Search Documents

By Goodman, Richard E.

A complete rational analysis for design of excavation slopes and loaded rock masses is a desirable but perhaps unattainable goal. Irregular external and internal boundary conditions, poor understanding of failure criteria for large masses of rock, capricious material properties, and the importance of indeterminate forces and inaccessible and virtually un- sampleable rock defects emphasize the importance of experience in this aspect of rock engineering. The experience must be correlated with geological factors. In certain regions the accumulation of such experience through the observation of existing rock slopes in various formations constitutes an important aspect of studies for design of rock excavations.

Jan 1, 1969

By Henry F. Herley

The New Orient mine, owned and operated by the Chicago, Wilmington & Franklin Coal Co., has caused a great deal of comment and interest because of its unusual features and huge daily production. It is in Franklin County, Illinois, adjacent to the town of West Frankfort. The seam being mined is the Illinois No. 6 which in this locality is 9 to 12 ft. thick and lies approximately 500 ft. below the surface. Without fear of contradiction, it can be said that this is one of the largest coal mines in the world from a daily production standpoint. During 1928, New Orient produced 2,400,000 tons, which amounts to over 10,000 tons each day the mine operated that year. The mine is built for a capacity of 12,000 tons but has actually hoisted over 15,000 tons in one 8-hr, shift. This enormous production can perhaps be better visualized if it is realized that each day's operation depletes over two acres of coal. The general features of this mine have already been fully covered in a paper by George B. Harrington,' President of the Chicago, Wilmington & Franklin Coal Co. In a paper of the nature of Mr. Harrington's, it was unnecessary to stress any particular phase of mining conditions, consequently the ventilation problems were touched upon but lightly. In this paper an attempt has been made to describe some of the problems which have been encountered in providing adequate ventilation for the mine. Ventilating Conditions The acreage allotted to New Orient mine has a length, north and south, of approximately 6 miles, and a width, east and west, of 2 to 4 miles. A number of important considerations caused the hoist shaft, air shaft and surface plant to be located near the southeast corner of the property, instead of near the center, as is usual. During the initial phase of the mine development, the mine was ventilated through these shafts, although there was a full realization that at some future date other shafts would be required.

Jan 1, 1930

By Leo J. Vogel, E. D. Hummer, David J. Akers

INTRODUCTION An efficient refuse-disposal system is a necessary part of the modem cleaning plant. The large-scale refuse system and disposal area, engineered for the lifetime of the plant, has become more important due to the greater tonnages of refuse produced from increased quantities of mechanically mined and prepared coal. Laws and increased government regulations have affected the design and operation of disposal systems. THE EFFECT OF MINE AND PLANT OPERATION Refuse disposal starts at the mining face. The mining system, the type of roof support, the machinery used, and the degree of discipline at the face contribute to the amount and type of refuse that must be removed through the disposal system. Economies gained through modification of the mining system or mining machinery may be partially offset by increased dilution of the mined coal with impurities from associated rock formations. In some cases the change in the mining system and equipment has reduced the dilution. In all cases the ratio of impurities that must be removed from the raw-coal feed to the plant not only affects the maintenance and

Jan 1, 1979

By Thomas A. Simpson, Tunstall R. Gray

The Birmingham district first produced steel from Alabama hematite ores in 1899. Since then, the district generally produced more than 6.0 million gross tons of ore a year to the late 1950's. Production has declined since then to an annual rate of about 1.5 million gross tons. Reserves calculated for the district are sufficient to last many years. Mining in the district is now confined to Woodward Iron Company's Vance and Pyne mines. The rocks exposed consist of about 15,000 feet of consolidated Paleozoic sediments with a thin veneer of unconsolidated Cretaceous sediments in the Vance area. The district is characterized by a distinctively parallel and subparallel, slightly arcuate series of faults and joint systems. In view of available information, it seems reasonable to conclude that the Birmingham red ores are of sedimentary origin, modified to a small extent by diagenetic replacement after original deposition.

Jan 1, 1968

By Eugene McAuliffe

THE last obtainable figures of the value of the coal mining investment are those contained in the U. S. Census Reports, from data gathered in 1919. The values shown therein and set forth below cover lands and equipment and do not include distribution and marketing facilities. The working capital necessary to meet pay rolls to purchase material and supplies and workmen's compensation insurance are likewise excluded.

Jan 1, 1926

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By Max Hebgen

Within the State of Montana the streams rise in the high mountains at. an elevation of from 5,000 to 8,000 ft. These streams leave the State line both east and west at elevations from 3,500 to 2,400 ft. It is, therefore, apparent. that all these streams have an average fall of 3,000 ft. within the confines of the. State, and many opportunities are presented on all streams. for the development of power, by taking advantage of the natural fall. It is probable that 1,000,000 h. p. can :be developed in the State of Montana. I. NATURAL FEATURES OF STATE AFFECTING POWER DEVELOPMENT. The main. range of the Rocky mountains, forming the Continental Divide, cuts the State of Montana into two parts. The eastern part is drained by the Missouri river and its tributaries, the Madison; Jefferson, Gallatin and Yellowstone, rivers. The western part is drained by tributaries to the Columbia river, the Clarks fork and the Kootenai river. The Clarks fork in turn is formed by the junction of Missoula and Flathead rivers, the latter, draining Flathead lake. The western part of the State. is mountainous and the eastern part is comparatively level. As a natural result the rivers in the western part are capable of generating large amounts of power, while in the eastern part of the State natural power sites are much fewer and farther apart. It also follows that in the mountainous districts large amounts of power are required for the mining industry, while in the eastern part of the State, which is principally devoted to agriculture, power is required in smaller quantities. ?

Jan 8, 1913

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950

By AIME AIME

THE graduating class whom I am particularly addressing are going into the world at least a month earlier than normal, because of the war. You have been free to choose your work. You have chosen to be mining engineers. The principal importance of your engineering education to date has been in teaching you how to think and how through books to have ready access to the accumulated experience of previous generations, as well as the current experience of the day. You should by now have acquired something of the engineering point of view, the open skeptical mind. the power to observe, experiment, and draw conclusions, form theories and test these by further experiment, and weigh the inherent probability of conclusions drawn by others. I am asking you today to consider certain facts and the conclusions I am drawing from those facts.

Jan 1, 1942

By FOSTER HEWElT

THE scope of this paper is the description of two districts in Peru in which deposits of vanadium have been found, and the consideration of much laboratory-work that I and others have done to determine the nature of these deposits. It is with regret that I present some of the data in a state of evident incompletion, particularly the analyses of a few of the minerals, which leaves some doubt as to whether the true nature of the minerals is understood. I make no apology, however, since in this case, as in many others referring to ore-deposits, conclusive opinions cannot be stated until a great amount of work has been done, and the deposit has been thoroughly exploited. I believe that the data and the tentative conclusions here presented indicate a unique and interesting condition which may assist others in work along similar lines; and further, what is of more practical importance, stimulate a search for a metal which, though long considered rare, is probably so merely because proper care has not been taken to recognize it. An excellent bibliography on the occurrence of vanadium in nature is given by F. W. Clarke in his paper, Data of Geo-chemistry;1 and in the preparation of this paper I have consulted many of the references contained in the Bibliography of the Chemistry of Vanadium, by M. Moissan.2 A brief review of the subject having special reference to the metallurgy of vanadium is contained in the small book by P.. Nicolardot.3 One of these vanadium-deposits has already been briefly

Mar 1, 1909

By Howard R. Pratt, Jimmie L. Bratton

The Air Force Weapons Laboratory (AFWL) has been carrying out a series of experiments whose principal purpose is to measure the dynamic response of rock media to large pressure pulses. Coupled with the field experiments have been theoretical calculations simulating this response. These two approaches allow an appraisal of the current ability to measure in-situ rock response under extreme conditions and also give a fair estimate of the current state-of-the-art in the area of computer calculation of the response of "real" geologic media to a large load. The area chosen for the test series is composed of a sequence of sedimentary units (shale, sandstone, and limestone) located in the Estancia Valley 45 miles east of Albuquerque, N.M. (Fig. 1). The units, which dip gently off the uplifted Manzano Mountains to the west, are essentially horizontal at the test site. An extensive geologic and geophysical investigation of the area was carried out in the form of surface mapping and seismic exploration. Numerous holes were cored and material properties were determined from tests of the cores. In-situ geophysical measure¬ments were also carried out. The experiment consisted of loading a 60X40 ft test area with a 4000-psi transient exponentially decaying pressure pulse. The pulse was initiated at one end and traveled the 60-ft length of the test bed. The test area was instrumented with acceleration, velocity, and strain measuring devices placed in drill holes to depths of 30 ft. Theoretical computer calculations of the response of the layered geologic media have been carried out on the AFWL CDC 6600 using one and

Jan 1, 1972

By Gerald C. Dohm

INTRODUCTION After a mining company has discovered a mineral deposit, the problem is then how to mine and process that deposit the best way. The principal problem facing managers or engineers who must decide on mine plant size, equipment selection, and long-range scheduling is how one can optimize a property not only in terms of efficiency but also as to project duration. Mine opti¬mization is dependent upon the interaction of con¬tributing parameters which leads to maximizing the net present value (NPV) Realistic mine planning is the key, to the analysis. The process is to be used when evaluating undeveloped properties or when a complete revamping of existing facilities is scheduled The proc¬ess is not intended for detailed mine design but rather for property evaluation and feasibility studies. The derivation of the various input parameters will only be discussed to the point where a meaningful correlation can be made with the overall analysis. The interrelationship of the parameters will be the central point because most company guidelines and financial analysts have their own standards when deriving the various inputs. Assume that the data is totally acceptable and pro¬vides at least the following categories of information and guidelines- (1) mineral and waste inventory; (2) geologic, hydrologic, and geotechnical criteria; (3) topographic layout including property boundaries; (4) metallurgical flowsheet, recovery and design criteria; (5) access, water, power, and environmental base-line study; and (6) financial constraints (minimum rate of return, payback period, etc).

Jan 1, 1979

By D. L. Luffel

This paper presents two main developments: (1) a short, constantly accelerated centrifuge method of measuring drainage capillary pressure properties of cores, and (2) a new analytic method of treatment of centrifuge measurements to obtain saturation-capillary pressure relations. Toward the first objective, a clever experimental method is presented which is certainly more rapid than previous centrifuge methods. Toward the second objective, a new analytic method is derived to eliminate the approximate method of Hassler and runner. The derivation of this new analytic method, however, appears to be in error. The new analytic solution is developed as Eq. 5 in Appendix A. At the beginning of this derivation, the average wetting phase saturation of a core is expressed as, where is the centrifuge angular velocity. Eq. D1.2 makes explicit the dependence of S and S upon The second equation shown in Appendix A expresses the relation between the three variables Since for a given porous medium the saturation is uniquely related to capillary pressure, the functional dependence of S upon P is trivial, i.e., Pc.ri does not actually appear. Thus, the function 5 (r, ) may be expressed as a new function, S*, of PC, , alone The author transforms the variable of integration in Eq. Dl through use of Eq. D2 and writes

Jan 1, 1965

By W. A. Hockings, D. W. Fuerstenau, A. L. Mular

This paper briefly describes a simple air pycno-meter and its use for rapid determination of the composition of mixtures of solid particles. Research on such problems as the pelletizing of solids, the mixing of solid particles, and the comminution of mixtures can be simplified by means of this analytical tool. THEORY OF OPERATION Liquid pycnometers1 are commonly employed to measure volumes. These devices are time consuming and sometimes give inconsistent results. The liquid used in the pycnometer may have an undesired influence on the material to be measured; moreover, complete displacement of air by the liquid is seldom

Jan 1, 1963

By John A. Church

Jan 1, 1903

By R. B. Schluter, M. M. Fine

Processes for manufacturing prereduced pellets have heretofore required temperatures of 2100°F or higher. Sulfides will accelerate the liquid-phase sintering of metallic iron, yet do not deter the reduction of iron oxides. The sulfides may be introduced as gases to the kiln atmosphere or as solids in the re-ductants. The net result is that well metallized iron pellets with good crushing strength can now be produced at a little over 1800°F. One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. In May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.' More recently, in November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials at Evian, France, in May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then the current interest in reduction must be at a high level. Barrett,2 one of the early pioneers, stated some years ago that "The history of sponge iron has been so discouraging that many men in the iron and steel industry are violently opposed to giving it any further consideration." In spite of the "violent opposition" noted by Barrett, research people in and out of the industry continue to be attracted by the elusive prospect of uncovering a simple, viable means of direct reduction. Wild,3 one of the speakers at Evian, listed no less than 48 direct reduction processes (laboratory, pilot plant and commercial). Some of these were of historical interest only, but many others had resulted from developments within this decade. The previous big thrust into direct reduction occurred under the artificial impetus of a wartime economy (World War 11) and was largely an effort to provide more melting stock without coke ovens and blast furnaces. The present-day inquiry is proceeding at a more leisurely pace and the emphasis is different. For one thing, there is much less anxiety to circumvent the blast furnace. On the contrary, a whole new research endeavor has grown from the discovery that metallized burdens are exceptionally productive.4 Although the search for a melting stock

Jan 1, 1970

By Herty, C. H.

Present-day interest in the question of "dirty steel" has arisen primarily from the increasingly rigid specifications on various grades of steel and from the growing conviction that non-metallic inclusions are the source of many of the difficulties in meeting these specifications. The importance of inclusions has unquestionably been over-emphasized in many cases, but on the other hand many unpublished instances could be recorded where all evidence pointed to inclusions as the primary cause for the failure of steel in rolling or in service. The solution of the problem of dirty steel is not a matter of a few years. There are almost numberless types of inclusions. They segregate in steel ingots in an entirely different manner from other impurities, and, at best, only a start has been made in developing correct analytical methods for their determination. Most of the writers in the field have expressed opinions rather than given facts, and so many variables enter into the manufacture of steel that a study of plant conditions is difficult unless definite facts on certain phases of the inclusion problem are available. This statement is not intended to convey the idea that little work has been done on this problem. On the other hand, the number of investigations has been large, but in most cases too many variables have been present to allow definite conclusions to be drawn. In the body of the text, reference to previous investigations is made at suitable points. Rather than burden the reader with a lengthy review of the literature on the general subject of inclusions, reference to the particular works pertinent to the subject matter of the bulletin has been discussed. Three excellent bibliographies b on the subject have been lately published: one by the Committee on

Jan 1, 1957

By Arthur B. Foote

THE ball mill has superseded stamps for the reduction of gold ores in most of the recently designed plants, partly because stamps are not suited to die fine grinding required for flotation, and partly to save space and construction cost. Experience with these new mills seems to confirm the idea that it is more difficult to recover bold from a ball-mill product than it is when stamps are used for crushing. Microscopical examination of particles of gold that have passed through a ball mill show that the gold has been pounded into exceedingly thin flakes coated with a talcy surface, making it more difficult to save by amalgamation, flotation, or concentrating. Bearing in mind that gold is extremely malleable, it seems reasonable that this should be so. Contrast the action in a stamp battery, where the crushing is by impact in the presence of mercury, to the grinding and rolling under pressure in a ball mill. It is well known that a better recovery can be obtained by panning or amalgamation from a sample of ore that has been crushed by mortar and pestle than from one reduced on a bucking board.

Jan 1, 1937

By J. J. Fritts, J. L. Patrick, T. L. Wright, C. O. Ensign, W. S. White, J. W. Trammell, J. C. Wright, D. J. Hathaway, R. J. Leone

The copper deposit at White Pine, Michigan, from which a little more than 5 per cent of United States primary copper currently is produced, is a large stratiform orebody, 4 to 25 feet thick and several miles across. The present ore column, containing about 1.2 per cent copper as chalcocite and native copper, is confined to the basal beds of the Nonesuch Shale. This upper Keweenawan (Upper Precambrian) formation is a distinctive gray siltstone unit, about 600 feet thick, overlying and overlain by thick red-bed sequences. All these rocks contain abundant volcanic debris, but the latest known igneous activity within 50 miles antedated the Nonesuch Shale. The rocks are unmetamorphosed and only moderately deformed, mainly by tilting and faults. Pyrite, presumably syngenetic, is the only prominent sulfide throughout most of the Nonesuch Shale. The basal beds of the formation, however, contain disseminated copper minerals instead of pyrite and constitute the cupriferous zone. On a regional scale, the top of the cupriferous zone cuts across bedding, and ranges from an inch or so above the base of the formation in some areas to more than 50 feet in others. However, within the cupriferous zone the distribution of copper shows remarkable stratigraphic control. Certain beds are copper-rich compared to the beds that lie between them and the differences persist throughout the White Pine region. Several darkgray thinly laminated beds in the lower 10 to 25 feet of the Nonesuch Shale are rich enough and sufficiently close enough together to constitute a mineable thickness where they lie within the cupriferous zone. Pyrite is the characteristic sulfide of the Nonesuch Shale as a whole. The principal sulfide mineral of the cupriferous zone at the base of the formation is chalcocite. The succession of minerals outward and upward from the center of the cupriferous zone is native copper-chalcocite-bornite-chalcopyrite- pyrite. The bornite and chalcopyrite are confined to a narrow fringe at the margin of the cupriferous zone. This pattern of mineral zones is believed to represent reaction between syngenetic pyrite and introduced copper. The main copper mineralization is independent of structure and apparently antedates deformation. Details of the geometry of the cupriferous zone indicate the possibility that copper was introduced from the underlying sandstone prior to lithification. The source of the mineralizing solutions and their copper is not known.

Jan 1, 1968

Aamot, Olav Crone, (M'29) Chem. Engr., Elektro¬kcmisk, Raadhusgt. 32, Oslo. Norway. . Aase. Glenn D., (J'40) Jr. Met., American Smelt. & Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engrg., Avenal, Calif. Abadilla, Quirico A., (M'38) Min. Engr., Dir., Bureau of Mines, Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch. Morenci. Ariz. Abbott, Clarence E., (M'04) Civ. Engr. V.P., Tennessee Coal Iron & R.R. Co., 1542. Brown Mars Bldg. Birmingham. Ala. Abel, Raymond L.. (M'23) Chem. Engr., Com¬manding Officer, Pittsburgh Chem. Warfare urement Dist., American Bank Bldg.. Pittsburgh. Pa. Abel, Walter D., (M'32) Min. Engr., Supvr. Engr.. R.F.C., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur. Ga. Abell, Leo M.: (M'31) Mill Supt. & Met.. Em¬ peror Gold Min. Co., Ltd., Vatukoula. Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Fan. Abernathy, Jack H., (M'40) Cons. Petr. Engr., First National Bldg.. Oklahoma City, Okla.

Jan 1, 1943