Search Documents

By A. S. Odeh

The mechanism of two-phase flow in porous media has been a subject of wide controversy. One of the properties essential for understanding the dynamic behavior of two-phase flow is relalive permeability. Relative permeability to a certain phase is defined as the ratio of the effective permeability of that phase to its permeability when it is the only fluid present and powing. In this research, a theoretical analysis was made to determine the effect of viscosity ratio between the non-wetting and the wetting phase on relative permeability. Experimental work was conducted to test the validity of the derived equations. The experiment was conducted on four natural cores. Four oils were used as the non-wetting phases with a viscosity range of 0.42 to 71.30 cp and two wetting phases with a viscosity range of 0.86 to 0.96 cp. Oil and bring were made to flow simultaneously at various ratios, and relative permeability curves were constructed. A total of eight relative pertileability cycles representing eight viscosity ratios were run oil each sample. It was found that relative permeability to the non-~cletting phase varies with viscosity ratio. The relative effect of this variation on relative permeability values was a function of the sample's single-phase permeability, decreasing with its increase. It was concluded that, for .samples of single-phase permeability over I darcy. the effect of viscosity ratio could be disregarded, and relative permeability would be, in effect, a function of satrtration only. INTRODUCTION Two-phase as well as multiphase flow occurs in many fields of science. This type of flow is of particular interest in petroleum production. The knowledge of relative permeability, which describes the dynamic behavior of two-phasc as well as multiphase flow, is essential for solution of problems arising in that field. Thc relative permeability ot a porous medium to a given phase in multiphase flow. is generally considered to be only a function of the saturation of that phase, independent of the properties of fluids involved and ranging in value from zero to unity. Work by Leverett' and Leverett and Lewis' apparently supports this concept. In his experiments Leverett used a clean, packed unconsolidated sand of high permeability (3.2 to 6.2 darcies) with two phases (water and oil) flowing and a viscosity ratio range of 0.057 to 90.0. His results showed that the wide range of viscosity had practically no effect on relative permeability-saturation relationship. Recently accumulated evidence from work performed by several laboratories and a paper by Nowak and Krueger,2 in which relative permeability to oil of a few core samples in the presence of interstitial water was considerably greater than single-phase permeability to water, cast some doubt on the conclusions reached by Leverett' and subscribed to by a large number of individuals in the oil industry. One explanation advanced to explain this behavior states that it is caused by the variable extent of hydra-tion of clay minerals present in the sand. The greater the water saturation, the greater will be the area of contact between water and clay minerals; therefore, the greater will be the extent of swelling with corresponding reduction in permeability. Yuster4 presents another explanation for the recently accumulated evidence. Utilizing Poiseuille's law, he analyzed concentric flow in a single capillary where the non-wetting phase flows in a cylindrical portion of the capillary and concentric with it. The wetting phase flows in the annulus between the non-wetting phase and the capillary wall. The equations obtained indicate that relative permeability to the non-wetting phase is a function of saturation and viscosity ratio. Although Yuster's equations show that fractional rel-ative permeability to oil could be greater than unity, as was indicated by the data of Nowak and Krueger,1 they failed to present an explanation to the experimental data of early investigators such as Leverett.1 Due to the importance of relative permeability in understanding the flow behavior of petroleum reservoir fluids, this work—theoretical as well as experimental —was undertaken to determine whether relative permeability is a function of saturation only as was concluded by Leverett1 or a function of saturation and viscosity ratio as was theorized by Yuster.4 THEORETICAL ANALYSIS An equation will be derived for the rate of oil flow through a porous medium that is initially filled with water. Based on this equation, an analytic expression for relative permeability will be developed. The porous medium will be assumed to consist of .straight circular capillaries of different radii. It will also be assumed that there are no interconnections among the capillaries and no mass transfer across the oil-water interface. Consider a porous sample initially saturated with a wetting phase (water). As a non-wetting phase (oil) is

By John C. Martin

The discovery of a new gas reservoir demands that the planning of a sottnd well-spacing program be initiated early in the development stage. It is the purpose of this discussion to illustrate by actual field examples the application of basic well-spacing principles, previously developed for oil reservoirs, to the problem of well spacing in natural gas fields. These studies are presented for the field use of geologists and engineers who are concerned with the initial planning of the proper development of the newly discovered gas reservoir. INTRODUCTION The phenomenal growth of a vigorous natural gas industry emphasizes the increasing importance of natural gas as a source of energy, fuel, and raw materials to our nation's economy. Since 1945 marketed production of natural gas for the U. S. has increased 21/2 times to a record high of 10.6 trillion cu ft during 1957. As major participants in the gas industry, we share an added interest to develop and produce our natural gas reserves with constantly improved efficiency. The subject of well spacing is vitally important to the gas industry, for the well itself plays a significant role in the development of the natural gas reservoir and in control of the recovery process. Maximum utilization of wells is an integral part of sound conservation practices. The discovery of a new gas reservoir demands that careful choice of well location and well spacing be made and that the planning of a sound well spacing program be initiated early an the development stage. With the drilling of the first development well, efforts of the geologist and engineer must be directed toward acquisition of adequate technical evidence upon which a firm recommendation for a spacing program may be based. With this technical appraisal as a foundation, operators and state regulatory agencies jointly can go far in providing a framework for sound development of gas fields to achieve a program of conservation that avoids the unnecessary well. WELL-SPACING CONCEPTS Through laboratory and field investigations of the mechanism of the recovery of oil and gas, of fluid behavior, and of effective control of reservoir and well, a crystallization of ideas regarding reservoir behavior has emerged as a well-developed technology. Associated with a better understanding of the fundamental principles underlying reservoir and well behavior has been the growth of concepts concerning the role of wells and their spacing in the development and operation of an oil or gas reservoir. In addition to serving as outlets for the withdrawal of fluids from the reservoir, wells are recognized as having two other important functions: (1) providing access to the reservoir to obtain information concerning the characteristics of the reservoir and its fluids, and (2) serving as a means by which the natural or induced recovery mechanism may be effectively controlled. Beyond a minimum number of wells required to fulfill these two functions, additional wells will not increase recovery. With particular emphasis upon well spacing in oil reservoirs, many studies of the well spacing-recovery relationship have evolved the concept that the ultimate oil recovery is essentially independent of the well spacing.' These fundamental concepts are no different when regarding the role of wells and their spacing in the natural gas reservoir. They are equally applicable to the consideration of well spacing in gas reservoirs. For the gas reservoir, the problem of well spacing then revolves around the question of drainage and the degree or extent to which a well may drain gas from its surrounding reservoir environment. Theoretical and Experimental Work During the past 30 years, theoretical and experimental work carried on to study the physical principles involved in the flow of fluids through porous media has shed light upon the matter of drainage. Fundamental mathematical equations have been derived to describe the mechanism of flow of oil and gas through porous rocks. With the recent advent of high-speed digital computers, attempts have been made with mounting success to develop solutions, employing numerical techniques, to mathematical expressions that describe more rigorously the physical behavior and mechanism involved in the unsteady-state flow of compressible fluids, such as a gas, through porous rock. In 1953, Bruce, Peace-man, Rachford and Ricez published a stable numerical procedure for solving the equation for production of gas at constant rate. The results of these calculations are significant with respect to this matter of drainage, for they indicated (1) that depletion of the gas reservoir resulted in a drop in pressure at the extremity of the

By Paul F. Kerr, Raymond F. Robinson

Uranium mineralization occurs in the footwall of the Sunshine vein from the 2900 to the 3700 level. Veinlets of uraninite associated with pyrite and jasper have been so extensively divided and recemented that units more than a few feet in length are seldom observed. The wall rock is St. Regis quartzite of the Belt series. The age of the uraninite, on the basis of isotopic analyses, is 750 * 50, which agrees with geological data suggesting that phases of the Sunshine mineralization are pre Cambrian. THE Sunshine mine in the Coeur d'Alene district, Idaho, is well known for its silver-bearing veins but prior to the summer of 1949 had not been recognized as a possible source of uranium. At that time, during a geiger counter reconnaissance by T. E. Gillingham, R. F. Robinson, and E. E. Thurlow, high radioactivity was noted and radioactive specimens were collected from the footwall of the Sunshine vein.' The detection led to the identification of uraninite-bearing veins, since explored jointly by the Atomic Energy Commission and the Sunshine Mining Co. After the occurrence was noted, the geology of the uranium deposit was studied by the Sunshine staff, and a laboratory examination of the ores was conducted at Columbia University. Several types of laboratory work were undertaken. Differential thermal curves were made of selected siderite samples and results from many more were secured through the work of Mitcham.2 X-ray diffraction and X-ray fluorescence analyses were employed on uraninite, jasper, and siderite. Chemical analyses were made through the cooperation of the Division of Raw Materials of the Atomic Energy Commission. General Geological Features Several silver-bearing veins cut the overturned north limb of the Big Creek anticline as mapped by Shenon and McConne1,³ while the Osburn fault, a long-recognized regional feature about a mile away, marks the north boundary of the Silver Belt. The Sunshine vein, Fig. 1, has a south dip more or less parallel to the 60" axial plane of the fold and cuts rocks of the Belt. Series, starting with the Wallace formation near the surface, continuing downward through the St. Regis formation, and probably extending into the Revett quartzite which lies below the bottom or 3700-ft level. The limb of the anticline is locally modified by secondary folds, one being prominently exposed in the uranian area along the Jewel1 crosscut near the Sunshine vein. Crumpling of the limb resulted from compression which formed the anticline and probably preceded the faults in which the vein deposits accumulated. Evidence of drag along these faults points to reverse movement in the uranium-bearing area and elsewhere. This is true of major faults in the mine workings, and the majority of faults which can be mapped, as pointed out by Robinson.' The St. Regis formation, as measured in the mine, appears to have an initial thickness of some 2000 ft, but the apparent thickness due to thickening during folding is some 3400 ft. Along the Sunshine vein the purple and green rocks characteristic of the Wallace formation in the nearby Military Gulch section p. 37 of ref. 5) have been completely bleached because of introduced sericite. Hydrothermal solutions acting on the wall rock have substituted for the original color a pale greenish cast, although no pronounced mineralogical change has resulted, as Mitcham has observed.' The silver and the uranium depositions appear to belong to distinct epochs resulting from several periods of emplacement. Likewise, multiple periods of deformation account for the faulting. Uraninite is generally associated with silicification, while silver . mineralization accompanies carbonate veins. Rarely, uraninite may be found in a matrix of siderite. Ordinarily uraninite formed prior to ar-gentian tetrahedrite. Where clusters of veins form a stockwork, uraninite-jasper veins often favor one trend while tetrahedrite-siderite veins favor another. During deformation, brecciation of the St. Regis quartzite provided openings between broken rock fragments for precipitation from vein-forming solutions. Fractures due to major breaks were filled during the first stages of vein formation, while later deformation displaced the first veins and provided new channels along which further mineralizing solutions proceeded. The uraninite veins, as the first formed, have suffered fracturing, displacement, and segmentation. Uranian vein segments uncut by faults and more than a few feet in length are rare or nonexistent. Siderite veins are more massive and often extend without a break for tens and even hundreds of feet. In general they show much less segmentation. While the siderite is usually later, there is an overlap in the periods of deposition, some earlier siderite veins being extensively segmented in much the same way uraninite veins have been broken. Vein silica is more extensively distributed than the uranium and iron mineralization it carries. Along the vein course concentrations of uraninite frequently fade away and barren white quartz continues, the transition often occurring within a few feet along strike or down dip. An example appears on the 3700-ft level where a uraninite vein, see Fig. 2a,

Jan 1, 1954

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

By I. R. Kramer

Studies of the effect of size of the specimen on the change of slopes of Stages I and 11 by surface removal showed that the change of Stage I was independent of size with respect to the polishing rate; however, the change in the slope of Stage 11 with polishing rate increased directly in proportion to the surface area. The removal of the surface during the test affected the plastic deformation characteristics of gold, aluminum, and zinc single crystals and polycrystalline aluminum. The apparent activation energy of aluminum was found to be decreased markedly by removing the surface during the deformation process. In previous papers1-3 it was shown that the surface played an important role in the plastic deformation of metals. By removing the surface layers of a crystal of aluminum by electrolytic polishing during tensile deformation, it was found that the slopes of Stages I, II, and III were decreased and the extents of Stages I and II were increased when the rate of metal removal was increased. By removing a sufficient amount of the surface layer after a specimen had been deformed into the Stage I region, upon reloading, the flow stress was the same as the original critical resolved shear stress and the extent of Stage I was the same as if the specimen had not been deformed previously. The slope of Stage I was decreased 50 pct and that of Stage 11 decreased 25 pct when the rate of metal removal was 50 X 10"5 ipm. These data show that in Stage I the work hardening is controlled almost entirely by the surface conditions, while in Stages 11 and III both surface conditions and internal obstacles to dislocation motion are important. It appears that during the egress of dislocations from the crystal, a fraction of them becomes stuck or trapped in the surface regions and a layer of a high dislocation concentration is formed. This layer would not only impede the motion of dislocations, but would provide a barrier against which dislocations may pile up. In this case, there will be a stress, opposite to that of the applied stress, imposed on the dislocation source and dislocations moving in the region beyond this layer. It has been found convenient to refer to this layer as a "debris" layer. The "debris" layer may be similar to the dislocation tangle observed by thin-film electron microscope techniques.4 Reported in this paper are the results of studies on the effects of removing the surface during plastic deformation on aluminum crystals of various sizes. The effects of the surface on the yield point behavior of gold and high-purity aluminum crystals as well as the creep behavior were also determined. The effects of surface removal on polycrystalline aluminum (1100-0 and 7075-T6) are also reported. EXPERIMENTAL PROCEDURE For those portions of the investigation involving creep and tensile specimens, single crystals, having a 3-in. gage length and a nominal 1/8-in. sq cross section, were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The single crystals were prepared from materials which had initial purities of 99.997, 99.999, 99.999, and 99.999 pct for Al, Cu, Zn, and Au, respectively. The aluminum specimens for the size effect studies were prepared through the use of a three-tier mold in which crystals having a cross section of 1/8, 1/4, and 1/2 in. were grown from a common seed. The mold design was arranged so that one 1/2-in. crystal, two 1/4-in. crystals, and four 1/8-in, crystals of the same orientation could be cast. With this technique, it was possible to obtain only one set of crystals with the same orientation. Because of this limitation, it was not possible to determine both the changes of extent and slope of the various stages since a large number of crystals of the same orientation would have been required. Instead, only the change of slope as a function of the rate of metal removal was studied by abruptly altering the current density of the electrolytic polishing bath at various strains within the regions of Stages I and 11. The experimental techniques used for the tensile studies were essentially the same as those used previously.1,3 The specimens were deformed in a 200-lb Instron tensile machine, usually at a rate of 10-5 sec-5. A methyl alcohol-nitric acid solution was used as the polishing bath for aluminum. The temperature was maintained constant within ±0.l°C by means of a water bath. The tensile machine was

Jan 1, 1963

By L. W. Holm

Laboratory flooding experiments on linear flow systerns indicated that high oil displacement, approaching that obtained from completely miscible solvents, can be attained by injecting a small slug of carbon dioxide into a reservoir and driving it with plain or carbonated water. Data are presented in this paper which show the results of laboratory work designed to evaluate this oil recovery process, particularly at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi. Under these conditions CO2 exists as a dense single-phase fluid. It was found that a bank, rich in light hydrocarbons, was formed at the leading edge of the CO? slug during floods on long cores. Formation of this bank is probably due to a selective extraction by the C02 and, it is believed, partially accounts for the attractively high oil recoveries. In crddition to the efficient displacernerlt of oil from the pores of the rock by this process, the favorable rnobility ratio related to a C0 2-water flood also contributes to high oil recovery. A further advantage of this process is noted on limestone and dolomite rock, in that the CO1 reacts with the porous medium increasing its permeability. Flooding experiments were conducted on sandstone and vugular dolomite models. The results of this experimental work show the effect on oil recovery of type of porous medium, pore geometry, flooding length, and flooding pressure. The porosity of the cores and rilodels varied from 16 to 21 per cent and their pern~eabilities ranged from 100 to 200 md. A reconstituted West Texas reservoir oil, a West Texas stock tank oil, an East Texas stock tank oil and Soltrol were used to represent reservoir oils in this study. Oil recoveries ranging from 60 to 80 per cent of the original oil in place in these cores were obtained by CO2,-carbonated water floods at pressures between 900 and 1,800 psi, compared with conventional solution gas drive and water-flood recoveries of 30 to 45 per cent on the same cores. Oil recoveries greater than 80 per cent resulted frorn f1oods at pressures above about 1.800 psi. There high recoveries were noted from both the sandstone and the irregular Porosity carbonate cores. In all floods, additional oil was recovered by a solutiorr gas drive resulting from blowdown following the flood. Oil recoveries of 6 to 15 per cent of the original oil in place were obtained during this blowdown period. This additional recovery was found to be a function of oil remaining after the flood, decreasing with decreasing oil saturation. It was also noted that highest oil recoveries by blowdown were obtained when carborlated water rather than plain water followed the CO, slug. INTRODUCTION Miscible phase or solvent flooding processes, which are designed to increase oil recovery -from petroleum reservoirs, involve the injection of small quantities of a petroleum solvent into the reservoir, followed by an inexpensive scavenging fluid which is miscible with the solvent. Essentially complete displacement of oil from the pores of reservoir rock has been obtained by this technique. CO,, although not completely miscible with most reservoir oils at moderate pressures, is highly soluble in these oils at pressures above about 700 psi; there is appreciable swelling and reduction in the viscosity of oil when CO, is dissolved in it. Therefore, CO, could be expected to perform similarly to other oil solvents as a displacing agent. CO, is also highly soluble in water at elevated pressures, so water should be a satisfactory material to drive a slug of CO, through an oil-bearing reservoir. A favorable mobility ratio would be obtained through the reduction in viscosity of the oil and the use of water as a final displacing agent. A number of investigations of the use of CO, to improve oil recovery have been reported in the literature.2,3,4,5,6 These studies, however, have been conducted on uniform porosity sandstone at relatively low temperatures and pressures. The behavior of CO1 as a flooding agent at temperatures above its critical temperature could not be predicted adequately from these studies, particularly for the case of non-homogeneous rock. The purpose of this work was to evaluate the oil recovery efficiency of a process involving the injection of a CO2 slug followed by carbonated water, at reservoir temperatures above 100°F and in the pressure range of 600 to 2,600 psi, and to compare this process with conventional water flooding. The investigations were primarily designed to provide information on the efficiency of the process in irregular porosity carbonate rock. The effects of flooding path length, the presence of free gas, the type of oil to be recovered, and the amount of solvent required were also determined. The essential results of static phase behavior studies and experimen-

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By B. A. Wilcox, A. H. Clauer

The steady-state creep of TD Nickel NL + 2 001 pct TltOz) has been studied orer the telirperatve range 325&apos; to 1100O and the stress range 15,000 to 36,000 psi. At high temperatures (aboue 0.5 T& gran-boundary slzding is the )nost znportant )node of creep deformation, and the steady-state creep rate, is, can be related to stress and temperature by: where Q = 190 kcal pev mole and n has an unusually high value of 40. A creep mechanism based on cross slip of dislocations around The O2 particles can satisfactovily explain the low-temperature (T < 0.5 T,) cveep behavior, and the follo wing relation is applicable: Q, (a) is found to decrease from 57 to 46 kcal per mole as the stress is increased from 32,000 to 36,000 psi. THERE have been a variety of theories proposed to explain the influence of dispersed second-phase particles on the yield strength and flow stress of metals, and these have been reviewed recently by Kelly and icholson.&apos; However, only several attempts2"4 have been made to develop mechanistic treatments which characterize the creep behavior of dispersion-strengthened metals, and to date these have not been fully evaluated experimentally. weertman2 and Ansell and weertman3 proposed a quantitative creep theory for coarse-grairzed dispersion-strengthened metals, based on the concept that the rate-controlling process for steady-state creep was the climb of dislocations over second-phase particles, as suggested by choeck. The theory predicted that the steady-state creep rate, <,, was proportional to the applied stress, a, for low stresses and that is a4 o for high stresses. The activation energy for creep, Q,, was equivalent to that for self-diffusion, Qs.d., in the matrix. Some limited experimental evidence in support of this theory was obtained on a recrystallized Al-Alz03 S.A.P.-type alloy by Ansell and Lenel.6 Ansell and weertman3 also developed a semiquanti-tative theory for high-temperature creep of lineg-rained dispersion-strengthened metals in order to explain their results on an extruded S:A.P.-type alloy, which had a fine-grained fibrous structure. They suggested that the rate of dislocation generation from grain boundaries was the rate-controlling process, and fitted their results to the equation: where Q, was found to be 150 kcal per mole, i.e., QC- 4Q,.d. in aluminum. Similar high activation energies for creep7-&apos;&apos; and tensile deformation" of dispersion-strengthened alloys have been observed by other investigators for S.A.P.,&apos;" indium-glass bead omosites, and Ni + A1203 alls.&apos; There is no general agreement regarding the mechanisms involved in the creep of dispersion-strengthened metals, and this is due in part to the lack of detailed studies relating the structures of crept specimens to the mechanical behavior. The present investigation on thoriated nickel was undertaken with the aim of studying the structural changes which occur during creep of a dispersion-strengthened alloy and rationalizing the observed mechanical behavior in terms of the creep structures. EXPERIMENTAL METHODS The material used in this investigation was 1/2-in.-diam TD Nickel bar, which contained 2.3 vol pct Tho,. Obtained from E. I. duPont de Nemours & Co., Inc. The final fabrication treatment by DuPont consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fine-grained fibered structure with an average transverse grain size of -1 p and a longitudinal grain size of 10 to 15 p. Selected-area diffraction indicated that the fiber axis was parallel to (OOl), in agreement with the results of Inman eta1." All creep specimens were vacuum-annealed at 1300°C for 3 hr prior to testing. Transmission electron microscopy showed that the only structural change due to annealing was a slight decrease in dislocation density, confirming the reported high degree of structural stability.13 Furthermore, recrys-tallization or grain growth during creep was never observed. The structure typical of uncrept material (after the 1300 C, 3-hr anneal) is shown in Fig. 1. The grain boundaries are predominantly high angle and. although some areas show a tangled cell structure, the grain interiors are relatively dislocation-free. Individual dislocations are strongly pinned by the Tho2 particles; i.e., very rarely did dislocations move within a thin foil. The grey "halos" around some of the larger particles which protrude out of the foil surface arise from contamination in the electron microscoge. The Tho, particle size ranged from -100 to IOOOA, and the distribution is shown in Fig. 2. The technique used to obtain the data in Fig. 2 consisted of dissolving the nickel matrix in acid, collecting the Tho2 particles on cellulose acetate, and measuring about 1000 particle diameters in the electron microscope. Similar results were obtained by measuring about 600 particles in thin foils, an; the average particle size was found to be 2r, = 370A. Using the data in Fig. 2 (annealed structure), the mean planar center-to-center particle

Jan 1, 1967

By E. W. Johnson, M. L. Hill

Cold working of iron-carbon alloys was found to increase greatly the hydrogen solubility and to decrease the diffusivity at temperatures up to 400° C. These effects are increasing functions of both the carbon content and the degree of deformation. The hydrogen behavior is consistent with the idea that cotd working creates "traps", which are concluded to be microcracks in which the hydrogen is chemisorbed. Hydrogen embrittlement is explained by the Petch theory of metal crack surface energy loss due to hydrogen adsorption. HYDROGEN embrittlement of steel has been studied for many years and has been the subject of an extensive literature, but the mechanism of the effect has not been completely understood. The embrittlement is unusual in that the ductility loss is not accompanied by an increase of the yield strength, being primarily a decrease of the fracture strength alone. The loss of fracture strength is usually most severe in the temperature range between 0°and 100°C. Here the solubility of hydrogen in the iron lattice at ordinary H2 pressures is extremely low while the diffusivity is still quite high. From the relationships between the ductility and the hydrogen content, test temperature and strain rate, it is apparent that the hydrogen atoms causing the ductility loss difbse to and concentrate in small regions of the metal which are especially susceptible to the initiation and propagation of fracture. This hydrogen segregation apparently occurs after plastic straining has begun. Below 0°C the ductility loss persists only at low strain rates in confirmation of the view that the embrittlement is diffusion .controlled. The tendency of the embrittlement to disappear above 100°C can be explained by the increasing lattice solubility of hydrogen with rising temperature. A common view of hydrogen embrittlement of steel is that the hydrogen initially dissolved in the metal lattice diffuses to structural discontinuities and there precipitates as H2 gas at very high pressures which assist the external stress in causing premature failure.1,2 The idea of a high H2 pressure in equilibrium with ordinary amounts of hydrogen in steel at room temperature is due to observations of hydrogen behavior in fully annealed material, for which the Sieverts&apos; law constant relating solute concentration to H2 pressure is extremely small. Hydrogen-embrittled steel, however, is always plastically deformed to some extent, and therefore it is important that hydrogen embrittlement be explained primarily in terms of hydrogen behavior in plastically deformed material. Such an explanation is attempted in this paper. Previous studies of hydrogen in cold-worked steel have shown that both the solubility and the diffusion rate are significantly chaned when the steel is cold worked. Darken and Smith discovered that the amount of hydrogen absorbed from acid by cold-rolled steel at 35°C is many times greater than that absorbed by hot-rolled steel. They found also that the hydrogen permeability of the steel is unaffected by cold working. Keeler and Davis4 confirmed the high apparent solubility of hydrogen in cold-worked iron-carbon alloys at temperatures up to and even beyond the recrystallization temperature. They also found that this solubility increase accompanying cold work is a sensitive function of the carbon content, being absent when no carbon is present. The present experimental study was undertaken primarily to obtain an improved understanding of the behavior of hydrogen in cold-worked steel. Data were obtained on the effects of temperature, H, pressure, carbon content, and degree of cold work on the hydrogen solubility and diffusivity in iron-carbon alloys. These data have been helpful in elucidating the nature of the cold-worked steel structure as well as in providing information on the mechanism of hydrogen embrittlement of steel. EXPERIMENTAL Cylindrical specimens for hydrogen absorption and diffusion rate measurements were prepared from three iron-carbon binary alloys and a commercial SAE 1010 steel. The iron-carbon alloys were prepared by vacuum melting electrolytic iron with graphite in a magnesia crucible. The alloys were cast in vacuum as 2 1/2-in. sq ingots weighing about 20 lb each. The ingots were hot rolled (above 1900°F) to 5/8-in.-diam round bars and then cooled in air to room temperature. The resulting metallographic structure consisted of islands of fine pearlite surrounded by free ferrite. Chemical analyses of the materials are given in Table I. The 5/8-in. diam bars were turned to diameters such that cold reduction to the desired final specimen diameters would result in either 30 or 60 pct reduction in area (RA). The machined bars were then cold worked by swaging at room temperature

Jan 1, 1960

By Pierre Hines

THE. Owyhee Tunnels in eastern Oregon were started in the early part of 1930, and were completed early in 1932, with the excep-tion of the Magoffin contract. One tunnel is a large water tun-nel, and the other is a small water tunnel; each is approximately tour miles long. Modern equipment was used to full advantage, and remarkably fast time was made during the driving period. The ,J. F. Shea Co., con-tractors, of Portland, Oregon, have broken established records in the smaller tunnel. Their methods are described in detail. The time of a complete round has been reduced by intelligent handling of mechanical shoveling, and this article records some of the useful facts developed. Charles A. Shea (president of the J. F. Shea Co., and secretary of The Six Companies, Inc.) not only granted permission to publish this article, but placed the company&apos;s complete daily reports at the writer&apos;s disposal. These reports were made out to conform with previous records upon important tunnel work, and enable a comparison to be made of actual averages, rather than ideal cycles, or representative cycles. Gilbert Shea, present superintendent, has been helpful with time, criticisms, and corrections of the information presented. Morton S. Boss, superintendent during the first 15 months of the tunnel work, gave many hours of his time during two visits lasting over two weeks. The whole staff of the J. F. Shea Co. has given encouragement and assistance.

Jan 1, 1933

By J. L. LeBlanc, R. L. Lewis

This study presents an analysis of annular backpressure variations associated with controlled gas kicks and their pronounced effect on casing .strings and exposed under lying formations. A mathematical model describing the volumetric behavior of an extraneous gas as it is transported from reservoir to .surface conditions under changing temperatures and pressures has been programmed in a Kingston FORTRAN II language for digital computer analysis. The gases under investigation typify Gulf Coast reservoir gases within a 0.6 to 0.7 .specific gravity range. The program output has been substantiated by actual field cases. of gas kicks encountered in Gulf Coart we1l.s. The development of empirical equations for calculating suitable gamy deviation factors for unique temperatures and pressures was incorporated in the program to provide realistic solution.. An output listing of annular backpressures and corresponding equivalent fluid densities resulting at a predetermined critical depth (casing setting depth) and total depth for selected .stages of circulation is provided in a chronological .sequence. Additional information including reservoir pressure and temperature, kill rnrid density, produced gas or surface volume of the expanded gas intro vion, drill pipe and annular volumes can he obtained from the model. This paper illustrates that a precise knowledge of the volumetric behavior of extraneous gases in annular flow and its effect on equivalent fluid densities at a critical depth is significant and should receive .serious consideration in controlling threatened blowouts and in the design of drilling programs. Surface pressures in excess of formation limitations are a threat to zones of lost circula/ion and are potentially injurious to productive intervals. A knowledge of annular backpressure and equivalent fluid density profiles for probable gas kicks aids in a technological accomplishment of drilling programs and provides a .sale tolerance in the event a threatened blowout is encountered. Introduction Drilling operations are frequently interrupted when the drill bit penetrates permeable gas sands with reservoir CtfuJ manuscript was received in Society of Petroleum Engineers ofice Am. 1 1967. Revised manuscript received JuIy 7. 1968. Paper (SPE 1860) kae presented at SPE 42nd Annual Fall Meeting held in Houston. Tex., Oct 1-4, 1967. @ Copyright 1968 American Institute of Mining, Metallurgical, and Petroleum Engineem, Inc. pressures greater than that exerted by the drilling fluid. The differential pressures resulting permit an extraneous influx of gas into the wellbore. A suspension in drilling progress is necessary to restore fluid equilibrium throughout the system. Whether formation gas kicks originate unintentionally or by design, the prospect of a threatened or actual blowout exists and a method assuring a safe and effective well control procedure must be observed. A significant contribution to well control technology was advanced by Records et a1.l in 1962. Using the concept of transmitting a constant equivalent formation pressure at the point of intrusion, Records et al. introduced a calculation technique providing the annular backpressures encountered in a well control environment as a func tion of the volumetric behavior of a 0.6 specific gravity natural gas. In essence, the procedure outlined an annular backpressure schedule in terms of fluid volume circulated at different stages of a well control operation. A number of other publications2-&apos; proposing various techniques for controlling gas intrusions in a wellbore achieve pressure control essentially through maintenance of a constant bottom-hole pressure by surface choke adjustments. The subsequent pressure effects induced in the annulus unfortunately receive little emphasis. Due to the tedious and repetitive nature of annular backpressure computations, a theoretical solution by digital computer is introduced for predicting annular backpressure and equivalent fluid density profiles associated with controlled gas kicks. We point out the effects of volumetric behavior of extraneous gases in annular flow and related field phenomena on equivalent fluid densities at a critical depth. The investigation indicated that equivalent fluid densities at a critical depth are of significance and should receive consideration in the control of threatened blowouts and in the design of drilling programs. Theoretical Considerations The mechanism of vertical gas flow through an annulus is governed by the PVT properties of the fluid, the pressure distribution within the system, the fluid flow rates and the geometry of flow. Due to the numerous variables involved in this type of problem, certain assumptions were imposed in deriving the mathematical model and in establishing the solutions. Two gases, characterized by specific gravities of 0.6 and 0.7, were selected to typify Gulf Coast reservoir fluids. The gas intrustion entered the wellbore as an immiscible &apos;References given at end of paper. JOURNAL OF PETROLEUM TECHNOLOGY

Jan 1, 1969

By Claudio Barsotti, Leonard C. Kitchener

INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950&apos;s the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits INTRODUCTION The major mining operations of the Ontario Division of Inco Metals Company are located in the Sudbury Basin. Around the rim of this geo- logical formation and within thirty miles of the City of Sudbury are located eleven under- ground mines of the Company, two of which are on standby. In addition, there is one mine in Northwestern Ontario at Shebandowan, 1127 Km (700 miles) northwest of Sudbury. In 1980 ore production totalled 10.6 x 10 mt (11.7 million tons) from underground and open pit operations. Underground mining methods include blasthole, vertical retreat, sublevel caving, cut-and-fill and undercut-and-fill. Inco reduction operations in the Sudbury area include two concentrators, one smelter, one iron ore recovery plant, a copper refinery a nickel refinery and a high purity plate rolling mill. As well, an electrolytic nickel refinery is located on Lake Erie at Port Colborne, near Niagara Falls. In the Sudbury District, Inco employees total 14,278 of whom 6,490 are directly employed in the mining and milling operations. I T H DRILLING Background - The use of long blastholes in underground operations at Inco mines in the Sudbury district started more than 30 years ago at the Levack Mine. At that time, diamond drills were used to mine ore by open stoping and for pillar recovery. By the 1950&apos;s the concept had been extended to all mines. The heavy percussion drill was also developed by this time and led to the acceptance of the 11.43 cm (4% in.) piston diameter drifter for bar and arm and fan drill applications. The use however, of the nominal 5.08 cm (2 in.) diameter blastholes drilled radially from the level or sublevel causes overdrilling at the periphery. As well, the smaller holes are subject to hole deviation, are difficult to drill beyond 38.1 m (125 ft.) and require the need for several drilling horizons or sublevels. The need to improve blasthole stoping techniques and our experience with large diameter blastholes in open pit mining led to the trial of an I T H drill in 1962. The test was unsuccessful however, since button bits were not available at the time and the tungsten carbide cross bit experienced short life, gauge loss, and caused hole deviation and poor penetration rates. The successful application of the raise borer beginning in 1964 and the ability to drill 20.32 cm (8 in.) to 27.94 cm (11 in.) diameter pilot holes led to the development of smaller, more portable, rotary drills for blasthole mining. As a result, a mining method based on the use of 20 cm (7 718 in.) diameter, 60.1 m (200 ft.) long rotary blastholes was developed and tested successfully at our C.C.North Mine. Between 1972, when the method was first tested, and 1973 over 4572 m (15000 ft.) of large holes were drilled with rotary drills in the recovery of 175,960 mt (194000 tons) of primary stoping and pillar remnants. A new mining method was developed that made use of this large hole drilling equipment. Instead of longhole carbide drilling by bar-and-arm or fan drill set-ups at sublevels, the large diameter holes were drilled full stope height from the top sill, which substantially reduced development, drilling time and improved fragmentation. These drills however, were difficult to move and set-up, and had a high maintenance cost and low productivity. The capital outlay and extensive technical development required to improve these drills and reduce the high drilling costs however, was economically unattractive. New development in drills and button bits

Jan 1, 1981

By A. F. Giamei, E. J. Freise

A discussion of the various factors affecting the accuracy of volume fraction determination by the direct comparison X-ray diffraction method is presented. To minimize errors introduced by nonrandomization effects such as preferred orientation and large grain size, as well as errors introduced by statistical effects, an iterative mathematical analysis is introduced. This analysis is applied to all observable diffractio~ spectra from a given specimen by means of computer techniques and is statistically superior to the standard direct comparison technique which utilizes only one or tm sets of intensity spectra. The computer program also presents a graphical interpretation of- the results which enables the investigator to visualize and readily assess the scatter in volume fraction estimates caused by deviations from randomness. Finally, the iterative analysis is applied to experimental data collected from a series of plain carbon steels in both the as-received and spheroidized conditions to determine the volume fraction of cemen-tite present in each case. The results show markedly good agreement with chemical analyses for all spheroidized specimens. In theory, quantitative X-ray diffraction is a power-ful analytical technique for precise determination of the volume fractions of various phases present in a multiphase poly crystalline aggregate. There are two generally used methods; both utilize the fact that the intensity of a diffraction line of a particular phase is a function of volume fraction of that phase present in the aggregate. The more common method is the so-called internal standard technique where a known amount of standard substance is mixed with the aggregate containing the unknown. The resulting ratio of the intensity of a particular diffraction line of the unknown to the intensity of a diffraction line from the standard is used to find the weight fraction of unknown material by reference to the intensity data obtained from a previously prepared set of standards containing the same amount of standard material. The details of this technique are outlined in standard works on X-ray diffraction.&apos; The disadvantages of the technique are that it requires the use of powder specimens and that the powder mixture must be homogeneous near the surface to the maximum effective beam depth. The alternative technique is the direct comparison method in which the ratio of the intensity of a diffraction line of a phase in the aggregate to the intensity of a second-phase diffraction line yields the ratio of the volume fractions of each phase present. This method has been applied most extensively to the determination of the percentage of retained austenite in martensitic steels and to determining the amounts of hcp and fcc allotropic modifications in pure cobalt5 and the amounts of hexagonal and rhombohedra1 modifications in graphite.8 This method is applicable to bulk as well as powder aggregates and is the technique which will be considered in the following text. It is the purpose of the present communication to show that by combining the results of X-ray diffrac-tometry with the use of high-speed digital computers the results of the direct comparison quantitative X-ray analysis technique can be optimized by using all of the data available on a diffraction pattern. THEORETICAL DISCUSSION In optimizing any quantitative X-ray diffraction experiment, the problem of accuracy vs time to collect and analyze the experimental data arises. For any method to be practical, it is required that both experimental and analytical procedures are reasonably short. In most of the previous work performed by the direct comparison method, intensity data from only one or two sets of peaks were used to calculate the volume fraction of phases present in the aggregate. Consequently, rather long-time experimental measurements are required to assure that the intensity data are sufficiently accurate to justify the use of one or two sets of data. By using computer techniques to analyze the experimental data it becomes feasible to use all of the available data on a diffraction pattern. By so doing, the time spent in measuring any one diffraction maxima can be appreciably reduced. Although this results in poor counting statistics for any one maxima, the number of data points available for analysis is greatly increased. Based on the above discussion, it will be assumed that a continuous scanning counter-diffractometer technique will be used to collect intensity data from a two-phase mixture. The integrated intensity of the ith diffraction line from the a phase in the aggregate is given by:&apos;" where is the volume fraction of the a phase, The various quantities in Eq. [la] are angular independent while those in [lb] depend on the hkl spectrum of a particular phase. The meaning of the individual quantities in Eqs. [la] and [lb] are given in Appendix 1. It is convenient at this point to outline briefly the factors which will affect the measured intensity of any one hkl spectrum. a) Extinction effects arise from two independent experimental conditions. Primary extinction arises from a high degree of crystal perfection and results in spectra having lower intensity than predicted by Eq. [I]. Any treatment, such as powdering, which reduces

Jan 1, 1968

By H. E. Cline

Mechanical properties of the eutectic between CoAl and cobalt were measured over a range of- temnperatures and strain rates for a variety of microstructures produced by directional solidification and by thermo-mechanical processing. Directional solidification led to rodlike, lamellar, and irregular microstructures. The unusually high volume fraction of the cobalt-rich rods and the lurge spacing of the rods were explained by the phase diagram. The hot-worked structure consisted of fibers of COAL in a cobalt-rich matrix. The roonl- tevlperature strength of the uvrought material increased with decreasing grain size but the 1000°C strength decreased with decreasing pain size. At high temperatures the directionally solidified tnaterial was stronger and less strain-rate-sensitice than the hot-rolled material. The fine-grained hot-worked ma-terial became superplastic at high temperatures, with tensile elongations greater than 850 pct, while at root temperature this material was ductile and impact-resistant because of the ductile matrix. Fracture occurred in the directionally solidified material at elevated temperatures by inter phase separation and at roorn temperature by cracks in the intermetallic phase. Growth of these cracks was impeded by the ductile cobalt-rich phase. It was found that the CoAl intermetallic remains ordered at elevated temperatures. DIRECTIONAL solidification of eutectic alloys has been used to produce structures consisting of parallel rods or lamellae. Although the spacing of the phases depends on the growth rate, it has been observed to be of the order of 1 µ in many eutectics. A strong intermetallic phase has been used to reinforce a ductile matrix in the rod eutectic A1-Al3Ni and the lamellar eutectic Al-Al2cu.1 The microstructure of the eutectics A1-A13Ni and A1-A12Cu remained aligned after samples of these alloys were exposed to temperatures just below their melting points for long times. Stability of the microstructure at elevated temperatures makes directionally solidified eutectics a candidate for high-temperature applications. Recently Thompson4 has developed the Ni-NiMo eutectic containing 40 pct NiMo lamellae, giving a tensile strength superior to nickel-base superalloys. Unfortunately, this eutectic oxidizes rapidly at elevated temperatures. By mechanically processing a two-phase structure, one may reach strengths as high as 700,000 psi, as demonstrated by drawn pearlite.5 In this case the strengthening mechanism was thought to be related to the fine substructure formed during deformation.5 However, a heavily worked structure may recrystallize and coarsen at elevated temperatures. Some worked eutectics such as Al-Al2Cu,6 Pb-Sn,7 and Sn-Bi7 have shown unusually large elongations in tension when tested at elevated temperatures. This phenomenon of large extension, called "superplasticity", was related to the fine grain size of wrought two-phase alloys at elevated temperatures. A mode of deformation of "superplastic" material has been shown to be grain boundary sliding,&apos; which has also been observed during creep of polycrystalline materials.9 The Co-A1 system was chosen for this investigation after examining the phase diagrams of binary eutectics." The high melting point of 1400°C, the aluminum content which was expected to give oxidation resistance, and the properties of the intermetallic CoAl were the chief factors influencing this choice. This eutectic consists of a mixture of the intermetallic CoAl and a cobalt-rich solid solution. The intermetallic CoAl has a large range of solubility and a CsCl structure." From the similarity between CoAl and NiAl one would expect CoAl to be ordered at elevated temperatures; however, specific heat measurements" show a transition at 800°C. West-brookL2 has measured the hot hardness of CoAl and found a rapid decrease in hardness above 600°C. The tensile properties and stress rupture properties of as-cast CoAl-Co eutectic were measured by Ashbrook and wallace13 who report a room-temperature tensile elongation of less than 1 pct. I) EXPERIMENTAL A) Sample Preparation. Experimental materials were prepared by directional solidification, by hot working, and by powder processing. The starting materials were electrolytic 99.9 pct pure cobalt and 99.99 pct pure aluminum. 1) Directional Solidification. A vertical Bridgman apparatus heated by induction was used to directionally solidify cylindrical ingots $ in. in diam and 5 in. long. The apparatus was first evacuated and then an argon atmosphere was introduced to retard evaporation. The ingots were contained in an alumina crucible inside a graphite susceptor that rested on a movable water-cooled base. The base was lowered out of the induction coil at a constant rate. Eight of the ingots were solidified using a drive rate of 2.5 cm per hr, two of the ingots at 1.2 cm per hr, and one ingot at 10 cm per hr. The eutectic composition Co 10 wt pct A1 was used in all but one ingot which had the composition of the stoichiometric CoAl intermetallic, Co 32 wt pct Al. 2) Mechanical Processing. At 1000°C the eutectic Co 10 wt pct A1 is a mixture of an intermetallic phase, Co 21 wt pct Al, and a cobalt-rich phase, Co 5 wt pct Al.10 These phases differ from the stoichiometric CO 32 wt pct A1 and pure cobalt because of the large solubility of this eutectic at elevated temperatures." Four rectangular slab ingots, 4 by 1 by 12 in. high, of Co 10 wt pct Al, Co 5 wt pct Al, Co 21 wt pct Al, and Co 32 wt pct A1 were cast for hot rolling. The cobalt was first vacuum-melted, H2-treated for 20 min,

Jan 1, 1968

By W. O. Philbrook, L. D. Kirkbride

IN the normal operation of the iron blast furnace, reduction of the iron oxides is accomplished almost entirely above the tuyeres.&apos; Blast furnace slags usually contain less than 0.5 pct FeO, although higher values may occur with abnormal operation. There is reason to conjecture, however, that incompletely reduced ore may sometimes reach the hearth and enter the slag as a result of heavy slips or, perhaps, even from cores of excessively large lumps of a charge material of poor reducibility. The possibility of reoxidation of iron droplets falling in front of the tuyeres has been considered by several writers. It would be of interest, to know how rapidly iron oxides reaching the slag for any of these reasons could be reduced by reaction with coke or with the high carbon liquid iron in the hearth. In comparison with the hundreds of papers that have appeared on various aspects of the reduction of solid iron oxides by gases and in the presence of several forms of carbon, little work has been published on the reductioin of liquid oxides or slags. Dancey measured rates of reaction of the pure liquid oxides, both FeO and Fe,O,, with molten iron containing about 4.3 pct C. The oxide was dropped into the cup formed in the upper surface of the iron by rotating the crucible and melt. Under these conditions, reduction of either FeO or Fe,O., was completed in less than 10 sec. The present study was concerned with the reduction of FeO from blast furnace-type slags containing less than 5 pct FeO and melted over carbon-saturated iron in stationary graphite crucibles. The results were considerably different from those found by Dancey, as will be discussed later. Although this work is of interest in relation to hearth reactions in the blast furnace, interpretations must be made with caution because the experimental conditions do not duplicate those within a furnace and may not even lead to the same reaction mechanism. The authors were motivated in undertaking this work by an additional interest—the part played by FeO reduction in the mechanism of de-sulphurization of iron by slags under similar experimental conditions. Derge, Philbrook, and Goldman eveloped detailed experimental evidence to support a three-step mechanism for desulphurization like that originally proposed by Holbrook and Joseph&apos; (These reactions are written in molecular form for convenience, but this is not intended to imply the existence of molecules of FeS in the bulk metal phase nor to deny the likelihood of ionic reactions in the slag.) Earlier work by Chang and Goldman" had shown that the overall reaction follows first-order kinetics with respect to sulphur and that the rate of reaction is proportional to the slag-metal interface area, which observations have been confirmed by subsequent work. Later studiese,&apos; have established the influence of al.loying elements on the first and last steps of the reaction. This paper reports a study of step 3 alone, uncomplicated by the simultaneous process of sulphur transfer. Apparatus and Procedure The experiments were made in a conventional high frequency induction furnace powered by a 35 kva Hg spark gap converter. The graphite crucibles used for most of the runs were 14 cm (5.5 in.) deep and 4.8 cm (1.9 in.) ID with 0.75 cm (0.3 in.) wall. An insulating cover with a small opening for withdrawing samples was used to minimize heat loss and infiltration of air into the furnace. The crucible was charged with 300 g of carbon-saturated iron and either 65 or 100 g of prefused slag analyzing 38.0 pct SiO,, 15.4 pct A10 and 47.1 pct CaO. To obtain the cleanest possible interface at the start of the reaction, the metal and slag were brought to temperature together to prevent the rejection of kish graphite that would have been caused by the chilling effect of a large addition of cold slag to carbon-saturated iron. After temperature control had been established, the desired amount of iron oxide was added in the form of a prefused slag of composition 73.6 pct FeO, 7.7 pct AWX and 19.0 pct SiOl. This slag addition was observed to be molten in somewhat less than 1 min, and a very vigorous reaction proceeded for 1 to 2 min after its introduction. Zero time was taken as 2 min after the ferrous silicate slag addition. Slag samples weighing about 0.5 g each were taken periodically by a copper chill sampler." The weight of the initial slag was large relative to the weight of samples removed, so that the slag weight never varied by more than 5 pct during any run. Temperature was measured by a calibrated W/Mo thermocouple immersed in the metal, with a graphite tip cemented over the fused silica protection tube to prevent attack by slag and metal. After some difficulties with uncertain temperatures during the first two runs, the practice adopted to position the thermocouple for reproducible results was to lower the protection tube to touch the bottom of the crucible and then raise it 0.5 cm. The apparent temperature gradient between the bottom of the crucible and the top of the slag was found to be 15°C (27°F). but much of this spread was probably the result of inadequate immersion of the protection tube to off-set conduction losses along the graphite tip when the thermocouple was inserted only into the slag. The temperature of the bath was controlled within 25°C (9°F) during a run.

Jan 1, 1957

By GEORGE H. DERN

IF THE engineer is to go into politics, as I think he should, I believe the curriculum of every engineering school should be amended to include a good stiff course in public speaking. My observation has been that the engineer in private conversation can scintillate as brightly as a life insurance agent or an oil stock salesman, but before an audience, with rare exceptions, he is a total loss. He will not get up and talk. He hides his light under a bushel, and sits on the bushel as dumb as an oyster. I have seen meetings of the Utah Section at which some topic of general interest to the members was up for discussion, and where an animated debate was the logical thing to expect. After the chairman states the subject and invites discussion, there is dense silence. Finally a member, bolder than the rest, gets up and with trembling voice and knees makes a motion. The motion carries, the meeting adjourns, and then the members gather into groups and begin to discuss the question seriously -and intelligently, giving cogent arguments on either side and embellishing their remarks with appropriate or inappropriate epithets illustrations and figures of speech. Now, I am not pleading for more speechmaking. The good Lord knows we have too much of this great American indoor sport already. But I think every man ought to be able and ready to express his opinions at the proper time. Some men have a reputation for wisdom because they do not talk much. We speak of the wise old owl because she never speaks, but in my opinion the owl&apos;s reputation for wisdom is vastly overrated. silence is more apt to be a cloak for stupidity than for wisdom. The person who has ideas can- not exert any influence by keeping them locked up in his own mind. The great motive force of the world is not muscle, but ideas, and ideas in order to get in their work must be released.

Jan 1, 1925

By J. M. GARZA

The production of oil in Mexico during 1945 was 43,402,852 bbl., or a daily average of 118,912 bbl. In March 1938 most of the oil properties were taken over by the Mexican Government and since then have been operated by Petroleos Mexicanos, an agency of the Government. The variations in the production during the last 8 years have been due to- fluctuations in the export market demand for Mexican oil rather than to the productive capacity of the fields. Since 1937, yearly production, to the nearest hundred thousand barrels, has been as follows :

Jan 1, 1946

By D. O. LIVINGTON

(Presented by invitation at a meeting of the Spokane Local Section of the institute, Feb. 17, 1912.) THE Pilares de Nacozari mine is located in Sonora, 75 miles south of Douglas, Ariz. The town of Douglas is on the International Boundary and is the place at which the ores from the Bisbee mines are smelted. The Moctezuma Copper Co. owns the mines at Nacozari, and the copper-concentrates shipped to the Copper Queen smelter, at Douglas, make a good smelting-mixture with the Bisbee ores. The Moctezuma Copper Co. and the Copper Queen smelter at Douglas, as well as the railroad from Douglas to Nacozari, are owned by the Phelps Dodge Co. The ore-deposit occurs in the form of a large ellipse with a major axis of approximately 2,000 ft. and a minor axis of about 600 ft., the major axis bearing about 90 W. of N. The whole of this ellipse is more or less mineralized; the surface being principally an iron gossan with some occasional copper-stains. Below the oxidized zone, which is not more than 50 ft. deep, the minerals are pyrite and chalcopyrite, with occasional seams of chalcocite, the latter being rare. There appears to be no well-marked zone of secondary enrichment, the oxidized gossan over the greater part of the deposit changing suddenly to what is apparently the original unaltered ore. The copper-values are concentrated around the perimeter of the ellipse, and it is principally around this perimeter that the mining is done. The ore mined averages a little more than 3 per cent. of copper, with a small amount of silver, less than an ounce per ton. Some ore of considerably higher grade than this has been shipped, however, but the above average is of the mill-run. The ore is wider near the two ends of the ellipse than along the sides, and is mined in some cases to a width exceeding 200 ft. The country-rock for the first vertical 500 ft is a volcanic acid breccia, probably rhyolitic; below

Sep 1, 1912

By AIME AIME

The following changes of address of members have been received at the Secretary&apos;s office during the period of March 15 to May 1, 1907. This list, together with the list of changes of address published in Bi-Monthly Bulletin, No. 14, March, 1907, supplements the annual list of members corrected to Jan. 1, 1907, and brings it up to the date of May 1, 1907. The names of members who have accepted election during March and April, 1907 (new members), are printed in italics. The large number of changes of address since Jan. 1, 1907; shows the importance of publishing these changes as frequently as possible, and the Bi-Monthly Bulletin has. been selected as the means to present this information to the members of the Institute. By the simple method of cutting out these names and addresses and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date, and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages.

May 1, 1907

Jan 1, 1924