Search Documents

By Ralph Hayden

I. INTRODUCTION. IN the wet concentration of ores there is always a certain amount of very fine material with which to contend, and which invariably carries such quantities of value that the treatment of it is worth while; commercially. This fine material usually contains that portion of the ore which hinders the separation of the mineral values: namely, the colloidal material resulting from the decomposition of certain constituents of the ore. The object of this paper is to show what efforts have been made to solve the slime problem as it occurs in the concentrator of the Washoe

Jan 8, 1913

By Y. Fukunaka, Y. Kondo, Z. Asaki, S. Nakashita

The pyrite smelting process in which about half amount of sulfur is recovered from pyrite by thermal decomposition in an oxygen-free high-temperature combustion gas flow in the flash smelting furnace is being conducted at Kokkola Works in Finland. A mathematical model of this process was developed, and the rates of thermal decomposition and fusion of suspended sulfide particles in the reaction shaft of furnace was calculated. This model is thought to be appropriate because of a fairly good coincidence of the calculated length of reaction zone with the shaft height of the furnace at Kokkola Works. The calculated reaction zone in which the thermal decomposition and fusion of sulfide particles occur becomes longer when pyrite particles of larger sizes are fed. The feeding rate of pyrite particles and the gas velocity at the nozzle exit are also the important operating factors. These two factors are closely related to the volume fraction and the residence time of suspended particles in the gas stream, and the optimal combined levels of these factors at which the length of reaction zone becomes minimal were obtained.

Jan 1, 1976

By Norman Brown, J. V. Rinnovatore

It was found that a shear stress applied during the recovery had no effect on the amount of recovery if the stress was less than the instantaneous yield point irrespective of the direction of the stress. Large ajplied stresses during recovery had a marked effect, which depended on the direction of stressing. Single strain reversals at -72°C not only produced the Bausch-inger effect but also increased the flow stress. The increase inflow stress was attributed to vacancies, which have appreciable mobility at -72 °C. THEORIES I-' of recovery suggest that the internal stress field of the dislocations plays an essential role. Most investigations of recovery use time and temperature as the independent variables; however, here stress has been introduced as a variable in two ways: 1) by varying the internal stress field according to the amount of strain prior to recovery and 2) by applying an external stress during recovery. Tannen- baum and Kauzrnann studied the effect of applying a stress during recovery by measuring the change in creep rate after recovery; they found that stresses as high as 95 pct of the creep stress had no effect on recovery. Earlier, Wood and scrutton6 showed that an applied stress during creep increased the rate of poly-gonization. The experiment by Wood involved poly-crystalline aluminum whereas Tannenbaum and Kauzmann used a single crystal of zinc. In this investigation, zinc single crystals were used and deformed in a manner to prevent polygonization. Thus, the main difference between this investigation and that of Tannenbaum and Kauzmann is the use of the stress-strain curve instead of creep rate as the index of recovery. In addition, the applied stress during recovery varied

Jan 1, 1961

By George F. Weaton

Mining differs from the ordinary industry in that most industries and enterprises have an indeterminate life, apparently perpetual, and therefore, are not called on to replace the original investment. In mining, however, when the ore bodies are mined out, there is nothing left, The original capital investment must, therefore, be returned to the investor by the time that the profitable life of the mine is ended. When the operating company makes no provisions for perpetuating its life by investing a portion of its earnings in other properties, the usual procedure is to pay the investor, periodically, a dividend sufficiently larger than the risk return on his investment to enable him, if he reinvests this overplus at a safe rate of compound interest, to replace his original capital by the time the mine is exhausted. This overplus constitutes a return of invested capital. In estimating the value of a mining enterprise, the work leading to the final result may be divided into two parts. The first is the examination of the property to determine ore reserves, mining costs and profits, financial requirements and future prospects. Whatever conclusions are reached in this phase of the work depend on the experience, thoroughness and integrity of the examining engineers. The second is the calculations pursuant to the field examination.

Jan 5, 1973

By E. J. Roberts, E. B. Fitch

Most classifiers in use today are, in function, settling pools. A fluid suspension of particles is passed through a pool at such a rate that only a fraction of the particles-the coarser fraction-has time to settle out of suspension. The rest are carried on out of the pool as overflow. The most fundamental way in which such classifiers differ is in the mechanism used to remove the settled particles from the pool. The particles may gravitate from the pool, as in the various sand cones, or they may be conveyed mechanically from the pool by drags, spirals, or reciprocating rakes. The mechanism of settling pool classification and its limitations are discussed. A method for calculating countercurrent classifications is presented. The practical validity of the calculation method has been confirmed through 20 years of use within The Dorr Co. During this time it has been used on diverse feeds and has been checked against many types of settling pool classifiers, with close agreement in nearly every case. Excellent elimination of third critical mesh particles and finer ones may be obtained in a countercurrent classifications series where all stages separate at the same mesh, but elimination of first and second criticals is inherently limited. Spectacular elimination of all criticals may be obtained by arranging successive stages to classify at successively coarser mesh. Improvement in elimination is obtained at the cost of an increased internal recirculation, but this may be tolerable in many cases.

Nov 1, 1956

By W. J. Keep

Those who have observed the influence of various elements upon cast-iron will be interested in the methods used by us to form the several series of test-bars, which form the basis of the conclusions presented in this paper. We found that we could not, by adding ordinary white stickphosphorus to molten iron, produce bars which would exhibit to the eye the peculiar influence of phosphorus. By melting wrought-iron drillings with red phosphorus, Mr. H. S. Fleming produced in his laboratory 10 pounds of phosphide of iron, containing 10.22 per cent. of phosphorus. With this we made two series of test-bars, the first with our white-base iron, and the second with our FLM gray-base iron. Before the time of making these bars we had been unable to procure regularly made pig-iron which contained enough phosphorus to permit of the production of

Jan 1, 1890

By R. G. Mallon, A. E. Lewis, R. L. Braun, C. J. Sisemore

Large ore-bodies, too deep to mine economically by underground methods, may be mined using nuclear explosives and a high pressure leaching technology. Breaking of a hypothetical ore-body with a series of nuclear explosives is described. The leaching would be accomplished by pumping oxygen into the flooded rubble under the normal hydrostatic pressure. The injection of oxygen gas into the bottom of the rubble chimney induces a circulation of the solutions which carries dissolved oxygen to all parts of the chimney. Copper and other metals would be recovered from the solutions by solvent extraction as they are circulated through a surface plant in a closed system. This provides for control of pH as well as containment of radioactivity. Radioactivity levels in the solution are low, and no radioactive impurities are expected in the copper. This technology will allow production from deposits too deep to be of interest with present technology and will reduce or eliminate some environmental effects of conventional mining, such as open pits, mine dumps, tailings ponds, and SO2 effluent. Close proximity of cities and towns is a limitation because of seismic damage. The technology requires further development for commercial application, and exploration targets must be enlarged to include deeper deposits, before the technology can be applied on a large scale.

Jan 1, 1974

By E. G. Leonardon

THE object of this paper is to describe briefly the practical results obtained in several problems of civil engineering by resistivity measurements of the underground. It is intended for the mining engineer, as well as for the construction engineer; the stratigraphical problems discussed are general and frequently are encountered in mining exploration. Resistivity measurements have been used in mining and oil exploration for a number of years.1 Their introduction in the field of civil engineering, on the contrary, is rather recent. It was applied for the first time in the spring of 1928 near Littleton, N. H., in the survey of two dam sites for the New England Power Assn .2 Since then, the geophysical firm with which the author is connected has had an opportunity to develop this field of activity, and more than 20 investigations at dam and tunnel sites have been carried out in the United States and Canada. A part of this work has been verified by underground or drilling exploration. This paper deals with but a few of the results, which we are permitted to make public now. The theoretical and technical sides of the processes employed will not be discussed; they have already been described in various technical. .publications. A few general points will be mentioned, to make clear the practical examples given.

Jan 1, 1931

While mining silver at Butte in 1882, Marcus Daly is reputed to have told his partners in The Anaconda Silver Mining Co., "It looks rather gloomy. The vein is running into copper." Recently, The Anaconda Co. authorized an $11 million expenditure to be made over the next five years to ensure their "running into copper" at deep levels for many more years. The new development program is designed to permit both deeper and more widespread selective mining in "the richest hill on earth" by means of additional shaft-sinking, reactivating closed mines, and establishing new haulageways and centralized hoisting facilities. Historically a deep level selective mining camp, Butte will now continue its uncommon use of three main types of mining methods at one camp-selective mining, block caving, and open pit mining. It was thought by some people that the construction of the Kelley shaft and the subsequent beginning of block caving operations in 1952-outgrowth of the Greater Butte Project-signaled the end of stope mining of high-grade ores at depth. This feeling became more pronounced when, in 1957, the Berkeley open pit commenced operations. During recent years, the tonnage of ore mined selectively underground has decreased, but the new program will maintain the position of selective underground mining in the overall picture of the Butte operations for many years to come.

Jan 7, 1960

By Michael Tenenbaum

RECENT researches on the reduction of iron ores have stimulated interest in the effect of increased pressures within the iron blast furnace. From a physicochemical viewpoint, it seems logical to suppose that the increased pressure would increase the rate of reduction of the iron ore within the furnace. This increased reaction velocity would in turn be reflected in an increase in the output of the blast furnace. Any sub-stantial effect of elevated blast-furnace pressures should accordingly be of both technical and economic interest to the operator. It is doubtful whether it is possible to increase the pressure in the stack of the blast furnace beyond two or three atmospheres without incurring severe mechanical difficulties. The benefits to be procured by elevations in pressure must therefore be restricted to pressures below two, or at the most, three atmospheres. Within this range it would seem both economically and mechanically feasible to modify the present design of the upper portion of the blast furnace to accommodate these more stringent operating conditions. This investigation was undertaken to study the effect of moderate pressures on the rate of reduction of iron ore with hydrogen. The use of carbon monoxide is contemplated for later work. Although any results that are obtained in the laboratory cannot be interpreted directly in terms of large-scale commercial operations, it is possible, through such an investigation, to ascertain the order of magnitude of the effects of higher pressure. A more quantitative conception of the effects that would result from the use of increased pressures in the modern blast furnace is needed.

Jan 1, 1939

By Sir Lowthian Bell

WITH the exception of air and water, it is open to question whether there is any form of matter which the human race could less easily spare than iron. Short of going the length of asserting that, without this metal for an anchor or steel for the compass, the adventurous navigator could never have crossed the wide Atlantic, we may credit the locomotive' and the steamer, and hence iron, for that sequence of events which has peopled North America with the

Jan 1, 1891

By A. A. Janke, G. J. Vogel, W. M. Swift

The combustion of fossil fuels in a fluidized bed of calcined limestone particles is a potentially efficient and economically attractive process for the generation of steam for electric power production and other uses. The process results in greatly reduced emissions of both sulfur oxide and nitrogen oxide pollutants. Development work, evaluations, and design studies are being carried out by various organizations under contract with the Department of Interior (Office of Coal Research, OCR) and with the U.S. Environmental Protection Agency, (EPA). The Atomic Energy Commission's Argonne National Laboratory is one of the principal participants in the development program under interagency agreements with EPA and OCR. The principal reasons for developing fluidized-bed combustion, its advantages and disadvantages over conventional combustion methods, and some of the potential applications of the process are covered in this paper. The participants in the multiorganizational program, the sponsoring agencies, the general status of development of the overall project, and the chief program areas that still require resolution are discussed. The main features of the program of work at Argonne National Laboratory and the results achieved so far are also included.

Jan 1, 1976

By G. C. Bateman

THE Workmen's Compensation Act of Ontario was passed in 1915 and Miners' Phthisis was added to the list of compensable industrial diseases in 1916. Under this provision of the Act only about two cases were compensated per year. In 1924, The Department of Public Health made a survey of miners in the four principal camps-Sudbury, Porcupine, Kirkland Lake and Cobalt-and the survey indicated that an alarming proportion of the men exposed to dust had silicosis in one or other of its several stages. A number of conferences were held between representatives of the Department of Mines, the Department of Public Health, the Compensa-tion Board and the mine operators. The operators were advised that in the earliest stages of silicosis there was no physical disability and if men in that stage were removed froni underground there would be little danger of permanent disability. They were further advised that if active steps were taken at once to compensate men that had some real disability and remove from the mines men in the early stages of silicosis, the first cost would be the greatest and thereafter their liability should decrease. As a result of this advice, and having at that time no reason to doubt the findings of the survey, the operators agreed to do all that was asked of them and cooperate with the Government in the steps believed neces-sary to meet the situation, and to provide compensation for the men affected.

Jan 1, 1937

By T. B. Counselman

THE importance of concentration of iron ores too low in grade to be smelted direct is shown by Table I, showing 1940 ship- [ ] ments from the Lake Superior district. Canadian ores are omitted. [ ] Only in Minnesota is concentrating, other than crushing and screening, practiced at present. Tonnage produced by various methods of concentration is shown in Table 2. The curves in Fig. I show the gradual increase in tonnage of concentrated ores shipped, compared with total shipments from Minnesota. Most of the concentration work is performed on the Mesabi Range. This range is about 100 miles long, and not over 3 miles wide from the line at which the formation tapers out to a feather edge on the north to the place on the south at which, some 600 ft. thick, it is overlain with slates. CLASSES OF ORE The Mesabi Range contains three classes of iron ore. First is the unaltered taconite, or banded iron-bearing chert. It is estimated that there are some 60 billion tons of this material, which contains, roughly, 25 to 30 per cent iron. This material is virtually untouched, since no commercially successful method has yet been found for concentrating it to a grade suitable for the blast furnace. Intensive experimental work is in progress, and the problem is gradually being solved. In 1922 the Mesabi Iron Co. spent several million dollars erecting a large-scale pilot plant for concentrating and sintering the magnetic taconites on the east end of the range. An important tonnage of high-grade sinter was shipped to lower lake furnaces, proving that the taconite can be concentrated to a satisfactory grade. The costs, with equipment and methods then in use, were too high for

Jan 1, 1941

By H. C. Rolseth, J. J. Calaman

6.4-1. Principles of Operation. The jet-piercing process is a patented thermal process which depends upon a characteristic of the rock which is termed spallability. In its simplest terms, spalling is considered as decrepitation resulting from differential expansion of rock crystals due to thermally induced stresses. The number of individual properties influencing the spalling characteristics of rock are so numerous and their interaction so complex that the only truly reliable way to ascertain the spallability of rocks under thermal shock conditions is to expose them to these conditions. However, laboratory and field work have determined the principal thermal, physical, and mechanical properties of rock which affect spallability (10, 18). The approximate relationship between spallability and these characteristics is as follows: [ ] where To is the critical temperature at which, it is believed, a rock becomes elastic or sufficiently plastic to prevent further spalling action. Thermal diffusivity takes into account the amount of heat used in saturating the medium itself during the migration of a heat front. The rate and degree of dimensional changes which influence the spalling tendency of the rock will depend upon the characteristic of the heat gradient in the rock. The greater the spalling tendency, the higher the piercing rate. Those properties most favorable to a high degree of spallability are: 1. Large linear thermal expansion at temperatures below 700°C. 2. High thermal diffusivity at temperatures below 400°C. 3. Equigranular interlocking structure with little or no fine-grained clay or mica alteration products. 4. No significant amounts of soft, low-melting, or elastic mineral or materials which yield after thermal decomposition.

Jan 1, 1968

By Richard Miller

The investigations of large-grained specimens carried out by Polanyi and Schmid,1 Sykes,2 Goucher,3 Yamaguchi,4 Gough, Cox, and Sopwith,5 Carpenter and Elam,6 Aston,7 and others have shown qualitatively that grain boundaries restrain the deformation of adjacent crystals. But whether or not the influence of the grain boundary is confined to the glide planes intersected by the boundary has not been demonstrated in any of these investigations, nor has there been carried out any quanti-tative analysis, of the influence of a boundary on the deformation of a crystal. Indeed, the specimens employed in the previous work con-

Jan 1, 1934

By Arthur Taggart

FOREWORD THE tests herein described are part of an extended series of experiments, performed by the authors together with J. F. McClelland and L. W. Bahney, on the reclamation of metallics from foundry and manufacturing-plant scrap. The most obstinate problem encountered was the proper cleaning of the metal. INTRODUCTION In the manufacture of brass and brass products the weight of the finished product leaving the plant is much less than the total weight of copper and zinc entering. A small part of this discrepancy is due to the unavoidable oxidation of the metals in melting, but by far the largest part of the loss is in the form of metallic particles of copper, zinc, and brass. These losses occur principally at three points in the process: (a) in the casting-shop ashes; (b) in the slags from furnaces melting scrap brass; (c) in material spilled on the floor throughout the manufacturing process. The amount of these products in some plants is nearly 100 tons per 24 hours. Casting-shop ashes contain the metal spilled from the crucibles during melting and pouring, and the metal included in the slags formed in the melting process. The ashes also contain pieces of broken crucibles with adhering metal; 20 to 30 per cent. of unburned coal is also present. The metal in casting-shop ashes contains clean pieces of zinc or copper ingots weighing 1 to 2 lb., jagged pieces of metal of all shapes ranging in size from several inches down to the finest dust, and shot and botryoidal shapes ranging in size from 2 or 3 in. down to 0.01 mm. or less in diameter. Slags from furnaces melting scrap brass contain metal in the form of small shot.

Jan 2, 1916

As reported in Drift last month demolition of old buildings on the 47th St. site has been completed, and detailed plans and studies for the new structure are well underway. As this issue was being sent to press the $5 million industry- business phase of the fund campaign had passed the half- way mark toward its goal. Target date for the building program is 1960.

Jan 5, 1958

By Ulrich H. Roesler

RECENTLY, C. Zener1 published a new thermo-dynamic treatment of the a/y transformation in iron alloys. His interpretation differs from the previous theories2-0 ainly through the separation of the free energy difference, Ga—G, into two additive

Jan 1, 1957

By E. A. Wieselmann

This chapter presents a successful approach for achieving mine entry stability at the Cane Creek potash mine by the utilization of closure measurements. The mine is located in southeastern Utah (Fig. l). Mining is being conducted at depths in excess of 3000 ft under structurally complex geologic conditions typical of the Paradox salt basin. The closure measurement systems described have definite application for determining relative entry stability in other nonelastic rocks which are similar in behavior to potash. Similar types of closure measurements have been taken in various underground openings throughout the United States, Canada, arid Europe. Application of this closure data has previously met with varying degrees of success as a tool for design of under- ground openings in both elastic and nonelastic media.1-32 Closure measurements can be made easily and economically and they provide a practical solutiori to a practical problem. They are in-situ measurements which do not necessarily require laboratory correlation. Simple closure measurements have special significance in potash because "steady-state" ' closure rate, or creep, of the entries is measured. These closure rates can be utilized because nonelastic media such as potash will never achieve absolute stability around a mine entry. The potash will tend to creep or deform until all entries are closed and the overburden stress is redistributed over what was previously the mine area. The time for this ultimate effect to occur is dependent on a number of mining and geologic variables. Percentage of mine extraction, mining

Jan 1, 1972