Search Documents

By T. B. Counselman

AN iron blast furnace of 1000 tons daily capacity will produce about 100,000 cu; ft. per minute of blast-furnace gas. This contains about 25 per cent of carbon monoxide, and has a B.t.u. value of about 95. This gas-is used primarily for heating the stoves of the blast furnace, and secondarily, under boilers, for steam production. Occasionally it is also used in gas engines. The raw gas coming out of the furnace carries about 10 grains of flue dust per cubic foot of gas, under best operating conditions. With the furnace "rolling" or slipping, this quantity may temporarily be greatly increased. This dust would, of course, deposit on the checkers of the stoves, or plug the burners under the boilers; therefore the gas must be cleaned.

Jan 1, 1936

By Lawrence Addicks

One of the properties of copper, which has done much to give it its present prominent place among the useful metals, is its electrical conductivity,—a property which has now become the chief criterion of the value of the commerical product. In pursuance of that distinctively American principle that, " the best is none too good," metal of the highest conductivity is usually called for even when such extreme purity is of no advantage ; for instance, in the making of brass and other alloys. The average brass-founder feels nervous unless his copper is so very pure that it shows a conductivity of 99 or 100 per cent., while the character of the zinc used is usually overlooked in hi s anxiety. Electrolytic refining has made it possible to produce copper

Jan 1, 1906

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the US, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available.1 The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts. Definitions of some terms used in this presentation are necessary before proceeding.

Jan 1, 1980

By William Kent

In the paper by Mr. Fernom, on Red Charcoal, read at the first session of this meeting, it was suggested that this fuel might be used in the blast furnace with greater economy than ordinary or black charcoal. In the discussion which followed the paper, it was stated that the charcoal furnaces of the Lake Superior District have used imperfectly burned charcoal with success, and that these furnaces have given the best results in fuel economy on record. On consulting some of our well-known metallurgical authorities the writer finds that the question of the use of red charcoal, or other imperfectly burned charcoal, or charred wood, is not at all new. In Percy's late work on Fuel, pages 409-414, are given a few facts, which are here condensed, as follows:

Jan 1, 1879

By Nicholas M. Short

Many a geologist or driller has wished he could somehow climb into a borehole to see for himself what fractures looked like. Or why recovery was poor. Or how the bit was actually lost. Now it is possible to do the next best thing to climbing into the hole. TV cameras are being used for a close-up look at borehole conditions. Ever since television was invented, geologists and others interested in subsurface conditions have wanted a TV camera that could be used in the narrow confines of a borehole. But development of such a camera was slow, mainly because of the need for compact size. Not until the late 1950's did the technology of electronic miniaturization develop to a point where a camera satisfactory for the purpose could be put together.

Jan 1, 1963

By W. C. Maurer

A drilling-rate formula for roller-cone bits is derived from rock crater-ing mechanisms. This formula holds for "perfect cleaning", which is defined as the condition where all of the rock debris is removed between tooth impacts. Under these conditions, the drilling rate is directly proportional to the rotary speed and to the bit weight squared, and inversely proportional to the bit diameter squared and to the rock strength squared. Under imperfect cleaning conditions, such m those usually present in field drilling, re-grinding of the cuttings occurs under the bit, and the drilling rates fall below those for perfect cleaning. INTRODUCTION Drilling with a roller-cone bit consists of two fundamental operations: the formation of craters under the bit teeth, and the removal of the broken rock from the craters. To delineate the mechanisms of drilling, it is first necessary to understand the mechanisms involved in the formation of individual craters and then to relate these mechanisms to the over-all drilling operation. CRATER FORMATION When a bit tooth impacts a rock, the rock is elastically deformed until the crushing strength of the rock is exceeded, at which time a wedge of crushed rock is formed below the tooth1, 2 as shown in Fig. 1. As additional force is applied to the tooth, the crushed material is compressed and exerts high lateral forces on the solid material surrounding the crushed wedge.- en these forces become sufficiently high, fractures are initiated below the tooth and propagate to the free surface of the rock. The trajectories of these fractures intersect the principal stresses at a constant angle,'s4, as predicted by both Mohr's and Griffith's theories of failure. It has been experimentally 3,1 .6 that the volume of an impact crater, V,, varies as where Ec is the total energy imparted to the rock during the formation of the crater, and E is the threshold energy required before cratering is initiated (Fig. 2). Indexing experiments' have shown that, when there is a second free face to which the crater can fracture, a larger volume of material is removed and that above a transition zone there is a linear relationship between V, and Eo., which has a slope equal to the relationship for the single crater. The beneficial effect of indexing tends to offset the threshold energy requirement to a large extent, as shown in Fig. 2, and the relationship is closely represented by Rate-of-loading effects have been used to explain the nonproportional relationships usually obtained between drilling rate and rotary speed. The data4, in Fig. 3 show that the Ec/Vc parameter remained constant for craters produced with impact velocities ranging from 10 to 8,000 ft/sec. Since no rate-of-loading effects were detected over this wide range of loading rates, it seems improbable that there would be detectable rate-of-loading effects present in the small changes in impact velocities produced by varying the rotary speed. The writer has shown (Fig. 4) that, for craters produced in rock by impacting spheres, where X is the depth of penetration. Simon2 has shown that this relationship also holds for craters produced in rock by penetrating wedge-shaped chisels. The energy used in crater formation is

By Henry M. Howe

THE death of Sir Lowthian Bell removes almost the last of the group of heroic leaders who made their age and ours the Age of Steel-a group which his luster and the luster of his peers, Bessemer, Siemens and Tunner, made one of the most brilliant, perhaps even the most brilliant, in the annals of industry. Born on February 15th, 1816, in Newcastle-on-Tyne, he was the eldest son of Thomas Bell, an alderman of Newcastle, and of his wife Catherine Lowthian of Newbiggin, near Carlisle, in Cumberland, and was christened Isaac Lowthian, the name of his maternal grandfather. His father was born about 1788, and came in 1808 from Newbiggin to Newcastle, where he entered the office of the Cumbrian firm of Losh and Company, manufacturers of alkali and wrought-iron, at the Walker Iron and Alkali Works, at Walker, Dear Newcastle. Young Isaac Lowthian Bell was educated at Dr. Bruce's school in Newcastle, whence he went to Germany and Denmark, learning there German and Danish. On his return he studied at Edinburgh University, and then at the Sorboune in Paris. As a student he already showed the remarkable character and application which later gained him such distinction. After studying the manufacture of alkali near Marseilles, he returned, and when about twenty years old (A.D. 1836) was employed in his father's firm, then called Losh, Wilson, and Bell. After spending a year in their Newcastle offices, and after visiting the important iron-making districts of France, Germany, Poland, and Austria, he took charge of their rolling-mills at Walker, and profited so well by his opportunities, and especially by the teachings of his father and of Mr. John Vaughan (later one of the founders of the great firm of Bolckow, Vaughan & Co.), that he was made manager of the Walker works in or about

Sep 1, 1905

By D. C. McLean, S. A. McKay

The purpose of this paper is threefold: 1) to describe actual ground control installations made at the various mines of the International Nickel Co. (Canada) Ltd mines in Sudbury, Ont. during a planned test program. 2) to suggest new ground control techniques which are now possible by the use of fully grouted bolts 3) to indicate the possible economic advantages to be gained by the use of resins and resin grouted bolts to control difficult ground conditions. Were a theme selected for this paper it would be: "Preserve the original roof in best condition possible by the use of smooth blasting techniques and fully grouted roof bolts — since the original rock is the best and cheapest material available for ground support." TYPES OF BONDED BOLTS As has been shown previously, there are several ways in which a bolt may be bonded. These are illustrated in Fig. 1 and 2. There are three general types of grouted bolts: 1) pretensioned, 2) post-tensioned, and 3) untensioned. The type which will be of most benefit to the user will depend upon the particular ground support problem involved. Despite the many arguments propounded for the necessity for using a tensioned bolt, ample evidence exists from actual experience that untensioned bolts can be effective in many instances. The outstanding characteristic of a grouted bolt is that it provides the user with a variety of rock consolidation techniques heretofore unavailable with conventional rock bolts. Many of the unusual characteristics of grouted reinforcing bar have been evaluated by researchers in the concrete structure field.' Underground application has largely been pioneered in the construction field, with especially good work being reported from the Snowy Mountains Hydroelectric Authority in Australia. Techniques developed there using cement grouted bolts are now being adapted in many large government construction projects in this country with excellent results. The ap- plications described in this paper are those in which Cyanamid's Roc Loc Mining Kits were used exclusively. SLUSHER DRIFTS AND FINGER RAISES (BOX HOLE BROWS, DASHES) A common mining problem especially where block caving methods are applied is that of maintaining the roof in slusher trenches particularly at the intersections of the trench with the feed raises (box holes) through which the large fragments of broken ore tumble. Typical sections are shown in Fig. 3 and 4. In Fig. 3, the drift is normally driven 7 ft wide by 8 ft high initially. The rock involved is a hard norite (diabase) which is usually competent but has "block cleavage". This roof has a tendency to fall out in large blocks when subjected to operating stresses. Depending upon the initial condition of the roof, the drift is either lined with 2 to 3 ft of concrete immedi-

Jan 1, 1964

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By E. H. Burdick

The difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals— pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of I .o per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1943

By AIME AIME

T'HE Columbia Section of the A. 1. M. E. took charge of the Western Mining Convention on Oct. 3, and the meeting was held under their auspices. W. L. Zeigler, chairman of the Section, called the session to order. The first paper on the program, "Lead Refining Practice at Bunker Hill Smelter," was presented in per-son by the author, A. F. Beasley, superintendent of the smelter. He pointed out the differences in the refining practice at Bunker Hill from other American refineries. The Bunker Hill plant was the first to adopt the liquation process for silver skims as developed in Australia. Details were given of operating practice with results. F. F. Colcord questioned the author in regard to the kind of metal best suited for kettles, which was said to be cast iron.

Jan 1, 1929

By Calvin Pierson, R. S. Dean, E. P. Barrett

Wrought iron and steel have been prepared from limonite, hematite, and magnetite ores by gaseous reduction, compacting and squeezing the resulting product at high temperature and finally melting the wrought iron so formed. The structure, analyses, mechanical and magnetic properties of the products are given. It is found that the structure of iron ores is best studied by subjecting them to gaseous reduction and using metallographic technique on the resulting sponge iron. In this way the cell structure of iron ore is clearly shown. The wrought iron made by heating compacted sponge iron to 1450" C., and forging, shows a cell structure inherited from the ore. This cell structure is further preserved in melting and casting the wrought iron. The probable relation of the properties of the materials to this inherited cell structure is discussed.

Jan 1, 1935

By A. B. Parsons

When the Seeley W. Mudd Memorial Fund was established in. 1929 the donors mentioned certain types of projects to which preference might be given in selecting those to he financed by the income from the Fund. One suggestion. was that the projects "be of particular benefit to young engineers." This modest little book meets this specification most aptly. It seeks to guide the engineer-particularly the young one-with the least loss of time and effort to the most convenient source of authentic information regarding any topic in which he may at the moment be interested. Knowing the best place to find the literature on a subject is almost as valuable-and far more practicable-than maintaining a library of one's own large enough to provide the information.

Jan 1, 1933

By Calvin Pierson, R. S. Dean, E. P. Barrett

Wrought iron and steel have been prepared from limonite, hematite, and magnetite ores by gaseous reduction, compacting and squeezing the resulting product at high temperature and finally melting the wrought iron so formed. The structure, analyses, mechanical and magnetic properties of the products are given. It is found that the structure of iron ores is best studied by subjecting them to gaseous reduction and using metallographic technique on the resulting sponge iron. In this way the cell structure of iron ore is clearly shown. The wrought iron made by heating compacted sponge iron to 1450" C., and forging, shows a cell structure inherited from the ore. This cell structure is further preserved in melting and casting the wrought iron. The probable relation of the properties of the materials to this inherited cell structure is discussed.

Jan 1, 1935

By J. E. Lawver

On the basis of both laboratory and pilot-scale tests, a newly developed high-tension electrostatic process is technically and economically feasible for the production of iron ore superconcentrates containing 0.02 to 0.20% silica at iron recoveries of 85 to 90%. The process can be used to recover both a superconcentrate and a pellet-grade concentrate, from a feed containing middlings, and the system is not unduly upset from changes in feed structure and composition. The adverse affect of excess quantities of material finer than 30 microns, i.e., above 10% in quantity can be avoided by a desliming step. Finally, because of the cost of drying, the best feed for the process appears to be dry-ground ores as well as spiral, flotation, or magnetic concentrates.

Jan 1, 1970

By Jack F. Havard, John S. Lagarias

When ore bodies are faulted or mill feed turns refractory, mining managers and engineers act vigorously to convert imminent failure into eventual success. The recent proliferation of onerous environmental regulations and restraints is likewise a threat to successful mining enterprise, in some ways more insidious and dangerous than the problems presented by natural obstacles. The regulatory burden has become so heavy that a pall of pessimism covers much of the mining industry. In this paper we frankly recommend an approach that does not just "make the best of it" but rather directs the whole environmental process: first, to improve planning, engineering, and operating procedures; and, second, to demonstrate the need for modification of laws and regulations which are intolerably burdensome to both the mining industry and the public.

Jan 1, 1979

By E. W. Codington

The pebble-phosphates of Florida occur in a district roughly bounded on the north by the 28th parallel, on the east by an irregular line running a few miles east of Peace river and on the west by the Gulf of Mexico, and covering an area of about 4000 square miles. There seems to be no reason why the deposits should not extend farther south along the gulf coast. That section remains unprospected, transportation-facilities being non-existent. It is not intended in this paper to discuss the geology of these formations; but a word as to their probable origin will be perhaps the best method of giving a correct idea of their present position. Starting with a low, flat surface, with even less of superficial undulation than appears at present, an im-

Jan 1, 1896

By Adam L. Wesner, A. C. Richardson

DURING World War II the demand for electrode carbon was greater than could be met by the supply of petroleum coke available for this use. It was believed that coke made from an extremely low-ash coal might be a suitable substitute for petroleum coke. Requirements for electrode carbon to be used for the production of aluminum are that the silicon plus iron content shall be not more than 0.14 pct of the coke. However, during the period when petroleum coke was in short supply, it appeared that relaxations of the specifications might be allowed to permit 0.4 pet iron plus silicon in the coke. For this work, the specifications were that the coal should contain less than 1 pet of ash, and the combined iron and silicon content of the coal should not exceed 0.28 pct. Heavy-liquid separations made on a number of coals showed that if certain size fractions of some coals were separated at low specific gravities the resulting float products would meet the required specifications. The objective of this work was to develop a continuous, commercially feasible process for producing low-ash coal. After consideration of various processes, the method chosen was a float-and-sink separation using a solution of calcium chloride as the separating medium. Eagle Seam coal was used for the experiments. The -10 +35 mesh fraction was found to be the most promising feed for producing the low-ash [ ] content coal. A batch of 30 tons of -3/8-in. coal was screened at 10 and 35 mesh; the yield of -10 +35 mesh was 20 pct of the feed. This fraction comprised the feed for the separation tests. In spite of the fact that this portion was screened a second time at 35 mesh, the coal still contained 16 pct that was finer than 35 mesh. Three-fourths of the undersize was in the -35 +48 mesh range. A representative portion of the -10 +35 mesh fraction was subjected to batch float-and-sink separations to determine the best gravity to be used in the continuous tests to obtain a high recovery of low-ash content coal. The heavy liquid used was a mixture of carbon tetrachloride and benzene which assured complete wetting of all of the particles. As usual in batch separations, adequate time was allowed for each separation so that even the near gravity particles had ample time to separate. The separations were made at increments of 0.01 sp gr from 1.25 to 1.28 and also at 1.32 and 1.59. Each specific-gravity increment was assayed for ash content. From these data it was concluded that 1.27 sp gr was best for the continuous separation of the coal. The products from the batch separation were composited into float 1.27 and sink 1.27 sp-gr fractions; these were assayed for ash, iron, and silicon. Table I shows the results of the batch separations. The composite float 1.27 fraction contained 66.04 pct of the total weight, and had an analysis of 0.79 pet ash, 0.073 pct iron, and 0.112 pct silicon, or 0.185 pct iron and silicon combined. These data are indicative of the results possible if a perfect separation is made at 1.27 sp gr under static conditions. Inasmuch as the method under investigation is a dynamic system these results could not be obtained. It remained to be determined, however, just how close to the theoretical results the actual continuous separation would be.

Jan 1, 1952

By L. C. Kern

This paper presents information on the use of a new propping agent (malleable aluminum particles) which has been used successfully for producing high-conductivity fractures. The conductivity of a packed fracture depends on the width of the fracture as well as the permeability of the propping material. It is significant that the flow capacity of a propped crack is often increased many fold by propping the crack with a sparse distribution of particles. However, the flow capacity of a sparsely propped crack can be limited by two phenomena: (I) crushing of the propping particles, and (2) embedment of the propping particles in the formation walls. Malleable aluminum particles exhibit interesting properties which tend to overcome these limitations. As high loads are applied to the particles they will deform slightly, rather than shattering. The deformation results in a greater bearing area against the formation wall. This reduces the stress on the particle and reduces particle penetration into the formation. The behavior of aluminum particles under load and the bearing capacities of serveral formation rocks have been measured in the laboratory. By properly using these data, as explained in this paper, the flow capacities of aluminum-propped cracks can be calculated for a variety of conditions. Aluminum particles have been used successfully in the field to prop fractures. Where high-conductivity fractures were needed, the aluminum-propped fractures have given greater well stimulation than could have been expected for conventional fracturing processes. INTRODUCTION The purpose of a hydraulic fracture treatment is to create a conductive channel from the wellbore out into the oil or gas formation. The word conductive is emphasized because we believe that the fracture conductivity (flow capacity) is one of the most important factors influencing fracturing results. Previous papers have pointed out the additional well stimulation that can sometimes be achieved by increasing fracture conductivity. Several years ago, we investigated in some detail the effect of fracture conductivity on productivity increases to be expeced from vertical fractures. Both electrical analog and theoretical studies of unsteady-state flow behavior were made. A discussion of the electrical analog equipment and some of the results of the study were given in a previous paper' by Dyes, Kemp and Caudle. Further details were given recently by McGuire and Sikora.5 Fig. 1 shows the remarkable influence of relative fracture flow capacity and length on well stimulation. Briefly, the study indicates the following. 1. High-permeability formations require high-conductivity cracks for best results. 2. The longer the crack, the higher the fracture conductivity required for best results. 3. If the conductivity of the crack is very large compared to the formation (i.e., flow is not being limited by crack conductivity), then the longer the fracture, the better will be the results. Judging from recently published articles,1,314 there is current interest in methods for obtaining high fracture conductivities. Hence, we would like to present in this paper a discussion of a new fracture propping process (use of aluminum particle) which we have used successfully to obtain highly conductive fractures. There are several factors which influence the conductivity of a propped crack. Conventional fracturing techniques frequently result in a crack completely packed with fracturing sand. For such conditions, the crack conductivity is the product of the width of the packed fracture and the permeability of the propping material. It is significant that a large increase in conductivity sometimes can be obtained by propping with particles which are distributed sparsely (less than a