Search Documents

By Gilbert E. Doan, William C. Schulte

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By J. A. Younkins, J. A. Brooke

In 1931 the Philadelphia Company acquired by lease several coal mines in southern Greene County, Pennsylvania. These mines were known as the "Dora," "Seventh Pool" and "Rosedale" mines in the Sewickley seam, and the "Rosemary," "Seventh Pool" and "Warwick" mines in the Pittsburgh seam. All these mines are in the immediate vicinity of Greensboro, Pa., with considerable river frontage on both sides of that village. The mines in each seam are contiguous and to some extent the properties in the two seams lie one above the other. In 1938 the property known as the "Sandy Run mine," in the Sewickley seam, adjoining the Dora mine, was purchased from the Fredericktown Coal and Coke Co. Altogether, by purchase and lease, the company gained control of approximately 3400 acres of coal land in Greene County, from which it was estimated that some 20,000,000 tons of coal could be extracted. Geology of Warwick Properties Both seams of coal outcrop along or near the river on both sides of the town of Greensbgro. They lie on the eastern slope of the Lambert syncline, near the southern end of the axis, consequently the predominant dip of the seams is away from the river, so that development for river handling has the unavoidable disadvantage of adverse grades for haulage to the outside. Predominant grades away from the river at right angles to the "butt" cleat of the coal average about 2.25 per cent dipping in a westerly direction, but local dips occur, which are considerably greater. Predominant grades parallel to the river and at right angles to the "face" cleat of the coal average about one per cent dipping in a northerly direction. Both seams of coal lie in the Monongahela formation, the Pittsburgh bed being the bottom measure of the formation and the Sewickley bed lying about 90 it. above. Approximately midway between the two lies the Redstone coal bed, which is generally thin and of erratic occurrence and therefore of little commercial value. It is mined only locally where it attains sufficient thickness. Sewickley Bed The Sewickley bed is commonly called the "five-foot" or Mapletown" seam, because in Pennsylvania it reaches its greatest thickness and has been mined most extensively in the vicinity of the village of illapletown, approximately one mile west of Greensboro. In the early development of the Warwick properties, which occurred near the river, the seam had an average of 5 it. 2 in. in height. As development proceeded away from the river, however, the height gradually decreased until the average height of the present workings is about 4 ft. 6 in. Present development is encountering lower coal

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By Anson Hayes, John Chipman

THE quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the British Iron and Steel Institute.1 From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. GENERAL THEORY OF SEGREGATION The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1938

By R. W. Fountain, J. Chipman

THE solubility of nitrogen in iron and steel has been of considerable interest due to the role of nitrogen in strain-aging and in quench-aging. It is generally considered that quench-aging is the result of precipitation of carbide and nitride particles from supersaturated solid solution, while strain-aging results from the segregation of carbon and nitrogen atoms to dislocations.1-9 The rate of strain-aging is controlled primarily by the amount of carbon and nitrogen in solution and the temperature. In experiments on strain-aging of pure iron with only carbon or nitrogen as impurities, Fast" has shown that even after 40 hr at 50°C carbon did not give any strain-aging while

Jan 1, 1959

By S. J. Kidder, G. C. McCartney

THE Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies-i.e., the oxide ores of the Old Helen and the siderite of the New Helen-are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source.

Jan 1, 1946

By J. P. Matoney, E. J. Sandy, D. A. Dahlstorm

INTRODUCTION Before an understandable discussion concerning coal-dewatering processes can be initiated, it is necessary to define some terms of usage. The many different meanings and interpretations of terms preclude development of standard definitions so that the terms which are defined in this chapter should be regarded mainly as working terms intended to facilitate communication. A coal slurry ' might be defined as a watery suspension carrying particles of fine coal and other assorted material ranging upward in size from the finest clay particles. Some particles may be in the colloidal sue range and exhibit characteristics of suspended colloids. The dilution of the system generally is such that it is in a condition of independent particle subsidence. In some coal mining areas a slurry is regarded as a suspension of fine coal and other materials having a dilution that cannot be economically dewatered by filtration. A coal slime may be regarded as a slurry containing particles of such size range that 50 per cent or more (by weight) will pass a 200-mesh sieve. Slime suspensions generally are difficult to handle without special treatment in conventional sedimentation equipment. A coal sludge is defined as a slurry that has been partly dewatered by sedimentation usually to a thick or viscous consistency where further dewatering can be most readily facilitated by filtration. Culm and silt are terms characteristic of coal-preparation practice which should be defined. In anthracite terminology, culm is the generally coarse residue or waste accumulation of coal, bone and rock from preparation plants most of which are no longer functional. Culm has a wide range of sizes, some rather coarse, and except to differentiate it from silt, the term is of limited interest in this discussion. In anthracite terminology, silt is the accumulation of waste fine coal, bone and slate settled out from preparation plant water in excavated basins. Silt is generally made up of particles ranging in size from 3/32-in. round-opening screen to the very finest sues. Silt is also referred to at times as sludge, fines, slush, and mud and is the partly dewatered derivative of what has been previously defined as slurry. In the terminology of the bituminous coal producing areas, the word culm commonly corresponds to slurry or slime, depending upon the size distribution of the suspended solids. Editor's Note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections authored by each individual as is the case in most chapters of this book.

Jan 1, 1968

By Arthur Crowfoot

INTRODUCTION The principal object of this paper is to present data on the development of the revolving convex round table as a concentrator for the through 0.07-mm. slimes from the ores of the Butte district, although same brief notes on the earliest recorded use of this type of concentrating table in the ore-dressing plants of the Lake Superior region and of the Butte district are also presented. The revolving convex round table belongs to the class of concentrating tables known as film-sizing tables, these tables using the relative transporting power of a film, or thin sheet of water, as it flows over a quiet inclined surface, to separate the minerals of a sorted product.

Jan 8, 1914

By R. E. Barnes

An overall view of the perlite industry is concisely presented. The geology, mining, milling, processing, and applications of perlite, as well as the present status of the perlite industry are treated. Perlite, in strict petrological usage, describes a specific variety of volcanic glass in which strain, incident to cooling, yielded a concentric structure of fracturing which may be visible either to the naked eye or under a microscope. In commercial usage, the term perlite includes any naturally occurring acidic glass of volcanic origin that will expand when heated to a suitable temperature. The name perlite is a derivation of perlstein which originally defined "certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."1 While perlite has been known to geologists for many years, it was not until 1941, while investigating perlite for use in enamel, that an assayer in Superior, Ariz., noted the unusual expansion characteristics of the ore. Further investigations were delayed until following World War II when many small plants were built and experimentation in the treatment and uses of perlite began. The Perlite Inst. was organized in 1949 to promote the development of the new industry, establish commercial standards through research, and to explore new uses and markets. The Institute, located in New York, represents some 50 producers in the U.S., Canada, Australia, England, France, Germany, Greece, Japan, Mexico, and New Zealand. In 1949, 71,l002 short tons of crude perlite were produced, sold or used by U. S. producers, and this figure increased to 325,0003 short tons by 1959. Such a rate of increase indicates the rapid and continuing growth of the perlite industry. GEOLOGY Perlite ore in its crude form has been found in seven of the mountainous western states, since un-devitrified siliceous volcanic rocks are limited to this section of the U. S. Commercially operated perlite deposits are normally of Eocene and Oli-gocene age.4 These deposits are often several hundred feet thick and may extend over hundreds of acres. In 1959, 13 companies in six states produced crude perlite, although the output in New Mexico comprised 79 pct of the total domestic crude output. Other states in order of their production were: Nevada, Arizona, California, Colorado, and Utah.5 Foreign deposits of perlite which are either producing or under exploration are Australia, Canada, Greece, Hungary,6 Iceland, Ireland, Japan, Mexico, New Zealand, and Sardinia. The ore may exhibit a variety of characteristics depending partially on its water content and eruption history and may range through many shades from black to white. While these characteristics may vary slightly among deposits, perlite ore from a particular source is normally quite uniform. Available chemical analyses of perlites from a large sampling of domestic deposits were recently assembled by the Technical Committee of Perlite Institute and are presented in Table I. While the ranges given do not apply to a particular perlite, they are an indication of the chemical analysis which may be expected from any presently commercially operated deposit. The specific gravity of the perlite ore ranges between 2.2 and 2.4, and its bulk density when crushed and sized is 75 to 90 Ib per cu ft. MINING AND MILLING Perlite ore is quarried from open pits by conventional power equipment, although blasting has been occasionally employed. The rock is then stock-piled until needed. While the milling of perlite may seem a simple process compared to that required for basic metals, or even other nonmetals, the need for accurate control of particle size becomes extremely important in further processing. The first step in this operation is the primary crusher, which is normally a jaw crusher. Following crushing, the material is dried, if necessary, in a rotary dryer and conveyed to a secondary grinder which may be a rod mill, hammer-mill, or cone crusher. However, the crushing characteristics of the perlite, caused by incipient cooling fractures, requires it be removed from the grinding operation once it is reduced to the required size so as to prevent overgrinding. Following the grinding operations, various size screens are used to separate the ore according to particle sizes required for particular uses. Most plants use two or more stages of crushing with perhaps four stages of screening.

Jan 1, 1961

By William C. Schulte, Gilbert E. Doan

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By H. J. Rose, J. J. S. Sebastian

When coal is stored under ordinary conditions, progressive changes take place in its chemical and physical properties. These changes are largely caused by the reaction of atmospheric oxygen with the coal substance. Although this "oxidation" or "weathering" occurs slowly in the case of high-rank coals, it is nevertheless a matter of considerable importance, since even a small amount of oxidation may affect the value of coal for carbonization purposes. Coal storage is a necessity at all carbonizing plants. In normal times there are about 5,000,000 tons in storage at by-product coke ovens and gas retorts in the United States, as compared with an annual throughput of about 75,000,000 tons. In other words, the average coal reserve at such plants is slightly less than one month's supply. However, owing to the cost of storage and recovery, coal is usually left in stockpile for as long a time as the management thinks advisable. Storage for six to eight months is common practice and is, in fact, a necessity at certain plants which obtain their coal by water routes that are closed during winter months. Modern by-product coke ovens operate continuously, and they are not cooled down from the time that they arc put into operation until they are shut down for rebuilding—perhaps 20 years later. This continuous operation is imposed by silica-brick construction and high operating temperatures. It is therefore obvious that coke plants must at all times maintain an adequate supply of stored coal, in order to prevent a failure in supply from any cause whatever. Thus when strikes or other emergencies threaten, abnormally large coal stocks are accumulated and held at coke and gas plants. Many of these plants have been forced, at some time or other, to use coal that has been stored for several years. Such coal may fail to coke at all, or it may produce a dirty appearing, weak coke of reduced value. The yields of salable by-products may also be distinctly lowered. However, it must not be assumed that slight oxidation or heat effects are always injurious. Certain high-volatile coals produce a stronger, blockier

Jan 1, 1930

By Francis O. Blackwell

There are few industries in which power is more important to successful operation than mining, and none in which it is so difficult to ohtain power cheaply. Fuel is usually expeusive in mining districts, ana the ma chinery may be widely scattered and located in places difficult of access. The work is often so intermittent and variable as to prevent the economical use of steam. Mining operations are likely to exhibit accumulations of comparatively small and inefficient engines, numerous boilers and long lines of wasteful steam-pipes. Conlpressed air, as a means of transmitting power, is so handicapped by losses in the compressors and piping that it is limited to short distances and to the operation of apparatus requiring power, without regard to cost. To-day, electricity is rapidly replacing other methods of power-distribution, primarily because it is practically independent of distance. By selecting a potential proportional to the length of transmission, the cost of electric conductors and the e5ciency are the same for all distances within reasonable limits. For instance, a given amount of power can be delivered either 528 ft. away at 100 volts, or 50 miles at 50,000 volts, with the same total of copper per H.P. and with exactly the same loss of power in the transmissioo-circuk. This independence of distance permits the selection of the place most advantageous for power-development as a site for an electric power-plant, and the co~~centration there of the generation of all the power required within a radius of many miles. The powel.-site may be at a fall of water, if one is available, or a steam-plant can be built where fuel and supplies are cheapest, or where suflicient water is available for boiler-feed and condensing purposes.

Jan 1, 1904

By A. L. Titchener, M. B. Bever

The stored energy of cold work was investigated in drawn gold-silver wires by tin-solution calorimetry as a function of strain, strain rate, initial grain size, and temperature of defornation. The energy expended in the deformation process was measured. Hardness was also measured and was correlated with the stored energy as a function of strain and strain rate. Mechanisms of energy storage are discussed. THE variables which determine the amount of energy stored in a metal during cold work are of two kinds: those involving the metal and its condition and those involving the process of deformation. For example, the stored energy differs between one metal and another and between different degrees of purity of a single metal. It also depends on the nature of the deformation process and particularly the extent, rate, and temperature of deformation. Most investigators have reported the stored energy as a function of strain (or some similar geometric parameter) or of the energy expended during deformation. In general the stored energy increases with strain, rapidly at first, but more slowly at large strains until a saturation level is reached. Information about the effects of other variables, however, is limited. Some data are available on the dependence of the stored energy on the purity of a metal1 and on the composition of

Jan 1, 1960

By John F. Elliott, John R. Rawling

The rate of reduction of silica to silicon by carbon at 1550° to 1700°C in iron blast-furnace type slag-metal systems has been investigated. In the tower portion of the temperature range oxygen transport in the metal boundary layer at the slag-tal interface is probably rate limiting. A second step, which apparently involves a chemical process in the slag at the slag-metal interface, appears to be rate limiting when the oxygen-transport limitation is avoided. Above 1650°C rate control of the reduction by carbon probably is mixed between the two steps. INVESTIGATIONS1.2 into the equilibrium distribution of silicon between graphite-saturated slags and metals typical of iron blast-furnace practice show that, under the experimental conditions specified, the reduction of silica to silicon is relatively slow compared with the rates of other slag-metal reactions under similar conditions. For this reason, the reduction of silica in blast-furnace slag-metal systems was considered to be an interesting subject for further study. Investigations of the kinetics of the reaction3-5 suggest that several possible steps may be rate controlling, and that the rate-controlling step depends not only on the physical state of the systems but also on the configuration of the apparatus. The main objects of the investigation reported here were to sug- gest plausible reaction paths for the reduction of silica under the experimental conditions chosen and to determine the step or steps which control the rate of reduction of silica. EXPERIMENTAL Two types of experiments involving the reduction of silica from the slag were carried out. In the first, the only reducing agent present was carbon (graphite), for which the over-all reaction is (SiO2) +2C(gr) —Si + 2Co(g) [l] The second type was a graphite-saturated ferro-silicon-iron concentration cell. In it silica in the slag could be reduced either by carbon according to Eq. [I], or by a reaction of electrochemical nature in which silicon was oxidized at the ferrosilicon-slag interface and silica was reduced at the slag-iron interface without the formation of CO. The two types of experiment are described below. Reduction of Silica with Carbon as the Only Available Reducing Agent. The reduction of silica was accomplished by allowing a liquid lime-alumina-silica slag and graphite-saturated iron to react in an induction-heated graphite crucible. The crucible was 2.25 in. diameter and 5 in. deep; it was fitted with a graphite stirrer which penetrated through the slag and into the metal, Fig. 1. The slag and metal charges weighed 350 g each. Pure carbon monoxide at a pressure of 1 atm was maintained above the melt by passing the purified gas through the crucible at a rate of 0.5 liter per min. The gas did not stir either the slag or metal. Temperature measurements were made by sighting an optical pyrometer down the hollow stirrer rod into a 1/4-in. hole drilled in the stirrer blade. The crucible temperature was maintained within *15"C of the required value by manual control of the power supply to the

Jan 1, 1965

By Harold W. Aldrich, Walter G. Scott

The leaching process of the Inspiration Consolidated Copper Co. is based upon the solubility of oxidized copper in sulfuric acid and the solubility of sulfide copper, largely in the form of chalcocite, in ferric sulfate solution. This necessitates the carrying of a rather large amount of iron in solution. The ferric sulfate is regenerated from ferrous sulfate by the oxygen given off at the anode during electrolytic precipitation of the copper. In September, 1924, excavation was started at Inspiration, Arizona, for the construction of a plant to treat 7500 tons of ore per day. When the plant was begun, the fact developed that by a minor change in the height of the overflow on the leaching tanks, 9000 tons could be charged into each tank and treated satisfactorily. This determined the maximum capacity of the plant as 9000 tons per day. The first ore was charged in October, 1926, and there are now available the records of five complete years of operation; namely, 1927 to 1931, inclusive. The original estimate of copper content of the ore to be mined for this plant was 1.19 per cent, of which 0.77 per cent was as oxide and 0.42 per cent as sulfide. From the metallurgical results obtained at the 35-ton pilot plant, it was estimated that a 90.0 per cent extraction of the oxide copper and a 75.0 per cent extraction of the sulfide copper could be made. It was estimated that the tailing would carry 0.182 per cent total copper, resulting in a

Jan 1, 1934

By J. A. Younkins, J. A. Brooke

In 1931 the Philadelphia Company acquired by lease several coal mines in southern Greene County, Pennsylvania. These mines were known as the "Dora," "Seventh Pool" and "Rosedale" mines in the Sewickley seam, and the "Rosemary," "Seventh Pool" and "Warwick" mines in the Pittsburgh seam. All these mines are in the immediate vicinity of Greensboro, Pa., with considerable river frontage on both sides of that village. The mines in each seam are contiguous and to some extent the properties in the two seams lie one above the other. In 1938 the property known as the "Sandy Run mine," in the Sewickley seam, adjoining the Dora mine, was purchased from the Fredericktown Coal and Coke Co. Altogether, by purchase and lease, the company gained control of approximately 3400 acres of coal land in Greene County, from which it was estimated that some 20,000,000 tons of coal could be extracted. Geology of Warwick Properties Both seams of coal outcrop along or near the river on both sides of the town of Greensbgro. They lie on the eastern slope of the Lambert syncline, near the southern end of the axis, consequently the predominant dip of the seams is away from the river, so that development for river handling has the unavoidable disadvantage of adverse grades for haulage to the outside. Predominant grades away from the river at right angles to the "butt" cleat of the coal average about 2.25 per cent dipping in a westerly direction, but local dips occur, which are considerably greater. Predominant grades parallel to the river and at right angles to the "face" cleat of the coal average about one per cent dipping in a northerly direction. Both seams of coal lie in the Monongahela formation, the Pittsburgh bed being the bottom measure of the formation and the Sewickley bed lying about 90 it. above. Approximately midway between the two lies the Redstone coal bed, which is generally thin and of erratic occurrence and therefore of little commercial value. It is mined only locally where it attains sufficient thickness. Sewickley Bed The Sewickley bed is commonly called the "five-foot" or Mapletown" seam, because in Pennsylvania it reaches its greatest thickness and has been mined most extensively in the vicinity of the village of illapletown, approximately one mile west of Greensboro. In the early development of the Warwick properties, which occurred near the river, the seam had an average of 5 it. 2 in. in height. As development proceeded away from the river, however, the height gradually decreased until the average height of the present workings is about 4 ft. 6 in. Present development is encountering lower coal

Jan 1, 1947

By John S. Johnson

The maintenance cost, or renewal cost, in any preparation plant is a large item of expense and reflects in the total cost of producing and preparing the ton of coal. It is given constant study to the end that ways and means of controlling and reducing this proportion of the total cost may be developed. Study of this item of cost has proceeded along usual lines, which are: proper functioning of the maintenance organization; systematic and thorough inspection to prevent breakdonns; the making of repairs before renewals are needed; maintenance work done thoroughly the first time, instead of patching, study of parts needing frequent renewal or repairs or conditions resulting in delays, thorough knowledge of cost by the mall responsible for maintenance; and the use of special equipment and materials. This paper is to deal with special equipment and materials to reduce the maintenance cost hut before going into that I want to express an opinion on the general subject. Maintenance Organization Usually maintenance is taken care of by a group of men who perform their work on the off shift. The work is arranged by the operating official who should be thoroughly familiar with maintenance, so that materials needed may be made up for the particular job and waste of time in looking up materials be prevented. To perfect the maintenance organization, all operating attendants should be thoroughly trained to be familiar with all working parts of their equipment, to make a thorough inspection and to write out the slip for the work required. This requires job analysis, but it is worth the effort, because the attendant usually is better informed than anyone else about his particular equipment. The operating official can judge the scope of the work to direct the repair and to have material ready. Lubrication is an important item in maintenance, and a subject by itself. Usually the breaker oiler is designated to perform this task. This man should be picked for his ability and put in line for promotion to machinist. He should be trained as an inspector, as he is constantly visiting most parts of the breaker and has an opportunity to observe needed maintenance. The first thing is to lay out maintenance work and arrange to have it done; the next is to check the work and see that it has been properly done. This check should be made by the operating official, and through the attendant. The cost statement showing the various items of maintenance cost is not often understood by the man in direct charge. Cost sheets should be simplified and worked up by breaker sections; e.g., the cost of

Jan 1, 1947

By Maurice Ewing, A. P. Craby, J. W. Peoples, J. A. Peoples

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected 'his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By C. Schlumberger

SINCE the beginning of .the year 1928 the senior authors and their associates have applied a series of procedures which makes possible the detailed study in situ of the formations traversed by a drill hole before the casing has been landed. They have given the name "electrical coring" to the ensemble of these processes, which now replace in a large measure the mechanical coring performed by the drillers, and permit the gathering of bottom-hole data hitherto unobtainable. Three years have elapsed since the technique and interpretation of these measurements emerged from the experimental stage and entered the field of industrial application on a large scale. The total length of drill holes so far surveyed by the authors and their associates, all over the world, amounts to several millions of feet. Practical and strongly built equipment has been evolved, which permits the examination in a short time of an open hole several thousand feet long. No comprehensive paper has yet been published discussing the essential principles of the processes applied and bringing into evidence their economic interest. This is the object of the present paper.1 Numerous examples of field work performed under varied geological conditions are given, constituting a concrete illustration of the services rendered by the new methods. The study in situ of the formations penetrated by a drill hole is based on the measurement of a given physical factor or parameter associated with these formations. Generally. the measurements are made syste-matically along the whole length of the open hole. The physical factors or parameters which are now utilized by us to this end are: (1) the resistivities of the rocks; (2) their porosity; (3) their electrical anisotropy; (4) their temperature; (5) the resistivity of the muds. In order to

Jan 1, 1932

By A. H. Geisler, R. F. Mehl, C. S. Barrett

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943