Search Documents

By R. T. Webber, R. B. Owen

The vapor phase deposition of molybdenum and tungsten from the hexacar-bonyls has been thoroughly investigated by Lander and Germerl, and shown to yield well-bonded coatings on a variety of hot metallic surfaces. They also demonstrated that chromium coatings2'3 could be similarly deposited, but did not investigate this metal extensively. Recently, conditions have been described by which this compound can be prepared in quantities sufficient for laboratory scale plating experiments, and it is the purpose of the present communication to outline the results of preliminary experiments upon the plating of chromium from its carbonyl. Apparatus and Technique The apparatus used in these experiments is shown in Fig I. At one end, connected by a short length of rubber tubing, is a Cenco Hypervac 20 pumping continuously. At the opposite end is a needle valve which allows a small stream of purified hydrogen to flow through the apparatus. Connected in series are a trap T1, maintained at the temperature of dry ice and acetone, the plating chamber, and two traps T² and T3 containing crystals of the carbonyl. T² is kept in a constant temperature bath (not shown), while T³ is at room temperature. Stopcock S6 allows the hydrogen flow to by-pass the carbonyl traps. A McLeod gauge is connected so that it can measure the pressure at the pump through Se, or the pressure at the plating chamber through S9 and S6. The standard (12 liter) volume connected by Sb is used to determine the volume included by S4, S6, SB, Slot the needle valve and the McLeod gauge. Knowledge of this volume allows calibration of the flow of hydrogen. The apparatus* is built entirely of pyrex, except for the needle valve, the rubber connection to the Hypervac, and the cover of the plating chamber. The plating chamber is water-jacketed, with a large brass top allowing insertion of the specimen to be plated. Set into the brass top is a ground glass stopper through which thermocouple leads are sealed. The thermocouple wires (pure Pt, and 87 pct Pt-13 pct Rh) serve the double purpose of measuring the specimen temperature and suspending it in the chamber. Surrounding the chamber is the coil of an induction heater, H. The apparatus is designed to allow variation of the following conditions: (I) the specimen temperature, from room temperature to about 1000°C, (2) the carbonyl vapor pressure, from 40 to 220 microns, and (3) the hydrogen flow. In several runs, 0.8 to 1.8 PCt of hydrogen sulfide was introuced through a needle valve that replaced S4. The vapor pressure of the carbonyl is

Jan 1, 1949

By A. Madrazo

The Standing-Katz method for predicting liquid densities of reservoir fluids has been tested using experimental data of 154 bottom-hole or recombined reservoir fluid samples. New pressure- and temperature-correction curves for the Standing-Katz type correlation are presented which improve the accuracy of prediction. INTRODUCTION The present study was undertaken to investigate the known methods of determining liquid densities and to select one of them which might yield a better correlation if additional data were employed. An appropriate correlation would incorporate the following characteristics: (1) ease of handling in the computations, (2) results within engineering accuracy and (3) data easily accessible. After careful investigation of the different methods, the Standing-Katz correlation1 appeared to have these characteristics. The Standing-Katz correlation for liquid densities of hydrocarbon systems is based upon limited data. The original work, which employs apparent densities for methane and ethane, was based on data of 15 saturated crude oils in equilibrium with natural gas. Therefore, a test of the correlation using additional experimental data would serve either to validate the Standing-Katz correlation or to form a basis for corrections if such were necessary. PROCEDURE AND GRAPHICAL SOLUTION The data of 154 bottom-hole or recombined reservoir fluid samples were employed to calculate the densities at 14.7 psia and 60°F by the method described in Table 1. Volume contributions for methane and ethane were assigned from the pseudo liquid density plot (Fig. I), but volume contributions for N2, CO2 and HzS were not considered. The densities computed at reference conditions of 14.7 psia and 60°F were then elevated to their respective temperatures and pressures by the use of the correction curves proposed by Standing.' The percentage differences between the experimental values and the calculated values were determined; these samples were grouped into temperature, pressure and density ranges to determine a possible trend. It appeared that, at temperatures above 160°F, the calculated density values were consistently larger than the experimental density values; however, no obvious trend was found for the density and pressure ranges. There is a relationship between the pressure-correction and temperature-correction curves. This relationship, embodied in the temperature-correction curve, can be expressed as follows. The experimental densities of 125 samples above their bubble points were known. From these isothermal data, it was possible to determine an experimental-density difference between two pressures; and (from Fig. 2*), a calculated density difference between the same two pressures was determined. The relative effect of temperature must be considered in the calculated-density values. The effect of temperature can be determined by entering Fig. 3* at the two densities in consideration and obtaining the change in density at constant temperature. This change, or delta density, must be added

By F. von Gemmingen, E. J. Fasiska, L. Zwell

EARLIER studies of the dependence of creep on structure1 and of the dependence of creep rupture on creep behavior2 did not include detailed discussion of the phases present in the specimens under examination. It is of interest to determine the nature and amounts of such phases present since it is well known that these are dependent on composition, heat treatment and creep conditions.3 This investigation has therefore been undertaken to identify these constituents and to determine their relative amounts. This report presents the results of this investigation and describes an improved "extraction replica" technique developed in the course of the work. The composition of the Type 316 austenitic stainless steels studied in this investigation is given in Table I. The specimens were solution treated at 2000°F for 1/2 hr and water quenched. Those specimens subjected to prestrain at room temperature Methods for extracting precipitate particles from materials for electron and X-ray diffraction analysis have been described by Fisher,4 Smith and Nutting: and Booker and coworkers.6'7 Electrolytic extraction methods have been described by Andrews and Hughes.8 The first two methods have been used at this Laboratory, but have not proved satisfactory for many problems requiring X-ray diffraction analysis. It has been difficult to remove the replicas or to avoid tearing them during removal. These difficulties are overcome by backing the replica with a water-soluble plastic such as Dupont 51-05 Elvanol (polyvinyl alcohol). The backing increases the thickness of the replica so that it can be mechanically stripped from unloosened particles without folding or tearing. This procedure eliminates the stripping of wet replicas, which usually have a low tear strength. By stripping replicas after drying, it is possible to extract partially loosened particles which otherwise would remain imbedded in the metal. The modified method is as follows: after the specimen is polished, it is etched for 60 min in modified glyceregia consisting of 30 ml glycerol, 7 ml nitric acid, and 4 ml of hydrochloric acid. The sample is then washed, air dried, and coated with a 20 pct Baker and Adamson 1611 collodion (85 pct amyl acetate by volume) film. After the collodion film is dry (about 15 min), the sample is again etched in the modified glyceregia for 50 min, washed with isopropyl alcohol (to prevent dissolving the collodion) and air dried. A very thick coat of polyvinyl alcohol (about 50 pct solution "Elvanol Dupont 51-05" in water) is poured over the sample and is permitted to dry for about 24 hr. The composite film containing the precipitates is then stripped from the specimen and floated, polyvinyl alcohol side down, in water (at about 50°C) until the polyvinyl alcohol dissolves. This usually takes about 15 min. Should any of the polyvinyl alcohol remain on the replica, it does not give a crystalline diffraction pattern and therefore does not hinder identification of the precipitates. The extraction replica, floating in water, is picked up on a glass fiber and mounted in the Debye-Scherrer camera for X-ray diffraction analysis. Concentration of the etchant, and also etching time, had to be increased for several of the samples. Fig. 1 shows two extraction replicas taken from different areas of spec. M74-37; X-ray analysis showed a strong diffraction pattern of M23C6 and a medium one of u phase. A

Jan 1, 1962

By W. H. Moore, E. T. Powell

IN the early days of mining in the Anthracite field, only the thicker and better seams of coal were mined, because of the limited mining and coal-cleaning facilities, therefore many of the thinner and less productive seams were permitted to remain unmined. With improvements in mining methods, the introduction of modem preparation plants, and the increased market demand for small-size coal, the thinner and more laminated seams have now become assets. In many instances these seams overlie the mined-out beds of the thicker and better seams, from which all recoverable coal was removed by the conventional breast-and-pillar method of mining. Some collieries in certain sections of the Anthracite field are now relying on these thinner and laminated seams. For the purpose of illustration, a large area in the Hickory Swamp-Ridge Basin of the western middle coal field has been selected, where as early as 1898 the No. 4, or Little Buck Mountain, seam was mined and pillars removed. The No. 5, or Buck Mountain, seam lying on a comparatively light pitch and with intervening strata of but 55 ft. of rock was not mined until 1935. Farther east, in the same basin the Nos. 8 and 9 seams, which are two splits of the Mammoth seam, have been mined and robbed and the workings have been abandoned since 1896. The overlying No. 9½ seam, or the upper split of the Mam- moth, and the No. 9¾ or 4-ft. seam remained virgin, with only an interval of 50 ft. of rock separating them, and with 40 to so ft. of rock strata separating the No. 9½ seam from the completely mined area of the Nos. 8 and 9 seams. These seams lie on a pitch of 45° on the south side of the basin and on 75° on the north side of the basin. Mining has been carried on in the 9½ and 9¾ seams for 3 years on both dips of the basin, for a distance of 3500 ft. In some sections the overlying strata of the thicker seams previously mined have settled without any apparent breaks in the upper strata, as indications have shown in the top split of the Mammoth; while in other areas the roof and bottom of this top split of the Mammoth have settled unevenly, thereby causing the bottom and roof to break into blocks. In attempting to mine over a large area of the No. 5 or Buck Mountain seam, a similar settlement has been encountered; the roof of the seam has been broken and a considerable amount of timbering has been necessary in order to make the mining of the seam possible. The conventional breast-and-pillar method, using shaker conveyors, has been used in the No. 5 seam, and a slant-breast method in the mining of Nos. 9½ and 9¾ seams. Mining OF Light-pitch Seams The No. 4 seam was mined and robbed by the conventional breast-and-pillar system. In this area the seam pitched from 5° to 25° on the north dip, averaged 8 ft. in thickness and had a slate bottom and a

Jan 1, 1942

By Ian W. Wark, Keith L. Sutherland

IT has been shown' that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "standard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,2 it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator. It is not difficult to suggest an explanation for the influence of the carbonate ion in the presence of copper sulphate. The works of Picker-

Jan 1, 1939

By Howard E. McKinney

A high-pressure wellhead lubricator has been developed to facilitate telemetering electrical measurements from subsurface reservoirs to the surface with the well under normal flowing conditions. The field unit in use at the present time employs a 5/16-in diameter, single-conductor armored cable and is to be used in wells with surface pressures up to 5,000 psi. It has a pressure sealing element that maintains a continuous and absolute seal around the cable as it enters or leaves the tubing at speeds up to 175 ft per minute. A cable injecting device is used which obviates sinker bars or weight sections on the instrument. INTRODUCTION The development of instruments for securing physical measurements in pressure wells has been confined in the past to those instrument which would operate on a wire line and record the necessary measurements in the downhole instrument itself, or those which would operate on an electric cable in a well with the surface pressure killed by the use of weighted fluids or by the use of tubing plugs. In one case the accuracy of the measurements is questionable, and in the other the range of application is very limited. Considerable work has been done by other interests to provide effective means to accomplish the necessary telemetering. The U. S. Bureau of Mines developed a wellhead lubricator prior to 1947 which permitted a 5/16-in diameter single-conductor cable to be lowered into a well with a surface pressure of approximately 500 psi. This unit was used successfully in a number of tests in Oklahoma. A company which tests wells has recently offered on a service basis a wellhead lubricator with a 3/16-in diameter cable that reportedly operates up to 2,500 psi surface pressures. Each of the above operates on a staging principle to effect a seal. In both of these units some leakage of well fluid occurs when the cable is moved. SPECIFICATIONS FOR DESIGN In order to provide the maximum flexibility in its use, the following parameters were established for the design of our high-pressure wellhead lubricator: L An absolute well fluid seal up to 5,000 psi surface pressures. 2. Means for raising and lowering the instrument at speeds of at least 100 ft per minute. 3. Provision for the instrument to enter and leave the well without disturbing the well flow or the reservoir conditions. 4. A cable large enough to provide suitable electrical characteristics and suitable mechanical properties. 5. A method of operation that will not damage the well in any way. The present high-pressure wellhead lubricator field unit fulfills the above requirements. DESCRIPTION OF THE UNIT AND ITS OPERATION The cable selected for this use is the standard Amergraph 1H2 as manufactured by the American Steel and Wire Co. This particular cable is normally used by the Halliburton Oil Well Cementing Co. in their conventional well logging operations. Although the cable presents a noncircular cross-section (Fig. l), its diameter is very consistent; lor example, maximum diameter is 0.325 in., minimum diameter 0.314 in. This [actor permits the use of the sealing element, as later described. Early in the development of the high-pressure wellhead lubricator it was apparent that we could not effect a direct gas seal around a moving 1H2 cable. This becomes evident when an examination of the cable cross-section is made. The voids between the strands of the outer armor provide natural channels lor the flow and escape in large quantities of a low-viscosity fluid such as gas. However, it is relatively simple to

Jan 1, 1952

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946

By J. E. Gould, H. J. Hand

Many independent studies are being made on slag-metal relationships in the open-hearth furnace, and these studies cannot help but result in an ultimate improvement in the quality of open-hearth steel of both the open and killed types. In maintaining quality control at the National Tube Company's plant, emphasis has been placed on an evaluation of the iron oxide content of the steel in as quantitative a manner as possible, in order that the most desirable level of oxidation might be obtained for a given type of steel, and to secure a more precise basis for final de-oxidation. In the past, various methods were used for estimating FeO content of the metal at tap to ensure uniform and thorough deoxidation of killed steel, avoiding overdeoxidation to minimize the amount of inclusions present and to make as sound a steel as possible. For the open-type steels, such control involves obtaining the necessary level of oxidation for the most suitable action of the steel in the molds to provide good surface quality and cross section for the specific grade involved. While rapid analytical methods are available for determination of FeO in the liquid metal, such methods are still not sufficiently rapid for routine control on the open-hearth floor, nor do such analyses provide information as to what causes high or low FeO values. The method of sampling can still be considered a problem in view of the variability encountered in taking simultaneous duplicate tests. With the accurate rapid methods now available for determining carbon in the metal, estimating slag basicity and obtaining temperatures of liquid metal, it was believed possible to determine the influence of the various furnace reactions in establishiug the state of oxidation at a given time. Simultaneous slag and metal tests were used in this analysis, aided by statistical methods, to determine the factors that affect the metal FeO, and also to make a quantitative evaluation of these factors. Data obtained are from actual iurnace operations, the metal test being of the I spoon, Herty type, and taken in duplicate. Metal temperatures were taken with the open-tube bath pyrometer developed by the Research Laboratory of the United States I Steel Corporation. This method of taking open-hearth metal temperature was invented by Collins and Oseland,l and was developed into its present form by L. 0. Sordahl,2 of the Research Laboratory. The instrument and its mode of operation have been fully described by Sordahl and Sosman in three publications.3,4,5 lag components were obtained by chemical analysis. Data were taken from four 165-net-ton furnaces during the working period of the heat. Recognizing that additions of ore affect the metal FeO. no tests were included within 30 min. after ore additions. In all, 65 tests (48 heats) were used in this study.

Jan 1, 1942

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades' of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. CLAIRTON BY-PRODUCT COKE PLANT AND COAL WASHER The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of- approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1943

By E. A. Gulbransen, J. W. Hickman

The physical and chemical structure of the oxide films formed on metals and alloys is of interest in our understanding of their protective properties. According to Pilling and Bedworth,¹ if the specific volume of the oxide is equal to or greater than that of the metal, a compact or continuous structure results; if the volume of the oxide is less, a cellular or porous structure forms. With the cellular type of coating the surface layer of oxide offers no impedance to oxidation; at a given temperature the rate of oxidation is quite constant. On the other hand, the compact type of coating acts as an effective barrier to oxygen and the rate of oxidation will follow a parabolic law. The recent work of Gulbransen2 and of Leontis and Rhines3 on the oxidation of magnesium indicates that it is not necessary for the volume of the oxide to be greater than that of the metal in order that the oxidation may follow a parabolic rate law. One exception to the rule of Pilling and Bedworth¹ is noted by Scheil;4 namely, tungsten. At 500° and 700°C long-time oxidations indicate a linear rate law with time. However, Dunn's6 0xidation measurements from 700°to 1000°C indicate that a parabolic rate law is followed. The oxide is mainly yellow WO a with a thin layer of the blue oxide. Preliminary results on the oxidation of tungsten6 in the temperature range 400° to 500°C indicate that the oxidation does proceed according to a parabolic rate law. Irrespective of the actual rate law that tungsten may obey, it is of interest to compare the results obtained on the oxidation of tungsten in the thin film region with those found when the metal is scaling. A time-temperature study of the oxides formed on both molybdenum and tungsten may indicate whether there exist any peculiarities in the oxide structures of the thin film region compared with those of the scaling region of oxidation. In a recent paper the authors7 presented an investigation of the structures of the oxide films formed on the metals iron, cobalt, nickel, chromium and copper. The results of these studies are presented in graphical form as existence diagrams of the oxides on a time-temperature scale. The existence diagrams of the oxides occurring on some of the metals are simple and show few chemical transitions, but there are many cases in which the physical state of the oxide surface changes as a function of time and temperature, as evidenced by the appearance or disappearance of orientation effects and sharpness of patterns. In general an increase in temperature results in an increase in

Jan 1, 1947

By K. C. Gilbart, Edgar Stansfield

One of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal,

Jan 1, 1932

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By W. R. Crane

THE support of roof in mines is dependent largely on the character of the top rock and its occurrence. The formations overlying the orebed in the Birmingham district are sandstone and slate. The sandstone occurs in beds of sufficient thickness to constitute important elements in the system of support; the slate is relatively strong but is thinly stratified. The alternating beds of sandstone and slate furnish an excellent combination in that the former are strong and the latter are impervious; however, their continuity is broken by jointing or slip planes. The thickness, and consequent weight of the overlying formations, is important in so far as the size and arrangement of pillars are concerned but may be relatively unimportant, temporarily at least, as a factor in the support of the roof. The position of the respective beds of sandstone and slate, their relative thickness, and their inherent weakness because of the occurrence of faults and folds, may exert a predominating influence on their support in place, which is affected only in part by the weight of the cover. The only mine in this district that operates under a cover of approximately 2000 ft. (1900 ft.) is the Shannon so-called "twin slope," situated 14,000 ft. southeast of the portal of the No. 7 mine of the Tennessee Coal, Iron, & Railroad Co. The conditions in this mine indicate what may be expected in other mines when the same depth is attained; in fact the effect of pressure is shown in several mines that have not reached two-thirds of that depth. It is evident then that conditions affecting the support of roof will not improve but rather will become more difficult with the extension of the mines into the valley under a constantly increasing weight of cover. Further, the difficulties will probably be augmented by the occurrence of faults and other disturbed ground, the presence and position of which at present are largely unknown.

Jan 9, 1924

By Robert Bell

The regions to which this paper refers include the whole of the Dominion of Canada east of the 130 Rocky Mountains and north of the water-shed of the St. Lawrence. Very little exploration for economic minerals has yet been done in this immense country; but that little has already served to indicate great wealth in some localities. Having been engaged for a number of years in conducting government geological explorations in these vast territories, I shall endeavor to give the members of the Institute an idea of the prospective mineral resources of almost half a continent, as far as they are yet discernible. I purpose confining my observations to the economic minerals, and will not attempt a description of the geology of these territories; hut it will be necessary to say a few words about the rocks in order the better to explain the distribution of such minerals. The Laurentian nucleus of the continent is the principal feature of the geological map of the Dominion. It stretches from Lake Superior to Baffin's Bay, and from Great Bear Lake to the Straits of Belle Isle. Hudson's Bay itself, which is half the size of the Mediterranean Sea of the old world, lies in the center of this area. Its shores are bordered in places with newer rocks. On the west side of James' Bay (its southern prololigation) these extend inland over 200 miles, and consist of fossiliferous Devonian and Silurian strata. On the western and northwestern side of Hudson's Bay proper, altered rocks are met with, some of which resemble the gold-bearing strata of Nora Scotia, some the Huronian of Lake Huron, some the older Huronian, and others the crystalline series of the neighborhood of Sherbrooke in the Province of Quebec. Along the east coast (called the Eastmain)and among the islands lying off it, there is an interesting set of volcanic and sedimentary rocks which appears to be identical with the Animikie and the Nipigon series of Lake Superior. The area which I have characterized in a general way as Laurentian, includes tracts and belts, more or less extensive, of the Huronian series. Such areas appear to be most common, and have been best explored, in the country between the Great Lakes and Hudson's Bay.

Jan 1, 1886

[A Aall, Christian H., M49 D Mgr, American Metal Climax, Inc., 61 Broadway, New York 6, N.Y. Aaroe, S. L., A54 B Sales Mgr, The W. S. Tyler Co. of Can. Ltd., St. Catharines, Ont., Canada Abalos, Teodulo Q., J57 A Foreman, Lepanto Cons. Ming. Co., Mt. Province, Philippines Abbass, G., M55 P. O. Box 680, Hong Kong, China . Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abdullah, M. Y., J53 Dept. of Mines Res. Div., P. O. Box 1016, Tiger Lane, Ipoh Perak, Malaya Able, John F., Jr., J53 A Ming Engr, USA SIPRE 1215 Washington Ave., Wilmette, Ill. Abell, Leo M., M31 B Conct Supt, Phelps Dodge Corp., Morenci, Ariz. Abenius, Hakan Wilhelm, M52 A Mng Dir, Stora Kopparbergs Bergslags AB, Falun, Sweden Abenoroth, Harry F., A57 Natl. Carbon India Ltd., 18A Brabourne Rd., Box 217, Calcutta, India Abercrombie, Harry W., J56 1645 Camphor Dr., Lakeland, Fla.]

Jan 1, 1961

By C. J. Ramsburg

The construction and operation of by product coke-oven plants in America are essential to strong national defense and of the greatest importance to many widely diversified undertakings as well as to safety and health. Carbonization Process Coal used under a boiler or in a locomotive is consumed by combustion. Coal used in a by-product oven is distilled or carbonized, meaning that heat is applied to the coal, out of contact with air, causing a distillation that removes the volatile matter in the coal in the form of gas and vapor, leaving coke as a final product. From the gas and vapor distilled from the coal, many valuable substances can be secured, known as by-products. Hence the name "by-product oven." The simplest example of this principle can be shown by means of an ordinary clay pipe. If powdered coal is placed in the bowl of the pipe, the opening of the bowl is plugged with clay, and the bowl placed in a flame, the bowl will become hot, transferring the heat through the wall of the bowl to the coal within. When this coal attains a temperature of about 750°F., gas will begin to pour out of the pipe stem, and this gas may be lighted. A black liquid also will exude from the stem of the pipe, This is tar mixed with certain other products. What remains in the bowl after distillation is coke. A coke oven corresponds to the bowl of the pipe. A modern oven of the latest type is a refractory brick chamber approximately 42 ft. long and 14 ft. high, averaging 18 in. in width. The oven is filled with coal through closable charging holes in the oven top. Each end of the oven consists entirely of a self-sealing door, the removal of which permits the finished coke to be discharged by means of a power-operated pusher machine. The ovens are built in batteries, and the heating is effected by gas burned in vertical flues in the oven walls, each set of flues heating the walls of two adjacent ovens. Such ovens carbonize a charge of approximately 18 tons of coal in 18 hr., or have a daily throughput of 24 tons per oven, producing about 17 tons of coke. In times of need, the output may be increased by raising the temperature of flues, thus shortening the coking time. There is one great essential difference in principle between distillation in a clay pipe and in a coke oven. In the 18-in. oven, the distillation proceeds from two parallel walls held at a high temperature (over zooo°F.) and instead of all the coal being heated at once, the distillation is a progressive one creeping inward. The average travel of this heating is 35 in. per hour from each vertical wall, and as the volatile products are formed progressively they must push away from the interior toward the wall through the previously formed hot coke, then up the walls and Over the top of the coal charge, finally escaping through the outlet pipe. This results in a cracking of the components into many different and valuable substances not formed when the carbonizing temperature is low.

Jan 1, 1942

By Leons Kovisars

Introduction Competitive analysis is the collection and evaluation of data on a product, a product line or on an entire industry. Much of the focus of competitive analysis centers on production volume and the price targets of the competitors. In actual practice capacity may be used in place of production volume. Similarly, unit production costs and individual producing units - mines, mills, smelters, refineries - may be the targets of the analysis. The purpose of competitive analysis is to provide information for strategic planning. The analysis will locate the position of the company in the industry and define the competitive margin -- or lack of a margin - between the company and other producers. The analysis can show the current situation and may be expanded to examine the outlook for the future. The forecast option is particularly valuable because it will show the opportunities for new project development or the expansion of current production. Similarly, the forecast will show the potential threat from new entrants, and may provide early warning to reconsider operations that may become uncompetitive in the future. Production cost analysis is a clearly understood means to evaluate producers and estimate the outlook for their profitability. The cumulative cost for the industry outlines the supply structure and defines the marginal cost of production used in developing price forecast as explained in the sub- sequent section of this paper. Competitive analysis is particularly important to the mining industry, notably to metal producers. The final product is typically a purified metal conforming to standards, and interchangable with the output of other producers, i.e. a fungible commodity. Brand loyalty is questionable in the mineral industry. Consumers will show a preference for specific brands, but this preference will be limited to a premium of several percent over the general market price. Price and assurance of supply are the keys to marketing success. Assurance of supply depends on geopolitical considerations and production capabilities. Price will be closely related to cost of production and a thorough competitive analysis should describe the cost structure of the industry. This snapshot will locate one's own position and provide an immediate and readily understandable evaluation of the hazards and opportunities inherent in this position. In the following section we shall discuss elements, methods and sources for competitive evaluation. ELEMENTS OF COMPETITIVE ANALYSIS The practice of systematic collection and analysis of data on competition is hardly a new concept; see, for example, Wall (1) or Porter (2). However, most discussions have been in the context of conventional industrial or manufacturing industries, with a focus on product lines and brand marketing. These considerations are not irrelevant to mining but they do have only a limited application. The key to success in the mining industry is minimizing the cost of production. However, this simple concept becomes complex when we consider relevant costs and the planning horizon. Production costs include the factors consumed in production, namely labor, fuel, energy, materials and supplies. The cost also includes purchased and contracted services such as freight, smelting and refining, sampling and sales required to convert ore to the finished metal. Royalties and ad valorem taxes paid on gross production are direct expenses, as is the cost of administration required by the production units. The sum of these outflows is the total cash cost, the expense that has to be paid in cash in order to continue production. Indirect costs incurred by a producer will commonly include allocated headquarters expenses, as well as the capital charges associated with equity investment and debt. Profit is not generally considered an indirect cost even though it represents the cost of using the owner's capital; similarly, income taxes represent the government's participation in the profits of the enterprise. Interest payments are considered as a direct expense in some cost studies, but many competitive evaluations would consider

Jan 1, 1985

By G. St. J. Perrott

One of the important hazards in coal mining is the danger of ignition of explosive mixtures of methane and air or coal dust and air, or both, by the explosives used in blasting the coal. It has long been recognized that certain explosives are more dangerous than others in this respect. ' In America and abroad, government testing stations have been established for officially passing on the suitability of explosives for use in coal mines. In this country the Federal government is given no power to enforce the use of the approved explosives but merely publishes from time to time, through the Bureau of Mines, those explosives which have passed the tests necessary to place them on the list for use in coal mines. In spite of this lack of police power, the increase in the use of permissible .explosives since the promulgation of the fist list in 1909 has been rapid. In 1912, only 8 per cent. of the explosives used in coal mines were permissible; in 1925, this figure had increased to 25 per cent. While the past record of permissible explosives has been most gratifying, it is very desirable that we pave the way for further improvement in explosives and blasting methods by learning more about the mechanism of ignition of gas and coal dust by explosives. To this end a considerable amount of investigative work already has been carried out and a large amount yet remains to be done. It is the purpose of this paper to discuss briefly the effect of the characteristics of explosives and method of loading in the borehole on the liability of a blown-out shot to ignite explosive mixtures of gas or dust. For an account of the methods by which an explosive is tested for permissibility for use in coal mines, the reader is referred to Schedule 17-A of the U. S. Bureau of Mines. Safety Factor in Using Explosives The factors that affect the liability of an explosive to ignite gas or dust are already known in a qualitative way but quantitative data are

Jan 1, 1927

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958

By Galen G. Waddell

Several years of rock-burst research conducted by the U.S. Bureau of Mines in cooperation with the mining companies of the Coeur d'Alene mining district, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem. A rock burst is the sudden, violent release of stored strain energy in rock by some mechanism of rock failure, generally accompanied by expulsion of rock with consequent damage to the mine. A burst may be audible for only a few hundred feet, or on the surface it may sound like a sonic boom miles away. A Dictionary of Mining, Mineral, and Related Terms, U.S. Bureau of Mines (USBM)* 1968yand defines a burst as Bureau "That phenomenon which occurs when a volume of rock is strained beyond the elastic limit and the accompanying failure is of such a nature that accumulated energy

Jan 1, 1971