Search Documents

THERE can be little doubt in the mind of anyone of the great interest which has been provoked in the mining and petroleum industry by the com-paratively new geophysical methods of prospecting, after the sessions at this year's meeting of the Institute. Not only were the sessions very well attended but every¬one seemed most attentive. Although the discussion was somewhat limited in general, that may well be at-tributed to the newness of the subject. Two sessions on this subject were planned originally, but these gave insufficient time for the presentation of all the papers prepared and a third session was abso-lutely necessary. The first meeting dealt entirely with the gravity methods and was completed in the scheduled time owing to the fact that but two of the five papers listed were read. The second session was devoted to magnetic and electrical methods, the completion of which had to be carried over into the third period of geophysics. The first session on geophysical prospecting, and in-cidentally the first scheduled Institute meeting devoted entirely to this subject, was most appropriately opened by E. L. DeGolyer, the chairman of the session. It was through the efforts of Mr. DeGolyer that the first gravity work, as applied to prospecting, was under-taken in this country. Again most appropriately, the first paper presented was given by Donald C. Barton, who carried on the first work with the Eötvös torsion balance in America and aided materially in its development. A subject, the theory of which is so difficult to understand as it is generally presented, was so clearly illustrated and ex-plained by the speaker that even a novice could grasp the fundamentals. Dr. Barton, in showing actual re-sults obtained in torsion balance surveys with the in-terpretation of the sane and later drilling records, was free in stating that there are many limitations to the field in which this and the other geophysical instruments may be successfully employed. This paper called for considerable discussion relative to the application of the torsion balance to gravity surveys over various types of structures. During the course of this discus-sion a very important point was emphasized by the chairman, namely, that for successful application of any or all of the scientific methods of prospecting, a back-ground of experience is absolutely necessary to serve as a basis for further work. This can only be secured by contributions from the results of actual prospecting work.

Jan 3, 1928

By E. A. Gulbransen, J. W. Hickman

IN a previous paper1 the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300° to 700°C. except for copper, where the range selected was 100° to 500°C. The results of these studies were presented in graphical form as existence diagram, of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviations in lattice parameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: I The existence diagrams of various alloys. [2.] The effect of the structure of the [ying] metal on the existence diagram of Iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body- centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K42B1 Nichrome V, Hipernik, Inconel, Stellite " 21," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1946

THE committee in charge of arrangements for the meeting of the Institute in September has com-pleted its program. The headquarters of the meeting will be at the Palace Hotel, San Francisco, and the registration committee will be at the hotel all day on Sunday, Sept. 24, and from 8 a.m. until noon on Monday. On Sunday afternoon, automobiles will be available for sightseeing trips around the city. Monday will be devoted to technical sessions. In the morning, there will be sessions on Mining and on Iron and Steel; in the afternoon, sessions on Mining and Milling. At these sessions, in addition to the papers mentioned in the tentative list printed in August, there will be presented three papers on the geology, mining and milling of the Comstock lode; one on the Aztec mine, Baldy, N. M.; one on the Colombian oil fields; and one on charcoal precipitation of cyanide solutions. The luncheon on that day will be Dutch Treat, for men only, at the Engineers Club. On Monday evening, there will be an informal buffet supper at the home of F. W. Bradley. On Tuesday morning, a party of 50 men will leave for Hetch Hetchy. During the four days of the trip, the party will see the Priest tunnel and earth dam under construction by steam-shovel and hydraulic-fill methods, the Big Creek shaft and tunnel, early intake power plant and tunnels and the Hetch Hetchy dam under construction. For those who remain in San Francisco, Tuesday will be "San Francisco Day." There will be motor trips to the Presidio, Cliff House, Golden Gate Park, and other points of interest, and shopping trips to Chinatown. On Wednesday, "University of California Day," the party will be guided through the university by members of the Mining Association, the affiliated stu-dent society, and will see the Greak Theatre and not-able buildings. Thursday will be "Leland Standford, Jr. University Day." Automobiles will leave the Palace Hotel at 10 a.m., and will return from the university at 4.30 p.m. Friday has been reserved for trips to the Selby Smelter, to Mt. Tamalpais, or to other points of interest. Arrangements will be made to visit the mines or gold dredges in California, if members desire to do so, but such trips must of necessity be considered special trips and arrangements will have to be made to suit the convenience of the individual or party. The Golf Committee will make arrangements for those who wish to play golf.

Jan 9, 1922

By John J. Cioston

THE steadily rising flood of gold production from all parts of the world has created an avalanche of rumors regarding the stability of the present price of this metal. Markets have been unsettled from Johannesburg to London from New York and Toronto to Melbourne, despite repeated denials from, American and British authorities of any immediate intention to alter the price. Various economists and financial writers have blossomed forth with predictions that the price would be set at the old level of $20.67 per oz.; some have even been so brash as to state That a price of $15 would be necessary to bring production within control. These effusions, based entirely upon monetary theories and with no regard to production costs, serve to confuse rather than clarify the situation.

Jan 1, 1937

By R. C. Earlougher, F. G. Miller, T. D. Mueller, H. J. Ramey

There are many studies of flow in radial systems that can be used to interpret unsteady rerervoir flow problems. Although solutions for systems of infinite extent can be used to generate solutions fur finite ow systems by superposition, application is tedious. In this paper a step is made toward simplifying calcu1ations of such solutions for finite flow systems. Superposition is used to produce a tabulu-lion of the dimension1e.s.s pressure drop function at several locations within a bounded square that has a well at its center. The square system provides a useful building block that may be used to generate flow behavior for any rectangular shape whose sides are in integral ratios. Values of the tabulated dimensionless pressure drop function are simply added to obtain the dimensionless pressure drop function for the desired rectangulm system. The rectangular system may contain any number of wells producing at any rates. Furthermore, the outer boundaries of the rectangular system may be closed (no-flow) or they may he at constant pressure. Mixed conditions also may be conyidered. Tables of the dimensionless pressure drop function for the square system are presented and various applications of the technique are illustrated. Introduction In 1945, van Everdingen and Hurst' published solutions for the problem of water influx into a cylindrical reservoir. Since this problem is mathematically identical with the depletion of a cylindrical reservoir with a well at the origin, the van Everdingen-Hurst solution may be used to study the depletion problem. In their analysis, they assumed that the fluid had a small, constant compressibility such that flow was governed by the diffusivity equation For a constant production rate q starting at time zero, van Everdingen and Hurst showed that the unsteady pressurc distribution for both finite and infinite systems could be expressed in terms of a dimensionless pressure 'Sabulations of the dimensionless pressure drop for a unit value of r, were provided by van Everdingen and Hurst,' and later by Chatas.' Others also presented values in graphical or tabular form." If the radius of the well becomes vanishingly small, r,+ O, the line source solution may be used for Eq. 2 when infinite systems are considered. Eqs. 5 and 6 are excellent approximations for Eq. 2 under certain conditions: In 1954, Matthews, Brons and HazebroekV emonstrated that solutions such as Eq. 5 can be superposed to generate the behavior of bounded geometric shapes; i.e., the behavior of a bounded single-well system can be calculated by adding together the pressure disturbances caused by the appropriate array of an infinite number of wells producing from an infinite system. These wells are referred to as image wells. Matthews, Brons and Hazebroek considered systems containing a single well producing at a constant rate. This superposition can be represented analytically as

Jan 1, 1969

By J. E. Burke

Recent investigations have elucidated many of the phenomena of the grain growth process, but have also revealed some conflicting and unexplained results. Beck and his co-workers 1,2,3 have shown that grain growth continues with continued heating at one temperature until the average grain size approaches the thickness of the specimen. Plotting the logarithm of the average grain diameter, D, against the logarithm of the annealing time, t, they find the straight line relationship given by the equation: D = Ktm [,] with possible small deviations at short annealing times. K and n are constants at constant temperature. On the other hand, Wa1ker4 finds that, in alpha brass) the rate of growth falls off more rapidly than indicated by Eq i after long annealing, so that an equilibrium grain size is approached. Burke5 showed, using Walker's data, that time and temperature for grain growth are apparently related through an activation energy, H, according to the relationship: ] where h and tz are the annealing times necessary for the average grain size to increase from Do to D at temperatures T1 and T2 and R is the gas laws constant. In the case quoted, H had the value 60,000 cal per mol. The apparent validity of this relationship, at least up to 700°C, and the approximate value of H were later confirmed by Beck3 The results obtained by Beck Kremer, Demer and Holzworth2 for aluminum and aluminum-magnesium alloys could not be satisfied by such a relationship, since the slope of the isothermal curves increased with increasing temperature. These data indicate and Beck, Holzworth and HuV ater demonstrated expcrimentally that the only apparent factor controlling the rate of grain growth at constant temperature is the grain size. While many of the phenomena have been elucidated, a reasonably quantitative explanation of the process is lacking. There exists uncertainty even as to the primary driving force for grain growth, although there is a considerable body of indirect evidence that the interfacial energy of the grain boundary is responsible.7,8,io Making implicit use of this assumption, several authors14,16 have pointed out that grain boundaries should migrate toward their center of curvature. Harker and Parkerg have advanced this concept furthest, and show that one can expect grain boundary migration to occur only when the grain faces are curved, or when they meet at non-equilibrium angles. When the face is curved toward a grain A, for example, the atoms in the surface of grain B, on the other side of the boundary7 are on the average more surromded by the atoms of their lattice than the atoms on the surface of grain A. Because of thermal motion, the atoms at the interface will sometimes be attached to grain A and

Jan 1, 1949

By F. H. Turan, F. W. Jessen

The gel strength and viscosity of two different suspensions of fractionated montmorillonite clay were measured by using a Stormer viscosimeter and Farm V-G meter. The amount of sodium poly-phosphate (sodium bexametaphosphate, sodium tetraphosphate and sodium acid pyrophosphate) adsorbed by the clay particles was determined. A relationship seems to exist between the amount of polyphosphate adsorbed and the nature of the surface, edge or plate, assumed to be the principal sites for selective adsorption. Reduction in viscosity and gel strength was found to be directly related to the adsorption. Both chemical bonding and physical adsorption seem involved in defloccula-tion Some indication of the axial ratios of particles of .l- to .04-micron average size is possible though study of the adsorption mechanism. INTRODUCTION AND PURPOSE A knowledge of surface areas of clay particles in a suspension and a precise determination of phosphate adsorption should provide a basis for a better understanding of reduction in viscosity and gel strength caused by molecularly dehydrated phosphates. The purpose of this investigation was to study the adsorption of sodium polyphosphates on suspensions of fractionated sodium montmorillonite. Although there is considerable uncertainty regarding details of the structure of montmorillonite, a generally accepted one is that suggested by Hofmann, Endell and wi1m.l The structure shown in Fig. 1 is an idealized one, and Marshall2 has postulated that it is possible for several isomorphous replacements to occur. Thus, aluminum may replace silicon, in which case an exchangeable cation would go along with the aluminum to neutralize what would otherwise be a net negative charge on the structure. There is disagreement among various investigators as to the particle size and shape of montmorillonite clays. Marshall2 reported the following results for the mean lateral dimensions of a Putnam clay (montmorillonite)— 3,730 A° for particles having average diameters ranging from 500 to 1,000 A, and 750 A° for those with an average diameter less than 200 A. The latter particles were estimated at 50A°in thickness, which would correspond to a stack of five unit cell layers. On the other hand, Shaw3 has interpreted micrographs as indicating that particles of montmorillonite ire readilv broken down to the individual cell layers by dispersion in water. Brindley4 and Merings indicate the ultimate particles to be of the order of 300 A° in mean lateral dimension. Van Olphen6 suggested the thickness of particles at four to five unit cell layers. It was suggested also that this number tends to become smaller with increasing dilution. Recently, Kahn and Lewis7 determined the size of sodium montmorillonite particles in aqueous suspension from electro-optical bi-refringence decay curves. The

By R. W. Raymond

Since the foregoing paper (see p. 387) was printed, I have received the decision of Judge William E. Church, of the first District Court of Dakotah, in the case of Michael Duggan et al. v. John H. and Frank J. Dnvey (Silva Terra—Sitting Bull case), published in full in the Black Hills Weekly Pioneer of August 9th, 1584. The journal mentioned gives also several interlocutory decisions rendered in earlier stages of the case; but I shall quote here only so much of the final decision as bears upon the .construction of the Revised Statutes concerning the apex, the end-lines, and the extra-lateral mining right, together with a sufficient statement of the facts of the case to explain the scope of the decision. " This is an action in equity, brought in the first instance to restrain a threatened trespass by the defendants upon certain mining property in the possession of the plaintiffs, known as the ' Silver Terra' claim ; the allegation being that the defendants were about to enter, through underground workings, the ground of the plaintiffs, and remove therefrom valuable bodies of silver ore. " The answer of the defendants, admitting the acts constituting the alleged threatened trespass, further averred that they had, in fact, at the time complained of, reached and passed, in their underground workings, throngh and beyond the vertical side-line of the Silver Terra claim, and therenpon justified the acts complained of, and claimed the right to pursue their workings into and through the Silver Terra ground, by virtue of their alleged proprietorship of a vein, lode, or ledge of rock in place, hearing silver, having its top or apex within the lines of a certain other mining claim called the ' Sitting Bull,' of which they claim to be the owners, which vein, lode, or ledge extended in a continnons body of mineral-bearing rock from such top or apex to the ground in controversy, and constituted the body of ore in dispute; and that it was in the pursuit of this vein, lode, or ledge in its downward course that they had passed beyond the vertical side-lines of the Sitting Bull claim, and for some hundreds of feet beyond, into the ,ground in controversy " Subsequently, a supplemental complaint was filed, setting up the entry into plaintiffs' ground by the defendants, and their claim of right to do so, and asking fnrther relief by a decree restraining the assertion of such claim, and quieting the title of plaintiffs. "The case was tried before the court without a jnry..... " Custer hill, upon which these claims are located, is situated in the village of Galena, in Bare Butte mining district, in this county. The village lies at the base of the western slope of the hill, which presents a lateral face from south to north

Jan 1, 1884

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By M. T. Worley

This paper reports investigative work conducted to develop a method of estimating the groundwater influx from a homogeneous permeable formation into a vertical mine shaft during sinking. A method of analysis was developed using data obtained from pumping tests and a modification of the Theis non-equilibrium interpretation technique. Excess influx of groundwater into mine shafts has long been one of the more important problems encountered in the development of a mining property. Much work has been done on methods of preventing such influx and on pumping schemes to control inflow if preventive measures fail. The fundamental aspects of the problem, on the other hand, seem to have been neglected. The purpose of this paper is to review the fundamentals of groundwater flow and to propose a rapid method of analyzing hydrologic data in order to estimate influx from a homogeneous permeable formation into a mine shaft. Such an estimate of the quantity of water to be encountered is of value in planning grouting, pumping and other programs designed to control that influx. It is emphasized that the proposed method of analysis should be regarded only as a tool to be used in evaluating the problem before investing the capital necessary to begin development of a property. FUNDAMENTALS OF GROUNDWATER FLOW In order to effectively approach the problem of estimating influx into a mine shaft, a knowledge of the fundamentals of fluid flow through a porous medium is necessary. Darcy, in 1856, developed an empirical relationship to explain the flow of water through sand filters. This relationship V = k (dh/dl), is the basis for all other flow formulae. It has been shown that Darcy's relation is a solution of the Laplace equation and thus is analagous to other natural phenomena such as heat flow. Theis, using the analogy of heat flow by conduction, developed an expression for determining the transient or time-dependent groundwater flow through a homogeneous, isotropic medium. The resulting equation Was also derived by Jacob using hydrologic considerations alone.' The individual terms in the equation are described in Table I. It is important to understand the assumptions upon which this equation is based. 1) The medium through which the fluid flows is infinite in areal extent, homogeneous and isotropic. 2) The well into which the fluid discharges completely penetrates the medium. 3) The characteristics of the medium remain constant at all times. 4) The initial pressure surface is horizontal. 5) The confining media are impervious and horizontal. 6) Fluid is removed from storage instantaneously by a decline in pressure. 7) The diameter of the discharge well is infinitesimal with respect to the drainage radius of the medium.

Jan 1, 1962

By H. M. Dess, S. R. Bolin

A modifiedl Czochralski technique has been utilized to grow single crystals of YVO, pure or doped with europium or neodymium, from 1 to 2 in. long and 4 to 1/2 in. in dianz. An oxyhydrog-en gas-fired furftace zuas used in this ulork, and melts were contained in iridium crucibles. Successful application of the Czochralski ~vzethod was found to depend upon atmosphere control to prevent crusting and to limit melt decomposition, the establishment of symmetrical thermal gradients in the melt to obtain stable growth, and the selection of high-quality single-crystal seeds to prevent propagation of misorientations during growth and subsequent catastrophic cracking. The suitability of YVO4 as a host for laser-active trivalent rare earth ions has long been recognized. However, the problems associated with the growth of sufficiently large, good-quality single crystals have, until quite recently, seriously hindered satisfactory evaluation of the laser potentialities of this material. Both flux growth and Czochralski growth techniques were investigated at an early stage of interest in YVO,. The former method proved incapable of yielding crystals large enough for practical use,ly2 and the latter was beset with difficulties which took some considerable time to understand and overcome. Recently, however, the Czochralski growth process for YVO, has been improved along separate but similar lines of development by groups working independently in the Crystal Products Department of Union Carbide's Electronics Division and Bell Telephone Laboratories3 so that now good-quality single crystals of satisfactory size can be produced on a routine basis. Stimulated emission from a neodymium-doped YVO4 crystal grown by the Crystal Products Department of Union Carbide was obtained by O'connor4 of MIT, Lincoln Labs. An oxyhydrogen gas-fired furnace was used in this work, Fig. 1, and melts were contained in iridium crucibles. The starting material was 99.9 to 99.99 pct pure YVO4 powder purchased from the Chemical and Metallurgical Division of the Sylvania Electric Products Co. Typical impurity levels, determined by spectrographic analyses, were as follows: Si, 50 to 500 ppm Al, Fe, Mg, 5 to 50 ppm Ni, Pb, Mo, Mn, Ce, Cs, 1 to 10 ppm Initially, YV04 powders predoped with neodymium or europium were obtained from Sylvania. Later, however, because of a desire to grow a series of crystals containing relatively broad concentration ranges of these dopants, it proved more convenient to start with pure YV04 and mechanically admix Nd2O3 or Eu@~ powders plus equimolar amounts of V2O5. The empty crucibles were preheated to 1900" to 1950oC, a temperature range where melting occurred readily. The powdered YVO4 feedstock was then added incrementally. However, a marked tendency toward

Jan 1, 1968

By F. C. Sturges

[CONTENTS PAGE ................. Introduction-Grouting in Mines. By F. C. STURGES. I Use and Technique of Pressure Grouting in the Construction Industry. By V. L. MINEAR . 3 Technique of Pressure Cementing in the Petroleum, Mining, and Construction Industries. By WY. D. OWSLEY and R. E. MOELLER. ..................... 9 An Example of Controlled Pre-grouting in Shaft Sinking. By R. H. ALLEN and J. W. GALPIN. 15 ........ Solidifying Mines and Shafts Areas by Pressure Grouting. By B. H. MOTT 17 .............. Grouting in Southeast Missouri District. By W. W. WEIGEL 20] Introduction-Grouting in Mines By definition the word "grout" means a thin mortar, or a kind of plaster or cement, and "grouting" means to fill up or finish with grout. The words "cement," "plaster" and "mortar" mean a substance that is used in a soft state which subsequently hardens. Thus, grouting is the filling of void space with a substance that hardens. Construction cements are the most common substances used, either by themselves or in mixtures, but the term grouting is applied quite correctly when other substances such as plastics and certain chemicals are used. Also, the use of the term grouting to cover the filling of voids with materials that do not actually become hard, such as the flotation tailings used in grouting in the southeast Missouri lead district, should be considered correct, as some stiffening does take place and, anyway, it is a better descriptive term than any substitute. Engineers are interested in grouting because some of the materials with which they must work contain voids, and certain conditions can be improved if these voids can be filled with something solid and permanent. Grouting is done to accomplish several purposes: I. To stop the passage of fluids and gases, 2. To cement materials together to make them stronger, and 3. To prevent consolidation of materials by filling void space with something solid as a replacement for the air and water that could be forced out under load. The construction industry uses grouting extensively for all three purposes. Grouting is used to stop water percolation under and around dams. It is used to control water flow in tunnel driving and in shaft sinking. It is used to improve foundation conditions under civil engineering structures by permanently filling void space and thereby reducing settlement, or by cementing broken rock together and increasing its supporting strength. The oil and gas industry does a lot of grouting, primarily to stop the passage of gases and fluids. The search for oil at increasingly greater depths has meant greater investment per well, and the oil industry has spent large sums on development of improved drilling methods. This

Jan 1, 1947

By L. D. Jaffe, D. C. Buffum

EARLIER the authors and coworkers had pre sented data on isothermal temper embrittlement of an SAE 3140 steel?' In that work, however, attention was concentrated on embrittlement at 575°C and below. Preliminary measurements showed that embrittlement at 675 °C was much mote rapid than would be expected from the data at the lower temperatures: and indicated the need for further work above 575°C. The possibility of an upper nose in the time-temperature embrittlement diagram above 575°C was pointed out. Procedure The same heat of SAE 3140 steel was used as in the previous work, and experimental methods were the same. All blanks were austenitized 1 hr at 900°C and water, quenched. Groups were then tempered 1 hr at 675"C, water quenched, and given embrittling treatments for times of 5 min to 240 hr at 675" to 600 °C, as shown in Table I. Other groups, after the temper and quench, were embrittled 48 to 1440 hr at 550°C. Another series was tempered 240 hr at 675"C, quenched, and held for various times at 650" to 375°C (Table 11). For comparison, a series was tempered for these same times at 700°, 675", and 650°C (Table 111). The Ae, temperature for this heat of steel had been determined as approximately 690°C;1*a the treatments at 700°C were introduced to determine the effects of tempering in a range where a little austenite would fonn. A large number of other treatments, involving holding at two temperatures in succession after the temper, and occasionally slow cooling or heating, were also studied. These treatments are listed in the tables. Austenitizing was done in air; all subsequent treatments were in salt. Blanks were always water quenched after the last treatment. The heat-treated blanks were machined to standard V-notch Charpy specimens. A transition curve for each group was obtained by breaking the specimens at various temperatures on a 217 ft-lb impact machine having a striking velocity of 16.8 fps, and plotting the observed percentage of fibrous fracture vs the test temperature. From this plot, the transition temperature was taken as the lowest temperature at which the fracture appeared 100 pct fibrous; its accuracy is estimated as +5"C. Generally, hardness was measured on every bar. Since a decrease in hardness itself seems to decrease the transition temperature somewhat, a correctiona of —0.28"C per Bhn was applied to permit comparison of the transition temperatures on a uniform basis of 24 Rc. The transition temperature and hardness results are given in Tables I through VI. Where overlap of earlier work1.' occurred, data were combined.

Jan 1, 1958

By W. H. Brandt

THERE has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidence. Particularly noteworthy among the empirical work is that of Grossmann,12 who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.1-5 They have shown that formation of pearlite proceeds by a process of nucleation and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to fill in a small part of the gap. A method was presented recently14 for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eutectoid steel was calculated, using linear extrapolations of the ferrite and cementite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and V, the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1945

By C. P. Kempter, H. L. Brown

Recently Chang determined heat content values of tantalum monocarbide and tungsten monocarbide from 325" to985°Kand 326" to 912"K, respectively, and, using other published data, made certain solid-state calculations for these two compounds. Chang expressed his Cp values in units of cal per "g-atom alloy" OK. We consider this poor usage since l) tantalum monocarbide and tungsten monocarbide are not alloys, and 2) an atom of an alloy does not exist. However, one may convert his values to units of cal per mole OK by merely doubling them. For TaC he calculated a Nernst-Lindemann parameter of 9.07 x lo-' "g-atom per cal". We have refined the calculation of this parameter and have arrived at a much lower value. Rather than approximating the true coefficient of volume expansion, a,, as three times the true coefficient of linear expansion, a, we calculated u, from the TaCo.99, lattice expansion data of Fries and Wahman.38 At 25°C a, = 14.3 x 10s per OC. The molar volume was calculated to be 13.32 cu cm per mole at 25°C. From the lattice compression data of Champion and Drickamer~' for "TaC,.,," we determined the room-temperature compressibility to be 3.5 x 10-l3 sq cm per dyne by plotting l/Vo (aV/ap) vs applied pressure. (Since the lowest pressure at which Champion and Drickamer reported a relative volume was 20 kbars, one may calculate an approximate compressibility only. Chang calculated a compressibility of 3.175 x 10-l3 sq cm per dyne from the same data.) We also used twice Chang's value of Cp = 4.38 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated a Nernst-Lindemann parameter of 5.8 x 10-l4 mole per erg or 2.4 x lo- ' mole per cal, and a Cdil value of 2.3 x 10' ergs per mole OK. In the case of tungsten monocarbide no isothermal compressibility has been reported; however, one may calculate an approximate Nernst-Lindemann parameter by using the adiabatic compressibility reported by Brown, Armstrong, and Kempter." Using the WC lattice expansion data of Mauer and Bolz~l we calculated a, to be 12., x l0-' per OC. The molar volume was calculated to be 12.5 cu cm per mole. We used twice Chang's value of Cp = 4.18 cal per "g-atom alloy" OK for the molar heat capacity at 25°C. From these four values we calculated an approximate Nernst-Lindemann parameter of 2 x lo-' mole per cal, which is much

Jan 1, 1969

AVING started to tell you of working potter's clay for making crucibles and shells, the wish came to me to tell you of the practice of this art also. Although it may seem at first glance to be outside the order and purpose of my writing, he who considers well will see that it is not unrelated to it but proper, since it is wholly dependent on the agency and power of fire if it is to be brought to its perfection. Moreover, the potter's glazes and colors are all substances of various metals or impure minerals and therefore belong to fire. Since it is my intention to treat of fire, minerals, and metals for you, I surely should not have omitted this, particularly because it is a necessary art which enriches and is greatly praised both for its ingenuity and its beauty. The art of the potter has two sources as its principal basis. One comes from the art of design, the other from various alchemical secrets and elemental mixtures. In regard to these, I find that, in my opinion, all this art depends in the last analysis on four things: on good judgment in general, and on the art of design so as to be able to make the vessels beautiful and of good shape, as well as to ornament them with painting; after baking them well the first and second times, the next thing is to know how to make and apply the glaze well and to paint them with varied and appropriate colors. The fourth is to see that you have good, fine clay without small stones or lumps-indeed this is to be considered as the first thing. Now this that I have called clay is what many call cretaceous earth and some call argil. It is found and dug up when the masters wish to make use of it and is put in a container to be moistened. When it is moistened, it is beaten on a bench with an iron rod and very well prepared. Mixing it carefully, every small stone, lump, or other hardness that it contains is removed and cleaned away. Then a shaft [145V] of iron is fitted as the journal in a large wheel. On the other end of the journal a small wheel is made which forms an instrument for working that is called a lathe. Having put some clay on this, it is made to rotate by pushing with one foot, and, by rotating it, vessels are worked into a pleasing shape and size. Then they are taken off and put on a board to dry. After drying artificially or naturally they are painted red,

Jan 1, 1942

Manganese Resources in Relation to Domestic Consumption Discussion of paper by JOHN V. W. REYNDERS, presented at the Cleveland Meeting and issued, as Pamphlet No. 1656-C, with MINING AND METALLURGY, May, 1927. A. G. BETTS, Kinderhook, N. Y. (written discussion).-When a business concern hires an office boy, it takes on the first bright-appearing young chap to apply and pays him the prevailing rate of wages. One of the chief tasks the .office boy is supposed to be competent to perform, is to clean out the office. The manager of the business is highly competent in many lines, but for some reason lacks the ability to keep the office clean. To the steel man, it would seem that manganese is the office boy, and it is purchased just as found and offered to the purchasing agent. The steel mill is competent to perform many functions on a grand scale and with wonderful efficiency, but it is unable to make real steel. It is the function of the office boy, manganese, to do this. It is open to serious doubt if steel mill operators have ever taken seriously the metallurgy of the preparation of crude manganese. It has merely been found that some usable crude manganese may be obtained by running certain manganese ores through an iron furnace when not busy on anything else, or remote from iron ore, or with a lining that is about gone. It is, however, an entirely unwarranted assumption that the metallurgy of manganese has been worked out, or that the supplies of usable raw ore must be limited to materials of some specified analysis. There was a time when ores of copper, lead and zinc, for example, had to be rich and of specified analysis, to be usable, but the commercial raw materials of today bear little resemblance to such ores of the past. The discussions of manganese that I have seen are based on the assumption that the metallurgy of manganese is fully established and that the only usable manganese raw materials are of the kind used today. These discussions contain another error, not so much of statement, but of implication-that the tonnages of manganese materials in the United States are so much in this state and so much in that. When it requires a period of years and the expenditure of millions of dollars for a competent mining company to explore thoroughly a few acres of mining ground, is it not absurd to say that there are so many hundred tons of manganese ore in a certain state? This fact is not apt to be known fully in 10,000, years. I do not charge the mining engineers. who are on record, of making misstatements, because they merely say that so much

Jan 5, 1927

Discussion of the paper of H! M. CHANCE, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 91, July, 1914, pp. 1461 to 1466. R. V. Norris, Wilkes-Barre, Pa.-In his resume of coal-taxation methods Mr. Chance has apparently confined his investigation to bituminous coal, so a summary of the anthracite situation as to coal assessment should be of interest. The anthracite region of Pennsylvania in its 484 square miles of measures lies in the counties of Wayne, Lackawanna, Luzerne, Carbon, Schuylkill, Northumberland, and Dauphin, and in each of these different methods of assessment have been adopted. The assessments for taxation in Pennsylvania are made under Acts of the Legislatures of 1841 and 1842, under which the assessors are re¬quired to "assess rate and value every subject of taxation according to the actual value thereof, and at such rates and prices as the same would bring at a bona fide sale after due notice." Under this general law coal land has been assessed as such, but up to about 25 years ago the coal was assessed at rates so low as to be unimportant, though the rates in each township and municipality, even in the same county, showed no agreement or ascertainable basis. In the late '80s, the need for greater revenue drew attention to the possibilities of collecting much larger taxes from the coal lands and, spurred by public demand, the assessing authorities in some counties undertook a reassessment of coal. The method pursued was to demand from each owner a statement of the area and average remaining thickness of coal on his lands. On this return, made in some cases under oath, an assessment based on foot-acreage was levied, with a resulting great increase in valuation, but the valuation per foot-acre was low and no serious objection was made. This assessment with occasional increases of rate remained in force until 1907, when, in the triennial assessment of that year, a complete revision of the valuation was again attempted, engineers were employed by the counties to check the accuracy of the returns from the owners, and, based on the foot-acreage thus obtained, an enormous increase, to $65 per foot-acre, was made in the valuation. This assessment was resisted in the courts by appeals resulting in very extensive litigation, and a final determination of the validity of the 1907 and all subsequent assessments has not yet been obtained. In the first appeals tried the rate calculated on a foot-acre valuation was reduced by the Luzerne County court to about $45, while the. Lackawanna County courts reduced a larger rate to $67. The county authorities were, how-

Jan 4, 1915

By H. H. Stout

IN the early fall of 1025, the writer was conducting, in the Ledoux and Co. labora-tory, New York, experiments directed to-ward ascertaining the effect on its impurity content when cathode copper was subjected to a current of various gases at an elevated temperature below the melting point. The apparatus consisted of a vertical I-in. dia. silica tube about 12 in. long, heated on the outside. The cathodes were broken to pass 3/8-in. mesh, and a current of various differ-ent gases was passed up through a 4-in. long column of these loose cathode particles in the vertical tube furnace. Temperature was maintained to 1500° to 1600°F. and the gas treatments lasted from 3 to 6 hr. The writer observed that whenever reducing gas (H2 or CO) was used, these cathode par-ticles stuck together at points of contact with each other. The cohesion was so marked and tenacious that an examination was made of the fractured surfaces, when cathode particles were broken from the cluster. Crystal growth was always found to have taken place across the surfaces where separate particles were in contact, but only after all oxides, sulphates, etc., had been completely removed. The idea of a possible new process was then conceived and was disclosed to A. M. Smoot (V. P. Ledoux and Co.) with intent to obtain his views. The first conception as given Smoot was "to gas-clean broken cathodes, put them in an extrusion press, solidify and extrude them at around 1500°F." Smoot's reaction, after a few moments considera-tion, was, "It looks perfectly all right to me." The writer and his assistants, W. H. Osborn and H. H. Stout, Jr., after confer-ring as to ways and means, decided to go ahead with preliminary laboratory experi-ments, which, it was thought, would move the new process from the possible to the probable. This program followed a course indicated by three basic considerations: I. Since brittle cathodes were often unin-tentionally produced, it seemed probable that the laws controlling this type of deposi-tion could be ascertained. 2. We had already proved the gas-clean-ing feature. 3. There remained to prove: whether a sound, homogeneous metal billet could be produced with crystal growth established over the entire surface of each individual particle in the billet; and, if so, what would be the physical properties? Osborn arranged with Columbia Uni-versity for conducting experiments in its research laboratory to prove or disprove the third item; Columbia assigned C. A. Phillipi, Jr. to assist in the project. A press with a cylinder 2 in. high and of I-in. dia. was used. It was surrounded and heated by a resistance coil of Nichrome wire. Broken tough cathodes were used.

Jan 1, 1940

By William B. Stephenson

The paper describes efficient and effective methods of automatically controlling sand pump installations. Particular reference is made to liquid-level controls actuating variable speed pump-driving units. Included is a discussion of various combinations of equipment, with schematic drawings. HERETOFORE many sand pump installations in the mining and metallurgical field involved guesswork as to the size of the pump and then simply direct-connecting it to a constant speed motor which was often large enough to do twice the work required. Considerable thought was given to mill location in an effort to avoid as much pumping as possible. Hillside design of mills with gravity flow of tailing was much to be desired. Power costs were low, construction was relatively cheap, and labor in many places meant nothing in comparison to the values derived from the ores being treated. Today most of these conditions are reversed. Ores are becoming more complex with lower values per ton of ore treated. Power is more expensive, construction is higher, and labor definitely takes a very important place in the profit and loss statement. Each piece of equipment incorporated in the design of a new mill is selected to provide highest efficiency based on careful metallurgical analysis of the ore to be treated both in good and poor markets. Each is designed with its flexibility in mind and with provision for adjustments in its performance to meet actual conditions in the operation of the mill. Sand pumps have taken an important position in mill design. Operators the world over are relying more and more on the performance of a sand pump in the efficient operating of their plant. Many ordinary jobs are being done today with pumps driven through adjustable pitch diameter V belt drives in order that changes in pump speed can be made easily to meet actual operating conditions. Operating costs have long since proved the folly of operating a pump at too high a speed for the volume and head to be overcome. Metallurgical results have shown the benefits derived from a smooth flow as contrasted with a surging flow from an uncontrolled pump. Construction costs have risen to such an extent that surge bins and other means formerly employed must be omitted from today's flowsheet. Several installations of considerable size and involving the use of automatic pump speed control have proved the adaptability of such controls since they were placed in service in recent years. In the following presentation each system discussed and illustrated schematically has been installed in one or more instances and has proved itself reliable and definitely economical from the standpoint of capital investment, operation and maintenance. Variable Volume-Head Speed Control: Probably the most popular, effective and efficient automatic control setup for sand pumping installations is the one shown schematically in fig. 1. Commonly used

Jan 1, 1951