Search Documents

By J. M. Flaitz, A. S. Parks

OF the various methods of sampling gas-condensate wells, a method that secures a continuous representative sample of the well stream is desirable. Such a method, consisting of a sampling tube introduced into the well tubing, has proved satisfactory. The method is sufficiently accurate for operating and engineering problems A portable testing apparatus can be used with the sampling tube to obtain data useful in studying the economic and technical aspects of the development and operation of gas-condensate properties. Introduction The recent discovery and development of gas reserves that contain hydrocarbons that condense with reduction of temperature or Pressure, or both, to form a product known as condensate, has brought many new problems to the oil and gas industries. With further discovery of deep, high-pressure fields it is presumable that many more gas fields of this type will be added to the steadily increasing number. Such gas reserves are found either associated with oil as a gas cap or in separate formations. There seems to be no positive correlation between the physical or geological nature of the reservoir, and the chemical composition or phase characteristics of its contents. Knowledge of the chemical make-up and phase behavior of gas-condensate reserves is needed to cope with many problems. A knowledge of the chemical composition and phase characteristics of the reservoir material is necessary to properly design a gasoline or recycling plant, to estimate natural gas and condensate reserves, to enable the operator to study the economic and technical aspects of various methods of operation and development, and to carry Out the plan of operating subsurface and surface lease equipment. This information is often useful in questions of mineral ownership, proration, legal position, and taxation. It is the purpose of this paper to discuss methods used by the writers to determine the chemica1 composition and phase characteristics of the fluids produced from a condensate well. The scope of the paper includes a discussion and description of the method of sampling, the results of tests on the accuracy of the sampling method, a description of a portable testing apparatus used to examine the phase characteristics, typical results of tests on wells from several condensate fields, and some of the applications of these data to production problems. References to previous work on this subject are cited at the end of the paper. The Problem At reservoir conditions of temperature and pressure, the fluids produced from a condensate well exist in a homogeneous vaporous condition. The consequent reduction of temperature and pressure that occurs as this gas enters and flows up the well tube results in condensation of some of the hydrocarbon material to form a liquid. The relative amount of liquid condensed at any point in the flowing system

Jan 1, 1942

By Joseph C. McCaskill

The writer assumes that this volume is not intended to serve as a source of statistics on international trade and that the reader is not interested in wading through a lot of statistical tables copied from the various reporting agencies. Generalizations therefore are made whenever possible and not always is the source of the information meticulously cited. The United Nations regularly publishes trade data on mineral commodities. E. J. Gealy, and C. L Kimbell, of the U S Bureau of Mines (USBM), work with these data and estimate that they cover approximately 78% of total mineral commodities traded. In addition the General Agreement on Tariffs and Trade (GATT) publishes analyses of certain trade data The most complete report of production and trade in minerals 1s probably the international volume of the U.S. Bureau of Mines Yearbook The latest available edition is for 1968, and some of the data in this edition cover only as late as 1967. Unless otherwise stated, the source of data used in the chapter is this Yearbook Other staff members of the Bureau were most helpful and cooperative They are not to be held responsible for conclusions or points of view to be found in the chapter. THE NATURE AND SCOPE OF INTERNATIONAL TRADE The two and a half decades since World War II have witnessed an unprecedented growth international commerce The end of the war found the world economy seriously crippled. Many countries had suffered severe war damage; international trade was disrupted and nations had to resort to exchange controls and bilateral trading arrangements. The postwar recovery, however, was remarkably rapid Within two decades, world Income more than doubled, and world trade which was less than $60 billion in 1948 exceeded $200 billion in 1968, 8 and reached $278 billion in 1970.18 The growing world trade contributed to world prosperity which in turn fostered growth of trade. This dramatic growth of international commerce was made possible by the progressive liberalization of trade and capital movements by the major trading nations of the world which began immediately after the War and has not yet completely lost its steam. The modern-day stimulus of the expanded trade movement was the enactment by the Congress of the United States in 1934, of the

Jan 1, 1976

By R. J. Hafsten, E. S. Davenport, R. A. Grange

THE influence of austenite grain size upon the hardenability of steel is now fairly well understood; for a given austenite, increasing the grain size increases the depth of hardening, and, since the latter is related to the fundamental transformation behavior of austenite, it follows that austenite decomposition must, in general, be retarded by increasing grain size. To date, very little quantitative information bearing directly on the effect of austenite grain size upon the progress and result of isothermal transformation has been published. Davenport and Bain,1 and Zimmerman, Aborn and Bain2 have shown that the transformation is definitely retarded in hypereutectoid plain carbon steels at temperatures near and above the upper region of rapid transformation (Ar') when the austenite grains are increased in size. More recently, Griffiths, Pfeil and Allen3 investigated the effect of a series of different heating (austenitizing) temperatures upon the progress of isothermal transformation at 1245°F. (675°C.) and 745°F. (395°C.) in a medium carbon, low-alloy steel; while they reported no measurements of the austenite grain size, their results suggest that increase in grain size retards austenite transformation at 1245°F. (675°C.), but has no appreciable effect at 745°F (395°C.). The present paper deals with the results of a study of the isothermal transformation of austenite in a single commercial alloy steel in which a fine-grained or a coarse-grained state was induced by appropriate selection of austenitizing temperature. The data are presented in the form of isothermal transformation diagrams, which clearly show that coarsening the grains lessens the rate of transformation of austenite to proeutectoid ferrite and pearlite-that is, at temperature levels above about 1000°F. (540°C.)-but is without significant effect at lower temperatures where the transformation product is bainite or martensite. It is to be presumed that the foregoing statement would be valid, at least in principle, for many other grades of steel; it confirms again that the mechanism of transformation to a pearlitic structure is fundamentally different from that to an acicular structure. A number of related observations were made, which seem to throw some light on the transformation process as it takes place in alloy steels, particularly at temperature levels in the vicinity of 1000°F. (540°C.), where the transition from lamellar to acicular structures occurs. These data are discussed briefly in the belief that they may lead to a clearer understanding of this aspect of the subject. MATERIAL AND EXPERIMENTAL PROCEDURE The material investigated was a commercial grade of S.A.E. 4140 steel, the composition of which was as follows: 0.37 per cent C, 0.77 per cent Mn, 0.98 per cent Cr and 0.21 per cent M0. It was hot-rolled to a 1 1/8-in. round bar and normalized by air-cooling from 1800°F. (980°C.).

Jan 1, 1941

By Clarence A. Seyler

The technical difficulties of cutting thin sections of coal for examination by transmitted light have hitherto restricted the investigation of the important subject of the microstructure of coal to the few possessed of the requisite skill and time. Apart from this, the method fails with anthracites and other coals rich in carbon, owing to the opacity of the material. Occasional use of the method of polishing a surface, with or without etching, has been made, but it was not until Winter' published an account of his results that attention was seriously directed to the method. In May, 1923, a specimen of dull anthracite came into my hands; I tried Winter's method on it and the presence of megaspores and other vegetable structures became clearly visible. A preliminary notice was published by me;2 but I soon abandoned the use of Schulze's solution, having found that a mixture of chromic and sulfuric acids gave far better results. In the meantime Turner and Randall, in America, had independently developed the method of flame etching, as applied to anthracite, with great success. I have spent a year studying the method of chromic etching, which gives excellent results with bituminous coals and camels, as well as with anthracite. For anthracites, I have used the chromic method and Turner's method of flame etching, whichever was the more convenient or as a check one on the other. The polishing is done, according to metallurgical practice, by the use of a polishing machine and successively finer emery paper, followed by polishing on cloth moistened with a suspension of levigated green oxide of chromium, and a final rubbing on "selvyt" (a cotton velvet polishing cloth) moistened with alcohol. The polished sample is examined by reflected light with a 2/3 and 1/6 in. objective. Bituminous coals usually show considerable structure, and even anthracites show it faintly in places. The sample is then etched by immersion in a boiling solution made by adding 10 c.c. of concentrated sulfuric acid to 30 C.C. of a saturated solution of chromic acid; enough water is then added to dissolve

Jan 1, 1925

By C. M. Wayman, R. Bullough

The selection rules fir twinning in fcc, bcc, and hcp lattices as established in Part I are used to predict the positions, relative to the matrix (untwinned) reciprocal lattice, of reflections due to double diffraction from the twins. These doubly diffracted reciprocal lattice points, which often coincide with ordinary matrix reciprocal lattice points, are deduced from kinematical considerations. 1. INTRODUCTION. A Bragg diffracted beam under certain conditions may be rediffracted to produce a third beam i .e., the incident beam, the first diffracted beam, and the rediffracted beam). In such a case an initial incident beam is diffracted by a set of planes; the diffracted beam may then be rediffracted by a second set of crystallographically different planes. The initially diffracted beam acts as an incident beam for the second set of planes, thus resulting in a twice-diffracted beam. This twice-diffracted beam may be regarded as a singly diffracted beam from a set of lattice planes whose structure factor is zero. In order to find the reciprocal lattice point corresponding to the doubly diffracted beam, it is customary1,2 to combine vectorially the component reciprocal lattice vectors which head to the extra reflections. For example, hcp metals may exhibit the forbidden (0001) reflections.* As Fig. 1 shows, the (0001) reciprocal lattice point results from: (1010) + (1011) = (0001) Similarly, combination of the beams (1011) and (1010) gives rise to: (1011)- (1010) = (0001) As Pashley and stowell2 have pointed out, even if in fact the double diffraction points lie on the Ewald sphere, they may not actually represent observed doubly diffracted beams because the initially diffracted primary beam, i.e., the source, must also correspond to a reciprocal lattice point which lies on the sphere of reflection; however, the reciprocal lattice point corresponding to the planes causing the rediffraction need not lie on the sphere. A little consideration of the Ewald construction in Fig. 2 makes this argument clear. In Fig. 2 the incident beam is represented by the wave vector ko. This beam is initially diffracted by the lattice planes (hkl) which are represented by the reciprocal lattice vector r(hk1) The reciprocal lattice point (hkl) of course lies on the Ewald sphere in order that the Bragg condition be satisfied. The initially diffracted beam is represented by the wave vector kl. If now kl is rediffracted by a second set of planes (h'k'l') resulting in k2 the lattice point (h"k"l") must lie on the Ewald sphere if the double diffracted beam k2 is to be observed. It is clear that (h"k"l") is the vector sum of (hkl) and (h'k'l'), and that (h'k'l') need not in fact lie on the Ewald sphere. In the usual1,2 analysis the origin (000) of the reciprocal lattice is shifted to the point (hkl). However the translation (000)— (hkl) automatically shifts the point (h'k'l') to the Ewald sphere, i.e., (h'k'l')— (h"k"1"). It is to be seen that (hkl), the source reflection, must lie on the Ewald sphere; if it does not the translation (000) — (hkl) places the "new" origin off the sphere, not satisfying the Ewald construction and hence the Bragg condition. The point (h"k"1") of course must lie on the sphere if it corresponds to an observed doubly diffracted beam. It is to be noted that crystals having the hcp structure, as just discussed, are intrinsically capable (i.e., without lattice defects such as twins) of double diffraction, as contrasted to fcc and bcc crystals which are extrinsically capable (requiring lattice defects or reoriented lattice regions). The "allowed" bcc reciprocal lattice points (which comprise an fcc lattice) are (110), (2001, (211), (220), (310), (2221, (321), (4001, and so forth. The combination

Jan 1, 1967

By F. A. Crossley

The titanium-rich end of the Ti-A1 system has been investigated up to 35 at. pct A1 (23 wt pet). One conzpound Ti3Al was found to occur between primary a and TiAl. It is ordered hcp with DO19 structure, it has virtually no solid-solubility range, and it has a closed maximum at about 875°C. OIL either side of the compound are a +Ti3Al two-phase fields. The limiting a1uminum solubility in primary a at the titanium-rich end is indicated to be 7.5 at. pct A1 (4.4 wt pet) at 550°C and about 6.8 at. pct Al fl wt pct) at 500°C. Quenching alloys from above the a + Ti3Al two-phase field produces the following structures with respect to alloy composition: Up to 13 at. pct A1 (7.8 wt pet), a solid solution; from 15 to 18 at. pct A1 (9 to 11 wt pct), shear transformation product or martensite; from 19 to approximately 30 at. pct (11 to 19 wt pet), submicro-scopic coherent Ti3Al in an a malvix. The twin hcp phase fields reported in the literature are the result of nonequilibrium corzdztions. Ti-A1 alloys, once partitioned by dwelling- in the a + ß phase field during either hot working or heat treatment, are extremely difjicult to homogenize at temperatures below 1000°C. Such partitioned alloys exhibit the characteristics or symptoms of two-phase materials, and may be said to suffer the "twin-phase syndrome". THE earliest investigations of the Ti-A1 system by Ogden et al.1 and Bumps et al.2 reported wide solubility of the primary solid solutions. Aluminum was reported soluble in the low-temperature allomorph to the extent of 37 at. pct (25 wt pct), and the first intermediate phase was reportedly TiA1. Somewhat later Kornilov et al.3 reported a similar diagram with phase boundaries displaced towards lower aluminum contents and higher temperatures. Beginning about this time (1956) reports in the literature made it very clear that one or more intermediate phases occurred at lower aluminum contents than TiAl.4-17 These reports included five major investigations of the titanium-rich end of the Ti-A1 diagram.4,12,14,16,17 Three of these diagrams show two two-phase fields below 37 at. pct Al, while two of them show a single two-phase field. The existence of the phase Ti3A1 is firmly established and is included in each of the diagrams, except one—that of Sato and Huang.12 The new phases are reportedly hcp and differ from primary a only slightly when disordered, and when ordered the "a" parameter is approximately one,4,12,15 two, 6-10,13,14 or four14 times that for primary a. Beyond this, however, the diagrams are remarkable for their lack of agreement. Two tacit assumptions are usually made in phase-diagram determinations of metal systems. These are: 1) equilibrium anneals bring the alloy to equilibrium or to indistinguishable closeness to it, and 2) equilibrium conditions established at elevated temperatures are either "frozen" by rapid quenching for evaluation at room temperature, or quench-transformation products are recognized as such. In the current investigation evidence was obtained that over substantial composition ranges neither of these two conditions was met in any of the more recent major investigations. I) MATERIALS, METHODS, AND TECHNIQUES The alloys of this investigation were prepared by nonc on sum able electrode arc melting. Materials used in the preparation of the alloys are summarized in Table I. The investigative tools employed were: optical and electron microscopy, differential thermal analysis (DTA), disatometry, X-ray diffraction, electron diffraction, and resistometry. Alloys for microscopic and X-ray investigations were prepared as 15-g melts. Alloys containing from 7 through 11 at. pct A1 were hot-rolled out of a furnace at 900°C, from 12 through 15 at. pct out of a furnace at 1000°C, and from 16 through 18 at. pct out of a furnace at 1125°C. Alloys containing more than 18 at. pct A1 could not be hot-rolled. The ingots were covered with Markal coating prior to hot rolling to minimize atmospheric contamination. After hot rolling, alloys containing up to 15 at. pct A1 were ground and pickled to remove 7 mils from each surface; alloys containing 16 and 18 at. pct A1 were skinned to a

Jan 1, 1967

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metal-lurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each, temperature from room temperature to fusion tempera-ture, and cooled at a rate that is not generally controllable but is pre-determined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each tem-perature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and dis-advantages of the extent of the zone are of prime moment, and are dis-cussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known.

Jan 1, 1935

By J. F. Keefe, C. J. Bier, O&apos

This study was carried out with copper because it represents the simplest form of sintering, in that but one metal is involved and all reactions occur in the solid state. The present work will cover three variables affecting the sintering process; namely, briquetting pressure, sintering temperature and time in hot zone. Although strength and dimensional changes were observed, this is primarily a metal-lographic study of the sintering process in copper. The term "sintering" should be understood to mean the process by which the metal powder particles of the compact become united into one body. Material Used The copper powder used was made from reduced copper oxide, and is typical of a grade used for the mass production of parts formed of metal powders. The screen analysis of the powder was as follows: Per Cent Per Cent BY BY Particle Size "Weight Particle Size "Weight Mesh Microns /80.... 0.00 43/32.... 17.49 80/I00..... 32/20......16.68 100/140.... 0.34 20/10.... 23.14 140/200___ 15.25 10/5..... 4.64 200/230....... 5.00 5/0...... 0.75 230/325.... 16.70 — 325....62. 69 The minus 325-mesh analysis was made by using a Roller Air Analyzer.1,2 The apparent density is here defined as the weight per cubic centimeter of the loose, unpacked powder as measured with the Hall flowmeter. The value for the powder used was 2.57 grams per cubic centimeter.

Jan 1, 1945

By Courtenay de Kalb

The following observations upon onyx-marbles are fragmentary, and may shortly be rendered superfluous by the appearance of a work upon these interesting stones by Prof. George

Jan 1, 1896

By D. M. Lewis, R. C. Emmett, B. C. Wojcik, F. A. Baczek

The ElectroSlurry™ electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon cathode, while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes. The dust is processed through several stages consisting of leaching, copper precipitation, ElectroSlurry electrowinning, and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1981

By Andrew Allan

The Thompson Creek Coal & Coke Corp. operates three coal mines which presently supply the United States Steel Corp. with high grade, medium volatile coking coal at a rate of 1000 tpd. Mining is done at an elevation of 8000 ft, approximately 13 miles southwest of the small town of Carbondale, Colo. The coal is cleaned mechanically by heavy media and Deister tables, after which it is trans- ported to the railhead at Carbondale. GENERAL GEOLOGY The coal beds in this area lie in the Mesa Verde formation of Cretaceous age. Three beds are now being mined, with a fourth possibility pending further exploratory work. Formation of the Rocky Mountains tilted the sedimentary strata approximately 30º and created considerable faulting throughout. These faults, which range from a few inches to 35- ft displacement, constitute serious obstacles to mining.

Jan 4, 1966

By C. W. Volek, G. Mandl

Steam-injection tests in the field have shoum that heat transport into the oil/water region, ahead of the steam zone, may have a significant effect on the production process. Earlier theoretical work on reservoir heating by hot-fluid injection can be used to describe the growth of the steam zone, but only if heat transport from steam zone into oil/water region is neglected. It therefore became necessary to re-examine and extend the earlier theory. It was found that this theory ceases to be consistent with the physical model of the process at a certain critical time, tc, which depends on reservoir thickness, temperature, and quality of the steam. The critical time marks an important change in the heat flow across the condensation frovt: the heat flow, which is purely conductive during 0 < t < tc&apos; becomes predominantly convective at t = tc. Accordingly, at t = tc, the equation which governs expansion of the steam zone changes. On the basis of the new equation, an approximate description for the steam-zone growth during t > tc is developed by making use of upper and lower bounds for the exact solution of the problem. The boundary conditions for heat and mass flow inside the oil/water region are established, and a simple method of detennining the saturation at the downstream side of the condensation front is presented. Experimental results show that the theory gives an accurate description of steam-zone expansion before the critical time. At times near critical time, and also after critical time, experimental data show theoretical steam-zone volumes to be high. Even so, the accuracy of the calculated steam-zone volumes is sufficient for practical purposes. THEORY OF STEAM-ZONE GROWTH INTRODUCTION The engineering evaluation of steam-drive processes is based mainly on a mathematical description of reservoir heating by hot fluid injection presented several years ago by Marx and Langenheim.l This theory can be used to determine the growth of the steam zone,2 provided the flow of heat from the steam zone into the liquid zone ahead of the condensation front (Fig. 1) is neglected. Since we must expect, however, that heat transport into and inside the liquid region (the region between condensation front and production wells) will affect both the water/oil flow and the growth of the steam zone, it is necessary to re-examine and to generalize the Marx and Langenheim theory as applied to steam drive, which will hereafter be termed the "old" theory. Observations made in several field tests emphasize the need to study the heat flow across the condensation front (CF). On several occasions it was discovered that heat was transported in the liquid zone far ahead of the advancing CF, resulting in an early breakthrough of warm water. This seems to occur most often when high injection pressures are applied, when "wet" kONINKLIJKE/SHELL EXPLORATIE EN PRODUKTIE LABORATORIUM RIJSWIJK, THE NETHERLANDS SHELL DEVELOPMENT CO. HOUSTON, TEX.

Jan 1, 1970

By Samuel L. Hoyt

Cemented tungsten carbide, a product of a branch of metallurgy which has never possessed more than a relatively minor interest and importance, has recently commanded the attention of engineers, industrialists, financiers and men of business. New methods, new opportunities, new goals, never before considered, have suddenly been brought within the scope of practical realization. It is these results that attract the interest of the world, but we, as engineers and metallurgists, will have equal interest in the product itself and in that branch of metallurgy from which it comes. It seems appropriate, therefore, to speak today on Hard Metal Carbides and Cemented Tungsten Carbide, as the latter represents one of the outstanding developments of recent date in non-ferrous metallurgy. We are interested in the hard metal carbides as a group of related metallic substances and in cemented tungsten carbide as the leading representative of the metallurgy of this group. The literature of this general field is limited, and, bearing this in mind, it seems advisable to attempt to cover the field broadly and to correlate the subject matter, rather than to present a detailed account of any one of its phases. Our annual lecture lends itself admirably to this plan. The quickened interest in cemented tungsten carbide, once its potentialities were recognized, the many sides to the problem of developing the manufacture and use of this new product, and the desire to economize as much as possible in the time of development, have brought many into this work, both in this country and abroad, notably the Osram Lamp Co. and Friedrich Krupp in Germany and the General Electric Co. in this country. It would be presuming too much to attempt to speak too broadly of the present state of the art and science of the hard metal carbides and my remarks arc guided largely by the work done in the General Electric Co., and by our associates in the Carboloy Co. Even here the activities of many in these two groups have centered around the utilization of cemented tungsten carbide, which is outside the scope of this talk. To those whose work is represented in this lecture, it is my pleasant duty to acknowledge their assistance and advice. To Dr. Zay

Jan 1, 1930

By J. George Gregr

INTRODUCTION This part contains field case studies of typical mishaps, accidents, equipment damage or post installation failures resulting from mistakes in design, manufacturing and construction, as well as improper storage, handling and installation procedures of the equipment covered in Part 1. GENERAL Certain mistakes are repeated and common rules violated on almost all industrial equipment installations, with the inevitable consequences of additional cost, construction delays and aggravation of all parties involved. The most common failures are in the following areas: Cleanliness of all components during installation and later in operation. Adherance to manufacturer&apos; s recommendations and tolerances for equipment installation. Comprehensive, properly identified installation and maintenance records. Handling of the components. Adequate tooling and auxiliary equipment in working order. An inoperable hydraulic power unit for torque wrench or for jacking of the mill, or faulty crane can be a very costly proposition. A special area in comminution circuits are wear components. Apart from the mill liners, the wear components such as, feed chutes, rock boxes, mill trunnion liners, discharge sumps, etc. are designed to the best theoretical configuration, based on experiences in similar installations. However, each process is different to a various degree, mainly because of various types of ores and grinding requirements. Consequently the first generation of wear components is very seldom the ideal one. Based on operational experience, the shape and material of wear components should be modified, until the optimum, most economical design is achieved. SHIPPING AND STORAGE Considerable damage to the equipment can be done by careless packing, shipping or storage.

Jan 1, 1982

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals&apos; has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By C. S. Matthews, P. Hazebroek, H. Rainbow

It ha been suggested that lormation fractures created by well stimulation treatments will adversely affect sweep-out efficrency in injection operations. Fluid-flow model studies involving vertical fractures of various lengths and fluid systems of various mobility ratios have been carried out to study this subject. In addition, limited data have been obtained on one model containing a horizontal fracture. It was found that relatively long and highly conductive fractures (not generally obtained fracturing operations) were required to affect the sweep-out efficiency substantially. In a given case in the field an approximate distinction can be made between the presence of long conductive fractures and shorter or less conductive ones. This is done with pressure build-up analyses along with data on the relationship of fracture length and conductivity to well productivity. This type analysis shows that usually the fractures induced are either short or of limited conductivity and therefore do not damage sweep-out efficiency. INTRODUCTION Improved well productivity and in-jectivity can frequently be exploited in injection operations. Higher total throughput can yield improved economics. On occasion, the achievement of an increased productivity or injectivity in specific wells can bring about a more uniform sweep of the reservoir. Higher rates can be exploited particularly in water floods of "depleted" reservoirs where a rapid "fill-up" is desired and where low pressures contribute to low well productivity. The creation of fractures local to the wellbore is an excellent means for achieving these objectives. Even though fracturing has been employed in some floods with success,1"3 there still seems to be some reluctance to employ this tool for fear of undue damage to the flood pattern and ultimate recovery. We therefore need to examine the influence which fractures of varying length may have on flood performance and then determine the length of fractures which obtain in the field with conventional fracture treatments. A substantial influence of fractures on the recovery obtained at breakthrough of the injected fluid has been presented by Crawford and Collins for equal fluid mobilities for the line-drive pattern.4,5 In addition, the influence which a fracture has on the production performance after breakthrough and on the ultimate recovery warrants consideration in reaching a conclusion concerning the use of induced fractures in flooding operations. This report presents this type of data for the five-spot injection pattern for several fluid mobilities. In arriving at some conclusion concerning the fracture lengths obtained in field operations we must examine the performance characteristic most affected by the fracture. This is the change in the flow system as reflected in the change in productivity and pressure build-up behavior. A study of these changes is also presented in this report. RESERVOIR ANALOGS The X-ray shadowgraph technique, employing miscible displacement in porous models, has been used in the study of the influence of fractures on pattern sweep-out efficiency. The X-ray shadowgraph procedure is described in detail in an earlier report8. Fractures were represented by leaving the proper portion of the model surface exposed to either injection or production. This assumes the fracture resistance to be negligible compared to that of the formation. Actually the flow resistance in propped fractures obtained in the field is sometimes not negligible so that the results with this model indicate the maximum influence of the fracture. Two types of models were necessary to represent vertical fractures in a five-spot flood. These pattern elements are illustrated in Fig. 1. In studying the influence of the horizontal fracture, only one well spacing length to thickness ratio of 50 was used. The pool unit of a Carter Electric Analyzer was used in studying the influence of fractures on productivity and build-up behavior. The square drainage system of a well was represented by a network of 576 elements of equal volume and resistance. One-fourth of this drainage area was studied as a model unit using a network of 144 condensers and resistors. Vertical fractures were represented by a shunt directed from the well perpendicular to the drainage boundary. Horizontal fractures were represented by a circular shunt. Resistance of a shunt was varied in representing different conductivities for the fractures. FRACTURE DIRECTION AND LENGTH The direction at which a vertical fracture extends into the formation and its length and conductivity influence the sweep behavior. The two

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals&apos; has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By K. A. Natarajan, I. Iwasaki

Platinum electrodes are not inert as often thought to be. The reactivity of platinum electrodes can explain their erratic behavior in many electrochemical measurements of metallurgical interest, e.g, in flotation systems, streaming potential measurements, contact-angle measurements, and in leaching systems. The anomalous behavior of platinum electrodes in redox potential measurements in aqueous systems was studied through Eh and pH measure ments in water-oxygen, iron-water-oxygen, and manganese-water-oxygen systems. Stability relations between Fe++ and Fe (OH), and between Fe (OH), and Fe (OH), were studied to judge the correspondence between experimental and theoretical equilibrium lines. The practicality of redox potential measurements in estimating ferric-ferrous ratios in aqueous systems was investigated along with their suitability as indicators in leaching operations, e.g., the removal of iron by aeration from manganese leach solutions. Platinum electrodes have often been used in the measurement of dissolved oxygen concentrations and of redox potentials (Eh) in a variety of fields, e.g., analytical chemistry,&apos; corrosion," geology and mineralogy,,&apos;&apos; biology,"&apos; sewage treatment,&apos; * hydrometallurgy,"I" and flotation."la The effectiveness of Eh-pH diagrams, first reported by Pourbaix&apos; in 1949, has contributed much towards the theoretical understanding of numerous problems encountered in the metallurgical industry. Not many references are available in the literature, however, wherein attempts have been made to confirm Eh-pH diagrams from experimental measurements. One reason might be that, in spite of the apparent simplicity of the electrochemical technique, the direct measurement of Eh involves complex practical problems.&apos; Factors such as the purity of the solution, the type of electrodes used, the history of the indicator electrode, and the type of atmosphere (namely, oxidizing, reducing, or inert) do have effects on the measured Eh values. The influence of mixed potentials cannot be underestimated. The poisoning of platinum electrodes by organic and inorganic impurities present in the solution may lead to erratic results. Platinum, commonly thought to be an inert electrode material, is not really so, as attested by a number of previous investigators who advised caution concerning the anomalous behavior of platinum electrodes in various electrochemical measurements.&apos;" In the present article, a few pertinent experiments related to Eh-pH measurements in systems of interest in the metallurgical and water pollution fields are described in an attempt to correlate such information with what is already known, especially in the electrochemical literature. Iron-water and manganese-water systems were selected with a view of studying the correspondence between experimentally observed and theoretically established equilibrium lines. The work included an investigation of the behavior of platinum electrodes with respect to pretreatment and adsorption characteristics, the measurement of dissolved oxygen concentrations and their relation to Eh, the determination of the electrode potential of the ferric-ferrous couple at different pH, and the measurement of oxidation potentials in iron-manganese leaching systems. Experimental Procedure A rotating platinum electrode was used in many of the measurements to study the effect of rotation on measured Eh values. The electrode made by the Pine Instrument Co. consisted of a stainless steel rod with a platinum disk soldered to the end. It was covered with a Teflon insulation along the sides, so that only the circular tip of the electrode was exposed to the solution. Prior to its use, the platinum surface was brightened on a metallurgical polishing wheel with alumina as an abrasive, unless specified otherwise. The electrode was rotated with a Sargent cone-drive motor at 350 rpm. The contact of the electrode with the external circuit was made by filling a notch at the top of the stainless steel shaft with mercury and by dipping a copper wire into the mercury pool. The performance of the rotating platinum electrode was compared with the performances of a Beckman platinum button electrode and a platinum wire electrode. All the potentials were measured with respect to a saturated calomel electrode. A saturated KC1-agar bridge was used to minimize the liquid junction potential. A Beckman Zeromatic pH meter together with a Beck-man electrode switch was used to measure both the Eh and pH. A double-walled, all-Pyrex jar with a capacity of about 1 liter and themostated by circulating water of constant temperature was used for a reaction cell. Four equally spaced ports in the cover provided access for a glass electrode, a salt bridge connecting the saturated calomel electrode, a dispersion tube for bubbling gases into the cell solution, inlet and outlet tubes for passing the desired gases over the solution, and a graduated burette for introducing reagents from outside. The rotating platinum electrode was inserted through an opening in the top-center of the cover, and a positive gas pressure was maintained inside the cell to prevent air from entering into the cell compartment. A magnetic stirrer was used to mix the solution inside. For the determination of dissolved oxygen in the test solutions, the polarographic techniquex was used.

Jan 1, 1971

By B. Yu, H. M. Lee, R. P. Gardner

Some preliminary results are given on the use of radioactive tracers for implementing the mechanistic approach to flotation. The process studied is an industrial one for the cleaning of sand for the production of glass. The radioactive tracers employed are those produced from intrinsic elements in the sand by neutron irradiation in a nuclear reactor. The results indicate that the technique will be useful for the determination of flotation simulation mechanistic model parameters on operating industrial processes without interruption of their normal operation.

Jan 1, 1980