Search Documents

By H. S. Thomsen, W. C. Duesterhoeft, R. E. Hartline

The attenuation and phase shift which formations produce in the electromagnetic field of an induction-type electrical well-logging instrument are great enough to substantially affect the response of the tool to formation conductivity under normal logging conditions. The application of the general equations for the propagation of an electromagnetic field in a conductive medium to the transmitter-receiver coil pair of an induction-logging-tool coil system gives an expression for the response which properly takes the propagation effects into account. A comparison of a calculation of this type with the response computed from the commonly used geometric factor concept, which does not include the propagation effect, leads to a factor Go representing the ratio of the responses computed by the two methods. The value of Go decreases not only with increasing formation conductivity, but also with increasing transmitter-to-detector coil spacing. For a single coil pair with a 40-in. spacing, the value of Go is 0.972 in a 20-millimho/m formation. The value is reduced to 0.915 and 0.812 for conductivities of 200 and 1,000 millimhos/m. As a result, the basic signal generated by the induction-logging coil system is not linearly related to formation conductivity as expected from the geometric factor concept. A uniform conductivity scale can be obtained only by adding a suitable nonlinear element to the recording system. The addition of auxiliary coils, having spacings less than the main-coil span, to achieve focusing results in an even greater departure of the basic signal from linearity with conductivity. The solution of the field equations near the interface between two formations of different conductivity gives the curve shape on an induction logging tool in crossing the interface. The addition of auxiliary coils to achieve focusing can add anomalous character to the curve shape in crossing the interface, which might be mistaken for lithological detail. Preliminary calculations which include the propagation effects in the determination of the conductivity correction for thin beds lead to correction factors which are substantially smaller than those obtained from geometric factor considerations. It is apparent that thin-bed corrections derived from geometric factor calculations are of doubtful validity. INTRODUCTION Although the electromagnetic induction type of electrical well log has been used for a number of years and has gained general acceptance in quantitative well-log interpretation, no technically complete investigation of the mechanism and of its operation has been published. The studies which have been presented are based upon the premise that neither the shape nor the intensity of the induction field of the logging tool is in any way affected by the electrical characteristics of the formation. From the inception of induction logging it has been recognized that under some formation conditions the performance of the instrument could be expected to be substantially different from that predicted by the simplified analysis. This anomalous performance has been called "skin effect" since it is the result of the same phenomenon which causes high-frequency alternating currents to flow only near the surface of metallic conductors. In the range of conductivities encountered in the sediments, the formation actually does not exhibit the sharply defined conducting "skin" shown by metals. The gradual modification of the distribution of the currents in the formation, produced by the induction field of the logging tool, is the direct result of phenomena associated with the propagation of the electromagnetic field through the formation. Therefore, it can be much more appropriately described as the "propagation effect". One purpose of this paper is to review the results of a solution of the equations for the performance of a single transmitter-receiver coil pair induction-logging system which takes into account the propagation effect, showing the manner in which the tool performance established by this analysis differs from that derived from the less comprehensive analyses currently in use. PRINCIPLE OF OPERATION OF THE INDUCTION LOGGING INSTRUMENT The high-frequency alternating current which is maintained at a constant value in the transmitter coil

By A. A. Bauer, M. S. Farkas, F. A. Rough

An investigation of the d-phase relationships between the uranium-zirconium and uranium-molybdenum systems was conducted. A ternary cut joining U-31.5 at. pct Mo to U-74 at. pct Zr is presented on the basis of differential thermal analysis, metallographic and X-ray diffraction data. HyDothetical isothermal ternary sections, inferred from the determined d-phase relationships, are presented for the uraniztm-zirconium-molybdenum system. A ternary eutectoid, at 454ºC, was found in zirconium-rich alloys. Its composition, based on metallography and electron-beam micro-analysis, is estimated as U-61.7 at. pct Zr-7.1 at. pct Mo. URANIUM binary systems have been studied extensively in the past to supply basic information needed in reactor-fuel development. Alloys of uranium with zirconium, molybdenum, and titanium are of particular interest because, in these binaries, extensive or complete solid solubility between the body-centered-cubic forms of these elements and y uranium exists. In addition, an intermediate phase of limited solid solubility forms in each of these systems by transformation of the high-temperature ?-uranium phase. Previous investigation of the phase relationships existing between the intermediate 6 phases in the uranium-zirconium-titanium and the uranium-molyb- denum-titanium ternaries have already been reported.1,2 The results of an investigation of the phase relationships existing between the 6 phases in the uranium-zirconium-molybdenum system is reported here. The phase equilibria that occur in the solid-state portions of the pertinent binary systems are shown in Fig. 1. Phase nomenclature appearing throughout the report is as shown in these diagrams. The crystal structure of the phases in this system are given in Table I. EXPERIMENTAL PROCEDURES Alloys were cast and fabricated to 1/4-in.-diam rod. Specimens were heat treated and examined by metallographic and X-ray techniques. Thermal-analysis data were obtained.

Jan 1, 1960

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By David W. Kennedy, Stephen P. Harrison

In the past few years, a new system has been developed for ventilating longwall panels in some gassy coal mines in the Northern West Virginia area. This system utilizes a five or six foot diameter air shaft to ventilate a group of three or more longwall panels dependent on conditions. This shaft exhausts all the air needed to, ventilate the active longwall and adjacent gob areas. By law, this bleeder fan can handle double the maximum methane concentration allowed in a normal return air course. As a result, the methane that must be diluted by the primary ventilation circuits is reduced. This new ventilation system was first conceived by mine management as a means of coping with a sudden shift in production mode that occurred a few years ago. Formerly, production often consisted of room and pillar mining with continuous miners. The high methane liberation rate was handled by driving entries around a large block of coal prior to mining. This isolated the future mining area from the adjacent coal seam and allowed a major portion of the trapped in situ methane to bleed off. Also, these bleeders served to exhaust return air from the mining area. Once the bleeders were established, productive mining could start. When the decision was made to shift production mode from continuous miners to longwall mining, some of the bleeders did not encompass large enough unmined areas under the old ventilation system to initiate longwall production. Also, many other established continuous miner section bleeders were either improperly positioned or too restricted for longwall ventilation. Unfortunately, standard bleeder development can take up to two years' time. In order to eliminate the old style bleeder system and maintain or increase the margin of safety for ventilation, the bleeder shaft system was conceived. With this system, the only entries developed are those necessary for the longwall, significantly reducing the production delay. In this area, the Pittsburgh #8 coal seam dips to the northwest. As a result of this dip, the bleeder shaft is constructed in the northernmost set of tailgate entries. In this manner, groundwater accumulations can be pumped to the surface and bleeder entries kept dry. During the initial longwall entry development, the bleeder fan can be used to ventilate entries adjacent to virgin coal where significant methane liberation often occurs. Once longwall production starts, the bleeder shaft exhausts the entire air quantity necessary to safely ventilate the longwall. As the bleeder entries deteriorate, the air quantity and pressure characteristics must be increased. The extreme flexibility of the centrifugal fan used at the surface allows the air quantity and pressure to be adjusted without stopping the fan. This improves safety by decreasing the possibility of a methane buildup resulting from the fan being out of service. The bleeder shaft system of ventilation, developed by mine management in Northern West Virginia, can provide a safe means for effectively ventilating longwall panels in excessively gassy mines. This system should be considered where mining conditions are comparable.

Jan 1, 1982

By K. G. Wikle, W. W. Beaver

A general survey of the mechanical properties of commercially pure beryllium fabricated from powder by vacuum hot pressing and other consolidation methods is presented. The effect of fabrication method, grain size, strain rate, and directionality upon both room and elevated temperature tensile properties is reported. BERYLLIUM metal, in spite of its rather restricted use, has been the object of attention for many researchers in the past half century. However, such work was performed on special experimental lots of metal made in small quantities by a variety of reduction methods. Not until 1946 was there a substantial production of beryllium metal, and not until 1950 was there a steady production of a commercially standard beryllium in the United States. This output was both the result of a requirement of the Atomic Energy Commission for a high grade beryllium of consistent quality and the development of a powder metallurgy process, by the Brush Beryllium Co., known originally as Process Q, which yielded a fine grained beryllium suitable for fabrication. Because this powder metallurgy product, known as QMV, superceded other types of metal made previously and represents the great majority of beryllium in use today, it seems worthwhile to present the results of studies on the mechanical properties of this metal as currently made. To the design engineer and the metallurgist, beryllium has extremely interesting properties. It is as light as magnesium alloys while having a stiffness modulus 40 pct greater than steel and a strength-weight ratio superior to titanium and aluminum alloys and aircraft steels. The melting point is high, 1287°C (2348°F), and it has good corrosion resistance both in air and water. Also, it is highly transparent to X-rays and has good heat and electrical conductivity (electric conductivity is greater than 40 pct of Cu). To the atomic energy program beryllium is considered a valuable material because of its low neutron-capture cross section and high neutron-scattering cross section which make it a good moderator and reflector for the lower velocity neutrons. A major technical difficulty limiting the use of beryllium, especially in structural applications, has been its notch sensitivity and consequent room temperature brittleness. Kaufmann, Gordon, and Lillie1 have reported their work on the mechanical properties of beryllium performed from 1946 to 1950. They studied the room and elevated temperature properties of cast and extruded beryllium and extruded electrolytic flake, Table I. Cast and extruded alloys of 85 to 99 pct Be were tested also. They found that extruded metal developed good strength and appreciable ductility in the extrusion direction and that thermal treatment and alloying provided little improvement in mechanical properties. They concluded that preferred orientation and fine grain size were the means of obtaining optimum tensile properties in beryllium. Other investigators have measured and commented on one of the most striking mechanical properties of beryllium, namely, its abnormally low Poisson's ratio.2 Udy, Shaw, and Boulger3 presented the latest published survey on properties of beryllium but their information is based only on published data available before April 1949 and cites little information on metal fabricated by powder metallurgy

Jan 1, 1955

By D. H. Baldwin, R. E. Reed-Hill

Six compositions of polycrystalline ZY-0 alloys, containing up to 4.2 at. pct 0, were tested in tension between 77° and 600° K. The data obtained from each of the compositions corresponded closely to a rela-ion between yield stress and absolute temperature of the form In s/so = BT, where oo is the yield stress extrapolated to zero degrees and B is a constant. In agreement with others who have observed this relationship, it is shown that the activation energy may be expressed as Ho In so/s. In the present specimens Ho is approximately 18,000 cal per mole and is apparently independent of temperature and composition inside the limits of the investigation. It is also demonstrated that this form of activation energy cowesponds to a strain rate sensitivity parameter RT/Ho. Oxygen was also noted to have an effect upon the operative deformation mechanisms. With increasing oxygen concentration there was an increased tendency to observe both nonbasal slip and cross-slip phenomena. Oxygen does not seriously inhibit twinning more than it does slip. Twins were observed in all specimens tested. It is becoming increasingly evident that interstitial atoms in solid solution are able to interact strongly with mobile dislocations. Stein, Low, and seybolt,&apos; have shown that, if the carbon concentration in bcc iron is lowered below the solubility limit, its flow stress temperature dependence is markedly reduced. This suggests that carbon atoms in interstitial solid solution may be responsible for the pronounced temperature dependence of the flow stress normally observed in iron. This view has recently been challenged by Leslie and sober2 who observed a strong flow stress temperature dependence in iron to which a trace of titanium had been added in order to remove carbon atoms from solution. Since the interstitial concentration must be reduced below approximately 1 ppm in order to produce a pronounced effect on the flow stress temperature dependence,&apos; studies of the effect of interstitials on the flow stress in iron necessarily involve serious experimental difficulties in alloy preparation. There are other metals, however, in which strong effects of interstitial solutes upon both the flow stress and its temperature dependence are observed. Of particular significance is zirconium which, according to Domagala and Mcpherson, 3 is capable of dissolving 28.6 at. pct O. The O-Zr alloy system is an almost ideal system for studying the interaction of interstitial atoms with deformation modes since it is possible to form alloys capable of study over an extensive range of compositions. Mills has made such a study using single crystals oriented primarily for single prismatic slip4 and has found an effect of oxygen concentration on the flow stress temperature dependence analogous to that observed in iron due to carbon by Stein, Low, and Seybolt. The present paper is specifically concerned with the effect of oxygen on deformation in polycrystalline zirconium. Although plastic flow in this type of specimen is much more complex than that reported for the single-crystal work, and involves both slip (on several different types of planes) and mechanical twinning, the results of this investigation are in general agreement with the single-crystal observations concerning the effect of oxygen on the temperature dependence of the flow stress. In addition, they also demonstrate that oxygen affects the acting deformation systems. This is in contrast to single-crystal results4 that showed only single slip on a prism plane. EXPERIMENTAL PROCEDURE Material. High-purity hot-rolled zirconium strip, 0.2 in. thick by 4 in. wide, of 0.10-mm average grain diameter, was used for forming alloys. It was obtained from the Carborundum Metals Co., Akron, N.Y., whose analysis indicated the major impurities were, in wt ppm: Hf, 540, C, 145; Fe, 100; and 0, <80. The plate texture was similar to a wire texture, with basal planes generally parallel to the rolling direction and basal poles randomly distributed about the rolling direction. The heat treatments described below did not appreciably alter the basic texture. specimen Preparation. Small threaded-end tensile specimens were machined from the plate with axes perpendicular to the rolling direction. These transverse specimens had gage sections 1 in. long by 0.060 in. in diam. The small gage section diameter was dictated by the fact that the alloys were formed by dif-

Jan 1, 1969

By Robert E. Green, Edmund G. Henneke

Expressions are derived for the orientation factors associated with dislocation damping due to dislocation motion in the basal slip plane. The results of the calculation of these factors for zinc crystals aye pvesepzted and the relevance of these results to ultvasonic-attenuation measuvements is discussed. In this paper expressions are derived for the orientation factors associated with damping of sound waves due to dislocation motion in the basal slip plane of hexagonal crystals. For zinc crystals, the orientation factors for dislocation motion in one slip direction only, as well as for simultaneous motion in all three basal slip directions, have been calculated at 1-deg intervals. The results of these calculations are presented in the form of contour diagrams in a sector of a standard polar coordinate graph. The calculations have been carried out for both the traveling- and the standing-wave conditions. The relevance of these results to ultra sonic-attenuation measurements is discussed. Associated with the calculation of the orientation factors, the modes of elastic-wave calculation were also evaluated, according to the procedure previously employed by Hinton and Green.&apos; The results of these calculations are not presented here since similar results have been reported earlier by Mus-grave.2 However, it should be mentioned that, although the qualitative features of Musgrave&apos;s results are preserved, the quantitative values are somewhat altered since different values for the elastic constants of zinc were used. ORIENTATION FACTORS It is convenient to refer to three different sets of coordinate axes, Fig. 1, in the following calculations. First, there are the Miller-Bravais axes which are used in describing the Miller-Bravais indices of planes and directions in a hexagonal crystal. These axes are denoted in the conventional manner by a,, a,, a,, and c. The second set of axes used is a rectangular Cartesian coordinate system located as shown in Fig. 1. Note that the x axis coincides with the close-packed direction al [2110], the z axis coincides with the c axis [0001], and the y axis is orthogonal to these two lying in the [0110 ] direction. Finally, a form of Eulerian angles is used to locate the position of the specimen axis. The angle between the specimen axis and the c axis is denoted by 0 and the angle between the projection of the specimen axis on the basal plane and the a, direction is denoted by ø. The majority of observations on plastic deformation of metal crystals indicates that such deformation is caused by the motion of dislocations on a limited number of crystalline planes and in a close-packed direction. In crystals with hexagonal symmetry the most prominent slip plane is the basal plane (0001) and the slip directiops- are one of the close-packed directions, [2110], [ 12101, or [ 1120]. To properly set the stage for the following work, several points must be clarified. First, we want to consider the contribution to the attenuation of elastic waves by dislocations only. While the Granato-Lucke, model for dislocation damping is presently the one most quoted, it is not necessary to refer the present work to it. The only assumption that need be made is that the motion of dislocations absorbs energy from the elastic wave and therefore attenuates it. It is immaterial here how this energy absorption occurs. However, because dislocations have been observed to move most freely on the (0001) plane for hexagonal crystals undergoing plastic deformation, it will be assumed that it is the dislocation motion on this plane which attributes to the observed attenuation. The basic orientation factor, Ok, is essentially the same as that used by Green and Hinton for fee crystals,4 defined by the equation

Jan 1, 1968

By H. Schrader, E. Houdremont, H. Bennek

The different influences exerted by the various alloying elements in iron and iron-carbon alloys give rise to a great number of complexities, which are difficult to grasp. It is important therefore to study any systematic relations that may exist between the effects exerted by the various alloying elements, in order to obtain a general classification and thus a clearer conception of the nature of alloy steels. A systematic survey of the alloys of iron, based on an investigation of the binary equilibrium diagrams, was recently published by Wever. Although his work deals little with properties of importance in works practice, its purpose being rather to point out the theoretical agreement among the types of binary equilibrium diagrams and the position of the alloying elements in the periodic system (atomic radii, etc.), the classification proposed nevertheless also suggests relationships among the properties of the alloys in question, even though the alloys may contain carbon in addition to iron and the alloying element. Wever divided the alloys of iron into one group exhibiting an open or enlarged gamma field and another exhibiting a closed or restricted gamma field, with both groups capable of further subdivision depending upon whether a continuous series of solid solutions is formed, or, owing to the separation of compounds, etc., only a limited series. Thus all alloying elements which with iron form a closed gamma field, a "gamma loop," produce alloys that beyond the composition corresponding to the greatest extent of the gamma loop are composed of ferrite alone at all temperatures. Alloys of this composition accordingly are not susceptible to ordinary heat treatment because of the lack of transformations. Steels of this class may thus be divided into steels that contain less than the critical amount of alloying element, and are subject to heat treatment, and those that contain more than the critical amount of alloying element and are not subject to heat treatment. Thus chro-

Jan 1, 1935

By E. L. Corp, J. C. Johnson, W. G. Pariseau, M. Poad, M. E. Fowler

This paper describes a comprehensive geomechanics case study of a full¬scale test stope at the Carr Fork Mine. The mine is owned by Anaconda Miner¬als Company and is located near Tooele, Utah. Large diameter blast holes were used in a new method known as blast hole post-fill (BHPF). The new design proved highly successful in contrast with earlier experience with vertical crater retreat (VCR) stopes. The main geomechanics objective was the estab¬lishment of a design procedure for optimizing stope and pillar dimensions with respect to productivity and recovery. An integrated three-part approach consisting of mine measurements, laboratory testing and finite element calcu¬lations was taken. Independent correlations of 0.88 and 0.89 between calculated and measured displacements and between estimated and observed yield :ones substantiate the finite element design approach using UTAH-II. Subse¬quent stope and pillar design analyses indicate that doubling of the original stope width at 50% extraction is quite possible without sacrifice of safety or stability.

Jan 1, 1984

By Yves Dardel

THE literature concerning the remelting of aluminum and its alloys is very rich. Unfortunately the greater part of the papers about this subject have no scientific value, for the theories or explanations are too often in opposition to the laws of physical chemistry. Furthermore only a few of the methods of purification1,2 are considered in the literature. Hence it has seemed necessary to the author to sketch a general theory of the purification of secondary aluminum. The purpose of the purification is to eliminate the impurities that the charges and the atmosphere of the furnaces bring into the bath during the successive remeltings. Indeed scrap as well as metal can be used when soiled with oil, greases, water, .. , if it has been sufficiently dried and contains oxides. At the melting point of the metal, the oils and greases are decomposed into their constituent elements H2, 02, H2O, C02, CO, CH4, and others. These gases are added to the corresponding gases in the atmosphere of the furnace. The impurities introduced into the metal during the remelting will accordingly be the products resulting from the action of these gases on the liquid bath. The quantity of hydrogen that is soluble in aluminum and its alloys is given by the relation of Sieverts3 as a function of its partial pressure PH2 in the atmosphere [m = K _%/PH, [I]] where K is a constant, which depends only upon the temperature and increases with it. The experiments of Röntgen and Braun4, Röntgen and Möller5, Bircumshaw6 and Winterhager7 have rendered it possible to determine the value of K, when the temperature is inferior to 1.000°K. One obtains: [log K = - 4,702.5 + 0.238 [2]] Besides its usual signification, the term PH2 represents also the internal pressure of dissolved hydrogen, since in the equilibrium, that is, when no gas exchange occurs between the two phases, the pressures of hydrogen in the metal and in the atmosphere must be equal. Eq I shows that when the partial pressure of H2 increases the amount of dissolved hydrogen in equilibrium increases, and that, if the contrary occurs, the quantity of H2 should diminish. However, if for any reason the diffusion of hydrogen is hindered and the total amount of dissolved gas remains constant while the temperature lowers, the internal pressure of H2 increases until it reaches the value of the hydrostatic pressure. At this point, bubbles of hydrogen appear in the bath and escape out of it. The amount of hydrogen in the metal is then limited by a maximum depending on the hydrostatic pressure, which is practically equal to one atmosphere. Indeed hydrogen does not accumulate in the form of a hydride appearing as a separate solid phase. However, even the mechanism of the solubility is not yet elucidated. One does not know exactly as yet, whether the

Jan 1, 1947

By G. E. Agar, P. L. De Bruyn

Flotation is an important example of a chemical process by which one solid may be separated from other solids in a mixture. In contrast to other chemical processes such as leaching and smelting, separation of solids by flotation is characterized by the establishment of contact among three phases. In froth flotation these three phases are the solid to be floated, an aqueous electrolyte solution, and a gas, usually air. The gaseous phase may be re- placed by an organic liquid phase or this organic liquid phase may be added deliberately as a fourth phase. To gain an understanding of the flotation sys- tem, it is therefore necessary to study the chemical and physical properties of surfaces and to establish the effect of changes in composition of the bulk phases on the nature of the three interfaces, solid-gas, solid-liquid and liquid- gas. With very few exceptions inorganic solids are completely wetted by the aqueous phase so that the first step in flotation is to replace partially the solid-liquid interface by a solid-gas interface. This displacement process is accomplished by the addition of suitable reagents to the aqueous phase. The resultant surface reaction leaves the solid surface with a hydrophobic film. Although the primary objective of these reagent additions is to alter the solid surface, chemical reactions between the added chemical species and those species derived from the dissolution of the solids are unavoidable. For a quantitative description of such reactions and for the determination of the feasibility of a proposed reaction, we rely on available thermodynamic data. The application of thermodynamic principles to flotation systems has contributed much to our understanding of flotation. The changes in thermodynamic properties such as free energy and chemical potential are accessible to experimental determination, and a knowledge of their magnitude allows us to develop and predict a chemical mechanism oy which a solid becomes floatable. In this chapter it will be assumed that the reader has a working knowledge of the general principles of thermodynamics and solution chemistry. A complete discussion of the physical chemistry of flotation must include a treatment of solubility relations, complex ionic equilibria, reaction potential, and the elements of electrochemistry, especially those dealing with reversible electrical cells. The principles related to all of these features of the flotation system will not be discussed in this chapter. The discussion will be concerned with the thermodynamics and electrochemistry of surfaces and the electrical double layer model of the interface.

Jan 1, 1962

By W. F. Rogers, J. A. Stewart, P. J. Kalish, E. O. Bennett

Detailed descriptions are given of materials, apparatus and the experimental procedure used to study the effect of bacteria on sandstone permeability. The factors affecting permeability during injection of bacterial suspensions which have been investigated are: (I) concentration of bacteria; (2) core permeability and median pore size; (3) species of bacteria, mode of aggregation and relative size; (4) injection rate or pressure differential; (5) mean pressure; and (6) depth of penetration of bacteria. The investigation demonstrated that bacteria cannot reduce core pertneability to zero and that their effect on permeability is subject to definite limitations. Remedial or permeability restoration studies also were made. Acidization in combination with reverse flow war found to be an effective method for restoring permeability In cores partially plugged with bacteria. The relationship between the bacterial quantities in the laboratory tests and those found in field operations is discussed. The linear laboratory flow data have been translated into terms of field radial systems; these data indicate the most practical methods of maintaining injection rates in the presence of bacteria are to increase injection pressures or hydraulically fracture the formation. INTRODUCTION It has long been known that various bacteria flourish in the above-ground components of oil field water-injection systems. The presence of these bacteria has led to the suspicion that they might enter into the causes for reduction of injection well permeability, but only recently has an attempt been made to describe the effects quantitatively.1 Biocides are used in many cases without a firm knowledge as to whether the bacteria are killed, or if they are, whether the dead cells affect formation permeability. This project was undertaken as part of a study to determine the effect of bacteria, residual oil and precipitated solids such as iron sulfide or calcium carbonate on the permeability of sandstones and to learn whether any of these materials adversely affect brine injectivity in secondary recovery or disposal operations. This report deals with that portion relating to the effect of bacteria. MATERIALS CORES Three different permeability ranges of Berea sandstone cores were used in the study. The range of initial, absolute brine permeabilities kj were: high — 278 to 400 md: medium—130 to 162 md; and low—17.7 to 48.3 md. The permeability data for the cores used in the tests are included in Table 1. All cores were cut to a nominal 1 in. diameter. Following air permeability determinations, they were molded with an epoxy resin in 1.5 in. ID aluminum sleeves. The sleeves had drilled and tapped holes for intermediate pressure connections along the length of the cores. After molding, the high- and medium-permeability cores were trimmed to 4 in. in length and the low-permeability cores to 2 in. These lengths resulted in pore volumes of approximately 10.9, 10.4 and 4.4 ml, respectively, for the high-, medium- and low-permeability cores. Pressure-transmitting channels were drilled through the plastic into the core proper, using the sleeve holes as drill guides. Width and depth of channel penetration into the core proper were approximately 0.03 in. and 0.05 in., respectively. Three pressure taps were used with all cores; for the high- and medium-permeability cores the taps were spaced 1 in. apart; for the low-permeability cores the taps were spaced 0.4, 0.8 and 1.2 in. from the inlet end. Pore size distributions were calculated from restored-state capillary pressure curves for representative cores in each of the three permeability ranges. In each case the pore size range with the greatest percentage of the pore space included the very small pores up to 0.5 micron in radius. The median pore radii were in the 5.5 to 6 micron range for the high-permeability cores; in the 4.5 to 5 micron range for the medium-permeability cores; and in the 3.5 to 4 micron range for the low-permeability cores.

Jan 1, 1965

By C. H. Samans, G. F. Tisinai, J. K. Stanley

The times at which the first detectable amount of a phase forms at temperatures between 900° and 1800°F were determined. Both X-ray diffraction and metallography were used to detect a in highly strained filings; metallography alone to detect it in annealed bulk samples of six different types of stainless steels. The a phase was found to form in accordance with the C-type reaction curve in both austenitic and ferritic alloys. In filings of types 304, 347, and 446, a formed in a few hours, and in types 316, 309, and 310, it formed in a matter of minutes at temperatures corresponding to the knee of the C-curve. Only in the bulk type 309 steel, after 500 hr, and in the bulk type 310 steel, after as short a time as 25 hr at temperature, was n detected; in both instances at approximately the same optimum temperature as in the filings. The annealing temperature affected a phase nucleation only for the filings of type 304 and 347 steels, and for the bulk samples of type 309 and 310 steels. KNOWLEDGE of both the rate of nucleation and the rate of growth of the new phase is required for a complete description of metallurgical rate phenomena. However, data on the time for nucleation alone may frequently be useful in evaluating the tendency of commercial stainlcss steels to form s under various conditions. Very little correlated information of this type is available in the literature. Shortsleeve and Nicholson&apos; indicate that s forms in ferritic 24, 27 and 30 pet Cr steels according to a C-type of reaction curve, and Emmanuel&apos;s&apos; data for austenitic type 310 steel also suggest this type of solid state reaction. In addition, significant, though fragmentary, information has been given by Binder, Dulis and Smith,4 Payson and Savage,.; Guarneri, Miller, and Vawter,8 rerichs and Clark,7 Wilder,5 Lismer, Pryce, and Andrews,&apos; Smith, Dulis, and Link,10 Dulis, Smith, and Houston," and Henry, Cordovi, and Fischer." The bearing of these data on this work is covered in the discussion. The purpose of this paper is to present such correlated data on s formation in AISI type 304 (18 pct Cr-8 pet Ni), 347 (18 pet Cr-10 pet Ni-Cb), 316 (18 pet Cr-12 pet Ni-2 pet Mo), 309 (25 pet Cr-12 pet Ni), 310 (25 pet Cr-20 pet Ni), and 446 (27 pet Cr) stainless steels. Materials and Test Methods X-ray diffraction and metallographic methods were used to determine the first appearance of the s phase in cold worked filings and in annealed bulk samples of seven steels, under various combinations of time and temperature. The rate of growth of the s particles was not determined. Commercial heats of six AISI steels and a low carbon laboratory experimental heat containing about 28 pet Cr were studied. Analyses are given in Table I. Because cold work greatly accelerates the nucleation of s particles, the relative rates of s nucleation in mechanically strained samples, i.e., filings through 120 mesh, were determined for direct comparison with those in annealed bulk alloys of the same composition.

Jan 1, 1957

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By C. Schlumberger

THE object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,1 but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding?2 method, in which a series of measurements are made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is deter-

Jan 1, 1934

By L. N. Brown

The use of sheet and strip metal has increascd rapidly during the last few years and manufacturers have been called upon for an ever-increasing tonnage, better drawing quality, and better surface. The automobile industry is probably the most insistent in striving for a better product and a desire to reduce costs. Confronted by these demands, the mills have directed their efforts toward the delivery of material. Their personnel has been occupied largely with the problems incident to production, as any increase forced the use of new sources of raw material with their problems. These problems, combined with those met in the daily routine, have demanded immediate attention, with the result that the standardizing of heat treatments, quality, or temper, etc., have been neglected. Considerable work in standardizing has been done by many companies, but no acceptable method has been developed. The following method, therefore, is given with the hope that some method that can be accepted by the manufacturers and users may be developed. The problem of selecting a material with such properties that the losses in processing are a minimum is interesting and difficult. A description of the properties required is likewise difficult, largely because of loose terms. Another handicap is the number of methods of testing which have not been standardized and concerning which little information is available. In the selection of drawing or forming stock, it is advisable to eliminate as many variables as possible; consequently the method of testing the material is of the utmost importance. The method should be rapid and comparatively easy of application, as it is more important that a large percentage of the stock be tested with reasonable accuracy than that

Jan 1, 1923

By C.A. Zapffe

Both the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. Bleeding, Rising, and Piping The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinc- tion between bleeding and rising in reference to killed metal.* Porosity Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth&apos; noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel—oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen&apos;s classical work on copper castings,3 soon followed by

Jan 1, 1943

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.&apos; Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By Alfred V. de Forest

We are now assembled in this hall for the eighteenth lecture in honor of the memory of our greatest American metallurgist, Henry Marion Howe. Many of his most intimate contemporaries, led, as was fitting, by Professor Sauveur, have described his vital accomplishments in three fields: as a leader in technical industrial development; in theoretical research; and finally as a teacher and source of inspiration for nearly two generations of students. In 1914 Professor Howe had retired from active teaching, but maintained his laboratory at Columbia University under the care of Arthur G. Levy, with whom he published many of the papers that later were incorporated into his last book, " The Metallography of Steel and Cast Iron." My position at the time was that of personal assistant to Professor Campbell—no pay, no duties, but the great privilege of preparing specimens, taking pictures and attending to some of the current consulting work. Whenever possible, I visited Howe&apos;s laboratory to chat with Levy and gather ideas about the wonderful field of metallography—in which I was a rank amateur, rescued by the quiet enthusiasm of Donald Smith of Princeton from an instructorship in civil engineering. Levy let me act as a fly on the wall during the Professor&apos;s occasional visits. Busy as he was, Professor Howe took the time and trouble to encourage my interest, as he had done for hun- dreds of others. He told me how he went about gathering his own information speculating as to causes, considering experiments, and verifying his conclusions. I ventured to mention some tests I had run on the irregular stretching of wires of different metals. He read the small volume I had prepared of ill-assorted facts and fancies and remarked: "Nobody cares for your theories or the history of your tests. Describe what you found as briefly as possible and perhaps I can help you to publish." Curiously enough, among my discards were some autographically recorded load-versus-electrical-resistance measurements. Taken with inadequate knowledge and equipment, these curves did not reproduce consistently, but if the relationship between strain and resistance had then been explored, the latest type of strain gauge might have been in useful service for the past 25 years. Professor Howe was a gifted teacher, perhaps because he was primarily an ardent and assiduous student. His own eagerness to learn and his willingness to revise and extend his opinions constantly encouraged those of his environment to be diligent and painstaking in the pursuit of knowledge. In honoring his memory, I also wish to bring to mind the kindly, humorous and quiet Levy, and join his name again, as it was for too brief a space in the past, with that of many-sided Henry Marion Howe. Factors oF Impact Strength The subject chosen for the Howe Memorial Lecture by Dr. Gillett last year

Jan 1, 1941

By A. L. Jamieson, H. Rosenthal

The action of mercury on stressed brass to produce cracks was known before Moore, Beckinsale and Mallinson1 showed that actual season cracking did not occur spontaneously but could be induced by ammonia. These investigators studied other substances, including diphenylamine, without finding that anything other than ammonia could cause season cracking Grimston2 reported season cracking in cartridge cases stored in wooden boxes wetted with dilute sulphuric acid pickling solution. Season cracking associated with sulphur dioxide, water vapor and air has been reported by Johnston,3 although he reported that trimethylamine and pyridine did not cause cracking. Jevons4 has ascribed season cracking of brass in certain instances to trimethylamine, "aldehyde amine," "ketone amine" and pyridine, but no experimental work was done evidently to prove this definitely. Pyridine was investigated by Morris,5 who found it to have considerable cracking power. In the present investigation, the object was a qualitative evaluation of a number of representative amines with respect to their ability to cause season cracking. Thus it was desired only that an appreciable vapor pressure of each amine be obtained in order to make the test as severe as possible, without attempting to test equivalent concentrations for comparative purposes. MEthods Specimens TWO types of specimen were used: 1. Unannealed 70-30 brass CUPs formed from 0.040-in. thick sheet. Height of cup Was 13/8 in. and diameter was 17/8 inches. 2. First draw pieces of caliber .50 cartridge cases in the unannealed condition (70-30 brass)- The cups were representative of a thin wall and thin base specimen, whereas the draw pieces have a thick base (1/4 in.) and a thick wall (approximately 3/32 in.). Both types of specimens contained high residual stress and cracked in less than one minute in a solution of I per cent mercurous nitrate and I per cent nitric acid provided that this was receded by a 30-sec. pickle in 40 per cent nitric acid. Specimens were prepared as follows: (1) degreased in trichlorethylene, (2) rinsed in H2O, (3) pickled 5 min. in 10 per cent by volume H2SO4 (1.84 SP. gr.), (4) rinsed in H2O, and (5) dried. Amirtes Tested In selecting the amines, representatives of the three series of amines, and one series of substituted amines were chosen. The aliphatic series was represented by the methyl and ethyl primary, secondary and tertiary amines. These are the simplest aliphatic amines. For the aromatic series, the phenyl primary, secondary and tertiary amines were selected as being the simplest. The heterocyclic series was represented by pyridine, which is a simple heterocyclic base (tertiary amine).

Jan 1, 1944