1, 1932

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930

By M. C. LAKE

THE industrial development of the United States has been stimulated by the presence of high-grade iron ore in the Lake Superior district. These great deposits have been susceptible to economical extraction and are conveniently located for cheap lake vessel transportation to the great consuming centers. The district furnishes from 80 to 85 per cent of the iron ore annually consumed in the United States, and a full understanding of the available supply of this great commodity is so important that it is well to consider whether or not the industrial supremacy and national independence attained as a result of the abundance of cheap ore are permanent. The enormous deposits of high-grade ore available in the Lake Superior district have been the foundation upon which the vast industrial structure of the steel and allied industries has been built. It is extremely important to the country as a whole, and especially to those States and communities now dependent on Lake Superior ore for their prosperity, that their industries shall retain the particular advantages with which they are now endowed, and that a generous supply of high-grade raw material be available for their consumption at a satisfactory cost. The steel industry is so basic and fundamental that any fluctuation in the cost of its finished products as determined by the supply and cost of the raw materials involved in its manufacture will necessarily affect the business of a wide variety of industries which are dependent on it.

Jan 1, 1926

By D. M. Hausen

This study identifies and describes various crystalline phases of the V205-Na20 system, and relates their properties to metallurgical aspects of vanadium production. Phase equilibria and stability ranges of sodium vanadate phases of varying molar ratios of Na20/V205 were investigated in a variety of plant products, ranging from fused "black cakes" (V20 melts) to "salt roast" calcines. Crystalline compounds, Including vanadium pentoxide, V205; sodium vanadyl vanadate, 6 phase, Na2O.V2O5.5V2O5; sodium vanadyl vanadate, y phase, 5Na20.V204.12V205; sodium metavanadate, Na20 .V 05; sodium pyrovanadate , 2Na20 .V205; and sodium orthovanadate, 4Na20.~2~5, have been characterized with the aid of X-ray diffraction patterns, infrared spectra, and optical properties in addition to chemical analyses, as a guide to mineralogical "troubleshooting" of plant problems and processes in vanadium pyro- and hydrometallurgy.

Jan 1, 1984

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

Jan 1, 1967

Jan 1, 1967

By William F. Boericke

KIRKLAND LAKE and Porcupine in 1931 accounted for more than $41,625,000 of Ontario's total gold production of $43,117,688. For the first time, the younger camp surpassed the older in gold output, producing $21,734,000 against $19,891,000 for Porcupine. Present output of both camps is increasing, and should pass the record figures of 1931 before the year is out. In May of this year, Porcupine mines milled 285,759 tons, with a bullion value of $1,810,009; the corresponding figures for Kirkland mines are 149,188 tons and $2,104,757. A much higher average value per ton for Kirkland ore, $14.10 against $6.33 average for Porcupine accounts for the difference. The two fields are about 100 miles apart by rail, and there are important differences in the character of the ores, which accounts largely for the difference in milling costs and in final tailing values, despite excellent metallurgical work in both the fields.

Jan 1, 1932

By R. N. Zitter

PRESENT work was done in connection with a program for obtaining a low energy gap semiconductor suitable for photodetection. The inter-metallic compound InSb, which is now being in-

Jan 1, 1959

By Rclssell Gibson, F. S. Turneaure

The tin deposit of Monserrat; Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 1, 1950

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By R. W. Smith

It is well known that certain silicates such as the feldspars and beryl can be readily floated from quartz at a low pH value using a long chain cationic collector in the presence of a fluoride.1-3 However, the mechanism whereby the fluoride activates feldspars and beryl is not known. Indeed, only a few authors have even speculated about possible mechanisms.1,3,4 As a first approach to the problem, it is perhaps best to look closely at the interesting character of hydrofluoric acid and how it dissolves silica and silicic acid. Hydrofluoric acid, unlike hydrochloric acid, is a weak acid with a dissociation constant of about 3.53 x 10-4 at 25°C.5 The reason for the weak acidic character of HF lies in the very small size of the fluoride ion.6 The pKa value is 3.45 which means that at pH 3.45 half the HF is present in molecular form and half in ionic form. The anion present is probably HF2.-6 At pH values below the pKa value, molecular concentration increases rapidly at the expense of the HF2- anion. It is known that HF readily attacks glass, silicates, quartz and silicic acid. The equation usually cited pertaining to the first step in HF attack of silica is6-'

Jan 1, 1965

By J. W. Buch

IN THE FIELD of track haulage, interest has seemed to center on the question of larger mine cars both for handling material from loading point to shaft bottom or surface, and for shuttle service. Saving of time in car changing is obvious if larger cars are used. In addition, shorter trips result where car transportation is from face to opening without transfer. This also brings about side-track and equipment savings. Track shuttle service, using large automatic-dump cars (10 tons) between loading machines and trip loading point, has been a satisfactory solution for the operator who mechanizes a working mine regularly equipped with a large number of small mine cars. This development in track shuttle haulage, has made track installation and maintenance increasingly important, requiring closer supervision.

Jan 1, 1942

ALEXANDER BRYDEN Alexander Bryden, clean of engineers in the anthracite mining field, and a member of the pioneer Pittston family, was claimed by death Wednesday, September 26, 1917. The announcement was not a surprise, as he had been in a critical condition for several days. Mr. Bryden had been in failing health for a year past, but his indomitable will kept him at his accustomed duties until quite recently. Two weeks before his death he attended the regular weekly meeting of the Board of Directors of the Miners' Savings Bank in Pittston, Pa. At that time he apparently felt that his end was fast approaching, as he bade farewell to his associates on the bank board. Until a few days before the end, he continued to give attention to business matters at his home, in preparation for the end, which he met unflinchingly. In the passing of Mr. Bryden, northeastern Pennsylvania loses one of the best-known mining engineers, and the community, a man who, throughout his long life, was actively interested in its social welfare and business prosperity. He was for many years prominent in the management of the mining operations of the Pennsylvania Coal Co., and at the time of his death held the position of consulting engineer of the Pennsylvania and Hillside Coal. Companies.

Jan 12, 1917