Search Documents

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure' which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies' have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969

By P. Beardmore, A. H. Holtzman, M. B. Bever

Specimens of the alloy CU3AU in the ordered and disordered states were subjected to explosive loading at shock pressures in the range from 160 to 475 kbars. The resulting changes in the resistivity, stored energy, microhardness, and microstructure were determined. By comparing the effects of explosive loading on ordered and disordered specimens a separation of structura1 and configurational changes has been made. In the pressure range from 290 to 370 kbars, representing a small increment of strain, the degree of long-range order in the ordered alloy decreased sharply. This change is attributed to the generation of shear stresses in excess of the theoretical shear strength of the alloy. Disordered CU3AU under explosive loading behaves in a manner considered to be characteristic of fee solid-solution alloys generally. The response of metals to high-velocity deformation and, in particular, to explosive loading has attracted much interest in recent years.' In general, metals are substantially strengthened by the passage of shock waves although the permanent strains are small. Explosive loading induces this strengthening by causing the metal to undergo rapidly a transient strain in a narrow region, first in the shock front and then in the rarefaction wave, which releases the pressure. The transient strain is given by e = 4/3 In V/Vo, where Vo and v are the specific volumes in the uncompressed and compressed states.2 The process produces many defects, which account for the strengthening. For the investigation reported here, an ordered alloy was chosen because it was expected to give sensitive indications of the near-neighbor effects produced by shock waves. The ordered alloy CU3AU was of special interest because of past work on the effects of conventional deformation on this alloy.314 The disordered alloy was included as a standard for comparison and as an alloy typical of a solid solution containing short-range order. The effects of explosive loading were followed by measurements of the resistivity, stored energy, and microhardness, and by metallographic examination. EXPERIMENTAL PROCEDURES Preparation of Specimens. Part of an ingot of the alloy Cu3Au prepared previously4 was cold-rolled with several intermediate anneals in vacuum to a final thickness of 0.042 in. Specimens of dimensions 2.0 by 1.0 by 0.042 in. were machined from this strip. After a recrystallization treatment of 1 hr at 565oC, half of the specimens were disordered by heating in evacuated Pyrex capsules for 1 hr at 460°C and quenching into water. Although they contained short-range order, they will be referred to as 'disordered" to indicate the absence of long-range order. The rest of the specimens were cooled slowly from 380°C to induce long-range order. The grain size of the ordered and disordered specimens was 0.012 mm. Explosive Loading. This was carried out at the Eastern Laboratory, Explosives Department, E. I. du Pont de Nemours & Co., by a driver-plate procedure described elsewhere.2 Two ordered specimens were stacked alongside two disordered speci-

Jan 1, 1964

By Charles Trotter

An instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. Description The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time Lapse obtainable with the instrument designed for use in EX or AX size holes is I hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. Operation Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1949

By J. L. Meijering

Oxidation hardening of cylindrical and spherical specimens first decreases with depth below the surface, but then increases again as the center is approached. This is in agreement with the view that this change in hardness is mainly determined by the change in velocity of the oxidation boundary, which affects the dispersion of the oxide. WHEN a thick slab of silver containing 0.3 pct Mg by weight is internally oxidized, the hardness measured on a cross section is found to decrease considerably with distance from the surface.&apos; This phenomenon has been attributed to the diminution of the velocity of the oxidation boundary. The smaller this velocity is, the more slowly the free-oxygen concentration rises towards the concentration in equilibrium with the oxygen gas. And a small 0 concentration favors dissociation and thus conglomeration of the oxide. For instance, the hardness decreases more rapidly during long annealings in nitrogen than in air.&apos; Measurements by Gregory and Smith3 on sections through internally oxidized Al-silver wire showed a smaller variation in hardness, probably because the wire diameter was only 0.9 mm. Wood4 found a drop in hardness with depth in internally oxidized Al-copper strip, and also—by electron microscopy—the concomitant increase in Al2O3 particle size. Under certain circumstances internal oxidation leads to formation of rather irregular inner oxide films in the midst of dispersed oxide. This special sort of conglomeration—discussed in Ref. 5—is also favored by greater depth below the surface.3,5 In this paper hardness measurements in large diameter cylindrical and spherical specimens are described. Here the oxidation velocity* goes through ness initially decreases with depth but increases again towards the center. Normally, the diffusion coefficient D1 of oxygen is very large compared to D2, that of the dissolved metal. If, furthermore, the atomic fraction c2 of the latter is much larger than the O-solubility cl- but c2D2 << c1D1- the velocities in question are easily calculated2 to be: for the cylinder and for the sphere. Here p is the radial coordinate of the oxidation boundary and R the specimen radius, which in dilute silver alloys is constant, as no external oxidation occurs. These equations have been derived for a divalent solute; for nondivalent solutes c2 has to be multiplied by half the valency. The equations are not valid near the center. For which can be considered as a standard case,2 the Eqs [I] and [2] begin to yield U-values which are appreciably too high for p/R = 0.05 and 0.15, respectively. But at the v-minima they are still very good approximations. These minima lie at p = emlR= 0.37R in the cylinder and p = 1/2 R in the sphere. Other factors besides the velocity v will also influence the hardness. The oxide concentration cox is constant in a flat strip, apart from a narrow region in the middle,2 but in cylindrical and spherical specimens cox decreases steadily with depth. When C1 << c2 and c1D1 >> c2D2 one can calculate

Jan 1, 1961

By Edward E. Hicke, Charles A. Stickels

The dihedral angle of liquid-lead inclusions in solid nickel has been measured as a function of temperature from 371 to 816 C at zero pressure. and as a function of pressure up to 50,000 psi at 317 and 593 C. Thermodynamic expressions are derived for the temperature and pressure coefficients of interfacial tensions in this system. A method is presented for obtaining relative tempmature and pressure coefficients from dihedral-angle data, and the resulting values are used in conjunction with the thermodynamic relations to calculate excess properties of the solid-liquid interface. Defining the position of the solid-liquid interface by the condition that the excess concentration of lead is zero, the excess concentration of nickel and the excess entropy at the solid-liquid interface are: where y(593) is the interfacial tension of the nickel grain boundary saturated with lead at 593C and zero pressure. These values are considered reliable to within a factor of two. While similar calculations are not possible for the nickel grain boundary, it is shown that the expwimental results imply that the excess concentration of nickel at the boundary and the excess entropy of the boundary are negative. THE temperature and composition dependencies of interfacial tensions in metal systems have been reported by several authors in the last 15 years.&apos;-&apos; No measurements of the effect of pressure on inter- facial tensions in metals have been reported, although measurements made on nonmetallic gas/liquid and liquid/liquid systems suggest that a measurable effect should exist.6-l2 The purpose of these experiments was to determine the influence of temperature and hydrostatic pressure on dihedral angles in the Pb-Ni system. The equilibrium dihedral angle is expressed as a ratio of interfacial tensions by2: where 8 is the dihedral angle, yGB is the Ni-Ni grain boundary tension, and SL is the solid Ni-liquid Pb interfacial tension. Three sets of ex- periments were run to determine: a) the effect of temperature from 371" to 816°C on the dihedral angle at zero pressure; b) the effect of pressure up to 50,000 psi on the dihedral angle at 371° and 593°C. THERMODYNAMICS The properties of interfaces of most direct concern are the interfacial tension, excess concentrations of various components at the interface and the excess entropy of the interface, S°. These quantities are defined following Gibbs. Consider an interface separating phases a and 0. Construct two surfaces C, and C such that all properties of phase a remain uniform up to C, and all properties of phase 0 remain uniform up to C. The region between C, and Cp is the interfacial region. Let a "dividing surface", D, be constructed in the interfacial region such that it passes through all points "similarly situated with respect to the condition of the adjacent matter."l3 Surface D divides the interfacial region into a portion a&apos; adjacent to phase adjacent to phase . Let a closed curve, C, enclose an area A in D. Erect normal lines to D along C; these lines and the surfaces C,, Cp, and D then enclose volumes V and V&apos; in the two halves of the portion of the

Jan 1, 1964

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

By J. C. Uy, A. A. Burr

IN the primary solid solutions of zirconium-base alloys, there is a striking regularity of the effect of solute valence on the stabilization of the allotropic phases.1 The valences derived by pauling2 are for elements as they are bonded in the solid metallic state. Effects of variations in isotopes, alloying elements, and allotropes on their valences are difficult to determine and such data are presently unavailable. Pauling&apos;s values are somewhat empirical and approximate, but if some definite correlations can be found between those values and experimental observations, this will lend support to the tacit assumption that the possible variations in valence mentioned above are small. Pauling has amassed a large amount of evidence of such correlations. It is the purpose of this technical note to show another application of the Pauling valences and to offer a possible explanation for this observation. The relationship between the Pauling metallic valence of the solute and the stabilization of allotropic phases in zirconium is shown in Table I, which has been compiled from available data in the literature3 plus the results of work done at Rens-selaer Polvtechnic Institute.&apos; The chemical valences are included for comparison. It can be seen that a solute whose metallic valence is lower than that of the solvent tends to stabilize the a phase while one whose metallic valence is higher than that of the solvent tends to stabilize the 0 phase. It should be noted that, inasmuch as the Pauling valences are periodic with atomic number, this is tantamount to saying that the elements in groups I-A, 11-A, III-A, III-B, IV-B, V-B, and VI-B are a stabilizers while those in groups IV-A, V-A, VI-A, VII-A, VIII-A, I-B, and 11-B are ß stabilizers. The chemical valences do not show such consistency. Although the zirconium-rich end of the Zr-Au diagram is not available, it call be expected that gold, having a metallic valence of 5.56, would stabilize the ß phase. At absolute zero, the Fermi energy level is the criterion of equilibrium, i.e., the structure having the lower Fermi level will be more stable. Conse- quently, allotropic transformation occurs in a metal when thermal excitation raises the Fermi level to a point at which the atoms can be better accomodated by a different structure which yields a lower Fermi level.4-6 Thus in allotropic transformation, a change in structure occurs as a result of the change in the energies of the bonding electrons. Since the Pauling valence is the number of bonding electrons per atom, and these are the only electrons whose energies are affected by thermal excitation,* it can be inferred that the introduction of a solute which has a higher Pauling valence than that of the solvent raises the initial Fermi level; consequently, the transformation temperature is lowered. The converse is also true. The fact that at the transformation temperatures this statement is still fairly valid implies that the contribution due to the difference in specific heat terms of the two allotropes is comparatively small.

Jan 1, 1962

By Charles Trotter

AN instrument has recently been developed for determining the inclination and azimuthal direction of boreholes. This instrument is known as the Tro-Pari Instrument and is the invention of C. Trotter and G. Pajari of Sudbury, Ontario. DESCRIPTION The instrument is characterized by a unit mounted in gimbals and provided with a clockwork mechanism to clamp a compass to indicate azimuthal direction and simultaneously to clamp the unit in its plumb position to indicate inclination (Fig I). By means of a timing ring suitably calibrated in 5-min divisions, the unit may be set to lock after a lapse of time sufficient to allow the placing of the instrument at the desired point in the drill hole where readings are to be taken. The maximum time lapse obtainable with the instrument designed for use in EX or AX size holes is 1 hr 30 min which is considered to be ample time to lower to the greatest depths that may be drilled with this size of equipment. Larger sizes could be developed for larger diameter holes such as BX and NX sizes or the larger oil-well sizes and a correspondingly greater time lapse could be provided for. Up to the present time only the EX-AX size has been built. OPERATION Assuming a borehole is to be surveyed at 1000-ft depth and assuming it will take 30 min to lower the instrument to this depth, the timing ring is rotated through seven divisions which represent a time lapse of 35 min (5-min leeway) and is then returned to its zero position. This operation imparts energy to a spring which drives the clockwork mechanism. Simultaneously the compass needle is freed to swing to its magnetic north-south position and the encased mechanism is freed to hang plumb within a semicircular portion of the frame which is graduated in degrees after the fashion of a protractor. This semicircular protractor portion has a V-shaped notch at each degree division of its inner periphery. The instrument, now in its free position, is inserted in a bronze container made to suit the size of hole to be surveyed (Fig 2). Soft rubber washers are provided within the container to prevent undue shock. The container is connected to the drill rods with three 5-ft lengths of brass or aluminum alloy rods separating it from the steel rods in order to prevent distortion of the magnetic field. The assembly is then lowered to the desired point where readings are to be taken and is allowed to remain at rest until a period of time has elapsed slightly in excess of the time for which the timing ring was set. In the example cited above, when the 35 min has elapsed the compass needle is locked in its north-south position and the protractor locking pin is extruded and locks in the V notch opposite its plumb position. The device may now be removed from the borehole and it will remain in this locked position in spite of jarring or shak-

Jan 1, 1947

Time as a Factor in the Making and Treating of Steel. By John Johnston. (Howe Lecture) (T.P. 1478) Influence of Chromium and Molybdenum on Structure, Hardness and Decarburization of 0.35 Per Cent Carbon Steel. By R. F. Miller and R. F. Campbell. (T.P. 1345) Mechanical Properties of Iron-manganese Alloys. By F, M. Walters, Jr., I. R. Kramer and B. M. Loring. (T.P. 1369) The Instability of Low-expansion Iron-nickel-cobalt Alloys. By I. R. Kramer and F. M. Walters, Jr. (T.P. 1370) The S-curve of a Chromium-nickel Steel. By B. M. Loring. (T.P. 1383) A Magnetic Determination of the A3 Transformation Point in Iron. By B. A. Rogers and K. 0. Stamm. (T.P. 1388) Rapid Tension Tests Using Two-load Method. By A. V. de Forest, C. W. MacGregor and A. R. Anderson. (T.P. 1393) Effects of Scrap in the Blast-furnace Burden. By C. L. T. Edwards. (T.P. 1270) Temperature Gradients through Composite Carbon Columns and their Application to Blastfurnace Linings. By F. J. Vosburgh and M. R. HatFIeld. (T.P. 1363) Correlations of Some Coke Properties with Blast-furnace Operation. By H. W. Johnson. (T.P. 1402) The Technical Cohesive Strength and Yield Strength of Metals. By D. J. McAdam, Jr. (T.P. 1414) Effects of Eight Complex Deoxidizers on Some 0.40 Per Cent Carbon Forging Steels. By George F. Comstock. (T.P. 1417) Significance of the Bessemer End Point. By H. T. Bowman. (T.P. 1428) Structural Diagrams of Nickel Irons and Steels. By J. T. EasE and N. B. Pilling. (T.P. 1432) Carbides in Low-chromium Steel. By Walter Crafts and C. M. OFFenhauer. (T.P. 1436) Hardenability Calculated from Chemical Composition. By M. A. Grossmann. (T.P. 1437) Recrystallization of Silicon Ferrite in Terms of Rate of Nucleation and Rate of Growth. By J. K. Stanley and R. F. Mehl. (T.P. 1438) The Solubility of Carbon as Graphite in Gamma Iron. By R. W. Gurry. (T.P. 1440) An Evaluation of the Factors Affecting Iron Oxide in the Open-hearth Bath. By J. E. Gould and H. J. Hand. (T.P. 1442) Precision in Creep Testing. By J. A. Fellows, Earnshaw Cook and Howard S. Avery. (T.P. 1443) Lattice Relationships in the Decomposition of Austenite to Pearlite, Bainite and Martensite. By G. V. Smith and R. F. Mehl. (T.P. 1459) Rate of Nucleation and Rate of Growth of Pearlite. By F. C. Hull, R. A. Colton and R. F. Mehl. (T.P. 1460) Weight Change as a Criterion of Extent of Decarburization or Carburization. By R. W. Gurry. (T.P. 1470) Observations in the Making and Use of Sulphite-treated Steels. By E. L, Ramsey and L. G. Graper. (T.P. 1476) Diffusion in Metal Accompanied by Phase Change. By L. S. Darken. (T.P. 1479) Engineering Properties of Heat-resistant Alloys. By Howard S. Avery, Earnshaw Cook and J. A. Fellows. (T.P. 1480) Distribution of Manganese and of Sulphur between Slag and Metal in the Open-hearth Furnace. By L. S. Darken and B. M. Larsen. (T.P. 1481)

Jan 1, 1942

By J. P. Hammond, C. J. McHargue

THERE have been no publications on the wire texture, on the cold-rolled sheet texture, nor on the recrystallized sheet texture of vanadium. Since it has a body-centered cubic structure, it would be expected to show strongly preferred orientations such as are found in iron&apos; and molybdenum.&apos; The wire textures of body-centered cubic iron,3 tungsten," molybdenum,5 antalum,6 iobium,6 and brass6 have been found to have [110] directions lying parallel to the wire axis. Wires of iron,&apos; containing 1.95 pct V or 1.95 pct Si,7 and steel8 retain their texture upon recrystallization. Molybdenum9 and tungsttln&apos; wires retain their texture after recrystallization at low temperatures. A [loo] recrystallization texture has been reported for mo1ybdenum9 and for a Fe-Ni alloy (53 atomic pct Ni).10 The cold-rolled sheet texture for iron,&apos; mild steel," and molybdenum chiefly one in which the [110] directions lie parallel to the rolling direction and the (100) planes lie parallel to the rolling plane with a deviation from this position chiefly about the rolling direction as an axis. This paper presents the cold-rolled and the re-crystallized wire textures, and the cold-rolled and the recrystallized sheet textures for vanadium. The results show that the textures in vanadium are not significantly different from those reported for other body-centered cubic metals. The vanadium used in this investigation was the so-called "ductile" vanadium which has a nominal composition within the following limits:12 0, 0.05 to 0.12 pct; H, 0.001 to 0.004; N, 0.02 to 0.04; C, 0.03 to 0.07; and V, 99.8 to 99.9. The wires were formed by rolling annealed rods of 0.280 in. diam to 0.028 in., a reduction in diameter of 90 pct. The wires were then electrolytically etched to 0.005 in. diam and used as such for specimens. Annealed sheet was reduced 95 pct in thickness from 0.100 to 0.005 in. with a two-high, 4-in. diam mill using reductions no greater than 10 pct per pass. In order to avoid temperature effects, the sheet was allowed to cool between passes. X-ray specimens were made in the form of posts from the sheet. The sheet was mounted in a fixture and the edges were polished using metallographic technique. Each edge was alternately polished and etched during the last stages in order that all worked material would be removed. These post specimens were approximately square in cross-section. The specimens to be recrystallized were wrapped in tantalum foil, sealed in evacuated quartz tubes, and annealed at 1600°F. The X-ray data were obtained from transmission shots made with a 0.030 in. pinhole camera, and molybdenum radiation with a zirconium filter inserted between the specimen and film. The grain size was sufficiently small in both the cold-worked and recrystallized material to give satisfactory results with the specimens stationary. In order for the wire texture to be determined, transmission X-ray patterns were taken with the

Jan 1, 1953

By A. Lee Barrett

Mine power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectional-ized at approximately 2500 ft by means of switches. All, or at least most branch .circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, therefore a fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does considerable damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting. from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V opera-tions, and at I mile intervals or less, in 250V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1949

By A. Lee Barrett

MINE power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectionalized at approximately 2500 ft by means of switches. All, or at least most branch circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, there- fore n fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does consider- able damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V operations, and at 1 mile intervals or less, in 250 V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1948

By D. C. Jillson

BRIDGMAN1,2 melted metals in a graphite or hard glass tube and lowered the tube through a furnace to make it cool from one end only. Because of the difficulty of eliminating all vibration of the mold, others have raised the furnace instead. Neither way seems as desirable as a setup with no motion of either the mold or the furnace. A furnace in which both the shape and the slope of the temperature gradient could be controlled and varied over a wide range and in which such a gradient could be moved from one end of the furnace to the other, freezing the specimen from one end to the other, at any desired rate, all by means of isolated external control, seemed to offer definite advantages. In addition to eliminating the possibility of vibration due to moving parts, it might also give better control over the direction and rate of heat flow. Such an apparatus was assembled and is shown schematically in fig. 1. Equipment Furnace: A clay-carborundum tube of 3 1/2 in. ID with a % in. wall thickness was used as the core. This had a main winding of No. 12 B.&S. gauge Nichrome V with some compensation for heat loss at the ends. Taps to this winding were made at points 12 in. from each end. Fig. 2 shows details of this winding and of the two end windings. Each end winding was wound over Micanite over the main winding. No. 15 B.&S. gauge Nichrome V was used for these, and again taps were supplied at two inter-mediat,e points on each. The tube was supported in an 18 in. OD black iron shell with brick insulation. The input to each of the windings was regulated by means of a variable transformer. Temperature Regulation: A chromel-alumel thermocouple located near the furnace wall in the center of the furnace was connected with a Celec-tray controller, type PIC, 300" to 900°C range, which opened and closed a shunt across an external variable resistance in the main winding circuit. An "anticipatory response" device also was incorporated to minimize the cyclic effect of the control mechanism. Eleven survey couples in a common pyrex glass protection tube were located near the furnace wall and spaced 2 in. apart. The couple leads went to a common reference junction box where they were connected to copper leads from a selector switch which, in turn, was connected to a type K potentio-meter. This arrangement permitted rapid temperature surveys. The knob on the controller dial was replaced with a threaded brass spool turned at a controlled rate by a thin iron wire one end of which was attached to a gear train and the other to a small weight heavy enough to prevent slipping of the wire on the spool. The gear train, driven by a 1-rpm Telechron motor, contained a series of different sized interchangeable gears and threaded drums permitting a range of travel speeds from 0.10 in. per hr up to a hypo-

Jan 1, 1951

By E. DeGolyer

The problem of good engineering practice and. of good conservation practice in oil production is that of keeping gas in solution. This can best be done by producing a field as a water-drive field. Some degree of water drive is believed to be present in most fields but in the past most fields have been produced too rapidly to allow water drive to be effective. Ultimate recovery should be So per cent greater for fields produced by water drive over that from gas-expansion fields. Wide spacing will permit fields of low-degree water drive to be produced effectively as water-drive fields. INTRODUCTION NEGLECTING all the complicated scientific and technical argument that leads to the conclusion, the solution of the problem of good production practice, of good engineering practice, and of good conservation practice in oil production is to keep gas in solution. This can best be done by producing fields at a rate low enough to make effective the water drive, which exists, it is generally believed, to a degree great enough to be made effective in more than 80 per cent of the fields of the United States. Oil is being so produced in the Ten Section field of California; the Hobbs field of New Mexico; the Yates, Hastings, Friendswood, Anahuac fields and the main sand of the Conroe pool, in Texas; the Magnolia pool in Arkansas, and doubtless in many other pools. The measures of success in the efforts to achieve the solution of the problem are the maintenance of bottom-hole pressure and the prevention of an increase in gas-oil ratio. Some decline from the original bottom-hole pressure and the production of some gas are essential. A pressure gradient from the reservoir to the well is necessary and at least as much gas must be produced as that in solution in a barrel of oil. Once the optimum pressure and the gas-oil ratio have been established, they should be maintained. How common is water drive in oil and gas pools? General opinion is that some degree of water drive is almost universal. Theoretically, this conclusion appears to be a sound one. According to our present understanding of the processes of sedimentation, we would expect to find all sands or sandstone charged with connate water unless it had been displaced by some other fluid, such as fresh water percolating into the beds at the outcrop, or oil and gas, or gas only, in reservoirs. The fact that the original pressure of the fluid system in most reservoirs is approximately that of the hydrostatic head of water for the corresponding depth indicates that the sands are charged with water, and common experience in drilling into the extensions of the porous zones beyond the reservoir is to find them watercharged. The very fact that oil and gas pools have substantial pressures in their original undisturbed state indicates either that a reservoir is a rigid, closed system, a con-

Jan 1, 1941

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated mineral-spyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying 1 per cent is considered good grade; 0.7 to o.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent WO3 is exceptional. Inasmuch as buying specifications demand a 60 per cent WO3 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 6o to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent W03, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By T. V. Falkie, D. R. Mitchell

Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial and error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in coal mine haulage. This paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment, and is approached primarily from the standpoint of scheduling of the main haulage. Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial-error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in mine haulage. In many physical cases several probability distributions interact with each other in special ways, and it is not possible to solve for their combined effect in a mathematical equation. This is often true in the case of mine haulage, where such variables as number of empties or loads per trip, travel times, and number of cars or tons produced in a given time are probabilistic. By using a simple example of one secondary haulage segment of a large underground haulage system, this paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment. This is the type of preliminary research that will be needed as a first phase in any major haulage study, whether it be a relatively simple economic analysis or a plan for complete automation. The problem of optimization has been approached primarily from the standpoint of scheduling of the main haulage. It is evident that the method of proba-

Jan 1, 1963

By Sherwin F. Kelly

THE joint meetings of the Mining Geology Committee and the Society of Economic Geologists proved to be deservedly popular, and the interesting papers drew an attendance which strained the capacity of one of the large meeting rooms.. As might be expected these days when even the Supreme Court can&apos;t keep away from the subject of gold, the discussions opened on Thursday morning with several papers devoted to questions of structural and mineralogical relationships of the deposits of this metal. The presentation of Ira B. Joralemon&apos;s paper, "Veins and Faults in the Bralorne Mine," by Reno Sales, elicited considerable discussion on the relation of mariposite to gold, and the situation of the gold deposits with respect -to the Coast Range batholith. H. V. Warren stated that lie had observed mariposite always to be associated with gold in this region, but that gold was not always associated with mariposite. He pointed out that there is a series of veins on the west side of the batholith with a different mineralogy that, because of their richness but small size could quite easily make good, small mines. John A. Dresser concurred in this, and said lie thought this region was one of great promise for the mining geologist. He also reported having found mariposite associated with gold values below commercial limits, in the Appalachian regions.

Jan 1, 1935

R. V. NorHis, Wilkes-Barre, Pa. (communication to the Secretary*) : The electric-haulage plant of the Short Mountain Colliery of the Lykens Valley Coal Co., mentioned by Messrs. Stoek and Harris as the earliest underground electric plant in the United States (and, I believe, the second in the world), was started July 23, 1887. The plant, designed by W. M. Schlessinger, consists of two motor-cars, each weighing about 5 tons and equipped with a 32-h.p. Union Electric Go. motor. The original general construction of the motor-cars is shown by Mr. Stoek; but they were rebuilt, the same year, with some important improvements in design; and, except for strengthening the frames and replacing the original pig-iron weights by a casting, they have not been greatly changed since that time. The generating-plant consists of two Union Electric Co. dynamos of 65-h.p. each, driven by an old 18- by 48-in. plain slide-valve engine; the ordinary voltage is 450 and the amperage varies from 40 to 200; the average indicated h.p. of the engine is about 75, with a steam-consumption of about 75 lb. per i.h.p. per hour; and as the cost of steam at this colliery is 8.11 cents per 1,000 lb.,the steam-cost per day is about $4.56.

Jan 1, 1904

By W. D. Von Gonten, R. L. Whiting

Regression analysis was used to correlate the physical properties of 478 sandstone and 90 carbonate core samples. Porosity, permeability, electrical formation resistivity factor, capillary pressure and the sonic velocity of the shear and compressional waves were measured. Prediction equations for porosity, permeability and electrical formation resistivity factor were found which should be useful in understanding the relationships between the physical properties of porous media in formation evaluation. INTRODUCTION The physical properties of porous media are important to the petroleum engineer and geologist. To evaluate fully the potential and behavior of a subsurface formation such as a petroleum reservoir, certain physical properties of the porous medium must be known. The problem of accurately determining physical properties of subsurface formations has not been solved because many determinations must be made by indirect measurements and because of the difficulties caused by complex pore structure and presence of clays in most naturally occurring porous media. Due to the difficulty in measuring some of the physical properties of porous media, it would be advantageous to be able to predict a certain physical property of a rock from other physical properties of the rock which could be measured more easily and more accurately. Since most potential reservoir rocks are heterogeneous, relationships between the physical properties are very complex and thus far no satisfactory correlations based on theory or laboratory models have been developed. It appears that empirical relationships obtained by measuring the physical properties of a large number of samples of naturally occurring porous media and applying regression analysis to develop equations for one physical property in terms of other rock properties is the best approach. REVIEW LITERATURE The three physical properties used as dependent variables for correlating purposes were porosity, permeability and formation factor. Since formation factor is more difficult to determine, a brief review of the literature is provided on this property. The first work on determining formation factors was published by Archie1 in 1942. He defined this property of a porous medium as F - Ro/Rw......(1) where Ro is the resistivity of the porous medium when completely saturated with a brine of resistivity Rw. Archie found the best correlation between formation factor and porosity was the following equation, where is the porosity fraction and m is the constant characteristic of the rock. The value of m was 1.3 for unconsolidated sand packs, and ranged from 1.8 to 2.0 for consolidated sandstones. In 1950 Patnode and Wyllie2 and De Witte3 observed that the formation factor as determined by Eq. 1 was valid only when the porous medium contained no conductive solids such as clay or shale. When conductive solids are present the formation factor is also dependent on the resistivity of the saturating fluid. Therefore, in samples containing conductive solids the formation factor decreased as the resistivity of the saturating fluid increased. Because of this. the measured formation factor was called the apparent formation factor and was designated Fa. Patnode and Wyllie proposed the following equation,

By Richard R. Bains

"When l hear - I normally remember 10 percent When I hear and see - I can remember 15 to 25 percent When I hear, see, and do - I usually remember up to 50 percent" While this is not a truism in relation to each and every individual; on the average, this is the case. If we use this as a premise in training operator and maintenance personnel, then it must be obvious that we can&apos;t rely on a mere presentation, even one which includes the needed classroom participation and/or hands on work, to do a thorough job and to make this personnel totally proficient - 100 percent proficient. We have to have some other device some other means to make this a continuing process, a process wherein the people can grow in knowledge while performing their normal duties. We have to feel that the words "normal duties" are the key to the whole program. If you would ask a crusher operator what his duty is, he might say "To run this crusher so that we produce 250 tons per hour of a minus 13mm (minus 1/2 ") product." A maintenance man could say "To fix the unit when there is a problem." Both of these answers are legitimate but, they are only a part of the total picture. In order for each of these individuals to do the best job, he must know not just the specifics about the machine he works with or on - he must know the interrelation of all the machinery in the crushing circuit - how the efficiency of each machine affects the others - why a minor problem on one piece of equipment can generate a major problem for another unit which follows it or precedes it. In short, you cannot separate machine operation and maintenance from the application of the equipment in the crushing circuit - and obtaining this knowledge must be a part of the normal duty of crushing plant personnel. As an example a crusher - any crusher - is designed to crush oversize material. It is not designed to accept feed which is already at or less than the required product size. If sized material goes to the crusher, increase wear results by using the crusher as a chute or the crushing chamber can be clogged up with the fines. This latter point is particularly true with cone crushers, especially in the third (Short Head) stage of crushing. When a Gyradisc is used (fourth stage crushing) it is even more critical that the product be removed before the material goes to the crusher. The crusher cannot control this - the screen ahead of the crusher does. The screen must be of adequate size and be functioning properly to allow the crusher to work at optimum. Screening is both an art and a science. Since there are so many variables which affect the output of the screen, it is always best to have a screen which is larger than the sizing calculations dictate. The screens are the most important elements in the circuit. Without screens, specification materials cannot be made and the size of the screen will ultimately aid or hinder your ability to get the most production possible out of the plant. There is a formula available from all screen manufacturers which is designed to calculate the proper screen size. It takes into consideration the

Jan 1, 1982