Search Documents

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By L. Segle, R. Resnick

NUMEROUS experiments in the past few years have proven that void formation occurs quite generally in the diffusion zone of bimetal specimens1-4 The phenomenon has been explained in terms of the accumulation of lattice vacancies resulting from unequal diffusion of the constituents and their eventual precipitation as holes.= Attention has recently been directed to the fact that voids also form within homogeneous metals during high-temperature creep.' The idea has been put forward that these voids form by the condensation of excess lattice vacancies generated by intersecting dislocations.".' If the precipitation of lattice vacancies from solution is treated as a nucleation and growth process, the predicted vacancy concentration for homogeneous nucleation of voids at an observable rate is 100 to 1000 times the normal thermal equilibrium concentration. It appears that voids actually form during diffusion at vacancy supersaturations which are much lower than this8 According to the calculations of Machlin,' the same must be true for voids formed in homogeneous metals during creep, if these are considered to arise from the precipitation of lattice vacancies. Therefore, if the vacancy mechanism is valid, it seems that the holes which form in diffusion and creep specimens are heterogeneously nucleated by imperfections or impurities in the metal. Irregularities in the frequency and distribution of voids in diffusion couples bear out this explanation.' , It is not known at the present time what the nuclei are on which vacancies condense. Various investigators have speculated that they could be certain dislocation configurations, already existing voids produced during solidification or working, gas pockets, or inclusions in the metal. Relatedly, the precise value of the degree of vacancy supersatura-tion for void nucleation is still uncertain. An initial attempt to estimate this value from diffusion data, made by Balluffi, indicated that voids form in diffusion couples at vacancy concentrations which may

Jan 1, 1958

By T. A. Wright

THE SAMPLING of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or "metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also.

Jan 1, 1928

By W. O. Philbrook, K. M. Goldman, G. Derge

EQUILIBRIUM conditions for steelmaking reactions have been studied extensively over the past two decades by a .number of investigators, with gratifying results. Equilibrium data are essential to the understanding of any process, and such knowledge has the practical utility of placing a limit beyond which control measures cannot succeed. When, however, the driving rate of an industrial process is so fast that there is not time for reactions to reach equilibrium, it then becomes necessary that the factors which control the rates of reaction be known in order to establish full control of the process. The desulphurization of molten pig iron by slags within the iron blast furnace is one such process in which the actual degree of sulphur absorption by the slag does not approach the equilibrium distribution obtained for similar slag-metal systems in the laboratory.' A study of the rate-controlling factors governing the desulphurization of iron by slags is becoming increasingly important as the sulphur content of raw materials increases with depletion of higher grade ores and coal. Following up an initial study on kinetics,' this paper reports some results of a continuing laboratory investigation on the mechanism of sulphur transfer between molten iron saturated with carbon and slags of the CaO-SiO,-A12O3 system. Laboratory experiments cannot reproduce in detail the conditions which prevail in the hearth of a blast furnace, but they will contribute to an understanding of the smelting reactions and perhaps will explain some apparent inconsistencies in the factors controlling the equilibrium distribution of sulphur between iron and slags under reducing compared with oxidizing conditions. The mechanism of a reaction—that is, the individual steps and the sequence in which they occur to produce the overall reaction which is ordinarily observed—must be elucidated to learn which steps are the slow ones, or "bottlenecks," that fix the pace of the process as a whole. In the desulphurization reaction, for example, the overall rate might, in principle, depend upon the rate of diffusion of sulphur in the metal or in the slag, upon the speed of some homogeneous reaction taking place entirely within one of the phases, or upon some heterogeneous reaction taking place across the slag-metal interface. Even some side reaction or the back reaction might have some influence. Evidence on all of these points will be presented in this paper. The rate of diffusion of sulphur in both iron and slag is so slow that it seems necessary to assume that convection provides the mechanism of carrying

Jan 1, 1951

By T. W. Harris

This paper was written in conjunction with the work being undertaken by the Technical Committees on Classification of Coal, and an effort has been made to compile information relative to the use of coal for stationary steam generation in order to use this information to assist the Committee on Classification of Coal for the ultimate purpose of elimination of losses both by the reduction of individual effort and waste in the consumption of material. Under the auspices of the National Association of Purchasing Agents, a questionnaire was drawn up to develop this information from stationary steam plants throughout the United States in order to consolidate the information developed from the many hundreds of boiler tests on coals consumed by various coal-burning equipment. These questionnaires covered: 1. The company reporting, location and method of delivery to the plant. 2. Complete coal data, including description of coals used (with sufficient space to include first, second and third preference) on source of coal used, complete analysis and factors affecting choice of coal used. 3. Plant data, divided into: (a,) hand-fired, (b) overfeed stokers, (c) underfeed stokers, (d) traveling grate stokers, (e) pulverized coal; and included complete description of furnace data, draft data, coal-burning rate, type of stoker, type of pulverizer, efficiency data and remarks. The questionnaire was drawn up by consultation with various combllstion engineers, including B. J. Cross, Test Engineer of the Combustion Engineering Co., W. H. Fulweiler, of the United Gas Improvement Co. and the U. S. Bureau of Mines. In all, 11,538 copies of the questionnaire have been distributed, of which 4369 were sent in duplicate. Our estimate of the total volume of bituminous coal consumed in stationary steam boilers over the 12 months of 1930 is approximately

Jan 1, 1934

By H. G. Doll, H. P. Schwede

This paper describes a method to provide identification of particular depths in a borehole through the use of radioactive markers. The correlation of a marker, placed in the wall of a borehole, with known points of the electrical log and with the casing collars in the cased hole permits accurate positioning of tools with respect to a formation, regardless of absolute depth. Such a process is particularly useful in gun perforation of a casing in a well. Technique and equipment are discussed and illustrated. Examples are given of practical application in the field. Introduction During the past decade the search for petroleum has increased the importance of testing zones at depths in wells which have become progressively deeper. The development of new techniques, such as electrical logging, has permitted the identification of producing formations which consist of comparatively thin strata. When thin beds are to be produced at great depths, the problem of positioning tools accurately to place the well in production becomes acute.l Continuous consideration is being given in the petroleum industry towards the improvement of depth measurements in a borehole. The accuracy in absolute depth measurements, whether made in an open or cased hole, whether determined by a cable or a drill pipe, depends upon a number of factors, such as tension, temperature, and calibration. For example, the effects of tension from the weight of 10,000 ft of drill pipe and the thermal expansion of this length . of pipe, where its average temperature has increased SO"', will Produce an elongation as much as 8 ft.2 The effects Of such factors can be minimized through the use of care in depth measurements, the application of corrections based on experience, and continuous calibration or checking. The fact that different methods and different tools are used to determine the depths of formations in wells will sometimes give rise to a difference between measurements. It is evident that an important requirement in a well is the ability to locate at will any subsurface point. While absolute depth measurements have ion in recent years, it is reassuring to have other means to verify, for example, that a casing is perforated at a particular place with reference to a zone within a formation. Such a check on measurements may be had by placing a reference marker at a point known with respect to the electrical log of the borehole. That point is usually chosen to be in proximity to the 'One to be perforated. Thus, only short in depth measurements are made and any inaccuracy becomes very small and of minor importance' The use of reference markers located at fixed points predetermined in each zone where future operations are contemplated enables the operator to position any tool

Jan 1, 1948

By Chas. A. Dobbel

The Chief Consolidated properties are situated in the Tintic mining district of Utah, being included in Juab and Utah Counties, about 70 miles south of Salt Lake City. The drilling referred to in this paper has been carried on in the Chief Consolidated No. Pmine, the Gemini mine, and the Eureka Hill mine at Eureka, the Grand Central mine, above Mammoth, and the Apex Standard mine just south of Dividend. The occurrence of ore through the district is typically in lenses on bedding or breaks, and in connecting pipes, without accurate geometrical trend so that the ratio between the total length of development in drifts and crosscuts to the square feet of ore exposed is very high. A section of one of the western channels (Fig. 1) through the Tintic district, shows, roughly, the irregularities calling for excessive development work, so typical of the Tintic mines. This irregular trend of the ore constantly calls for excessive cutting up of the whole area for offshoots and the connecting links always present. In the planning of prospecting and development, no regular system may be laid out without overlooking some orebodies or segments of orebodies. It was with these facts in mind that Cecil Fitch, the general manager of the Chief Consolidated Mining Co., decided that some method of drilling was the more feasible way of successfully cutting up and bringing about the discovery of ore believed to exist; yet this drilling had to compete with a great margin of cost over crosscutting, as a crosscut in the Tintic district, even though barren, brings out geologic facts that, in many cases, are worth the price of the working itself. Diamond drills met with the success that might be expected in a district that has a reputation for the Gear and loss of diamonds; after 6 or 8 months, this method was discarded on account of the high costs. Simultaneously, a small churn drill outfit was set up underground but a few shifts proved its inapplicability. At the same time, the ordinary hammer drill was used to drive prospect holes with jointed steel. Just what equipment to develop for this work with the hammer drill involved much experimenting, as nothing was found in the literature

Jan 1, 1925

By R. P. Corbett

Since the beginning of operations at the Kelley mine in 1952, Anaconda has emplaced more than 150,000 cu yd of concrete underground. Concreting practices have changed over the years but the net result is still the same- lower costs along the line and more versatility.

Jan 7, 1961

By E. S. Wheeler

THE rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the latter weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. FIG. 1.-A GROUP OF MONEL METAL AND NICKEL CASTINGS. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant. equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success.

Jan 1, 1930

By Z. E. Arlin, R. D. Lynn

A deep well injection system is used by The Anaconda Co. for the disposal of uranium mill tailing water near Grants, N. M. A 2511-ft hole was cored and tested through Triassic, Permian, and Pennsylvanian (?) sediments and bottomed in Precambrian granite gneiss. The disposal well was plugged back to 1830 ft and completed in 563 ft of sandstones in the Yeso formation. The reservoir sandstones contain water similar to the injected waste water, and are isolated from overlying fresh-water aquifers by an evaporite barrier zone. Mill tailing water is decanted, filtered, and introduced into the well by gravity at an average rate of 400 gpm. The reservoir has a life expectancy of 10 years. The Anaconda Co. began uranium milling operations near Grants, N. M. in 1953 with a small mill that processed limestone ores. A larger second mill was built in 1955 to treat sandstone ores. In 1956 it became apparent that a large tailing pond would be required to contain the increased discharge of mill waste water. Research was begun on supplementary methods of disposal by which a minimal pond size could be maintained to avert excessive seepage losses. An intensive sampling program was begun to monitor the fresh-water wells in the area. The original limestone mill ceased operation in 1959. The present mill treats sandstone ores by sulfuric acid leach and a resin-in-pulp ion exchange recovery circuit that uses chloride elution. Process waste water is discharged to a tailing pond where, after evaporation losses, an annual average of about 400 gpm are available for injection into the disposal well. The waste water is a mildly acid solution that contains large amounts of manganese, iron, and the sulfate and chloride salts of sodium, calcium, and magnesium. It is a low-level radioactive fluid that contains small amounts of Uranium-natural, Thorium-230, and Radium-226. The average chemical and radioactive analyses of the waste water injected into the disposal well are shown in Column B of Table I. Disposal of the excess mill waste water by deep well injection was investigated after extensive research had proved that alternate methods were not satisfactory. A study of the regional geology and hydrology indicated that a disposal well was feasible, and a test well to basement rock was planned. Tentative plans for the test well and the results of the geologic and hydrologic studies were submitted to the New Mexico Dept. of Public Health, the New Mexico State Engineer's Office, the U.S. Atomic

Jan 1, 1962

By H. D. Kessler, Joseph B. McAndrew

WHEN there is occasion to make structural use of metals at temperatures above 900°C (1652°F), the choice of alloys is severely limited, and those materials which meet special requirements as to density, strength, toughness, and resistance to creep, oxidation, or fatigue at such temperatures are at a premium. Any new type of high temperature alloy which is found to be outstanding with respect to several of these properties is therefore likely to find special applications for which it is uniquely advantageous as compared to other alloys. Such is the case with the 7 titanium-aluminum alloys. This y phase is an intermediate phase based on the composition TiAl, and extends from about 35.5 to 44.5 wt pct Al at temperatures up to 1000°C, above which the field broadens to include 60 pct A1 at 1340°C.' The alloys of principal interest have a narrow melting range, with 7 forming by the peri-tectic reaction, melt + ß=y at about 1460°C. Unlike most intermediate phases, the binary alloys containing titanium and aluminum in approximately equiatomic proportion possess low room temperature hardness,' in addition to which they have low density, good resistance to oxidation, and relatively high modulus of elasticity.' Unpublished work done at Armour Research Foundation showed

Jan 1, 1957

By W. H. Emmons

IN 1922 Morey made a series of experiments in which he observed the cooling of a molten system containing H20, 9.1 per cent; K20, 17.3 per cent and Si02, 73.6 per cent. This system was confined in a bomb; it was fluid at 500° C. and exerted no vapor pressure. In cooling to 420° C. a large part of it crystallized and at that temperature much of the water had separated from the crystals and remained as steam, which built up a pressure of 4998 lb. per sq. in., a force sufficient to lift nearly one mile of granite.1 If granite, cooling at 600°, expels vapor in the process of crystalliza-tion it is reasonable to suppose that a considerably greater vapor pressure would result, and it is thought that the vapor expelled from crystallizing granitic batholiths probably has a pressure sufficient to lift two or three miles of granite. This vapor, collecting near the tops of cupolas of batholiths, is believed to exert sufficient pressure to fracture the hoods and roofs of batholiths above the cupolas. If that is true, one would expect to find that the fracture systems above cupolas are arranged in patterns that depend in part on the shapes of the cupolas. The mechanics of the situation seem to require that conical cupolas should have radial fracture patterns, that bluntly rounded cupolas should have fracture systems that are either irregular or rudely conjugated in plan, and that elongated stocks or cupolas should have fracture systems in which the fractures lie nearly parallel to the direction of the elongation of the cupolas.

Jan 1, 1934

By F. M. Perkins, R. H. Jamison

Publications concerning scaling laws for laboratory flow models of oil reservoirs indicate that the relative permeability and capillary pressure relations must be the same functions of saturation in the model and its prototype. In this paper, the relative permeabilities and saturations are redefined in a way which permits one to have diflerent relative permeability and capillary pressure relations in the model and prototype. The development of the new scaling criteria is demonstrated by deriving scaling laws for one simple flow problem. INTRODUCTION The successful application of information gathered through bench-scale model studies to the prediction of multi-phase fluid flow behavior in petroleum reservoirs requires careful consideration of the scaling criteria. The requirements which must be met for a small-scale model to duplicate the behavior of a much larger reservoir prototype have been discussed by Leverett, et al,' Rapoport,2 and Geertsma, et al.3 According to these authors, the relative permeabilities to water, oil and gas and the dimensionless capillary pressures must be the must have the same values in the model and prototype. Furthermore, they point out that the viscosity ratios must have the same values in the model and prototype. In addition to these requirements, other scaling criteria are given which, when considered, usually dictate a much higher permeability in the model than exists in the reservoir. Since the more permeable model sands may have connate-water and residual oil saturations quite different from those in the prototype, the scaling requirements pertaining to the dependence of relative permeabilities and dimension l ess capillary pressures on saturation usually are not met. Also, if the model fluids are selected to give equal viscosity ratios in the model and prototype, one may find greatly different mobility ratios* in the two cases and, therefore, may expect grossly different flow patterns. For this reason, Craig, et al,' correlated the results of their model studies with mo- bility ratio rather than with viscosity ratio. As yet, however, no satisfactory method has been advanced which permits use of anything other than the scaling requirements outlined in the previously mentioned papers. The purpose of this paper is to present a method of developing a set of scaling criteria which permits different relationships between saturation and relative permeability or capillary pressure in the model and prototype. Rather than attempt to report scaling criteria for a variety of practical situations, this paper demonstrates by use of one simple example how the modified scaling criteria are derived.

By Hisaaki Takada, Atsushi Yoshida, Kazuo Satoh, Norikazu Nanko, Naoshichi Higashi

Kamioka Mine of Mitsui Mining & Smelting Co., Ltd. is the largest lead-zinc mine in Japan and is composed of two mines, Tochibora Mine and Mozumi Mine, which have daily production rates of 5,200 metric tons and 1,800 metric tons of crude ore respectively. In the mines, there are many massive pyro-metasomatic deposits which have been derived from the replacement of limestone. The deposits are composed of skarn minerals which mainly contain hedenberite. The country rock is generally hard and fine-grained gneiss. These deposits have been mined by means of the sublevel stoping method, induced block caving method and sublevel caving method at Tochibora Mine and mainly by the cut and fill method at Mozumi Mine. Since the 19601s, the trackless mining system has been introduced successfully into both mines, and is still promoted to be applied over wider areas. The underground hauling system is simplified remark- ably and much improved by adopting trackless ramps to the existing vertical and horizontal underground framework. Moreover, through the combination of the trackless mining system with the mining methods stated above, a notable increase in efficiency has been achieved. This is due to the high performance of the introduced machinery, reductions in man power of miscellaneous jobs, and also has enabled a highly efficient performance through its mobility. In addition, as it becomes possible to realize a flexible development to meet the irregularly shaped deposits and also becomes much easier to recover the remaining pillars by secondary mining, the extraction rate of ore has been improved considerably. With the introduction of the trackless mining system, the development method has been changed, thus former hand-hold leg-drills are now mostly re- placed by jumbo-type drills. Repair shops for Load-Haul-Dump machines also have been provided with an established service system. Reinforcement and rearrangement of the ventilation system has been carried out.

Jan 1, 1977

Gentlemen.-It is pleasant to be able to report that the year just closed has been a prosperous and successful one for the Institute. As is shown by the reports of the Treasurer and the Finance Committee, the business affairs of this organization are in excellent condition. With property valued at more than three-quarters of a million dollars, and with considerable sums in various funds and endowments, it is possible to spend on each member of whatever class $22.65 each year, more than the maxi- mum amount of dues received from any one, and substantially twice the average amount, $10.94, received from all. To do this has required close management and a strict regard for our limitations. In 1926, when the Budget was made up, the estimated expenditures for the work which it was felt the Institute must do exceeded the estimated receipts by some $14,000. At the close of the year, despite a number of unexpected decreases in receipts, it had proved possible to accomplish substantially all the work laid out and close the books with the usual transfer of initiation fees to the General Reserve, and still only reduce the cash balance $2,074.54. This was made possible by the hearty and loyal cooperation of the whole staff of employees and the extremely large amount of gratuitous service rendered by the officers, the members of the Divisions and technical Committees, and the membership generally. Even so it was impossible, because of limitations of funds, to undertake many things it is highly desirable for the Institute to do, and it was necessary to refuse the publication of important papers and committee studies, because of the lack of funds. PUBLICATIONS In an analysis of the income and expenses of the Institute published in the February issue of our Journal, MINING AND METALLURGY, it was pointed out that the largest item of expenditure is, as it should -be, for publications. Printing, binding, and distributing the various technical papers sent to the members cost in 1926 more than all the money received from dues, including the portion allocated as subscription to the magazine. Within the. year, the following volumes were printed and, with the exception of the second volume of TRANSACTIONS, which was mailed in January, were distributed : TRANSACTIONS, Volume 73, 1241 pages, covering papers on non-ferrous metallurgy, milling and concentration, non-metallic minerals, iron and steel, and the Institute of Metals Division papers read at the

Jan 1, 1928

By G. Derge, R. E. Grace

A S detailed studies of mass transport in hetero- geneous systems are made, a knowledge of the chemical diffusion coefficients in various liquid and solid phases is necessary to understand the kinetics of any total reaction. For example, in zone refining some information must be available about the diffusion coefficients of various species in the liquid and solid regions near the moving interface. In liquid-liquid reactions, of which slag-metal reactions are of particular interest to metallurgists, the diffusion coefficient of a transferring species must be known accurately in both phases in order to predict a transfer coefficient for the over-all process. Diffusion data for various elements in liquid iron and iron-carbon alloys have been roughly deter-

Jan 1, 1959

By A. N. Winchell

Petrographic studies of over 1400 rock and mineral samples, and studies of their field relations, show that there is a complete gradation between sandstone and limestone; the lime-silicate rocks were produced by recrystallization of limestone; mineralization and silicification occurred after silication and at considerably lower temperature; carbonation occurred at still lower temperatures. IN CONNECTION with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Bingham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance.

Jan 3, 1924

By Henry Rumfelt

8.1-1. History and Description of Shovels. The history of excavating machinery is not clearly defined but the machines seem to have been originally developed for dredging activities, principally involving rivers and harbors. The first, as far as can be determined, was a steam "spoon dredge" developed by Grimshaw of Boulton and Watt of Sunderland, England, in 1796. The land machine forerunner of the present-day power shovel was not developed until 1835. It was invented by William Smith Otis, a young partner of a Philadelphia contracting firm by the name of Carmichael and Fairbanks. The moving force behind this invention was the heavy activity in railroad construction. From this early start the power shovel has developed from steam powering to internal-combution-engine powering and to electric powering. In both directions it has developed to its present state of a finely engineered and precision-built tool. Through the interim the railroad-type shovel, about a half-swing arrangement designed especially for making railroad cuts and mounted on rails, was developed. The rail-mounted shovel gradually gave way to the full revolving shovel. It was high on the list in 1912 and was practically extinct by 1927. From the beginning, a few of the small revolving shovels designed primarily for the general contractors' market had found their way into quarry and mining operations. During this same period, the stripping shovel had been introduced-a 2 ½ cu. yd., 100-ton, full revolving stripping machine with a 41 ft boom. Although this shovel was designed especially for stripping, it was also used for heavy-duty, open pit mining service. In 1925 the heavy-duty, full revolving quarry and mine machine was developed. Strip mining shovels evolved through a somewhat separate path. Hand digging plows and mule-drawn slip scrapers were first reported used by Kirkland, Blakeney and Groves near Danville, Illinois for strip mining

Jan 1, 1968

By V. N. Mackiw

IN the process employed by Sherritt Gordon Mines Ltd. for the production of metallic nickel, a sul-fide concentrate is leached with ammonia and air under pressure. Following the removal of iron, copper, and other impurities, there remains a purified solution having the following analysis: 40 to 50 g per liter Ni, 200 to 400 g per liter (NH4)2 SO 4, and 20 to 30 g per liter NH3. Metallic nickel is reduced from this solution by hydrogen under pressure at 300' to 350°F in mechanically agitated autoclaves. A catalyst, ferrous sulfate, is required to initiate the first reduction. After the reduction, the depleted solution is discharged, leaving the metallic nickel in the autoclave. The nickel produced, being in a finely divided form, is used as a catalyst for the reduction of the next batch of solution. Upon repeated use the metallic nickel particles increase in size and become more compact, resulting in the production of a powder with higher apparent density. For this reason, each reduction is termed densification. Finally, when the burden of metal powder in the autoclave becomes too great to obtain effective agitation, both powder and depleted solution are discharged. The autoclave is then filled with fresh solution, ferrous sulfate catalyst added as before, and a new cycle started. The operation is described in earlier publications.1-6 A comprehensive historical review of the reduction of metals from solutions in general was given in a paper by Schaufelberger.7 The experimental data presented in this paper were taken from the work done in the Research Laboratory of Sherritt Gordon Mines Ltd. in Ottawa during the development of the process in 1951 and 1952. The results of the work were tested on a pilot plant scale in Ottawa in the period 1952 to 1953. Following laboratory and the pilot plant studies a commercial process has operated successfully since 1954 in the Nickel Refinery of Sherritt Gordon Mines Ltd. in Fort Saskatchewan, Alberta. General Experimental Technique The experiments were carried out in a stainless steel, 1-gallon, agitated autoclave designed and manufactured by Autoclave Engineers Inc. The inside dimensions of the vessel were 5 in. diam and 12 in. depth. The stirrer consisted of a 1/2 in. diam shaft 11 in. long fitted, with an axial flow type impeller (three blades bent to throw downwards) and a radial flow

Jan 1, 1958

THE primary interest in the subject of this chapter lies in the fact that various heats of steel made to the same chemical specification do not always have the same properties. We are referring here, of course, to properties inherent in the just solidified ingot and are not considering variations in properties caused by variations in subsequent mechanical or thermal treatment. The expression "made to the same chemical specification" is used because some of the variations in properties are due to variations in chemical analysis within the specified ranges of those elements commonly specified and determined. In plain carbon steels these elements are ordinarily not more than five: carbon, manganese, silicon, phosphorus, and sulphur. In alloy steels the special alloying elements also are specified and. determined. It might be thought that variations in properties due to such variations in ordinary chemical composition are to be expected, well understood, and hence not in need of discussion in this chapter. It will be considered here, however, that this phase of the subject is not always wholly clear. Furthermore, it certainly seems profitable to seek the explanation of anomalous properties in the ordinary chemical composition of the steel before looking into less well understood variables of open-hearth practice. It is sometimes surprising to learn that some puzzling variation in properties is caused merely by a variation in the ordinary analysis of the steel. This surprise is apt to be due not to general lack of knowledge of the effects of the composition of steel upon its properties but rather to the fact that we do not happen to have been previously much concerned with the particular property under consideration. For example, if we are accustomed to using S.A.E. 1035 bars for applications which depend chiefly on the stiffness, strength, and toughness of the steel in the as-rolled condition, we might quite logically develop the conclusion that variations in carbon content from 0.30 to 0.40 per cent are not significant. Then if we later have occasion to make heat-treated bolts of the same grade of steel, we may be surprised to

Jan 1, 1944