Search Documents

By A.S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By G. Ansel, J. P. Doan

THE important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holub1-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength, and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British. Patent 5111376 relates to the parent discoveries of Sauerwald, Eisen¬reich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature" has been found to the particular characteristics of wrought Mg-Zn-Zr alloys, with which the present paper is concerned. - The work to be discussed represents essentially an extrusion study of the Mg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metal¬lography, and toughness of these alloys. Compositional variations are limited to the ranges o to 7 per cent Zn and o to I per cent Zr. EXPERIMENTAL PROCEDURE Alloying and Casting Alloying ingredients were cell mag¬nesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl2 and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manu¬facturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zir¬conium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux¬inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1946

By J. W. Bolton, S. A. Weigand

This paper discusses some fundamental metallurgical principles involved in production of sound cast bronze. In a previous paper the writers advanced the theory that "oxidation" in bronze castings is due to incipient shrinkage, and showed the effect of reducing melting atmospheres.' In the present paper the effects of certain impurities and of actual oxidizing conditions are shown. The appendix deals with the appearance of various inclusions. For many years the prevailing opinion has been that unsoundness, dark colored fractures and other phenomena accompanying porosity and weakness in bronzes are due to oxidation. The actual troubles are caused by fissures of intercrystalline type, which are often mistaken for intercrystalline films. These weaken the metal and make it porous. Grave doubt regarding the accuracy of the oxidation theory appears when several research papers presented within the last 10 years are reviewed critically. In 1919, Comstock2 conducted metallographic researches, attempting to identify "oxides" in synthetically prepared metals. He found that oxides of tin, aluminum, zinc, etc. are different from the intercrystalline films (or cavities) to which porosity is due. Apparently he believed that these "oxide films" may be caused by volatile oxides of zinc or of phosphorus or by dissolved gases thrown out of solution during solidification of the metal. In 1923, Woyski and Boeck3 definitely questioned the accuracy of the oxidation theory and indicated the danger from reducing atmospheres. They say that "oxidation, gassing and shrinkage may produce effects very similar." In 1926, investigations by Iwasé4 showed marked change in absorp-tion coefficients for various gases in copper above and below the liquidus.

Jan 1, 1930

By M. P. Tixier, F. Segesman

Explanations bused on theory and laboratory tests tire offered for certain unusual features of SP logs which may befog their interpretation, namely the "sawtooth" SP and the reduction or increase of SP with time. The sawtooth SP is frequently seen in SP recordings of thick, very permeable watcr. sands of the Louisiana Gulf Coast. Using SP data from a resistor network analog, this anomaly is explained on the basis of a thin shale streak within the sand. under which the invading filtrate accumulates by gravity segregcitiorr. The electromotive force then appearing across the shale streak gives rise to the anomalous SP. Reduction of the SP on successive logging runs Ira often been observed in very permeable sands when as indicated by the resistivity curves, the invasion depth has been reduced to practically zero. Laboratory results verify that this phenomenon may be due, to the presence of air electromotive force, across the mod rake when the fluids on either side differ in activity. Also, there is, in some cases; an increase of SP deflection on successive logging runs, because the emf initially present across the mud cake disappears as the somewhat saline water just behind the mud cake is progressively flushed out by the invading filtrate.. Field example and laboratory data are presented. I N T R ODUCT1ON Some unusual features are frequently observed on certain SP logs which make interpretation difficult. The purpose of this paper is to offer explanations of several cases of interest. All of these arc related to the conditions of invasion. The cases to be discussed are as follows. 1. The sawtooth SP anomaly which is frequently seen within the thick, highly permeable saltwater sands of the Louisiuana Gulf Coast 1. Reduction of the SP deflection from the usual sand line in very permeable sections when the depth of invasion is practically nil. As will be explained, such a reduction is attributable to a membrane electromotive force across the mud cake. 3. An increase of the SP with time just after the iormation is drilled as a result of progressive flushing of the invaded zone. FUNDAMENTALS OF SP PHENOMENA An explanation of SP phenomena must begin with the following basic ideas. 1. The SP log derives its character from ohmic potential differences in the hole produced by currents flowing through the mud.' These currents are driven by electromotive forces which are primarily electrochemical in origin. Other possible types of SP-producing electromotive forces may be disregarded for the purposes of this paper. 2. The electrochemical emf's associated with permeable formations are now understood to consist of liquid-junction emf's and membrane emf's.',' As schematically shown by thc battery symbols in Fig. 1, the liquid-junction emf, E,,,, exists at the contact between waters of different chemical activities, a,,,, (mud filtrate) and tr,,. (formation water); the shale membrane emf, lS.sn. exists across the adjacent shales whcn they separate waters of different activities. The emf's just cited are additivc in producing SP currents (arrowed circles of Fig. I). Thus, neglecting for the moment any possible membrane emf across thc mud cake, the total electrochemical emf, E,, will be given by their sum, where K,., -! K,q,, = 12 + 59, or 71 at 75 °F. In the log interpretations the SP of a thick sand (i.e.. the static SP) is generally related to the activities of the filtrate and formation water through Eq. 1. by setting the static SP equal to - E,.

By J. G. Eenink, R. A. Cunningham

One phase has been completed of a laboratory invesrigation of formations with relatively high permeability under conditions of overburden, formation and mud coltrmn pressures. The following statements are based on these tests within the limitations described. Drilling rate decreased when mud column pressure was greater than formation pressure. The decrease was primarily due to a layer of cuttings and mud particles held to the hole bottom by the difference in pressure. Much of the force of the bit was wasted in this layer and was unavailable for penetrating virgin formation. Adequate jet velocities helped clean the filter cake and chips away and resulted in increased drilling rate — the higher the jet velocity the faster the drilling rate. Drilling rate increased slightly when formation pres sure was greater than mud column pressure. The i11(reuse resulted from cleaning the hole bottom as formarion fluid flowed into the borehole. Overburden pressure had practically no effect on drilling rate. INTRODUCTION Some formations are difficult to drill in a wellbore hole but are easily drilled under atmospheric conditions in the laboratory. The reasons for this apparent difference in drillability are not fully understood. An increase in formation compressive strength causes a reduction in drilling rate. It has been shown by Griggs1, Handin2 and others3-1 that formation strength increases under conditions of high hydrostatic stress. Based on these results, a decrease in drilling rate would be expected with increased drilling fluid pressure in formations of low permeability having low formation fluid pressure. Such a decrease has been shown by Murray. et a1 and Eckel" This effect holds even when using nitrogcn under high pressure as the drilling fluid (unrc-ported tests from the Hughes laboratory). Poor bottom-hole cleaning may account for decreased drilling rates. Even though it may not be easily explained, evidence of poor cleaning can easily bc seen. One evidence is the increased drilling rate that accompanies decreased balling obtained with addition of oil in some muds used to drill shales.4,7,3 Many variables can affect drilling rates. These may include mud composition and properties, formation properties, bit types and operating conditions, formation fluid, mud column and overburden pressures. These must be studied a few at a time under carefully controlled conditions which simulate actual conditions as closely as possible. The purpose of this work was to investigate effect of overburden, formation and mud column pressures on drilling rates in permeable formations. These tests were suggested by conditions shown in Fig. I. Represented is a borehole drilled into a formation with relatively high permeability. In the vicinity of the hole bottom there exists a mud column pressure, P a formation fluid pressure, P and an overburden pressure, The mud has low water-loss properties and sufficient weight to more than overbalance the formation pressure. Laboratory investigation included a range with formation pressure greater than mud column pressure. NOMENCLATURE Pm mud column pressure = pressure of drilling fluid or mud at hole bottom Pf, formation pressure = pressure of fluid in intersticies of formation

By Wieland D. R., Hurst R. E., A. R. Hendrickson

Analysis of acidizing techniques, in correlation with reservoir data and a backlog of past treatments, has resulted in the development of a valuable engineering guide for planning acidizing treatments. Such treatments fall into three categories: (I) acid injection into the pores of the matrix; (2) acid injection into natural formation fractures at less than parting pressure; and (3) combination acidizing-fracturing treatments in which acid solutions (without propping agents) are injected at treating pressures sufficient to open and extend fractures through which the acid flows. Because the spending tirnze of acid during a specific well treatment does not change appreciably, maximunl penetration is attained when the first increment of injected acid is completely spent. Additional acid injection cannot be expected to further extend the benefits of the treatment. Depth of penetration will depend upon the reaction rate of the acid under treatment conditions, the injection rate of the acid into the matrix or fractures and the area-volume relationship existing in the flow channels. Based on Darcy's flow formula, extremely low injection rates must be used in order to keep bottom-hole injection pressures below formation fracturing pressure. As a result, only limited penetration of unspent acid will occur. Treatment records indicate that, in most acidizing treatments, formation parting pressures are exceeded, greatly extending acid penetration. Under these conditions, stimulation benefits are limited to the fracture area produced during the spending time of the first increment of acid injected into the formation. This area may be calculated from laboratory and well data to estimate depth of penetration. This, in turn, may be correlated with productivity data to assist The art of gas and oil well acidizing has been characterized by many changes in treating materials and techniques since its inception. These developments have been designed to provide greater production increases. prolong production declines and shorten payout time. Such improvements have been based primarily on data derived from laboratory research and field experience. As more of the variables influencing these treatments have been recognized and evaluated, acidizing has become less of an art and more of a science. Recent studies of fracturing treatments,' in light of individual well conditions and the results of thousands of fracturing treatments, made possible the formulation of an engineering guide that is now being used to select optimum treating techniques and to forecast probable results of such treatments. A similar analysis of the factors controlling acidizing treatments has been made and is the basis for this paper, The findings herein can be used as a guide in the selection of acidizing solutions and techniques, tailored to fit specific well conditions and to provide optimum stimulation per dollar cost. Acidizing treatments may be classified into three basic categories—(1) treatments in which the acid is injected uniformly into the pores and flow channels of the matrix, (2) treatments in which the acid enters natural fissures and fractures in the formation at less than fracturing pressures and (3) injection of acid into the formation at a pressure sufficient to open and extend fractures into the rock through which the acid penetrates (without the inclusion of a propping agent). TYPE 1 — MATRIX ACIDIZING This category consists of treatments in which acid solutions are injected into a homogeneous carbonate

By Harry K. Ihrig

The hot-working of iron and steel is an art dating back to antiquity, but until about 25 years ago, relatively few alloying elements were used, and these were present only in small percentages. With the exception of sulphur, the amounts of other elements in steels did not markedly affect their hot-workability. The references in the literature on the effect of other elements on the hot-workability of steel are usually reports of failure of these steels in forging or rolling.1-8 With the increased use of alloying elements, and their use in larger amounts, it was observed that many of the new steels were red short in certain critical ranges or at all hot-working temperatures. The stainless steels are particularly difficult to hot-work. The determining of the correct conditions for piercing, rolling and forging of these alloys by experimentation in the mill often results in large losses of these expensive metals. It also is found that the hot-workability limits of many types vary from heat to heat, and hence poor results are obtained on changing to a new heat after a previous one has rolled satisfactorily. To determine the effect on hot-workability of iron to which various elements have been added, it was necessary to devise a method that could be used on small quantities of metal. In such a method, the minimum number of variables should be present, and the procedure should be simple, quick and correlatable with large-scale hot-working operations. Sauveur,9 in the first Henry Marion Howe lecture in 1924, described the effect of carbon on the ductility of steels in torsion near their critical points. He found that carbon increases the plasticity of gamma iron. In the 1930 Campbell Memorial lecture,10 he gives the effect of carbon, chromium, and chromium and nickel on the ductility of steels under 2000°F. in torsion. Ellis11 has studied the malleability of steels at various elevated temperatures by means of a single-blow drop-hammer test. In this test the percentage decrease in height of standard cylinders is taken as a measure of their malleability. He has shown that in the low-alloy steels studied, carbon has a greater effect than nickel, chromium and vanadium. In 1938 the first tests were run on a new quantitative hot-workability test in the laboratories of the Globe Steel Tubes CO. Thum12 mentioned it in 1940. An illustration of the apparatus was published in January 1942.'' The effect of a few alloying elements on the hot-workability of metals was shown in a description of the test in 1944.14 Description of Test Method The method adopted after a trial of several others is a rapid twisting of bars to failure in a furnace. The standard-size bar was chosen as 9/16 in. It is prepared from larger pieces by forging and cold-

Jan 1, 1947

By R. J. Blackwell, J. R. Rayne, J. R. Henderson, W. M. Terry, D. C. Lindley

This paper presents the results of a laboratory investigation of the efficiency of water-solvent mixtures in recovery of oil. These mixtures may have the high displacement efficiencies characteristic of solvent floods and the high sweep efficiencies characteristic of water floods. Thus, the water-solvent process may increase the number of reservoirs in which a miscible-type displacement can be used profitably. The experiments on the use of water-solvent mixtures for recovery of oil were conducted to find the general applicability of the process. These studies demonstrated that, in flowing through sands, water and solvent segregated into a solvent layer on the top and a water layer on the bottom rather than flowing through the sands as a uniform mixture. Calculations based on the simultaneous flow of the water and solvent in layers were used to predict the effective mobility of the mixtures and the optimum operation of the process in steeply dipping, homogeneous reservoirs. As most reservoirs are not suited for the operation of the process under ideal conditions, experimental studies were conducted with sand-packed models scaled to represent more realistic reservoirs. These studies included the effects on recovery of oil of rate of injection, viscosity of oil, variations of permeablity within a formation and variations in water-solvent ratio. For the range of con-ditions studied, higher recoveries of oil were obtained with water-solvent mixtures than with water or practical volumes of solvent alone. INTRODUCTION A group of intriguing—because of their great possibilities—new oil recovery methods at the disposal of the petroleum engineer are the miscible displacement processes. These processes (high-pressure gas drive, en-riched-gas drive and LPG bank driven by methane) displace all of the oil from the portions of the reservoir swept by the injection fluid. The key question confronting the engineer applying one of these techniques to a particular reservoir is, "What fraction of the reservoir can be swept by injection of a practical volume of solvent?"." Intensive laboratory studies have been made during the past several years in seeking answers to the question of the sweep efficiencies which can be expected in solvent floods.' - These studies provided the answer that low-viscosity, low-density solvents channel and by-pass oil in sands with no dip. In horizontal sands, solvent flooding becomes less efficient as the viscosity of the oil increases, the recovery of oil at solvent breakthrough decreases and larger volumes of solvent are required to achieve a given recovery. More efficient displacement of oil by solvent is observed under certain conditions in sands with dip.".' If the permeability and dip of the sand are sufficiently high, gravity segregation of low-density solvent injected updip can prevent channeling. At rates of depletion below a critical rate,"." no channeling occurs. Unfortunately, in many reservoirs, the critical rate is so low that production of oil at rates below this rate is not economically attractive. And at rates over four times the critical rate, channeling is almost as severe in sands with dip as in horizontal sands. These findings pointed out that, for solvent floods to be generally applicable in recovering oil from all types of reservoirs, new methods of improving their sweep efficiencies are needed. Simultaneous injection of water with the miscible fluid was suggested by Caudle and Dyes7 as a method for improving sweep efficiencies. They theorize that water flowing with the solvent would decrease the effective mobility of the solvent and cause it to contact more oil sand. If, indeed, the water and solvent flowed as a uniform mixture, the process should have the advantages of the high displacement efficiencies characteristic of miscible floods and the high sweep efficiencies of water floods. Thus, the method (at least in theory) would greatly increase the number of reservoirs in which miscible-type displacements would be feasible. A research program was conducted to probe the technical feasibility of the water-solvent process. It

By R. W. Fountain, W. D. Forgeng

A new constitutional diagram is presented for the cobalt-rich end of the cobalt-titaniurn system. The modifications result from the presence of a new, intermediate, fcc phase, ?, the existence and homogeneity limits of which were established by metallo-graphic and X-ray studies of alloys containing from about 3 to 30 pct Ti. The precipitation of the ? phase from supersaturated solid solution was studied by hardness and electrical resistivity measzsrements, and two distinct stages in the process were observed. COBALT forms the base for a number of precipitation -hardenable alloy systems which may be divided into two distinct categories of practical interest, a) those hardened by intermetallic compounds and b) those hardened by carbide formation. The precipitation of intermetallic compounds from solid solution in cobalt-rich alloys has, however, received very little attention. Although the phase diagrams for some binary systems capable of precipitation have been determined,' there is an almost complete lack of data on the property changes associated with the precipitation, and even less information on the kinetics of the reactions or morphology of the products. More information is available on the precipitation of carbides because of the practical significance in superalloys. A survey of cobalt binary phase diagrams suggested that the cobalt-titanium alloys might provide interesting and useful precipitation-hardenable alloys. The equilibrium diagram as proposed by Wallbaum2 is shown in Fig. 1. Köster and wagner3 have indicated that the maximum solubility of titanium in cobalt is about 10 pct at the eutectic temperature (1135oC), and this decreases to about 7.2 pct at room temperature. The temperature of the allotropic transformation in cobalt is lowered by the addition of titanium, about 5 pct being sufficient to retain the high-temperature fcc modification to room temperature. Wallbaum and Witte 4,5 have indicated that the precipitating phase in alloys containing up to about 29 pct Ti is Co2Ti, a hexagonal Laves phase of the MgNi, type. With slightly higher titanium contents, they also report a cubic modification of Co2Ti of the MgCu2-type Laves phase. Duwez and Taylor6 confirmed the existence of the hexagonal (MgNi2) modification but not the cubic (MgCuz) modification of Co2Ti and suggested that existence of the cubic form may have resulted from impurities in Wallbaum's alloys. In their work on Laves-type phases, Elliott and Rostoker 7 reported the cubic modification of Co,Ti, but did not confirm the existence of the hexagonal modification. However, Dwight8 in a discussion of the work of Eliott and Rostoker again showed the existence of both modifications of Co2Ti, a result which was confirmed at that time by Elliott and Rostoker. As a result of a study on the iron-cobalt-titanium system, Köster and Gellers suggested the existence of a Co3Ti phase isomorphous with Fe3Ti. Witte and Wallbaum,' however, established the fact that no compound, Fe3Ti, exists in the iron-titanium system, and in a later publication, wallbaum2 stated that Kitster and Geller's reasoning was not valid, and no compound, Co3Ti, exists. This conclusion was later acknowledged by Köster.10 Preliminary experiments by the present authors to determine the precipitation-hardening characteristics of the cobalt-rich, cobalt-titanium alloys re-

Jan 1, 1960

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130°F. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric Pressure and by heat transferred to it from rock at high temPerature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. Methods Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1943

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935

By G. U. Greene

The various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulphur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1)† states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As. Experimental Work In the present research, the author used for methods in an attempt to determine the composition of the various phases: (1) chemical, (2) microscopic, (3) roentgenographic and (4) thermal. Previous to this research, considerable time had been spent making analyses of different speisses, but unfortunately no very definite conclusions could be made as a result of these analyses.

Jan 1, 1937

By Frederick Becket

DOCTOR Albert Sauveur, distinguished scientist and Honorary Mem-ber of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future respon-sibilities with which it is accompanied. Several of the previous lecturers had the good fortune to attend the classes of Professor Howe and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence. of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it.

Jan 1, 1938

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By S. C. Oliphant, R. Floyd Farris

Presented in this paper is a summary of the results of experiments conducted in both the laboratory and the field during the past three years in connection with casing-perfora. tion problems. Included are studies of gun features that influence bullet performance and penetration, and studies of the effect of perforator bullets on casing and the neat cement in the annulus. Discussion and data are also presented relative to the accuracy of depth measurements in deep wells. Introduction It is a common practice in the oil industry to effect the completion of oil wells by setting and cementing casing through the producing horizons and perforating the section of casing opposite the desired interval by means of a gun lowered into the well on a cable or on the tubing. This practice has been followed for some time, and this method of completion has been given considerable study by the companies that render perforating service as well as by the oil companies that utilize their services. Through continued research on this subject, it has been possible to develop guns, bullets, and powder that will permit controlled firing at great depths, and penetration of as many as two strings of casing. It is the object of this paper to present the results of studies made of gun perforating in both the field and the laboratory. These studies were made to determine the factors that affect penetration of the bullet, burring of the casing, accuracy of depth measurements, and other items. It is hoped that by presenting the results of these investigations a better understanding may be obtained of certain of the factors involved in gun perforating and further investigation of the subject will be prompted. Subsurface Tests A well approximately 9000 ft deep, which was being prepared for abandonment, was selected for subsurface tests of gun-perforating experiments, In preparing the well for the experiment, 51/2-in. casing in the hole was pulled and racked in the derrick. A test section of pipe, which consisted of 65 ft of 5-in. 18-lb J-55 casing centered inside 7-in. 28-lb N-80 casing, was placed in the derrick corner and the annulus between the two pipes was cemented from the bottom up with 161/2 lb per gal neat cement, which was mixed and displaced with a cementing truck in the usual manner. After the cement had been allowed to harden for about a week, the test section was lowered into the hole on the 51/2-in. casing to a depth of 6600 ft by casing measurements. The hole was filled with drilling fluid weighing 10 lb per gallon. A perforating company was called to perforate the pipe, but was not advised that an experiment was being conducted. The company was asked to check the total depth (to cross pins in the bottom of the test section), then to raise the gun a given distance and fire a given number of shots with 1/2-in. bullets, pick up another distance and fire a given number of 3/8-in

Jan 1, 1947

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By D. J. McAdam, R. W. Mebs

THE technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture, According to the prevalent view,8 the technical cohesive strength of a metal, in any particular state as regards prior mechanical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress.? In two previous papers by one of the authors,14,15 evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.8 In this paper, as in the previous papers,14,15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated S3, and the intermediate principal stress will be designated S2. The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress." 14,15 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,"' however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average of the three principal stresses.* This influence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers, 14,15 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant conclusions are derived from experimental data obtained by other investigators. They are based chiefly on results of tension tests

Jan 1, 1943