Search Documents

By W. B. Hickman, J. J. Pickell, B. F. Swanson

Many physical properties of the porous media-immiscible liquid system are dependent upon the distribution of fluids within the pores; this in turn, is primarily a function of pore structure, liquid-liquiri interfacial tcnsion and liquid-solid wetting conditions. The cnpillary pressure hysteresis process provides a means of investigating the influence of pore structure upon fluid distribution for consistent sur/acc conditions. Invcstigntiot2s indicate that residual non-wetting-phase saturations /ollozuir,g the imbibition process (i.e.,wetting phase displacing nor2-wctting phase) are dependent upon both pore structure and initial non-raetting phase saturation and suggest that residual fluid is distributed as Discontinuous ,globules, one to a few pore sizes in dimension, thrnugh the entire range 01 pore sizes originally occupied. It clppears that air-mercury capillary pressure dala adequntely rellect the distribution of fluiris in a water-oil system when strong wetting condition preliczil. An oil-air counter-current imbibition technique has also been found to provide a rapid rneans of obtaining residual-initial saturation data. In a majority of cnses, rcsidual saturations detf-rniinecl from the oil-air or air-mercury process reasonably approximate residual oil saturation following water drive of a strongly water-wet medium. INTRODUCTION A reliable estimate of recoverable reserves depends not only on the amount of original oil-in-place but also on pore geometry and distribution of fluids within the pores. A critical parameter determining the recovery from a reservoir under waterflood, for example, is the amount and distribution of residual oil within the various rock types present. The purpose of this paper is to investigate the mechanism of capillary trapping and assess its importance in laboratory measureqents of residual oil saturation. The degree of wettability of a reservoir rock is recognized as an important factor in waterflood or imbibition experiments. In this paper, however, only the water-wet case has been considered. Considerable experimental evidence1 suggests that for water-wet rocks, capillary forces predominate in tile distribution of fluids and that viscous forces in the range normallv of interest in the reservoir have a minimum influence on residual oil saturation. It follows that if the ultimate recovery is controlled by pore geometry, a unique residual non-wetting phase saturation should exist for a given set of initial conditions. Two laboratory procedures.found to be extremely useful in the study of pore structure and degree of fluid interconnection at various saturations are decribed. Although air-nercury capillary injection curves have been used2 previously to characterize the drainage case, the withdrawal or imbibition case can provide valuable supplementary data. The air-mercury process, however, has several disadvantages; it is difficult to run in a sufficiently accurate manner, mercury does not always act as a strongly non-wetting liquid and in the air-mercury process the sample is rendered unsuitable for future analyses. An alternative process is described in which air is the non-wetting phase and naptha, hentane, octane or toluene is the wetting phase. INTERFACIAL TENSION AND CAPILLARY PRESSURE Interfacial tension between immiscible fluids is due to the difference in attraction of like molecules as compared with their attraction to molecules of the neighbouring fluid. This net attraction results in a tension at the interface. To extend the interface; thus, interfacial tension s can also be thought of as free surface energy. Interfacial tension is normally expressed as dynes/cm, and interfacial energy is measured in ergs/cm2 hence, both have dimensions ml A 2 and are numerically equal.

Jan 1, 1967

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By Robert B. Sosman

THE chance that a Howe Memorial Lecturer will be able to refer back to a personal contact with the distinguished metallurgist for whom this lectureship is named grows steadily smaller. I did not have the pleasure of his personal acquaintance, but I did receive from him in 1916, quite unexpectedly, a letter commenting on a paper that I had recently published27 on "Types of Prismatic Structure in Igneous Rocks." The paper was written for geologists and petrologists, but it had an application, naturally, to the crystallization of iron and steel in a mold. The letter impressed me at the time, and still does, with the breadth of Professor Howe's interests and his perseverance in keeping up with the progress of any branch of knowledge that had metallurgical connotations. SCOPE OF THE LECTURE During several years preceding the date mentioned I had worked in collaboration with Arthur L. Day and E. T. Allen8 at the Geophysical Laboratory, Carnegie Institution of Washington, on the temperature scale as defined by the nitrogen thermometer at high temperatures. Later (1928-1947) I had the opportunity of helping to apply this experience to the pyrometric problems of the steel industry. Because of the range of its temperatures, the multiplicity of the methods used, and the variety of its purposes, pyrometry in the open-hearth process has always offered a fertile field for both research and development. I am therefore devoting an hour to the subject of temperatures in the basic open-hearth furnace, the furnace that makes most of our steel in the United States. I would direct your attention particularly to the choice of the first two words in the title of the Lecture. One sometimes hears or reads of the "temperature of such-and-such a furnace," as if it were a single, measurable, characteristic quantity. I need hardly emphasize to any one who has ever operated a furnace or a kiln that "temperature of the furnace" is a meaningless phrase. Even if we confine our attention to the space enclosed by the roof, walls, and hearth of an open-hearth furnace, it is doubtful whether any such space has ever been so uniform in temperature that the phrase would have a meaning. In any furnace, there are many different temperatures, capable of being measured at many different places, and actually being measured for several different purposes. These pyrometric purposes, methods, and results, if given in detail, would expand this lecture into a book on the basic open-hearth process. I must therefore confine myself to a statement of the range of temperatures as they have been observed in various parts of the furnace, indicating in a general way why they are measured, and mentioning the methods that are available without attempting to describe these

Jan 1, 1948

By C. Dalton, H. L. McGill

The purpose of this study was to develop a method for predicting the time delay created by metering a fluid through an annular restriction with translational motion of the boundaries. This time delay is utilized to control the opening of valves in various down-hole oilfield tools and forms the basis for the "hydraulic jar". The hydraulic jar is used to give upward impact forces to tubing or other tools that become lodged down-hole. The design of these jars has primarily been by trial and error; varying the clearances, fluid viscosities and dimensions of the jar until a satisfactory time delay was achieved. Obviously, a better understanding of the fluid flow characteristics is required to produce designs that are satisfactory and to eliminate the trial-and-error approach. Previous studies of flow in annular spaces were based on constant length of the annular restriction. Any motion of the boundaries of the annular space was confined to a rotational motion, like that encountered in journal bearing design. Consideration of the effect of translational motion of one boundary with respect to the other was necessary in applying this previous work to a time delay device. A prediction method was developed that takes into account this relative translational motion. Equations were developed to predict the relative velocity, the flow rate, and the time delay in a concentric annular space. The effect of eccentricity also was included. Experimental data were obtained and closely correlated with the prediction method. This correlation is presented graphically in terms of predicted and actual relative velocities for various annular clearances and pressure drops. This extension provides design equations which predict the performance of the hydraulic jar, thereby eliminating trial-and-error solutions and reducing the development time required for satisfactory designs. INTRODUCTION The design of down-hole oilfield tools which use hydraulic delay systems based on flow through annular orifices with relative motion of the boundaries is usually a trial-and-error process. The annular clearances, fluid viscosities and dimensions of the mechanisms were varied until satisfactory delay times were obtained. The development of these tools has been expensive, and a better understanding of the characteristics of annular flow with relative motion of the boundaries could result in superior and less expensive designs. The purpose of this investigation was to provide a method of predicting the performance of down-hole tools which use annular flow and, in particular, the performance of a down-hole tool known as the "hydraulic jar". The hydraulic jar is used to free pipe, packers and other tools that become lodged down-hole. The jar, located in the tubing string between the surface and the object which is stuck, releases the object though the repeated application of upward impact blows. The jar is basically a slip joint that is restrained in a collapsed condition until the desired tubing tension has been developed. The slip joint is then released and accelerates rapidly until it shoulders, delivering an impact blow or jar to the object. The delay obtained by metering the fluid through the annulus formed by the jar valve and housing provides the time delay necessary to stretch and apply tension to the tubing or pipe. Fig. 1A gives a schematic diagram of the hydraulic jar and brief details of its operation. The metering of the hydraulic jar begins when the tension force being applied to the jar by the pipe creates a pressure differential across the valve that is approximately equal to the force divided by the displacement area of the valve. This pressure differential induces flow through the annular restriction formed between the valve and housing. The valve moves with respect to the housing as the

Jan 1, 1969

By E. W. Engle

For several years the Fansteel Products Co. has been engaged in e production and development of various of the rarer metals. It is at present engaged in the commercial production of tantalum, tungsten, and molybdenum in a very high state of purity. The information contained in this paper is partly a general compilation from various sources and partly information obtained as a result of recent years of work in the laboratory of this company. Tantalum, tungsten, and molybdenum form a group peculiar to themselves among the commercially available metals. Their very high melting points (tantalum 2770' C., tungsten 3350' C., and molybdenum 2550" C.) set them apart so far as the metallurgical processes for their production are concerned. Further, when properly prepared and treated they will stand a somewhat unusual degree of cold work, that is work below the temperature at which marked crystal growth takes place. Such cold-worked metal may show a high tensile strength; tantalum to 130,000 lb. per sq. in., tungsten to 490,000 lb., and molybdenum to 260,000 lb., in the form of fine wire. In physical appearance, these metals are not unlike some steels; they may be better described by saying that polished tantalum somewhat resembles lead; polished tungsten, iron; and polished molybdenum, nickel. The polished surfaces of all three remain untarnished in ordinary air. Air containing corrosion-producing impurities will, in general, show molybdenum the least resistant to corrosion and tantalum the most resistant. Molybdenum has, however, a high degree of resistance to corrosion by hydrochloric acid, a property that should render it of commercial interest. On the other hand, it is markedly attacked by some of the weaker organic acids. The three metals oxidize rapidly when heated at or above a dull red in air. This feature limits their use in many applications where their high melting point and strength make them appear usable. Tungsten and molybdenum, at red heat, are quite inert to hydrogen and nitrogen; while tantalum has a rather remarkable affinity for all the ordinary gases, which results in its becoming embrittled in their presence. This

Jan 1, 1925

By William Campbell

In the olden days the making of alloys was an art, and the secrete of the craft were jealously guarded. To-day it has become a science, though the old ideas in regard to the secrets and formulæ are dying hard. Modern progress may be attributed to scientific research and testing of materials, and the substitution of chemical analytical control for " cook-book " methods. We know to-day a great deal about the constitution of alloys, the reasons of the change in structure and physical properties by heat and mechanical treatment; and this new knowledge is due for the most part to the physical chemist and metallographist, who have shown us that alloys are simply solutions, and as such obey definite laws. The application of the theories of solutions and of the phase rule tells us what ought to happen when our alloys are in a state of equilibrium. The working-out of the temperature-composition diagram (thermal diagram) for numerous alloys has thrown a light on the structure and constitution which has dispelled most of the darkness in which we labored before the advent of metallography. The work began with the determination of the freezing-point curves, and here the research of Le Chatelier,' Gautier,2 Roberts-Austen,3 and the other pioneers broke the ground. Next the physical chemists, Tammann,4 Rooseboom,5 Bancroft,6 and their colleagues, showed us the complete thermal diagram and its meaning. Then the researches of Heycock and Neville7 on the Cu-Sn series and of Shepherd 8 on the

Jan 1, 1913

By F. E. Buch

THE Smelter is designed for a production capacity of 10,000 short tons of blister copper per month, when operating on the present concentrate grade. The Smelter lay-out is shown in Fig I. The major units of equipment comprise two reverberatory furnaces, three 13 by 30 ft Peirce-Smith converters, two straight line casting machines, one being served by a 13 by 30 ft holding furnace and the other by a ladle tilting quadrant, two converter ,aisle cranes and two converter blowers. The plant is compact and the general arrangement of standard gauge railway tracks and conveyor belts provides for a smooth flow of incoming materials and metallurgical products. Concentrate is received by conveyor belts and fluxes in standard railway trucks. The local track system is covered by an electric trolley locomotive. The Smelter treats a wet (10 pct moisture) flotation concentrate containing approximately 53 pct total copper and 0.9 pct oxide copper. The predominating minerals are chalcocite, chalcopyrite and bornite accompanied by small quantities of malachite and cuprite. The gangue is highly siliceous and requires limerock as a flux. Metallurgy would be straightforward were it not for the necessity for eliminating k bismuth which occurs as an impurity in the ore along with the copper. Directly or indirectly most of the Smelter problems can be traced to the necessity for bismuth removal. Copper recovery, based on new copper treated, averages 97.5 pct. GENERAL DESCRIPTION Flotation concentrate, containing to pct moisture, is conveyed from the filter plant to the smelter storage bins by conveyor belts, the material being weighed in transit by a revolving drum type of weigh-hopper manufactured by Samuel Denison and Son, Ltd. The weigher consists of a steel drum with dished ends carried on a horizontal shaft and rotated by an 8 hp squirrel-cage motor through a worm and spur reduction gear. A feed mouth in the drum permits of filling and discharging. The whole unit is supported on a framework resting on weighing levers, which in turn connect to transfer levers, thence to an indicator of the steelyard type situated 16 ft from the centre line of the drum. The indicator is of the "Denison" patent equilibrium controlled ticket stamping type, insuring mistake-proof records by a combination of electrical and mechanical movements which prevent the operator from printing until the cover enclosing the steelyard is closed and until the poise-weights have been set correctly to the weight of the hopper and contents. The machine is capable of weighing 30 short tons at a time but the usual load is 28 tons. After obtaining the gross weight the drum is rotated and discharged into a receiving bin situated below it. The empty drum is weighed and the net weight re-

Jan 1, 1947

By Jim D. Mote, Eugenia M. Howard, Willis L. Barmore, John E. Dorn

The effect of stress and temperature on the creep rate of Ag-33 at. pct A1 and Ag-33 at. pct Al-1 at. pct Zn for prismatic slip was determined over a range of temperatures from 440º to 700°K. The alloys exhibited a brief initial inverted transient creep over which the creep rate increased slightly to a steady-state value which depended only on the stress and temperature, regardless of the previous strain history. The steady-state creep rates were found to be given by: where the activation energy is independent of the stress and strain and agrees fairly well with that estimated for diffusion. The observed creep behavior was shown to be in qualitative agreement with a model based on the stress-induced local disordering in the vicinity of a dislocation. OVER the past fifteen years, considerable progress has been made in correlating the experimen-entally observed plastic behavior of pure metals over each temperature range with one or more of a series of theoretical strain-rate controlling dislocation mechanisms. Despite the current interest in the plastic behavior of intermediate phases and inter metallic compounds, however, very little has been done in identifying the operative dislocation mechanisms in these materials. It is anticipated that the plastic behavior of intermediate phases can be rationalized in terms of the same dislocation mechanisms that are appropriate to pure metals and a solid solutions, provided the additional complexities arising from crystal structure, bonding, long-range order, short-range order, and defect lattices are taken into account. As part of a more extensive investigation on the plastic behavior of intermediate phases, Mote, Tanaka, and Dorn1 recently reported on the effect of temperature on the yield strength for prismatic slip in the hexagonal Ag-33 at. pct A1 intermediate phase as recorded in Fig. 1: Over Region I the deformation was observed to take place as a result of the thermally-activated Peierls mechanism, and over Region II the athermal disordering mechanism applied. The experimental data at that time, however, were not sufficiently extensive to identify the thermally activated mechanisms operative over Region III. It is the purpose of this investigation to attempt to identify the mechanisms that are operative over this high-temperature region. It will be shown that the same mechanism operates all over Region Ill, although the activation energy for this mechanism is in good agreement with that for diffusion, the process cannot be attributed either to the motion of jogged screw dislocations or the climb of edge dislocations. The results, however, are in good qualitative agreement with stress-induced disordering localized at dislocations. EXPERIMENTAL PROCEDURE The alloys studied in this investigation were prepared from silver, aluminum, and zinc (each of purity greater than 99.995 pet) by induction melting under an argon atmosphere and chill casting in a copper mold. Rectangular bar single crystal specimens (1/4 by 1/8 in. in cross-sect ion) of Ag-33 at. pct Al were grown in vacuum by a modified Bridgman technique. Similar Ag-33 at. pct Zn specimens were produced by an identical technique employing an argon atmosphere. The specimens were so oriented that the angle 90-Xo between the tensile axis and the normal to the prismatic plane and the angle A, between the tensile axis and the slip direction were 45 ± 1 deg. The effect of a change in temperature on the creep rate and a change in stress on the creep rate were determined over the temperature range

Jan 1, 1963

By C. A. Zapffe

BOTH the foundryman and the theoretical metallurgist are now generally agreed that the anomalous "rising" or "bleeding" of certain ferrous castings of killed metal is primarily attributable to hydrogen. How and why the phenomenon occurs, however, have not been made clear. The following discussion is intended to harmonize foundry experience with metallurgical theory so that the foundryman may possibly improve his ability to prognosticate whether a certain casting may bleed or not. BLEEDING, RISING, AND PIPING The "rising" to be discussed here is not to be confused with the action in rimming ingots as a result of the carbon-oxygen reaction, although a conclusion will be drawn that may apply to the art of controlling the rimming action. Only killed metal is considered, which includes both steels and irons. In Fig. I, three killed, chill-cast ingots are shown: a porous ingot whose evolution of gas during late stages of solidification has ejected metal through the top; an ingot in which moderate gas evolution during solidification has lifted the mushy central metal, i.e., it has "risen"; and, third, a sound ingot with good piping characteristics. The first type is referred to as "bleeding," and generally infers that a solid skin had first formed through which the liquid metal later erupted. There is no fundamental distinction between bleeding and rising in reference to killed metal.* POROSITY Hydrogen appears as a cause of bleeding because the gas evolution simultaneously leaves a porosity of a type traceable to hydrogen. Twenty years ago, Melmoth1 noted that killed steel that rose unexpectedly in the mold, if returned while liquid to the furnace and heated further under a reducing lime slag, would again rise in the mold; but that if the ingot were allowed to solidify and was then remelted no rising occurred. A critical quantity of the responsible gas is therefore removed by the rising action. Melmoth associated rising with high silicon (0.7 to 0.9 per cent) and concluded that silicon increased gas absorption. Because silicon is a strong deoxidizer, oxygen must, therefore, be eliminated from consideration of the three common gases in steel-oxygen, nitrogen, and hydrogen. Butterworth2 later decided that pinhole porosity was caused by gases dissolved in the metal and that hydrogen was obtained from steam in the mold. Allen's classical work on copper castings,3 soon followed by

Jan 1, 1942

By W. H. Coghill, A. M. Gow, M. Guggenheim, A. B. Campbell

The object of this paper is to discuss the fundamental principles of ball milling and to present some observations which have been made in laboratory and plant investigations. The discussion will be limited to wet grinding of ores in cylindrical mills, but doubtless many of the principles involved will be equally applicable in the other fields of fine grinding in which mills of the same type are used. In the concentrators of the United States there are about 650 ball, rod, or pebble mills, operating or ready to operate, and these have about 100,000 connected horsepower. For grinding in cement plants there is about three times this connected horsepower, and other industries have an unestimated amount, all used for the general type of grinding that is to be discussed here. It is true that these figures do not represent stupendous amounts of power, but when one considers that ball milling is often the ((bottle neck" in a concentrator and that it often accounts for the largest single item in the cost sheet, the importance of a comprehensive understanding of the principles of ball milling can be appreciated. Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses, or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespective of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison, a new philosophy in the study of ball milling. Briefly, this '(new philosophy" consists of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced varisbles, with emphasis on the latter.

Jan 1, 1935

Application of technology to the search for new deposits went on apace in 1963. Traditional methods, aided by modern communications, were successful in some out-of-the way corners of the world that had not been adequately prospected, but the co-ordination of several mutually supporting techniques is necessary to define exploration targets in most areas today. Although these obviously include geophysics and geochemistry, which are treated elsewhere in this issue, geology continues to play a major role. As the search focuses on less and less obvious targets there will be more need than ever to "pull out all the stops." Any anomaly may have significance and must be evaluated as a possible lead. Ability to detect them increases as the laboratory workers refine techniques for measuring physical, chemical, and isotopic properties; it will be increasingly the responsibility of the exploration geologist to understand and apply these to economic problems. Simple propecting, the search for outcrops of recognizable ores of traditional types, was perhaps most successful for iron. Potentially large deposits of high-grade magnetite-specularite-hematite ore have been found in the Mary River area near the north end of Baffin Island. The ore holds up four hills that stand some 1500 ft above the surrounding country; obviously they were ripe for discovery by the first person to come across them, in this case Murray Watts, president of British Ungava Explorations, Ltd, As preliminary examination indicates a lump ore averaging 68 to 70% iron, these deposits may be commercial in spite of the unfavorable climate and their isolation from world markets.

Jan 2, 1964

On the following pages are abstracts of papers published by the Institute during the year 1931 as Technical Publications, Preprints, and in bound volumes. For abstracts of papers that appear in bound volumes in 1931 but that were published as Technical Publications in 1930, see the Transactions, 1930. Papers that appear in the volume in which this list is printed are not abstracted here. Many of the Technical Publications have been reprinted in bound volumes. Information regarding this disposition, and number of pages in each paper, may be found in the list beginning on page 616. The abstracts are grouped as follows: Page Page Metal Mining....................... 578 ing and Metallography of Non-Milling and Concentration........... 578 ferrous Alloys)................586 IronandSteel...................... 580 Coal Division.. ................ 592 Petroleum and Gas.............. 598 Mctallurgy......................... 585 .............. 613 Institute of Metals Division (Found- Geophysical Prospecting......... 613 Metal Mining Use of Models for the Study of Mining Problems. By Philip B. Bucky. (Tech. Pub. No. 425, 12,000 words.)—This paper describes a research project undertaken to provide a means of studying the behavior of weighty structures such as mines, dams, foundations, etc., with models of the same material in the laboratory. The paper shows that in general it can be done. The underlying theory is explained, the apparatus which was developed and built to do this is described, and the results of laboratory experiments with sandstone mine structures are given. There is discussion of the accuracy of results with the present equipment, the model size necessary, and of the size and type of equipment necessary for the obtaining of results of practical value in the field. Milling and Concentration Ball Mill Studies, I. By A. W. Fahrenwald and Harold E. Lee. (Tech. Pub. No. 375. 25,000 words.)—This paper presents the results of an extensive experimental study of some of the numerous elements entering into ball mill grinding. All apparatus used was equipped with ball bearings. Every experiment was accompanied by a power measurement accurate to 0.005 hp. Quartz was used. Each element studied, such as ball load, was varied systematically. Power curves were obtained for the mill for three general sets of conditions; namely, (1) balls only (2) balls and quartz and (3) balls, quartz and water. For each general condition, power curves were obtained for various mill speeds, ball loads and ball sizes. For conditions 2 and 3, feed sizc and weight and pulp dilution also were studied as variables. The mill output, in grams of finished product per unit of time, was obtained for each test. In a general way, output (mill capacity) paralleled the power data and this attached

Jan 1, 1931

By T. D. Mueller, H. Dykstra

This paper describes a method for obtaining compositions of gas and oil phases in equilibrium with each other at a given reservoir temperature and pressure as lean or enriched gas is injected into a reservoir oil not in equilibrium with the gas. The method is based on calculation of equilibrium constants, K, from the equation log Kp = A + B F, where p is pressure and F is component characterization factor. A and B are constants that vary with a composition parameter. The paper explains how A and B could be determined with a minimum amount of data. The method consists of calculating equilibrium constants as a function of liquid composition and using the K's to calculate changes in compositiort of injection gas as it successively contacts original resetvoir oil at the gas-oil front and the change in composition of reservoir oil as it is successively contacted by the injection gas in the vicinity of an injection well. An iterative process is required. Two examples of the method are given which show how oil and gas compositions and properties are calculated with the aid of a computer. INTRODUCTION The calculation of recovery from lean-gas or enriched-gas injection into a saturated or under-saturated reservoir oil requires a knowledge of how phase properties change in a reservoir between injection well and producing well. To determine the phase compositions or properties experimentally would be difficult and time consuming, especially if one wanted to look at the effect of various injection gas compositions. For some fields an engineer would want to make preliminary calculations on the economics of gas injection before he makes the decision to spend a corrsiderable sum of money for laboratory work to obtain the necessary fluid properties. A method for calculatine compositions and properties based on a minimum of laboratory data is described. The minimum amount of data required is injection gas and reservoir oil composition and injection gas solubility as a function of pressure for an undersaturated oil, or the compositions of mixtures of reservoir fluid with two or more enriched gases, which mixtures have a bubble-point pressure that is the same as the expected average displacement pressure. On the other hand, if the economics appear to be attractive, more laboratory data can be obtained in the form of equilibrium constants for three or more mixtures of the reservoir fluid and injection gases. The method is based on the calculation of K's from the equation, log Kp = A + B F, where K is equilibrium constant, p is pressure and F is component characterization factor. This method of plotting K data by means of the above equation is described by Hoffman, Crump and Hocott.1 A and B are constants that vary with a composition parameter. It is shown how experimental data are used to determine how A and B vary with composition. BASIS OF METHOD EQUILIBRIUM CONSTANTS Equilibrium constant (K) data are required for this method. The K of each component is obtained from an equation that gives the product of K and pressure as a function of component characterization factor. The characterization factor F = b(l/Tb — l/T), where b is a constant characteristic of a given component, Tb is the boiling point in OR at atmospheric pressure of the given component, and T is the temperature of the system in OR. This method of plotting K data is described by Hoffman, Crump and Hocott.l The straight-line equation of the log Kp - F plot is log hp = log Kop +BFi, where Kop is at F =0, i designates the component, and B is the slope of the line. The factor F can be

Jan 1, 1966

By Norman B. Braly

The following is not offered as an extended paper on the subject of shaft sinking, but more as a description of the present practice of shaft sinking in the Butte district. The Anaconda company is sinking at present the following shafts: Badger State, Moose, Mountain Consolidated, Mountain View, Pennsylvania and Tropic. At the High Ore and Leonard mines the shafts are being deepened by sinking two compartments and will subsequently be enlarged to the full working size by raising alongside the compartments which are now being sunk. The following other companies are also sinking shafts: Butte-Alex Scott, Butte and Zenith City, Boston and Corbin, North Butte Mining Co. (at the Granite Mountain shaft), East Butte Co. (at the Pittsmont shaft), and the Rainbow Lode Development Co. Shaft Timbering. The shafts of the Butte district, generally speaking, are of three compartments arranged in a straight line, and the pump compartment is usually arranged for the use of an auxiliary hoisting cage, as well as for carrying pipe lines and electric wires. The Rainbow shaft is practically square, and of three compartments. The length of the shafts outside of timber will vary from 17 to 22 ft., and the width from 6 ft. 6 in. to 7 ft. Fir timber is used in all shaft work. This may be obtained from the Coast, when it is known as Coast fir, or from Idaho or Montana, when it is known as native fir. The native fir seems to be the tougher wood, but it is hard to obtain clear lumber in the lengths and sizes necessary for shaft work. Some of the shaft timber of the Anaconda company has been treated with creosote as a preservative, but this practice has not come into general use, as the ground of the camp is so heavy that the timbers usually crush before they rot. The size of timber most used for shaft work is 12 by 12 in., while 10 by 12 in., 10 by 14 in. and 12 by 14 in. are used for some of the special pieces around the shaft. The new Leonard shaft is timbered with 14 by 14 in. wall plates throughout.

Jan 1, 1914

By E. D. Fields, R. W. Sayers, M. C. Tippett

The Duval Corp. porphyry copper deposits at Copper Canyon and Copper Basin, though widely separated, form an econornic unit requiring integrated exploitation. Contrasts in mineralization, host rocks, and mode of occurrence present unique mining and milling problems. Mixed oxide-sulfide ore is treated in extensive dump leaching facilities in both areas. Complex Cu-Au-Ag ore is treated in a 4000-tpd mill at Copper Canyon. In both areas, hypogene metallization occurs within large aureoles of metamoiphism and hydrothennal alteration related to quartz monzonite intrusions of mid-Tertiary age. Supergene processes fitrther altered the rocks and enriched the hypogene protore. At Copper Canyon, hypogene copper and iron sulfides with gold and silver occur in fractures, as partial replacement of favorable beds, and as disseminations in Paleozoic sedimentary rocks. The lower part of the Pennsylvanian Battle formation was a particularly favorable host. Metallization occurs to a lesser extent in quartz monzonite. Metal zoning is well-developed. The deposits at Copper Basin consist principally of supergene copper minerals in arenites of the Cambrian Harmony formation. Oxidation of hypogene copper and iron sulfides in tactite zones has formed at least two commercial deposits; intersections of fractures with favorable beds exerted important ore controls. Recently, the Copper Canyon and Copper Basin properties of Duval Corp. have been added to the list of porphyry copper mines in Nevada, marking the first new copper open pit in this state in 15 years. The properties are situated in the Battle Mountain

Jan 1, 1970

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By Walter Herd

FOR the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S.. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method wasp employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining No. 2 Seam, Springhill, at depth, and records the conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929

By C. R. Ince

THE term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalcopyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggart1 has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls .dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This-is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 lb. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 lb. per ton were added to the thickened pulp and the whole

Jan 1, 1929

By Guillermo Zuloaga

The iron deposits of the Imataca Range of Venezuela, which occur along the Orinoco River, in the northern border of the Guayana Highlands, have lately attracted attention on account of their economic possibilities. Many deposits occur in this area; some of slight economic importance and others that may rank with the largest masses of high-grade iron ore of the world. The geology and the character of the ores seem to be remarkably similar to those of the large iron deposits of Brazil. In the investigation of the Venezuelan deposits a definite relationship has been found between the mineralization of the large orebodies and igneous intrusions, especially norites and granites. The following paper is the result of a field and laboratory investigation of the ore deposits. The field work was done during the months of February and March of the year 1929, partly in the company of Prof. W. H. Newhouse. The laboratory studies have been made in the Massachusetts Institute of Technology, under the supervision of Professor Lindgren and Professor Newhouse. GENERAL GEOLOGY OF GUAYANA HIGHLANDS General Geography and Physiography The Sierra de Imataca proper occupies a narrow belt along the south bank of the Orinoco River, in the northeastern part of the State of Bolivar and in the western part of the Delta Amacuro Territory of Venezuela. The State of Bolivar is generally known as the Venezuelan Guayana, as it forms part of the same physiographic province of the Guianas and northeast Brazil. In general the Venezuelan Guayana is an extensive plateau, sloping gently towards the Orinoco River to the north and towards the Atlantic Ocean to the east. In the northern part mountains are rare, and consist mainly of elongated low hills. Towards the British Guiana-Brazil boundary, table mountains with vertical cliffs are found forming the ranges of Parima, Roraima and Pacaraima. General Geology The Guayana Highlands are the northern extension of the Brazilian Archean shield. Only a few scattered masses of sediments remain on its

Jan 1, 1935