Search Documents

By F. Morgan, M. Muskat, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By Lester L. Hirst, Arno C. Fieldner, Henry H. Storch

EXPERIMENTAL work on liquefaction of coal was taken up by the Bureau of Mines in 1936 when it became evident that a prudent policy from the national point of view should include preparation for the time when gradual exhaustion of petroleum resources would require supplementing the growing demand for motor fuel with gasoline and diesel oil from coal. At that time (1936) certain foreign nations that had no home sources of petroleum, especially Germany, England, and Japan, were conducting active research and at least two of them were producing liquid fuel from coal on a commercial scale. Germany was reported to have an annual producing capacity of 800,000 metric tons of gasoline per year, and England had just put into operation the Billingham plant of Imperial Chemical Industries for the hydrogenation of bituminous coal and tar by the Bergius-.I.G. process. The annual capacity of this plant was about 150,000 long tons of gasoline per annum (3500 bbl. per day). With these developments taking place in foreign countries, it seemed important to undertake a long-range program of fundamental research in this country to establish a sound groundwork for the evaluation of foreign work on synthetic liquid fuels and at the same time to obtain data on the oil yields and operating difficulties using various kinds of American coals and lignite to the hydrogenation process. The results of such research would be useful in determining the yields and quality of liquid products obtainable from various coals so that American industry would be in position to select the most suitable coals and make rapid progress in establishing this new industry when the commercial need should arise. It was hoped, also, that progress in a better understanding of the chemistry of coal hydrogenation would reduce the cost of the process materially. To carry out this program, a small continuous unit capable of hydrogenating 100 lb. of coal in 24 hr. was installed at the Central Experiment Station of the Bureau of Mines at Pittsburgh, Pa. Small steel autoclaves or bombs of 0.3 gal. (1.2 liters) capacity also were used for batch-hydrogenation experiments in the study of the chemical fundamentals of the process. Much valuable assistance was obtained in planning the experimental program and designing the equipment from the Fuel Research Station of Great Britain and the Fuel Laboratories of the Mines Department of Canada, where such investigations had been in progress for several years. EQUIPMENT AND GENERAL PROCEDURE OF RESEARCH The industrial liquefaction of coal by the Bergius-I.G. hydrogenation process as practiced at Billingham, England, from

Jan 1, 1944

By G. D. Boozer, W. H. Somerton

RESEARCH CORP., LA HABRA, CALIF. Thermal diffusivities of some typical sedimentary rocks have been measured by a rapid unsteady-state technique. Thermal data including diffusivity and conductivity are presented for the temperature range of 200" to 1,800°F. Diffusivities calculated from steady-state conductivity rneasurernents compared favorably with unsteady-state data at the lower temperatures. Unsteady-state data are less reliable at higher temperatures; reported values may be as much as 20 per cent high at temperatures in excess of 1,500°F. This is caused partly by the simplified method used in calculating diffusivity from experimental data and partly by the many thermal reactions which occur at the higher temperatures. The marked decrease in thermal diffusivity and conductivity at elevated temperatures indicates the importance of considering the temperature dependence of thermal properties in subsurface heat-transfer calculntions. Knowledge of the effects of liquid saturation, overburden and pore pressures, and heats of reaction of reservoir materials will be required before complete subsurface thermal analyses may be made. INTRODUCTION Heat-transfer calculations are becoming increasingly important in the analysis of in situ combustion and underground nuclear explosions. Thermal data for natural rock materials at elevated temperatures are generally unavailable. Calculations at high temperatures may be grossly inaccurate if temperature-dependent thermal properties of rocks are not considered. It is known that the heat capacities of rocks increase with temperature. Heat capacities may be calculated from chemical or mineralogica1 analyses of the rock system. Thermal bulk expansion of rocks is believed to be small, although few data are available. Thermal conductivities of most natural rock materials decrease with increased temperature. Thermal diffusivity, defined as the thermal conductivity divided by the product of the heat capacity and the bulk density of the material, is used in unsteadv-state heat-transfer calculations. It is apparent that thermal diffusivity decreases markedly with increased temperature. A new method, which gives a nearly continuous record of thermal diffusivity within the temperature range of 200° to 1,800°F and requires less than 1.5 hours for the run,' was used to measure the diffusivity of several sedimentary rocks. Thermal conductivities were calculated from measured bulk densities, heat capacities calculated from chemical analysis and the measured diffusivity values. Thermal conductivities were measured at lower temperatures by a steady-state technique1 to test the agreement of data obtained by the two methods.

By Carl H. Samans, Charles R. Austin

In an earlier serics of studies on 18-8 stainless steel at 600º, 700º, and 800ºC.l one pretreatment was used throughout; viz., 15 min. in hydrogen at 950°C., followed by an air quench. Several manufacturers of this alloy since have expressed doubt as to the suitability of the temperature employed, recommending instead the more customary Strauss treatment as promising superior results. In this subsequent investigation on the effects of the temperature of pretreatment several interesting points have arisen, which are described in this paper. Previous work on our equipment had shown a marked difference between alloys of "similar chemical composition" that had been manufactured by different companies. Accordingly, one mill-bar length was selected from which to prepare all specimens. It could then be assumed that any marked differences in creep characteristics would be due to effects resulting from variations in the pretreatment of the alloy. The material was furnished by the Allegheny-Ludlum Steel Co. in the form of 5/16-in. dia. rod, finished by air cooling from a mill anneal at 1950°F. (1066°C.). It was analyzed only for the elements shown: carbon, 0.07 per cent; chromium, 18.73; nickel, 9.46; manganese, 0.40. Three pretreating temperatures were chosen, the specimens being held for 15 min. in hydrogen at either: (1) 1150°C., to conform to the recommended Strauss treatment; (2) 950°C., to compare with the results of previous tests; or (3) 75Q°C., to initiate precipitation of carbides in the material before testing. As the test cross sections were only 1/8-in. dia., air cooling followed the annealing treatment. These treatments permitted two direct comparisons: (1) between the 1150" and 950°C. treatments to indicate the effect of grain size when all carbides were probably in solution at the start of the test; and (2) between the 950" and 750°C. treatments to indicate the effect of carbide "nucleation" for similar grain sizes.

Jan 1, 1940

By Richard L. Gordon

THE PROBLEMS AND POSSIBLE SOLUTIONS Toward the end of the 19th century, American industry began a drastic reorganization. The many, small, often-regional firms were supplanted by large national corporations-often produced by mergers among the existing firms. Giant companies appeared throughout American industry and many of them were engaged in the mineral industries.a The largest combines, by far, to emerge during the period were United States Steel and Standard Oil. Long before the restructuring had run its course, widespread concern arose over the process of concentration. Efforts were made to control, if not stop, the transformation. The concern produced the Sherman Antitrust Act of 1890 and the first of many federal regulatory agencies-the Interstate Commerce Commission (see Refs. 24, 31, 42). The basic objectives of these policies remain unclear to this day. The crucial issue is whether the goal is primarily to insure development of a more competitive economy or to preserve a social structure leaving more scope for small businesses. Complications arise from difficulties in agreeing upon the meaning of these terms. Studies of the early years of the antitrust movement suggest that it involved no particular concern over the mineral industries. Objections were directed at big companies in general. To be sure, the conservation movement arose in roughly the same period and did stress the evils of monopoly control of minerals. However, direct, continuing influence of conservation policy on antitrust is not apparent. Many of the most important antitrust cases, nevertheless, involved minerals. This, of course, may be sheer coincidence; the choice of cases has never followed any obvious pattern. Certainly, no simple hypothesis can explain the interest consistently. Once it may have been true that mineral industries were more likely than other sectors to be dominated by a few large companies. Yet, often sharp reversals of such tendencies -e.g., in oil and aluminum-have not removed antitrust interest. The importance of minerals to the economy cannot satisfactorily rationalize antitrust interest. The equally

Jan 1, 1976

By George S. Rice

A problem of possible subsidence of the surface from mining operations, which might have had disastrous results, arose in 1913 at the Brier Hill mine, of the Penn Iron Mining Co., near Norway, Mich., now managed by Pickands, Mather & Co. for the Bethlehem Steel Co. A double track and sidings of the Chicago & North Western Railroad passed over part of the mine, and if subsidence had reached the surface it might have affected the stability of the tracks. The chief purpose of this paper is to record the facts disclosed by investigations of underground movement from 1913 to 1919, when the tracks were moved, and subsequently at intervals, as engineering data of value from mining carried on below the tracks in the steeply pitching lenses. A secondary purpose of this paper is to describe a novel method for determining the rate of speed of upward breaking above the mine excavations. This method was found effective and might be used elsewhere under similar conditions. The mine workings under consideration were developed from the Brier Hill shaft, which was circular, concrete-lined, 14 ft. in diameter and about 900 ft. deep. They extended about 800 ft. westward from the shaft, and nearly parallel to a corresponding length of the railroad tracks. The highest part of these workings was at a depth of 400 ft. below the tracks (Figs. 1 to 12). The mining company had the right to remove the ore, the railroad assuming that the surface would be supported. Finally, without legal controversy, an amicable adjustment was reached as to what should be done to lessen or obviate the hazard of subsidence. Method oF Mining Before the problem became acute, the mining company, to decrease the possibility of subsidence, had been mining the part of the orebody that lay under the tracks by a room-and-pillar system, back-filling with

Jan 1, 1934

By J. E. Smith, P. B. Crawford, B. L. Laudrum

A method is presented by which the displacement efficiency of a steam-injection process may be determined. The method consists of a determination of the position of the steam front at a particular time and the application of the Buckley-Leverett theory to the hot and cold regions of the reservoir with the appropriate hot or cold fluid properties. A uniform, linear flow system is assumed for this study. The method is applied to a number of reservoir conditions. The primary properties which affect the results of a steam-injection process are the oil viscosities at steam and reservoir temperatures, injection rate, pay thickness and oil saturation. The efficiency of steam injection is compared with that of water injection for a 10-acre, linearly flooded reservoir. In reservoirs where the oil viscosity is about 35 times the water viscosity, the steam process yields recoveries about 20 per cent higher than the water flood. Where the oil viscosity is near 500 cp, the steam process may recover from three to four times as much oil as a water flood. INTRODUCTION In a previous paper,' a method was suggested for evaluating a steam-injection process. Emphasis was placed upon the determination of the steam-front position in the reservoir at various times. In the present paper, the displacement process is studied in more detail. The approach is essentially that employed by Jordan, Rayne and Marshall3 in their study of hot-water injection. The steam-injection process is quite complex, and an exact description of the process has not been found; however, a qualitative description can be made. When a quantity of steam is injected into a relatively cold reservoir, the leading edge of the steam front continaally flows into cool sand, and some steam condenses. As more and more steam condenses, a bank of condensed water will form which is augmented by displaced connate water. The reservoir may be divided in three regions—(1) a region containing displaced fluids at reservoir temperatures, (2) a region contain- ing water at reservoir temperature and (3) a region occupied by steam. The reasons for the lack of a region of hot water or oil of any appreciable size have been discussed.' A method has been presented by which the location of the steam front can be determined even when heat losses to the regions surrounding the reservoir are sizable compared with the amount of heat injected. It remains to show the effectiveness of steam injection in increasing the ultimate oil recovery. To illustrate the technique for determining the increase in displacement efficiency and, hence, the increase in ultimate production, two sets of hypothetical reservoir conditions will be studied in detail.

IN the preceding chapter on thermochemistry and the reactions in and between metal and slag phases and in the following chapter on fuel combustion the main emphasis is placed on the equilibrium or "static" conditions. This equilibrium viewpoint is not concerned with the rate of change in the process or with the mechanisms or paths followed between initial and final states. The questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling its operation, and also in understanding its limitations. Any treatment of kinetic factors in the open hearth such as is attempted here and in Chapter 22 must at present be largely qualitative and incomplete. We are only beginning to get quantitative data on rates of reaction and diffusion at high temperatures, as indicated in Chapter 15. Empirical data in the literature on furnace operating rates do not help much to illuminate the details of gas-flow patterns and the complexities of heat flow in the many parts of the furnace system. This chapter is intended to give the reader an introduction to the problems of the flow of gases through the furnace system and the flow of heat in this system. An adequate discussion would require several times the space available here; it is possible here only to outline a few fundamentals and to indicate some of the conditions of heat and gas flow peculiar to the open hearth. Several good general treatments of these subjects may be found in the literature (see references at the end of the chapter). For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance. They are also important to the operation of the process, at least to the extent of a general qualitative picture of the movement of gases in the system. MOTION OF GASES IN FURNACE DUCTS Fluid flow in general can vary between the extremes of laminar or streamline flow with a minimum energy loss, to irregular

Jan 1, 1951

IN the decade beginning 1850, the development by William Kelly in I the U.S.A. and Henry Bessemer in England of the pneumatic method of refining pig iron, known as the Bessemer process, gave the world the first method of producing low-cost steel in large volumes. Briefly, the Bessemer process consists of blowing air through liquid blast furnace iron in a refractory-lined vessel known as a converter. The air enters the iron in the furnace bottom through tuyeres, and during its passage through the iron removes the carbon, manganese, and silicon by oxidation. The heat produced by oxidation is sufficient to raise the temperature of the liquid metal to normal steel casting temperatures and, in addition, to melt some scrap. In the 1860's, the open hearth process was introduced which in the early part of the twentieth century surpassed the Bessemer process in steel production. In the early 1870's, Thomas and Gilchrist discovered that phosphorus could also be removed if lime were added and the converter lined with basic refractory; the modification is known as the basic Bessemer process and is used in Europe. Bessemer steel usually contains between 0.010 and 0.020 per cent nitrogen and between 0.05 and 0.10 per cent phosphorus which influences the properties. Henry Bessemer,1 in 1856, recognized the possibility of using oxygen in the converter process, but the cost was prohibitive. This interest was associated with the theoretical balance of the Bessemer process. Experimental work' has indicated that bottom blowing with pure oxygen results in serious converter bottom and tuyere erosion. Dilution of the oxygen by steam has been observed to be an effective means of maintaining low-nitrogen content of the steel and at the same time reducing bottom and tuyere erosion. A further advantage is that the fume emission characteristic of Bessmer operation is reduced. The addition of steam to the oxygen, however, reduces scrap-melting capacity due to the endothermic reaction characteristics of steam. The possible advantages of refining methods for steel using high-purity oxygen have been recognized for over a hundred years, but the develop-

Jan 1, 1964

By Clarence E. Sims, Donald W. Williams, George A. Moore

INTRODUCTION DURING the past several years, the steel casting industry has made studies of heavy castings in which the test bar has been taken from heavy sections rather than from attached or separately cast coupons. It has been noted that the ductility properties of these heavy sections are often lower than those normally expected. Such lowered ductility is usually accompanied by a spotty test bar fracture, and the ductility values can often be greatly improved if a low-temperature aging treatment is given to the casting. A loss of ductility of this type is considered "abnormal," since it is not accompanied by an increase of tensile strength or hardness, and "temporary" when the ductility can be restored by aging. The cure of such an abnormal condition represents a real improvement in the quality of the steel, Several types of abnormal loss of ductility can be distinguished, of which those caused by excessive amounts of inclusions of undesirable type and those caused by unsuitable grain size and ingot structure are well known. The particular type of abnormal lowered ductility currently under consideration may be distinguished by the fact that the low-temperature aging treatment necessary for its relief is insufficient to cause any visible change in the microstructure as ordinarily observed. As this aging will in fact eventually occur at room temperature, the phenomenon of present interest may be given the symptomatic definition, "Temporary Abnormal Low Ductility." Some hundreds of previous investigations, largely qualitative in nature, have established, beyond reasonable doubt, that hydrogen is normally present in newly manufactured steel and that this gas, in small amounts, can cause a temporary abnormal loss of ductility. The commonly observed association of high gas content and low ductility has given strong evidence for the presumption that hydrogen-, possibly assisted by other gases, is the primary cause of the low ductility observed. Accordingly, The Steel Founders' Society of America has, since Nov. 1, 1944, sponsored investigations at Battelle Memorial Institute whose primary objective is to obtain quantitative information on the relation of the amount of hydrogen and nitrogen in steel, together with associated methods of steelmaking and treatment, to low-ductility effects and porosity. The interest of this investigation thus extends to permanent abnormal losses of ductility, such as are caused by the inclusions which sometimes result from special deoxidizing practices and possibly from metallic nitrides, but as these can be distinguished from the temporary effect of hydrogen, they have been excluded from the work reported here except when they

Jan 1, 1948

By Neil H. Bostick

A specialized electronic data system processes data taken from normal gologic maps and stratigraphic tables to yield predictions of uranium resource location for an area such as much of the United States. Strata underlying specific quadrangle cells of the earth are evaluated for uranium favorability on the basis of selected criteria of lithology, structure, and stratigraphy but not specific past production in the area. Stored data are computer processed to yield volume of likely host rock beneath each cell to a given depth and at a given favorobility level. Results are plotted by machine directly as maps. A specialized and simplified procedure for predicting approximate uranium resources has been devised at Stanford Research Institute (SRI). The prediction is based on general geology beneath specific area cells of the earth in order to provide complete volume coverage; the strata underlying these areas are evaluated for uranium mineral favorability on the basis of a few selected geologic criteria in order to allow rapid data input. In order that the predictions be generally applicable, they are based on geological factors only, not past ore production of a given cell. Since the bulk of U.S. resources are in elastic host rocks, only such strata are considered in this work. This paper describes the structure and some details of the resource system and how it was tested in an area of the western United States.

Jan 1, 1971

By Henry M. Howe

The brilliant and very original matter in Professor Jeffries' discussion† should rank not only as an independent paper, but as a most important one. In particular, the explanation which it gives of the remarkable Sauveur phenomenon, over which so many of us have puzzled long and hard, is so clear, complete, and cogent as to go far toward establishing Professor Jeffries' hypothesis. The very leatures of Professor Sauveur's photographs which fit this hypothesis so exactly are reproduced in Chap-pell's photographs of steel coarsened under somewhat different conditions.' The ideas developed by these discoveries are so novel that convenicnce of language seems to call for new conventional terms for expressing them. In what follows here I propose certain terms for this end, for criticism and improvement, and I attempt to generalize from Professor Jeffries' hypotheses. Generally speaking, a given set of grains which undergo no growth in the cold will, when the temperature is raised progrcssively, start to grow on reaching a certain temperature, and will continue growing at all higher temperatures. The "germinative" temperature is that at which growth begins, quite as the conditions which cause a seed to grow are "germinative." We have then an inert temperature range below the germinative temperature, and a growth range above it, the germinative temperature being the limit between these two ranges. So, too, a germinant grain is one which is at its germinative temperature, and hence beginning to grow, while inert grains are those below their own germinative temperature, and the term "growing grains" includes those which are germinant and those which are above their germinative temperature. These last could be called " supergerminant" if the distinction should be needed. "Germinative temperature" seems better than "critical temperature

Jan 1, 1917

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well's drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well's limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well's cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well's drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By Enid C. Plante, K. L. Sutherland

PRACTICAL metallurgists are unanimous in stating that oxidation of mined sulphide ore adversely affects separation of the constituent minerals under standard conditions in a mill. Frequently, the need for different operating conditions in different plants is attributed either to the extent of oxidation of the mineral surfaces or to soluble oxidation products. The investigations reported in this paper study the effect of oxidation on the primary condition necessary for flotation, namely that of adhesion of an air bubble to the mineral. OXIDATION PRODUCTS FROM SULPHIDE MINERALS Weinig and Carpenter1 state that the relative rates of oxidation of some sulphides are: FeAsS > FeS2 > CuFeS2 > ZnS >PbS > Cu2S tetrahedrite. They also show that oxidation is rapid at first, that sulphides of older geological formations are more stable than those of recent date and that mixtures oxidize more rapidly than any one mineral alone. The more rapid oxidation of mixtures is borne out by results of Gottschalk and Buehler2 who found that PbS, ZnS and CuS oxidized 8 to 20 times faster when pyrite was present. Only the end products of oxidation, sulphate and the metal ion, were identified in these tests. Gaudin3 states that pyrite is difficult to oxidize in the laboratory. Winchell,4 using pyrite containing 99.98 pct FeS2, allowed water to percolate through a bed of this ground material. At the end of three months only a trace of Fe +++and S04- were found. Even after 10 months the quantity of Fe+++ was only 7.8 mg and S04- 25.5 mg per liter of percolating solution. Carmichael5 confirmed Winchell's results on the slow oxidation of pyrite. Usually the oxidation of sulphide surfaces has been conducted in neutral or acid solutions, the acidity being caused by the oxidation products. Eliseev and Nagirnyak6 found that treatment of pure pyrite with lime gave only thiosulphate, but considered it possible that thiosulphate was obtained not by oxidation of the pyrite itself, but by oxidation of calcium disulphide. Mitrofanov7 suggested that thiosulphate was formed by the following process: oxidation of sulphide to give free sulphur (this frequently happens with marcasite), followed by oxidation of the sulphur to sulphur dioxide and reaction of the sulphur dioxide with sulphur to give thiosulphate. Ferric and ferrous hydroxides, or similar compounds, were shown to be present. The Research Staff of the United Verde Copper Co.8 treated ore from the United Verde mine with lime. Thiosulphate, sulphide and polysulphides were stated to be

Jan 1, 1947

Jan 1, 1969

By C. H. G. Bushell, James E. Lawver, William Barbarowicz

Proper use of automatic controls in the process industries is a combination of art and science. Although many phases of automatic control theory can be expressed by precise mathematical relationships, the final control arrangement usually requires considerable effort by trial and error before the optimum control circuit is found. The failure of flotation operators to recognize that control circuits require study and plant experimentation before satisfactory operation occurs has led to a popular misconception that flotation plants simply do not lend themselves to automation. This widespread belief has been overcome to some degree in recent years by the numerous installations of automatic controls that have paid their way by increasing profits in terms of increased recoveries, lowered costs, or higher grade concentrates. WHY CONTROL ? Any form of automation must be justified in terms of ultimate return on in- vestment by improving quality, by increasing plant throughput, or by reducing the total operating costs. Generally speaking, automatic controls rarely re- place a mill operator. They assist the operator in holding important variables within predetermined limits. Large tonnage operations usually can justify a great deal of automation because an increase in one or two units of recovery results in enormous savings compared to the capital and operating costs of controls. DETERMINATION OF CONTROL The first questions in considering plant automation are: 1) What variables must be controlled? 2) What are the optimum levels of the variables? The optimum operating conditions for any process are those which maximize profits. Many of the variables active in flotation processing can be determined by experimentation in the laboratory or pilot plant 10. Although laboratory experiments can pinpoint variables, the true optimum conditions existing at plant level usually must be determined by plant scale experiments. In recent years, the concepts of detailed experimental designs in the laboratory, followed by plant experiments, have reached the stage of maturity where

Jan 1, 1962

By C. M. Heath, B. W. Gonser

Soft solders are used principally in the automotive, can-making, building construction and electrical industries, but their field of usefulness extends well beyond these principal users to a vast list of miscellaneous applications where metal joints are required. The most common soft solders and the only ones considered in this discussion are those composed of lead and tin, with or without various relatively small percentages of impurities or additions. A small amount of antimony is often purposely added. As an indication of the importance of these lead-tin solders, 8620 long tons of tin were consumed in 1934 in the United States for making new solder, and during most of 1935 from 900 to 1000 long tons often were used each month. In addition, many thousands of tons of secondary solder are recirculated annually. A great many factors influence the properties of joints made with soft solders. Fluxes and the fluxing procedure used to prepare the surfaces to be joined in order to give a true metal-to-metal contact are among the most important of these factors. The temperatures used, cleanliness of the work and general soldering technique have their effect, but when results are unsatisfactory they are usually attributed to the metallic solder itself and the raw materials from which it is made. Sometimes criticism of the solder is justified. The wrong composition may be chosen for a given job, impurities may be present that ruin certain desired qualities, or uniformity may be lacking. A solder may even be looked upon with suspicion because of its ancestry, regardless of its true composition and behavior. To clarify the effect of slight differences in composition as found in commercially refined solders, a comparison of properties of solders grouped according to their origin has been undertaken. This investigation seeks to give practical information on the properties of tin-lead solders produced from virgin metals, from commercially refined secondary solder, and from an electrolytically refined crude

Jan 1, 1936

By M. Muskat, F. Morgan, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By H. S. Jerabek, Charles S. Barrett, Robert F. Mehl

The precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstatten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe3P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. Precipitation of Fe4N from Alpha Solid Solution of N in Alpha Fe Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kauppl and by Lehrerz have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591' C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934