Search Documents

By Robert Roberts

(Butte Meeting, August, 1913.) In order to obtain data on the thermal effect of the blast-furnace jacket and on the water consumption in these jackets a series of tests were run on the 56 by 180 in. blast furnaces at the Great Falls Reduction Department of the Anaconda Copper Mining Co., at Great Falls, Mont. The arrangement of the jacket is shown in the transverse section of one of the furnaces (Fig. 1) on which the tests were made. The nose, spout, and breast jackets have independent water supplies and discharges. The end and side jackets are connected in pairs, as regards water supply, the feed water entering at the bottom of the lower jacket and overflowing into the bottom of the jacket immediately above it, and discharging into an independent overflow pipe for each pair of jackets. Tests were run on the main side and end jackets, the breast jacket, the spout, and the nose. Measurements were taken of the quantity of water discharged, per minute and the rise in temperature of the water in its passage through the jacket. The product of these two results, expressed in the proper units, evidently gives the number of units of heat removed per minute by the water. Sufficient work was done on each type of jacket to determine its behavior under different conditions, and the results from each set of conditions were checked by repeating the work from three to six times. The method used was as follows : The overflow from the jacket to be tested was arranged to discharge at will into a barrel, mounted upon platform scales. The discharge temperature was read just before turning the water into the barrel, and just before turning it back to the sluice; if the test lasted more than a minute, additional temperature readings were taken at 1-min. intervals from start to finish. The elapsed time of running the water into the barrel was, determined with a stop-watch, and this figure, combined with the in-

Jan 7, 1913

By L. D. Wooddy, W D. Moore

Water drives may be natural or artificial. For the case of a natural water-drive reservoir, the volume of water influx corresponding to reservoir pressuve-production history may be calculated by means of the material bal-ance-unsteady state equation. For the artificial water drive or pattern injection water flood, the material balance equation is sufficient to determine the reservoir pressure-production, injection history. However, for both cases to reliably predict reservoir performance, it is necessary to calculate the saturation distribution of the reservoir fluids at different stages of depletion. This paper consolidates the various equations used to determine the performance of water-drive reservoirs into one approach that is applicable to any reservoir that has a natural water drive or is to be produced by water injection. The numerical procedure has been simplified considerably, and the solution is adaptable to either hand calculations or digital computer operation. INTRODUCTION A water-drive reservoir is one in which the predominant source of energy for production of oil results from the encroachment of water into the oil zone. The water drive may be either natural or artificial. Water invasion takes place by expansion of water in the aquifer as a result of the pressure decline transmitted from the oil reservoir. Because water is practically incompressible, a natural water drive requires an extensive aquifer containing a volume of water many times the volume of oil in the reservoir. Provided the permeability of the formation is reasonably high, a moderate decline of reservoir pressure usually causes adequate water influx. If the reservoir pressure decline becomes excessive because of low permeability or a high rate of production, part of the oil production may result from the liberation of dissolved gas which may cause excessive quantities of free gas to be produced along with the oil. In extreme cases, reservoir pressure may decline so rapidly as to cause the oil to be produced predominantly by dissolved gas drive, leading to abandonment of the reservoir before the advancing water has had a chance to flush the entire reservoir. In reservoirs that are not connected to extensive aquifers, an artificial water drive may be created by injecting water into or around the lower edges of a reservoir. Sometimes water is injected within the reservoir through wells interspersed among the producing wells. When injection is carried out in such fashion, the reservoir is in effect subdivided into a number of separate producing segments, in each of which the displacement of oil is simultaneously taking place, and the shapes of which are fixed by the well patterns employed. Because of the natural tendency of oil and water to segregate according to their relative densities, water will tend to migrate downdip regardless of where injected. Accordingly, the injected fluids can be retained within the intended reservoir segments only when conditions are unfavorable to their migration under the force of gravity. Pattern injections are usually confined, therefore, to reservoirs having low structural relief, or low permeability, or when production and injection rates are such that fluid movements in the reservoir are dominated by the pressure gradients rather than by the force of gravity. In the case of natural water-drive reservoirs and artificial water-drive reservoirs in which the water is in-

Jan 1, 1958

By C. L. Meyers, J. L. Lytton, T. E. Tietz

The recovery of tensile flow stress of 99.995-pct Al and Al-1 pct Mg alloy was investigated using a fractional recovery parameter. Tensile strainirg was conducted at room temperature, and recovery treatments were made in the range from 80° to 200°C. Equal values of fractional flow stress recovery were found to result in equivalent structural states. Identical recovery treatments were found to produce constant values of fractional flow stress re covery, independent of prestrain. The activation energy for recovery of the 99.995-pct A1 between 80" and 200°C was found to be 23,000 +2000 cal per mole, and the activation energy for the Al-1 pct Mg alloy was 27,500 cal per mole. 1 HE degree of recovery of a cold-worked metal may be studied by measuring the changes which take place in any of a number of properties. Some of the properties which have been used by past investigators include X-ray diffraction phenomena, electrical resistivity, hardness, creep strength, elastic limit, and flow stress. Despite the apparent preponderance of such studies, little is known concerning the effect of recovery on the strength of metals except as deduced from changes in various types of hardness measurements. Furthermore, little information is avail- able concerning the effects which specific solute atoms have on the recovery process. Limited studies have indicated that in some cases solid-solution additions greatly decrease the rate of recovery,' whereas in at least the case of magnesium additions to alluminum an increase in the rate has been reported.2 The purpose of this investigation was to determine the effect of a 1 pct Mg addition on the recovery of high-purity aluminum. Because of the particular interest in the effect of solute additions on the recovery behavior as related to mechanical properties, the degree of recovery was evaluated in terms of tensile flow stress. For the purposes of this study, a recovery process shall be defined as any process, short of recrystallization, whereby the properties, of work-hardened metals tend toward their values ill the unstrained state. EXPERIMENTAL PROCEDURE Test Materials. The materials used in this study were a 99.995-3 A1 and an Al-1 pct Mg alloy made from high-purity base metal. The high-purity aluminum contained the following wt pct impurities: 0.001 pct Cu, 0.002 pct Fe, 0.001 pct Si, and 0.0004 pct Mg. The Pil-1 pct Mg alloy contained 0.001 pct Cu, 0.002 pct Fe, 0.003 pct Si, and 0.99 pct Mg. Both materials were obtained in the form of as-rolled 0.125-in.-thick sheets, from the Alcoa Research Laboratories, New Kensington, Penn. Tensile specimens were cut from these sheets with the longitudinal axis in the rolling direction. Both materials were recrystallized in a molten salt bath; the high-purity aluminum at 450° C for 20 min and

Jan 1, 1962

By T. Leffers, A. Grum-Jensen

The development of texture in copper and brass (15 pct Zn by weight) rolled at room temperature and in copper rolled at -196°C has been followed by determination of pole figures for various degrees of reduction. The concurrent development in microstructure has been investigated by transmission electron microscopy. For low deformations, the texture in brass, and in copper rolled at -196°C, is the same as the texture in copper rolled at room temperature. The difference in texture does not show until 50 pct reduction. At the same reduction at which the difference in texture appears, mechanical twinning starts in brass and low-temperature rolled copper. Nevertheless, Wassermann's twinning theory is found to be incompatible with the present resulls. All fcc metals and alloys develop, by heavy rolling, one or the other of two types of texture, classified for convenience as copper type and brass type, or possibly a '(mixed" texture representing an intermediate stage between the two types. The pure fcc metals, except silver, develop copper-type texture by rolling at room temperature. Silver and many alloys, including brass with more than 10 pct Zn, develop brass-type texture.' By rolling at low temperatures a transition in texture from copper type to brass type has been observed for copper of commercial purity.2'3 It is generally accepted that there is a correlation between the type of texture developed and the stacking fault energy. Metals and alloys having fcc structure develop brass-type texture when rolled at room temperature if the stacking fault energy is low, whereas those with higher stacking fault energies have copper-type texture.2 Thus, the difference in stacking fault energy must cause a difference in deformation mechanism responsible for the difference in texture. Of the numerous theories advanced concerning the nature of this difference in deformation mechanism, four seem to be of current interest. Smallman and Greeen,2 Dillamore and Roberts,4 and Dillamore5 refer to the fact that cross slip more easily takes place in a material with a higher stacking fault energy and suggest that the copper-type texture is developed by deformation with extensive cross slip whereas the brass-type texture is developed by deformation without cross slip. Haessner6 has advanced the theory that the copper-tye texture is developed by a combination of normal {111} slip and slip on other planes, mainly 1100). Thus his theory, like the theory above, proposes an additional deformation mode for the formation of the copper-type texture. Contrary to this, wassermann7 and Ahlborn et al.8 believe that the copper-type texture is obtained by normal slip. In their opinion mechanical twins will change a copper texture into a brass texture. For this reason it is suggested that the brass-type texture is developed when, in addition to normal {111}(110) slip, mechanical twinning is present. None of these theories are, however, supported by direct experimental evidence. In a recent experiment Hu et al.9 have followed the development of rolling texture in copper and brass. The texture of copper and brass was found to be es-

Jan 1, 1969

By C. H. Gorski

A method for preparing titanium tetrachloride is described which consists of reducing rutile with coke and chlorinating the reduced product at 200° to 500°C. The crude distillate is purified by treatment with copper powder and distillation. Recoveries, exceeding 90 pct of the titanium in the rutile, were obtained. IN recent years considerable interest in metallic titanium has been aroused because of its outstanding physical and chemical properties. The present commercial processes for preparing titanium are modifications of the Kroll1 process and consist essentially of the reduction of titanium tetrachloride with magnesium in an inert atmosphere to produce metallic titanium with magnesium chloride as a byproduct. At present,' commercial titanium tetrachloride costs $0.32 a pound, which makes the price of the included titanium $1.28 a pound. As the titanium tetrachloride must be purified further before processing into metal, its ultimate cost obviously will be higher. Consequently, one of the prime requisites for the production of lower cost titanium metal is a source of low-cost titanium tetrachloride. Recently, Knickerbocker, Gorski, Kenworthy, and Starliper3 escribed a method for preparing titanium tetrachloride from low-grade Arkansas rutile by smelting the rutile with pyrite and coke to form a titanium matte and then chlorinating the titanium matte to prepare a crude titanium tetrachloride. This process had several inherent advantages. Low-grade rutile concentrates were utilized, the chlorination temperature was relatively low (approximately 200°C), and the reaction was strongly exothermic. However, this process had several disadvantages, chief of them being the rather low recoveries of titanium tetrachloride (65 to 81 pct) and the difficulty in purifying the crude titanium tetrachloride obtained. Because of the high-titanium and low-iron con- tents of rutile as compared to ilmenite, rutile should be of greater potential value as a source of titanium tetrachloride than ilmenite. Rutile, however, is not chlorinated directly in commercial practice, because reaction temperatures above 700 °C are required, at which point chlorine attacks most of the common materials of construction. The process now in use consists of converting the titanium in rutile to the cyanonitride by high-temperature reduction in an electric furnace, and then chlorinating this compound. The disadvantages of this process are the difficulty of producing the cyanonitride, the use of high-grade rutile concentrates in the charge, and the presence of several percent of silicon tetrachloride in the finished product. It would be of considerable interest to develop a new process for the preparation of titanium tetrachloride from rutile by chlorination at 200" to 500°C. Process Development Several investigators'-' have studied the reduction of titanium dioxide with carbon in an effort to prepare titanium monoxide. Invariably, the titanium monoxide formed in this manner was not pure, as it contained titanium carbide and one or more of the lower oxides of titanium. As these lower oxides of titanium are more reactive chemically than rutile, and as it is known that titanium carbide may be chlorinated readily, a study was made of the chlorination of carbon-reduced rutile. A sample of rutile concentrates from Hot Spring County, Ark., containing 76.19 pct TiO,, 5.65 pct Fe2O3, 4.18 pct SiO2, and 2.88 pct Al2O3, was used for this investigation. The experimental procedure consisted of making an intimate mixture of —100-mesh rutile and petroleum coke, adding water and molasses as a binder to foi-m a paste, charging into a graphite crucible that was covered, except for a vent to allow the

Jan 1, 1952

By Pedro L. Lizaur

INTRODUCTION The degree of success of an association between parties in establishing a new venture ultimately depends on three factors: a. the venture's underlying economic strength, which is based on the complementarity of the comparative advantages brought by each party to the negotiating table; b. the ability to reach an agreement which satisfies each party's objectives and constraints; and, c. the capacity to design and implement a funding structure which is consistent with the project economics. A thorough assessment of the venture's profitability and associated risks under alternative technical and economic scenarios is the basis for a sound "go" or "no go" decision. In-depth evaluation of the risks and rewards to each of the parties involved under alternative legal and financial structure must be the foundation for a long lasting "how to go" decision. The allocation of risks and rewards should be consistent with the objectives and constraints of all parties and the sharing mechanisms, established in the contract, should be flexible to assure the long-term stability of the agreement. Rapidly changing economic conditions during the last decade have had a dramatic impact on the envisaged allocation of risks and rewards between host countries and private investors. The effects of these changes, and the fact that the relative strengths of the parties involved may shift during the life of a project (e.g. before and after major capital investments have been made), have forced the renegotiation of a multitude of contracts. Therefore, the present and future stability of an economic agreement would depend not only on the originally designed provisions, but also on provisions which allow for the automatic adjustment of rewards to project sponsors under a variety of future economic situations. A pre-condition for the allocation and quantification of risks and rewards is the definition of standards of measurement used by each of the parties. This is critical in international negotiations when one of the parties represents the national interests of a country. The understanding and use of different standards for the measurement of rewards for risk taken between a government and private enterprise facilitate the negotiation of a satisfactory agreement. This is possible because certain trade-offs between the negotiating parties may have different relative values. STANDARDS OF MEASUREMENT OF REWARDS FOR RISK TAKEN The negotiating process takes a step forward when the parties are able to focus on their interests, explore different alternative solutions and then base results on a set of objective standards. Unfortunately, the parties frequently put more effort into "staking out" and defending positions, than into understanding their intrinsic interests. Moreover, when one party, such as a governemnt owned corporation, represents a country's national interests, the negotiation process increases in complexity. Private firms focus on commercial profitability, using discounted cash flow techniques such as NPV, IRR, or ROE. In contrast, the government is also concerned with the project's impact on the local socio-economic environment. Without entering into a discussion of alternative economic development theories and approaches, there exist several possible measures that could be pragmatically utilized by each party in evaluating the socio-economic impact of a project. The more complete measure is the National Profitability (NP). The NP is a discounted cash flow procedure similar in structure to IRR or NPV but in which the project's financial cash inflows and outflows and discount rates are adjusted to take into consideration the local conditions. The NP is calculated on an unlevered basis and all taxes and duties are removed from the project

Jan 1, 1985

By Walter R. Hibbard, Harold Margolin

The effect of ten ternary additions on the aging of a Cu-Ag alloy was measured by X ray, microstructure and hardness. A supersaturated copper-rich transition structure was found. The effect of the ternary element was related to differences between transition and precipitate lattice parameters and analogies with solution and strain hardening. IN addition to the prerequisite of diminishing solid solubility with falling temperature, the theory of coherency hardening1 proposes that the principal source of hardening during precipitation is strain caused by coherency between the matrix and precipitate. For a given system greater coherency hardening would result from lengthening the period of coherent growth and/or increasing the number of nuclei, other things remaining equal. However, the hardness change during aging is a function of a number of phenomena in addition to coherency hardening, such as dispersion hardening, loss of coherency, solute depletion, matrix recovery or recrystal-lization, coalescence, and their relative time sequences. The present investigation was undertaken to study the effect of ternary additions on the age-hardening of Cu-Ag alloy. For this purpose a series of alloys were made containing as ternary constituents Mg, Al, Si, P, Mn, Ni, Zn, As, In, and Sb. These elements were added to a master 5 wt pct Ag in Cu alloy in such amounts as to obtain alloys listed in Table II containing the following approximate atomic percentages: 96 pct Cu, 3 pct Ag, 1 pct ternary addition. A 97 atomic pct Cu, 3 atomic pct Ag alloy was used as a comparison standard. There have been numerous investigations of age-hardening in Cu-Ag alloys2-lo but few of ternary Cu-Ag alloys. Pfister and Weist" found that 1 wt pct Ni reduced the solubility of Ag in Cu above 600 °C and that the rate of precipitation was slower than in polycrystalline Cu-Ag alloys of similar silver content. More recently Hodge, Jaffee, Dunleavy, and Ogden12 investigated the effect of ternary additions of Mg, Li, P, Cd, Zn, Zr and Be on strength properties of Cu-Ag alloys. Mg, Cd, and P were found to increase strength in the aged and cold-worked condition. Experimental Procedure Charges weighing 7.5 lb were melted in a closed carbon crucible under a reducing atmosphere* of nitrogen and hydrogen. A Durville-type casting procedure with a hot-top arrangement was used to obtain a sound casting, 2x2x43/4 in. Prior to rolling and annealing of the ingots, a trial solution anneal of rolled sections of the hot-top portions indicated that at 780°C melting was avoided except for the Cu-Ag-Sb alloy. This alloy could not be produced as a single phase within the limits of temperature control. i 3" to 5oC, since melting occurred at 64O °C, and below this temperature precipitation was

Jan 1, 1952

By J. E. Johnson

THE production of metal-working tools has been revolutionized within the last 18 years, since the invention by Taylor and White of a process of heat-treating steel tools, which resulted in increasing their cutting capacity several fold over what it had been before. This was an exceedingly important invention, although it consisted principally, in establishing this fact overheating when it accidentally, occurred in the ordinary:-process of forging, spoiled the steel, but if carried very much farther or to-a point that would have been considered absolutely ruinous to the steel under the old ideas, it resulted in imparting a cutting power several times as: high as had ever been obtainable before. The quality that gives the steel this power eventually received the name of "red hardness." This name originated in the fact that tools possessing this property retain their resistance to deformation even when subjected to, such severe cutting stresses that the metal just back of the point is heated, under certain conditions, to a visible red. It is interesting in this connection to note that the edge of the tool itself does not become red because it is continually cooled by the fresh metal into which it is forced. The result of Taylor and White's invention was an intensive study, of tool steels all over the world and, although there was-great diversity of analysis in the high-speed steels of the early days, these steels today generally have an approximately similar composition, the principal constituents being froth 15 to 20 per cent. of tungsten, from 4 to 6 percent. of chromium, from 1 to 2 per cent. of vanadium, and from 0.50 to 1 per cent. of carbon. It is probably safe to say that standard brands of such high-speed steels will do from five to ten times as much work in a given time as the carbon steels, and even the Musket steels, which were the sole dependence up to the beginning of this century, when the Taylor-White process was discovered. With the increasing cost of labor, it is not surprising that these steels have driven froth the market, for all but limited purposes, the older types of steel.

Jan 2, 1919

By H. G. Schneider

The Smackover oil and gas field lies in Ouachita and Union Counties, Ark., in the south-central part of the state, in T.15 and 16S., R.15, 16, and 17W. It is 10 miles north of El Dorado, the principal business and railroad center in the south-central part of the state, and extends from the town of Smackover in all directions. Productive territory having an aggregate area of nearly 55 sq. mi. has been developed. It extends 6 miles from north to south and 12 miles from east to west. The field may be divided into two parts: the east district, which includes the area east of the town of Smackover, and the west district, which includes the area west of the town of Smackover. In relation to the neighboring productive fields of Arkansas, the Smackover field is 9 miles north of the El Dorado oil and gas field, 8 miles slightly west of north of the East El Dorado oil and gas field, and 16 miles east of the Stephens oil field. Smackover was discovered in May, 1922, when the Oil Operators Tnist drilled well No. 1 on the J. T. Murphy farm, in the southeast quarter of sec. 8, T.16S., R.15W. This well is located almost on the top of the Norphlet dome and was drilled to the Nacatoch sand. It had an initial open flow volume of 30,000,000 cu. ft. of dry gas per day, and a rock pressure of 950 lb. per sq. in. In July, 1922, the V. K. F. Co. completed the first oil well in sec. 29, T.l5S., R.l5W., on the north side of the Norphlet dome, and 3 miles north of the first gas well. This well started the active development of the north and northwest sides of the dome.] The field was extended westwards, when oil was discovered in the Nacatoch sand, during October, 1922, in sec. 4, T.l6S., R.l6W., 51/2 miles west of the original gas well. This opened up the so-called "light oil district," which is located on a structural terrace, for which the name

Jan 1, 1924

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.' So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer's surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By G. F. Jr. Butterworth

THE metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to produce in the stock a physical condition having the requisite properties. The first group consists 'of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat-treated by giving it a quench and a draw. These barrels will be referred to as "heat-treated" barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent. of manganese, show a single very pronounced point between 1300° and 1350° F. (704° and 732° C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure discussed below, Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure, shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under- a low magnification appears

Jan 7, 1919

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation' indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in' all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest 'Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation' indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in' all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest 'Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By J. M. Roberts, N. Brown

The stress-strain behavior of zinc single crystals was measured over a strain range of 10-6 to 10-2. The phenomenon of macroyielding was observed in detail and plastic strains were detected at almost zero-stress. Closed hysteresis loops were observed during loading and unloading in the strain region of about 10-5. From the hysteresis a frictional stress on the dislocation of about 6 psi was obtained. A preliminary analysis indicates that impurities are primarily responsible for the friction. Nonelastic Strains as much as 10 -4 were recovered depending on the amount of prior deformation. Part of the recovered strain occurs instantaneously upon unloading and the remainder occurs at zero stress. The time dependence of the recovered strain was measured. THIS investigation is concerned with the details of plastic deformation preceding the ordinary yield point as measured with the usual strain sensitivity of about 10-4. The approach leads to internal friction observations in the hitherto neglected frequency range below 10-1 cycles per sec. It is believed that if the phenomenon of macroscopic yielding is to be understood, then the stress-strain curve in the neighborhood of the macroyield point should be greatly magnified. It may then be possible to determine whether macroscopic yielding is a unique event or whether it is a process which begins gradually at a lower stress. In the case of low-carbon steel a unique event obviously occurs at the macroscopic yield point as indicated by a drop in the load, but copper appears to exhibit a gradual transition from the elastic to the plastic state. In zinc the yield point is rather abrupt although the data indicates that some plastic deformation precedes large scale yielding.' One of the purposes of this investigation is to determine whether there is an abrupt transition from the preyield microstrain region to the region of macroscopic deformation. Such a rapid transition would support the concept that there is a critical stress for yielding. The concept that yielding is a unique event associated with such phenomenon as activating a Frank-Read source, freeing the dislocation from solute atoms, dislocations cutting through dislocations, or dislocations moving freely by one another, has been expounded widely on theoretical grounds. It is hoped that highly sensitive measurements of strain in the neighborhood of the macroscopic yield point will shed some light on the event known as the "Yield Point". EXPERIMENTAL METHOD 1) Specimens—High-purity zinc was cast into spherical graphite moulds in air and grown into spherical single crystals by the Bridgman method under a positive pressure of Argon gas. Spectro-graphic analysis of cleaved sections from four crystals showed a purity of 99.994 pet Zn. The specimens were acid machined with an 1/8 in. gage section in a form similar to those used by Parker and co-workers.2 Bausch type grips were fastened to the specimen by Epon VI adhesive. The specimens were oriented so that only [1120] (0001) slip occurred. Fig. 1 shows two of the specimens in the grips. Prior to each test, the gage section of the specimen was given a concentrated HNO3 chemical polish followed by alcohol rinsing and air blast drying. 2) Test Method- The shear tests were performed on an Instron testing machine and the experimental set-up was made very "hard". Strain could be measured to a sensitivity of 10 -6 by means of a capacitance gage extensometer. The design and calibration of this type of extensometer to measure microstrain, as applied to pure shear and tensile tests of metals, will be the subject of a separate paper—therefore, only a brief account will be presented here. The method essentially consists of attaching a

Jan 1, 1961

By R. M. Rose, D. P. Ferriss, J. Wulff

Single crystals of tantalum, tungsten, and the binary alloys thereof were grown by electron-beam zone melting and tested in tension between 77° and 373°K. The ductile-to-brittle transition temperature increased sharply with solute concentration, for both tungsten-rich and tantalum-rich alloys; apparently, the maximum transition temperature exists near the 50 pet concentration. Twinning was observed to be a consequence of cleavage-crack propagation. Cleavage occurred on(100)planes, and extensive tearing and "river markings" were present. The onset of brittleness could not be associated with any change in deformation mode, the yield point phenomenon, or the large rise in yield stress with decreasing temperature. Cleavage was observed to initiate at either the specimen surface, or subgrain boundaries. The observation was made that the grain boundaries of Polycrystalline materials are probably even better as nucleation sites for fracture, and are responsible for brittleness at high temperatures and lower solute concentrations than those of the corresponding single crystals. TUNGSTEN and tantalum, the two high-melting neighbors in the third transition period of the periodic table, present striking contrasts. Although both are bee, tungsten has far higher elastic moduli, and the highest ductile-to-brittle transition (DBT) of all the pure metals.' Tantalum, however, is ductile at liquid helium temperatures. Large strain aging and yield point phenomena are observed in tantalum,2,3 but only to a lesser extent in tungsten.4 Tungsten work-hardens at a high rate,5 whereas this effect is negligible in tantalum.' Since the mutual solid solubility of these two metals is complete,7 and no ordering has yet been reported in the binary system, the possibility of depressing tungsten's DBT by tantalum additions was considered. Also, tungsten additions to tantalum could produce hard, high-melting alloys which might be ductile at room temperature. Such alloys offered excellent bases for complex alloy development, particularly with regard to the effect of rhenium on Group VI metals.8"10 In addition, there was the opportunity to examine flow and fracture modes in the vicinity of the DBT, with particular emphasis on the correlation between brittleness and fundamental deformation mechanisms. Myers11 has reported that recrystallized alloys with up to 10 pet W in tantalum are ductile at room temperature, but alloys with 20 pct W could not be swaged at temperatures as high as 500°C. The whole spectrum of Ta-W alloys has been surveyed by Braun, Sedlatschek, and Kiefferl2 using sintered powder compacts. In addition to some physical properties they reported a maximum hardness at about 50 at. pet W, dropping to much lower hardness levels for the pure components. They were able to cold work tantalum-base alloys with as much as 30 pet W and to warm work tungsten-base alloys with up to 20 pet Ta by procedures similar to those used for pure tungsten. EXPERIMENTAL In order to study deformation modes and to keep the impurity concentrations at a minimum, electron-beam zone melting was used to prepare single crystals of high purity. The electron-beam zone melting apparatus is similar to that described by Calverley, Davis, and ever" and incorporates a grid control rectifier to maintain control of emission current. Pure metals were refined by making three zone passes at 4 mm per min up the rod. Alloys were prepared by melting together wire of one constituent on a previously melted rod of the major constituent. Subsequently, two zone passes were made in opposite directions to level the composition after the manner suggested by pfann.14 Purification of the starting materials was accomplished by evaporation of the several impurities, and the degree to which this was accomplished is indicated in the chemical analyses of Table I. The uniformity of composition along a zone levelled rod was within the i 1 pet accuracy of the fluorescent X-ray technique used to determine composition. Crystallographic orientation of the

Jan 1, 1962

By Elton A. Youngberg

The Holden mine operated by the Chelan Division of the Howe Sound Co. is on the east slope of the Cascade Range in north central Washington on the south slope of Railroad Creek valley at an elevation of 3500 ft. The mine may be reached by a 40 mile boat trip from the town of Chelan which is at the southern tip of Lake Chelan, to Lucerne at the mouth of Railroad Creek and an 11. mile bus ride up Railroad Creek to Holden. A11 freight and concentrate is moved over this route to Chelan Falls on the Columbia River which is on the railroad four miles below the town of Chelan. The mine is now producing 2000 tons of gold, copper, and zinc ore per day which is treated in the Holden mill. Gold-copper and zinc concentrates are made, the first of which is shipped to Tacoma, Wash., and the latter to Kellogg, Idaho, for smelting. Ore is broken by long-hole blasting using the Noranda system which has been modified to meet local conditions. Until recently, blastholes have been drilled by diamond drills. Now a partial substitution of percussion drill holes, drilled with tungsten carbide insert bits, is being made. Geology The ore body occurs as a replacement deposit in a highly metamorphosed series of sedimentary rocks, mainly gneiss and schists, in a shear zone several hundred feet in width and of undetermined length. Commercial ore has been found in mineable widths of 25 to 100 ft for approximately 2500 ft along its strike. The commercial minerals are chalcopyrite, sphalerite, and gold. During the period of mineralization considerable silicifica-tion took place giving the ore an abrasive drilling characteristic. Following the period of mineralization, numerous dikes were introduced into the ore body. The earlier ones were of granite composition having a width of a few inches up to 80 ft. These were followed by much younger, fine grained basic dikes which usually do not exceed 2 ft in width. Development of Percussion Blasthole Drilling Equipment Test work with the 1½-in. tungsten carbide bit was carried on in development headings for several months early in 1947. The short life of the bits, because of gauge loss caused by the abrasive nature of the rock, prevented its adoption for this use. However fast drilling speed and ability to drill a long uniform hole suggested its use for drilling blastholes in competition with diamond drills as diamond costs were steadily increasing and exper-ienced drillers were difficult to obtain. The 1½-in. bit was the largest available at the time initial test work was started with sectional steel. The 1½-in. hole limited the diameter of the steel thread and coupling which could be used. Type F couplings were first used but because of the small thread section excessive breakage of the steel was experienced. Type H couplings were tried next. In order to use this coupling which is 15/8 in. in outside diameter, it was reduced to 1 3/8 in. giving 1/8 in. clearance between the coupling and the hole. Rod breakage at the thread was substantially reduced but some coupling breakage was experienced, however the overall performance was considered satisfactory (see Fig 1 for illustration of coupling and thread). Early test work with the 1½ in. bit indicated machines of piston diameters larger than 255 in. would cause inserts to loosen or break. It was found however that the additional weight of the sectional steel cushioned the blow enough to prevent bit failures when 3-in. Leyners were used. Rods used with the 1½-in. bits were 7/8 in. q. o. for sectional steel and 1 in. q. o. for all chuck pieces. In May 1948, 2-in. tungsten carbide bits became available and test work was immediately started. The 2-in. hole approximated the AX (1 15/16 in.) diamond drill hole which was being used exclusively for blastholes and permitted their substitution for diamond drill holes in a ring without alteration of pattern, burden, or explosives. The 2-in. bit also gave room in the hole for larger couplings and permitted the use of heavier rods and 3½-in. machines, increasing the

Jan 1, 1950

DEVELOPMENT of a chemical process for the extraction of pure metals from mill concentrates or metal scrap has progressed beyond the pilot plant stage and may prove an important adjunct to present smelting and refining methods if initial commercial operations prove economically successful. Developed by the Chemical Construction Corp., the new process involves the treatment of oxide and sulphide ore concentrates by chemical methods, instead of the usual smelting and refining techniques. Several of the many applications are now scheduled for commercial use. Refiners using the new process will prepare ore concentrates by standard flotation methods, introduce the concentrate as a slurry into an autoclave along with water and an acid or ammonia. From the resulting leach solution, recovery of individual metals is made by use of suitable reducing agents. By varying conditions during treatment, different metals in the ore are produced separately as pure powders, which may be pressed into forms ready to market, or in the case of copper, extruded as rods or pipe. The reagents are generally recovered. By manipulating the variables during reduction, selective separation of nickel, and/or cobalt, and/or copper can be made simultaneously. The separation is a continuous operation. Low metal prices are not immediately in view because of the tremendous demand at this time. However, reduced metallurgical treatment costs will allow economical mining of orebodies with lower metal content, permitting increased production to meet demand. Although the practical horizon for use of the new process appears to be limitless, one factor may enter into its employment. Just how low grade a concentrate can be economically used is unknown. In addition, for present practical considerations, only metal below zinc in the electromotive series may be processed. Each commercial application requires specific technique adaptation and pilot-plant data for engineering design. A nickel-cobalt-copper process has been researched and piloted in collaboration with Sherritt Gordon Mines, Ltd., for the firm's Lynn Lake properties. In addition, processes were tailored for cobalt concentrates of Howe Sound Mining Co., and National Lead Co., in view of the urgent need for this specific metal. Major General William N. Porter, president of Chemical Construction, says of the new process, "piloting experience has shown that production cost, from ore concentrates to pure metals should be considerably below current costs." Other savings may be realized by cutting transportation and personnel costs, and by reducing the time lag between mining and pure metal from months to a matter of hours. First commercial use of the process will start sometime this summer. Chemico is slated to finish building a $2.5 million cobalt refinery for Howe Sound Mining near Salt Lake City. The plant is expected to raise world cobalt production by 40 pct. The plant will process 35 tons of 20 pct cobalt concentrates from Howe Sound's Blackbird mine near Cobalt, Idaho, daily. Yearly production is expected to reach 2000 tons of pure metal, about one half of U. S. consumption in 1950. Steps in the Howe Sound application of the process are: 1. Acid oxidation leach. 2. Filtration (residues thrown away are insoluble compounds-gangue, iron, arsenic). 3. Cementation (for Cu removal because Cu content is too low for recovery). 4. Reduction from ammoniacal solution. 5. Separation of Co and Ni as mixed metals (95 pct Co and 5 pct Ni). 6. Recovery of ammonium sulphate. Under construction at the Fredericktown, Mo., mine of National Lead is a $5 million refinery sched- [ ]

Jan 1, 1952