Search Documents

By A. U. Seybolt

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By J. B. Macelwane

Geophysics differs from geology and physics in in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, vol-canology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratow system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist—the exploration geophysicist —calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist—the paleontologist— needs some knowledge of geology. Development of a Geophysicist Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydro1 ogist, or an exploration geophysicistp we may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1946

By J. B. Macelwane

GEOPHYSICS differs from geology and physics in many respects. In the first place, geophysics is a complex science embracing the fields of seismology, geomagnetism, geoelectricity, geodesy, meteorology, volcanology, physical oceanography, physical hydrology, tectonophysics and exploration geophysics. Geology is also a complex science and so extensive in its various fields that no one can master them all, and no part of geology deals in any sense with several of these fields of geophysics. In the second place, geophysics makes use of methods and instruments that are derived primarily from the science of physics. Geology, on the other hand, has methods of its own and it draws its borrowed techniques and its instrumental equipment not only from physics but also and perhaps primarily from chemistry and biology. The difference, therefore, between the geophysicist and the geologist lies partly in the phenomena that are observed, partly in the methods and instruments with which each carries on his exploration; but partly also, and perhaps principally, in the habitual attitude of mind and in the background of specialized training with which each approaches the problems presented by this planet of ours. The geologist as such, therefore, is no geophysicist. On the other hand, the physicist is not a geophysicist either. Isolation of each problem in a closed laboratory system under complete control is fundamental to the methods of the physicist. The geophysicist must apply physical instruments and physicomathematical reasoning to the study of physical quantities in their undisturbed natural environment. What, then, is a geophysicist? In the sense that he is a trained expert in all of the geophysical sciences, I do not believe that such a person ever existed. It would be beyond the possibilities of a single lifetime. I think there is confusion in our ideas and in our use of terms. We are not all thinking of the same thing when we say geophysics or geophysicist; yet we seem to talk as though we were. It is as absurd to say that the whole of geophysics belongs to geology because the field of a particular type of geophysicist-the exploration geophysicist -calls for some knowledge of geology as it would be to say that the whole of biology belongs to geology because a particular type of biologist-the paleontologistneeds some knowledge of geology. DEVELOPMENT OF A GEOPHYSICIST Since it is impossible to become an expert in all the fields of geophysics, and since students entering college seldom know the field they will choose as a career, what would we suggest as the best general preparation for work in geophysics, whether as a meteorologist, an oceanographer, a seismologist, a geodesist, a geomagneticist, a volcanologist, a tectonophysicist, a hydrologist, or an exploration geophysicist? We may distinguish five phases in the development of a geophysicist: (I) his mathematical and scientific studies in high school; (2) the general mathematical and scientific

Jan 1, 1941

By Marsh S. Watson, Robert A. Howard

An electrolytic model study has been made of the relative productivity of perforated casing. The results show that the relative productivity is roughly one-half to two-thirds of that predicted from point-sink calculations. This discrepancy can he satisfactorily explained on the basis of casing interference. The relative productivity was found to he insensitive to spatial arrangement of the perforations. INTRODUCTION The relative productivity of wells with perforated casing has been treated mathematically by Muskat.' In his treatment the perforations are represented by small spheres, thus enabling him to approximate the flow by that to point sinks. By neglecting interference between the flow into the various spheres representing the perforations, one may deduce the approximate formula Qu 1/rp - 1/rw • (1) I + b/2n _________ 2n In re/rw Where Q is the flow rate into spherical sinks located in the median plane of the sand laver Qo is the open hole flow rate (uncased hole of radius rw) b is the thickness of sand layer under consideration (always one foot in this paper) n is the number of spherical sinks in the sand layer rp is the radius of a spherical sink rw is the well radius re is the drainage radius of the well. Fig. 1 is a comparison of values calculated from equation (1) with Mus-kat's values. It will be observed that the approximate values are in error by less than 21/2 per cent. The disturbing effect of the casing on the flow line; is not explicitly taken into account by Muskat, but he reasons that interference between the flow pat- terns from the various point sinks will result in a negligible flow in the region within the well radius, and that no appreciable error will result from not explicitly excluding flow from this region. This line of reasoning is open to question, however, as the flow impedance, in the immediate vicinity of the well, of a hemispherical cavity in contact with an opening in the casing is twice that of a spherical sink in a continuous sand layer. There will be a difference, moveover, between the flow into a hemispherical cavity and that into a circular hole in the casing. .This latter difference can best be appreciated by comparing the flow from a semi-infinite medium into a hemispherical cavity at the edge of the medium with the flow out of a circular opening of the same radius as the hemisphere and which is also on the edge of the medium. In this case2 ------= —2, showing that the difference in flow rates into differently shaped cavities is quite appreciable. It was the purpose of the investigation reported here to determine to what extent flow into circular perforations in casing departs from the values calculated by Muskat. For this purpose an electrolytic model was used.

Jan 1, 1950

Using 5-p Ni powder and 0.018 ,u A1203, oxide dispersion strengthened nickel alloys were prepared by mechanical mixing of powders, followed by compaction, sintering and extrusion. Processing variables such as cooling of the powder during mixing, electrostatic discharging, mixing time, amount of oxide, and so forth, were studied to determine the effects on room-temperature tensile and high-temperature creep-rupture properties and on the reproducibility of alloys. MECHANICAL mixing of metal and metal oxide powders provides one of the simplest and most inexpensive methods for preparing dispersion strengthened metal-metal oxide alloys;" however, because of large differences in specific gravity, powder particle diameters and other variables, difficulties have been encountered in reproducing alloys and alloy properties. Using 5-p Ni powder and 0.018 p A1203, the following variables were investigated: a) Blending techniques b) Blending time c) Volume fraction of oxide for the selected pow- ders d) Sintering of compacts before extrusion Cooling of Powders During Blending— Cremens and Grant had indicated that dry ball milling of the powder mixture gave superior results over other procedures. When ultra-fine metal and oxide powders became available and comminution was unnecessary or offered little gain, the use of dry mixing in a Waring Blendor gave optimum results.' In the current study, observations of the powder mixtures indicated that considerable heat was generated due to the high speed of the Waring Blendor (15,000 rpm). This heating appeared to produce some degree of clustering and pelletizing. To minimize such agglomeration, a Pyrex cooling coil was installed in the mixing vessel. A double coil, water cooled, proved to be quite satisfactory, providing a fair degree of cooling along with good erosion resistance. Discharge of Electrostatic Charge—Electron-microscopy showed that agglomeration was minimized by the cooling procedure but was not entirely eliminated. It appeared that some of the ag- glomeration had to be explained on the basis of an electrostatic attraction due to the high-speed blending operation. These charges had the effect of promoting the growth of alumina clusters. At the end of the blending procedure such clusters had an effective size which was as much as 50 times that of the individual powder particles and were very tightly bunched. Several methods were utilized to try to discharge the electrostatic forces to minimize the clustering. One successful method, utilized in alloy 17, involved continuous exposure during blending to a radium source of 50 millicuries at a distance of 1.5 ft from the container. A number of other methods were noted to work equally well. Fig. 1 shows the more open oxide structure which results from such a treatment, permitting the matrix metal to penetrate into the cluster more effectively. The combination of powder cooling and discharging led to noticeably improved structures. Fig. 2 shows a cross and a longitudinal section in alloy M-17, one of the best alloys, illustrating the marked decrease

Jan 1, 1961

By D. H. Baldwin, R. E. Reed-Hill

DURING the course of experiments involving oxygen equilibrations with a high-purity Pd-5 at. pct Rh alloy, the appearance of a subscale was noted. Most of the heat treatments in a pure oxygen atmosphere were performed at 900°C. The presence of the subscale was noted when the oxygen partial pressure was in excess of approximately 95 mm, up to 1 atm, the highest pressure used. According to available thermodynamic information' on the free energy of formation of Rh2O3 (the only reliably reported solid oxide of rhodium), this oxide should not be stable under these conditions, nor, of course, any oxide of palladium. Extraction of the subscale from the matrix was affected by treatment with aqua regia, and the resulting X-ray diffraction powder pattern is shown in Table I. This pattern is not that of Rh2O3, nor that of any known rhodium or palladium oxide. It can be indexed on a hexagonal lattice with a. = 5.22Å and co = 6.0Å. In addition to this unknown material, there was a weak Rh2O3 pattern. An X-ray fluorescence analysis of the powder gave 3214 palladium counts per sec and 5381 rhodium counts per sec, thus indicating the likelihood of a double oxide of palladium and rhodium. In view of the fact that the above result was obtained on a single sample, it is perhaps best not to insist upon the above ratio of about 0.6, but possibly to tentatively assume 0.5 or 1/1. The small amount of Rh2O3 in the X-ray pattern might have occurred on cooling, and it seems possible that the double oxide, below some temperature level, is not as stable as Rh2O3. To examine this point, some of the extracted double oxide was heated on a sheet of pure palladium in air at 900°C, and allowed to furnace-cool over a period of several hours. The X-ray diffraction pattern of the powder showed approximately the same intensity of Rh2O3 and the "hexagonal" oxide as before, but, in addition, a rather faint pattern of another crystalline species made its appearance. This finding again suggests partial transformation of the major (double) oxide to other oxides on cooling from 900°C. Application of the phase rule shows that only one equilibrium oxide (subscale) could have been present at temperature. Vacuum-fusion, oxygen analysis of the extracted subscale showed 7.7 ± 0.7 pct O. Combining this information with that of the X-ray fluorescence analysis suggests the formula PdRhO. This compound should have an oxygen content of 7.07 pct, which is within the range of error of the oxygen analysis. However, until a more careful stoichiometric study is made, it is suggested that the formula be written

Jan 1, 1965

By H. L. Talbot, A. J. Hall, R. S. Young

A method for the chemical differentiation of oxidized cobalt from sulphide cobalt in complex mine and concentrator products is of considerable interest to a number of mining companies throughout the world. At Rhokana Corporation, in Northern Rhodesia, for instance, cobalt is found chiefly in the sulphide form, as carrollite, but a cobalt oxide mineral also occurs irregularly underground, and relatively small quantities in the mill feed from time to time are difficult to detect visually at the concentrator. The oxide cobalt is not amenable to the sulphide flotation process used at Rhokana and nearly all of it passes into the tailing. The occasional period when high tailing losses occur with no appreciable change in the cobalt content of the mill feed has naturally been disturbing to the concentrator staff, who had no means of determining whether an influx of cobalt oxide ore or laxity on the part of the mill flotation operators as responsible for these results. A procedure for determining oxidized copper minerals, based on their solubility in dilute sulphuric acid saturated with SO2, has been used for many years in the copper industry. In the presence of cuprite the procedure fails, but otherwise it gives results quite satisfactory for control pur- poses. Empirical methods for determining oxidized forms of zinc and lead have been proposed, but they are generally unsatisfactory except in isolated cases of a very simple ore. No published procedure for determining oxidized forms of cobalt or siinilar elements has come to the authors'notice. Experimental Procedure There are obviously two alternatives in attacking a problem of this nature. One is to employ a solvent for oxide cobalt that will not dissolve cobalt sulphide. The other is to find a substance capable of oxidizing the cobalt sulphide to sulphate, which of course is water-soluble and can then be leached from the water-insoluble oxide cobalt. A representative sample of Rhokana cobalt oxide ore was secured, ground to minus 200-mesh, and carefully rolled to furnish a standard sample for this work. The analysis of this material gave the following percentages: Co, 0.55; Cu, 1.64; Fe, 2.98; S, 0.08; SiO2, 41.42; Al2o3, 11.20; CaO, 13.82; MgO, 3.80. As a source of cobalt sulphide a similar large sample of carrollite was prepared, analyzing Co, 23.36 per cent; Cu, 27.32; and S, 31.13. This sample of course was not pure carrollite, but was the best obtainable in quantities sufficient for a standard intended for considerable work. It was a pure sulphide sample, microscopic examination showing only carrollite, a little bornite, and gangue, with no visible sign of oxidized ore present. A wide variety of reagents as used in an effort to selectively dissolve oxide cobalt or to oxidize sulphide cobalt to

Jan 1, 1949

By James Terry Duce

In order to facilitate interpretation of the data in this chapter, we print the following excerpts from circulars to authors, compiled by Mr. Frank A. Herald when he was Vice-chairman for Production of the Petroleum Division, and revised in 1939. Generally in Table 1 the unit for prescntation of data is a field. For our purposes a field is defined as the whole of a surface area wherein productive locations are continuous. Such unit commonly includes and surrounds nonproductive areas. Such unit commonly includes a great variety of geologic conditions—several units of continuous productive reservoirs of distinctly different structure and of distinctly different stratigraphy. Therefore it is hoped that our authors will subdivide "field" so as to enable students to make analyses that may have scientific and /or commercial value. As to each spacc in the tabulation, it is citller (1) not applicable, (2) the proper entry is not determinable, (3) the proper entry is determinable, but not determinable from data available to the author, (4) the proper entry is determinable by the author. In spaces not applicable, the author will please draw horizontal lines; in spaces where the proper entries are not determinable, the author will please insert x; in spaces where the proper entries are detcrminable but not detcrminable from data available to the author, the author will please insert y; in spaces where the proper entries are determinable by the author he will, of course, make such entries. Generally, y implies a hope that in some future year a definite figure will be available. Inability to determine precisely the correct entry for a particular space should not lead the author to insert merely y. Contributions of great value may be made by the author in many cases where entries arc not subject to precise determination. In such rases the author should use his good judgment and make the best entry possible under the circumstances. For many spaces, the correct entries represent the opinion of the author (for example, "Area Proved") and in such cases the entries need not be hedged to such extent as in cases where the quantities are definite yet can be ascertained only approximately by the author. In cases under definite headings but where figures are only approximate, the author may use x. For example, if the total production of a field is known to be between 1,800,000 and 1,850,000, the author may report 1,8xx,xxx; or if the production is between 1,850,000 and 1,900,000, the author may report 1,9xx,xxx. Where a numeral is immediately to the left of x or y, such numeral represents the nearest known number in that position. As to quantity of gas produced from many fields the question will arise as to whether the figures should include merely the gas marketed or should include also estimates of gas used in operations and gas wasted. Although rough approximations

Jan 1, 1939

By John Hays, Hammond

IT is both a pleasure and an honor to be a guest of the Institute and I thank you, Mr. President and fellow-members, for giving. me the opportunity of meeting you this evening. My esteemed friend, President Smith, has requested me to do a bit of "reminiscing" as to the earlier years of my career as a mining engineer, which has now covered a period of fifty years. Let me reassure you by promising that my narrative will not include all the experiences I have had over that long period. You will, I trust, pardon what might seem egotistical but I do not see how a personal narrative could well be otherwise.

Jan 1, 1928

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By R. K. McGeary, B. Lustman

Orientation relationships and rates of annealing of 97 pct cold rolled zirconium have been studied by X-ray techniques, metallography, and by hardness measurements. The process of annealing occurring by the formation of domains, and their subsequent growth without recrystallization, is demonstrated. NUMEROUS investigators1-' have revealed sub-grain formation after annealing cold worked metal single crystals and have generally described the results in terms of a dislocation mechanism of polygonization.5,6 in heavily cold rolled polycrystal-line aluminum the first stages of heating cause an apparently spontaneous subdivision of regions of the deformed matrix into a great number of slightly disoriented domains followed or accompanied by rapid growth of certain domains to form a recrystallization texture.7,8 In the present investigation the isothermal rate of annealing of cold worked polycrystalline zirconium has been studied by X-ray techniques, metallography, and by hardness measurement. It will be shown that, rather than by the usual nucleation and growth mechanism,"12 the process of annealing can best be explained by the formation of domains early in the annealing treatment and the subsequent growth of these domains without recrystallization. Experimental Procedure All the experimental work was performed on an arc-melted ingot of high purity zirconium crystal bar made by Westinghouse in a production scale deBoer unit. The weight percentage of impurities in the zirconium were as follows: C, 0.04; Fe, 0.05; Hf, 0.014; W, 0.01; Ti, Ni, and Al, 0.003; Si and N, 0.002; Cr and Cu, 0.001. Metallographically the zirconium showed only a single phase. The 4 in. diarn ingot was forged at 760°C to a 1 1/2x3 in. plate and was then rolled at 760°C to 0.150 in. thickness and annealed at this temperature for 20 min to produce an equiaxed grain structure of about 0.1 mm average grain diameter. The hot rolled plate was roller-leveled, surface ground to 0.135 in., cold rolled 83 pct reduction in thickness on a two-high mill, and then to a total reduction of 97 pct on a Sendzimir mill. The 0.004 in. strip material so produced received no subsequent mechanical treatment. Specimens % in. square were sheared from the rolled strip and isothermally annealed at 104 mm Hg in an all glass vacuum system equipped with a Vycor furnace tube. The temperature data presented are the average temperatures during the runs and did not vary more than about k3"C. X-ray Diffraction Methods: When zirconium is drastically cold rolled, a high degree of preferred orientation results in which prism poles, {1010}, are perpendicular to the rolling direction. After fully annealing this material an entirely new texture develops which corresponds to a 20" or 40" rotation of the deformation texture about hexagonal axes of

Jan 1, 1954

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By W. J. Tait, A. E. Craig, E. P. McCurdy

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951

Taking the Long View THE present international situation has serious implications for this nation. The possibility of total war is no more appalling than the threat of making the United States permanently into an armed camp. A period of ten years under such conditions could mean a Communist victory without firing a shot-if the present trend toward statism is allowed to continue. As individual citizens and as members of the mining profession we have the power to oppose the march toward socialism. We must not adopt shortsighted policies dictated by self-interest, but must endeavor to size up the situation as a whole and act according to what will be best in the national interest. The economic picture for the metal mining industry under present emergency conditions is apparently bright. Demand for metals exceeds supply. But there is danger that fluctuating prices will bring Government regulation. Care must be exercised in our pricing policies, or the calamity of Government intervention will be inevitable. President Truman's "loophole" reference to percentage depletion early in the year caused a brief flurry of excitement, but now that the immediate threat is over the industry has lapsed into sommolence on this subject. Special tax privileges accorded the mining industry because of inherent risks should be guarded by a continuing propaganda campaign to educate Congress and the public. If this is not done we may find ourselves losing the necessary tax protection which we now possess by a capricious act of legislation. Stockpiling minerals from abroad certainly lengthens the life of our own mineral resources. The present consumer demand for the base metals indicates foreign sources of supply for stockpiling. However, this is only one facet of the problem. For strategic military reasons it is necessary that the United States have quick sources of all minerals within our national boundaries. Undeveloped mineral deposits do not meet this need so that where it is possible to encourage our own mineral development by stockpile purchases, it should be done. A need exists for an overall controlling agency that would make purchases for the stockpile according to military necessity, current metal market conditions, and so as to strengthen the mining industry. In the course of the history of the United States we have been engulfed in several wars by the necessity of protecting our economic rights abroad trading privileges-and also because of moral obligations. Disregarding the moral side, it is difficult to reconcile fighting wars to protect world freedom of trade when in peacetime we attempt to restrain such trade by tariff barriers. When it comes to accepting subsidies from the Government in one form or another it is difficult to overlook the immediate personal gains and see in the future that where the Government lays out capital it becomes a partner in the business and not a silent one. It is apparent that hope for the traditional American way of life cannot be bought without some self-sacrifice; and we cannot wait for the other fellow to start it because it is the responsibility of each individual citizen. By taking the long view our course should be apparent and not diverge sharply from our own personal benefit.

Jan 10, 1950

By Walter Bonsack

THE CHAIRMAN.-This is the third and last session of the Institute of Metals Division's Symposium on Secondary Metals, and certainly the best of those that I have attended in the last few years. I would say that the increase in interest in secondary metals is quite noticeable by the steadily increasing attendance at these meetings. We have heard about the necessity of utilizing salvaged materials, but we still speak about them as low-grade, or down-graded materials. We still have the wrong perspective. We must willingly admit that these materials are valuable; we cannot go on using the choicest primary metals as morsels for our economic diet in a war of such unbelievable dimensions. This brings up the question-why are we so selective. The answer certainly is not that we know nothing else will do, but rather that we do not know what else will do. To be honest, we should admit our lack of knowledge concerning our complex alloys. Compared to the organic chemists, we metallurgists are very conservative, and the sooner we realize this and start to overcome it the better, because if we do not eliminate this difference, many customers of the metals business will go over to the plastics. If we take for example the development of aluminum alloys, you will see what I mean. From the binary aluminum alloys of 1920, we have progressed to ternary and quarternary alloys in the 1930's. We are only now beginning to use more complex alloys as we are forced to learn more about the effect of various elements on existing alloys. The effects of these elements should be studied now. They can be studied by two methods of approach. The usual method is to start from the base alloy and add various elements one by one in increasing amounts and study the resultant changes in properties. This is a tedious, long way. The other method which the smelters frequently use is to take the off-grade heats and study their characteristics. While the producer of primary alloys often has difficulties in alloying certain elements with the alloy under investigation, the smelter often finds them well alloyed in his raw materials and has no difficulties at all. Elements such as lead are difficult to alloy with aluminum and they tend to segregate severely. However, the amount which will remain alloyed in the metal is usually found in some "secondary" aluminum alloys. If one considers such concentration as the saturation, then by dilution with the same type of alloy, but free of such element, one can produce numerous intermediary alloys for investigation. In this fashion one is fairly certain to get uniformly spaced concentrations of the element under investigation. Similar cases probably exist with other metals. Nevertheless, the amount of work necessary to study all possible combinations is still tremendous. Necessity forces us now to utilize alloys which contain more elements than we are accustomed to. It is, therefore, necessary to study carefully the more complicated alloys. In secondary aluminum we are working and using the alloys which contain as many as 6 to 10 elements and we have learned over a period of several decades to balance

Jan 1, 1943

By Robert M. Dreyer

Although lateritic ore deposits are relatively flat-lying, surficial ore bodies, the evaluation of lateritic bauxite and nickel deposits is among the most difficult problems confronting an economic geologist. Laterite is a soil formed under tropical conditions resulting in the concentration, within the soil zone, of certain trivalent metals - principally iron and aluminum, but also, locally, nickel and manganese. The soil zone is divided into two parts: (a) the true soil or lateritic zone and (b) the zone of partially altered bed rock or saprolite. Whereas bauxite generally is confined to the lateritic zone, some nickel deposits occur in both the laterite and saprolite zones. The evaluation of bauxite and lateritic nickel deposits thus has both similarities and differences. These ores have been formed by supergene, soil-forming solutions moving downward through zones of widely varying permeability within the weathering rock. Because the permeability varies widely, both vertically and laterally. the extent of weathering may vary greatly within short distances. Because the weathering process varies widely, the degree of metal concentration may also vary widely. It is not at all uncommon for a laterite to change, within a few centimeters, from a virtually valueless rock to a high grade ore. Moreover, the depth of weathering, and hence the depth and form of the ore profile, vary greatly. Obviously, for this type of deposit, a few grab samples or a few drill holes are virtually worthless. The evaluation of such a deposit requires a sophisticated statistical study based on thousands of carefully selected samples. As a rule of thumb, the cost of evaluating a large bauxite or lateritic nickel deposit will be about one cent per ton of ore in the ground. Thus, the cost of evaluating a several hundred million ton deposit may be considerable. The following factors must be considered during the evaluation: Type of Sampling: The best and most reliable samples for the evaluation of lateritic ores are taken along large, vertical channels in hand-dug pits. Where labor costs are high, some form of drilling may be used in place of pitting, but it is always wise to choose a drilling procedure after checking drilling results against a series of pit channel samples. The drilling may not reproduce exactly the results from pit channel samples, but it may be possible to derive a constant correction factor. If the physical character of the laterite varies within the deposit, it may, of course, be necessary to change the type of drilling, the correction factor or both. In some areas, it has been found empirically that augers, chum drills, vacuum drills, rotary drills, or core drills yield satisfactory results. The problem is to find which drilling technique gives results most similar to channel samples through the heterogeneous sequence characterizing the laterite in a given area. In lateritic nickel deposits, the drilling characteristics of the lateritic and saprolitic portions of the deposit are very different. Within the saprolite, the major nickel values are commonly found in weathered zones within less altered boulders - a type of occurrence which makes sampling very difficult.

Jan 1, 1979

ASIDE from the John Fritz Medal, in which the Institute participates through its representation on the John Fritz Medal Board; the Institute itself has three awards to make annually, as follows: the Robert W.' Hunt Medal and Prize, the J. E. Johnson, Jr. Award, and the James Douglas Medal. ROBERT W. HUNT MEDAL AND PRIZE The partners of Robert W. Hunt established a fund which was presented to the Institute at a fitting ceremony on May 27, 1920, to establish an annual medal and a sum of money to be awarded under the following rules: 1. The award shall consist of two prizes; first of a. gold medal, second of a sum of money; a certificate to accompany each prize. The money prize shall not be awarded to a member over 40 years of age, but under unusual circumstances, both prizes may be allotted to one person provided that he is not over 40 years of age. In general it will be understood that the Committee shall award the money prize to the younger men, rather than the medal. 2. The awards shall be made not oftener than once a year to that person or persons contributing to the Institute the best original paper or Papers on iron and steel. The scope of the term "iron and steel" shall be determined by the sub-committee considering the awards. In general, papers dealing with the practical side of. the subject have preference over those dealing with the theoretical, side in recognition of the fact that Captain Hunt's main contributions to the industry have been in the improvement of production and quality of material. 3. A sub-committee of three to five, including the Chairman of the Iron and Steel Committee, shall be appointed by the Iron and Steel Committee annually to adjudge the. award subject to approval. 4. The awarding committee shall submit its report to the Iron and Steel Committee at its October Meeting, and the award shall be certified to the Secretary of the Institute in time to permit the presentation to be made at the Annual Meeting of the Institute. 5. The recipient of the award shall be designated "The Hunt Medallist." This prize is administered. by the iron and Steel Committee. J. E. JOHNSON, JR., AWARD This award is made from the income of a fund of $30000 donated by Mrs. Margaret Hilles. Johnson in memory of her husband, J. E. Johnson, Jr., who was a prominent engineer, author of two valuable volumes on iron blast-furnace construction and practise, vice-chairman of the Institute's Iron. and Steel Committee, and a frequent contributor of papers to the Institute's TRANSACTIONS. This prize is administered by the Iron and Steel Committee. The intent of the donor is to encourage young men in creative work in branches of the metallurgy or manufacture of pig iron with which the professional activities of Mr. Johnson were chiefly concerned. The control off the fund and distribution of the awards having been vested in the Board of Directors of the Institute, this Board has made the following regulations concerning it:

Jan 1, 1925

By Cecil Desch

THIS annual lecture, under the auspices of the Institute of Metals Division, and which was illus- trated by lantern slides, has been printed in full and a limited number are available for distribution on request. Some excerpts from the lecture are given below: Ever since the simple geometrical relations of crystals were discovered, it has been recognized that their proper-ties are best explained by assuming that their ultimate particles are arranged on a space lattice, and that the char-acteristics of that lattice determine the shape of the crystal and its physical and mechanical properties. Modern ex-amination by means of X-rays has widened that concep-tion and given it greater; definiteness, and the atoms are now regarded as the particles forming the space lattice. The splendid achievements of investigators in this field have made it possible to state, for a large number of sub-stances, the form and dimensions of the lattice. The char-acteristic of a lattice is that a unit of simple geometrical form is repeated at regular intervals in three dimensions so as to fill the entire crystal. It follows that there must be certain planes in which the atoms are more closely packed than in planes drawn at any angle to them, and it is these planes of closest packing which play the greatest part in determining the growth and other properties of the crystal. There are actually two stages in crystallization, what-ever be the medium in which it occurs. The first is the ap-pearance of crystal nuclei; the second the growth of those nuclei to form crystals of appreciable .size. The first is clearly a kinetic phenomenon. In the molten mass, solu-tion, or vapor, the molecules are in a state of rapid motion and frequent collision. When the temperature has fallen so far. that it is possible for a crystal to exist, a few col-liding molecules may fail to rebound, and so become at-tached to one another, the balance between the attracting and repelling forces-between them causing them to arrange themselves on a space lattice, to which other molecules sub-sequently attach themselves. It was once maintained that the X-ray evidence demanded that the molecule should dis-appear in the solid crystal, but this was a wrong inference, and in many crystals, but not in all, the chemical molecule retains its identity in the solid state. In pure metals the atom and the molecule are identical, so that the conditions are unusually simple. How many. nuclei will be formed in a given mass is evi-dently a problem in probability. Experiments to deter-mine the relation between the temperature and the number of nuclei formed in a given time have been made with some success by using viscous organic substances, but metals offer much greater difficulties, and the few determinations which have been published are vitiated by serious errors. However, the examination of sections of ingots of the same composition and cast at 'the same temperature in similar molds will show, that the number of crystals does not vary widely.

Jan 3, 1927

By E. P. McCurdy, W. J. Tait, A. E. Craig

The Circuitron herein described applies current from the classifier motor circuit and energy from the sound of grinding media to move an oscillating disc. The disc through a photoelectric cell controls the speed of the ore feeder and consequently the amount of ore delivered to the mill. THE Telluride Mines, Inc. at Telluride, Colo., is operating a flotation concentrator recovering lead, zinc, and copper with some gold and silver. The nominal capacity is 500 tons per 24 hr. The ore, which comes from several different mines, is characteristic of the district, changing from extremely tough rhodonite to soft gouge. The ore is crushed and washed, recrushed, and delivered to the mill bin at about % in. to serve as ball mill feed. Details of Grinding Circuit The material from the fine-ore bin is carried over a belt feeder driven by a Reeves vari-speed device. The belt discharges to a No. 86 Marcy ball mill, which operates in closed circuit, with jigs and a 6-ft Dorr classifier. A Massco density controller holds the density of the classifier overflow at a predetermined point. The overflow, which contains about 5 pct + 48 mesh, goes to the flotation section. Manual Operation Before the adoption of automatic control for the grinding circuit, this work was all done manually by the operator. The bin gate was set to deliver 40 to 50 lb of ore per lineal foot of belt, and the speed of the belt was adjusted by the operator to deliver at the rate of about 500 tons per 24 hr. As the ore changed in hardness, specific gravity, or in the amount of moisture, or, as the size of the feed changed due to bin segregation, crusher setting, or other causes, the operator made corresponding changes in the rate of feed by manipulation of the Reeves control. Sometimes these changes occurred so rapidly that they caused sharp, pronounced surges, which created very considerable unbalance from normal conditions in the grinding circuit and, more critically, in the flotation section. Since it is not possible for the operator to anticipate or follow such changes closely, a very considerable unbalance from normal conditions may occur, which will require a drastic change in the rate of feed. These surges upset the fineness of grind and interfere radically with the balance between tonnage and reagent control. All of this tends to reduce the grade of concentrates, increase the loss in the tailing, and thus decrease the recovery of values. The Circuitron Some years ago, The Mine and Smelter Supply Co., in conjunction with the operators at the Telluride Mill, undertook to build a device that would give close control of the rate of feed from the ore bin and to coordinate with this a related device that would regulate the amount of sand load on the classifier rakes. Emphasis was strongly laid on the fact that such a control must apply to the entire grinding circuit and must include the feed to the ball mill, the classifier sand return, and the density of the classifier overflow. If this could be done successfully, we felt that the circuit could be operated under best possible conditions, with compensations

Jan 1, 1951