Search Documents

By R. J. Caro

The Anaconda phosphate plant was put into operation in the fall of 1923. Its present daily operating capacity is approximately 170 tons of treble superphosphate and 16 tons of phosphoric acid analyzing 42 pct P2 O5 and 52 pct P2 Os, respectively. As a result of the continued increased demand for phosphates, Anaconda decided in 1947 to expand the plant's daily output to 270 tons of treble superphosphate and 54 tons of phosphoric acid. The present daily plant intake is 335 tons of wet (footwall) phosphate rock analyzing 31.7 pct P² O5 and 0.28 pct V² O5. The rock is shipped from Anaconda's mine at Conda, Idaho, in open railroad cars, having been crushed to pass 3/8 in. mesh at the mine.' The expansion program will require an increased intake of 300 tons of rock per day. The hanging-wall rock anaIj-ses approximately 30.5 pct P2 O5 and 0.11 pct V² O5, and will be beneficiated in a new washing plant under construction

Jan 1, 1950

By Emil-Paul Lorenz

Considered as a whole, the mineral resources of the Turkish Republic (Anatolia) are in their untapped virgin state, and the little development shown is not the result of modern systematic geologic exploration but the continuation of the ancient open-pit mining methods of the Orient. When I came to Turkey in 1924, I found myself confronted by a formidable task because of the lack of preliminary geologic mapping. Today this condition has not essentially changed; less than one per cent of the country is covered by topographic mapping adequate for modern requirements. However, I was able to bring a semblance of order in a presentation of the mineral deposits of this country, by tracing the story of the mineral deposits that showed surface evidence of their existence. At present only the easily discovered mineral deposits of coal, copper, and lead-silver ores are being exploited. In the case of coal, of 3,000,000,000 metric tons available, only 100,000,000 have been mined. The same is also true for copper, lead-silver, and other ores, as shown in Table 1.

Jan 1, 1948

By George C. Stone

AS most of you probably know, Australia has had many strikes. The two places that had the worst reputation were the Broken Hill mines and Port Pirie, where the smelter was located. About four or five years ago, the smelter changed hands. The new proprietors - immediately endeavored to get on better terms with the men and made such progress in that respect that, the men came to them and said, "There is no use giving us any more money. You have just raised our pay one- bob a day, but the store-keeper and the boarding-house keeper have raised their prices. The boarding housekeeper raised our board three bob a week and the storekeeper took the rest of it and we are no better off." Learning that what the men needed most was firewood wood the company bought the wood on a tract of ground across Spencer's Gulf and- sent men over to cut it. The wood was brought to the works and given to a man to cut up. He thought he had an easy job and loafed, but when the committee representing the men discovered that his loafing added to the cost of 'the wood, it promptly disciplined him and made -him work as he had never worked before. The next question that arose was the distribution of the wood. The committee got bids from several cartmen whose prices varied from about two to five shillings. It gave the work to the next to the lowest bidder. The fact that if delivering the wood cost more, the user would have to pay for it, was an entirely new idea to the men.

Jan 1, 1920

By John M. Lovejoy

NATURAL resources become a source of wealth as they are exploited and made available to the people in usable form. Experience has taught us that Nature does not readily give up her treasures, but the ingenuity of man in the field of techologic progress is required to find and efficiently exploit these resources. History has also demonstrated that with advancing technologic knowledge the. world has become progressively richer in its resources. Those that could not be commercially exploited are now being turned to beneficial use. Through expanding technology and the use of substitutes and synthetics, availability of the world's sources of natural wealth is today many times that of a hundred or a thousand years ago. And so it is with petroleum. Technology is also the great multiplier of our petroleum resources. Through improvements in the art of finding, drilling, and producing, our ability to meet rapidly increasing demands over the last quarter century has been maintained. On the other hand, had our

Jan 1, 1944

By J. E. Steiner, J. M. Hodge, M. A. Orehoski

Ingots of four steels (1045, 1080, Ni-Mo-V, and Ni-Cr-Mo-V) were cast at pressures varying from about 1 to 760 mm of mercury, so as to obtain a range of hydrogen contents in each steel. The susceptibility of these steels to flaking was evaluated by cooling hot-rolled blooms at a range of cooling rates, varying from water quenching to slag cooling, and studying the occurrence of flaking as a function of cooling rate. The steels exhibited differences in susceptibility to flaking, and a tlzreshold value for hydrogen content for each steel was found, below which the susceptibility was very low and above which the susceptibility increased markedly with increasing hydrogen content. Mechanical property evaluations, metallogvaplzic exantinations, and X-my diffraction determinations o,t retained austenite were made on samples from the blooms. A mechanism of flaking which is consistent with the observed behaviors, the effects of hvdrogen content, and the differences in susceptibility among the steels investigated is postulated, based on the results of mechanical property evaluations and metallographic and X-ray diffraction studies. ThE important role of hydrogen as a factor in the occurrence of "flakes" or "hair-line cracks" in steel has now been established by many investigations. These have included investigations by steel producers and forging manufacturers, to whom the prevention of flaking is a very real and serious problem, and many research studies aimed primarily at establishing the mechanism of this behavior Several investigators3 have reported that steels cast at reduced pressures (absolute pressures of about 1 mm) not only are low in hydrogen content but are essentially insensitive to the formation of flakes. These investigations have shown that a general relationship exists between hydrogen content and susceptibility to flaking. The difficulty of obtaining suitable samples of steels of a given composition with the desired range of hydrogen contents, particularly in the relatively large sections in which flaking most commonly occurs, has been the principal obstacle to quantitative evaluations of these relationships. Steels with intermediate hydrogen contents between 1 ppm, and the 4ppm or higher of air-cast steels are generally not available in commercially produced steels. Laboratory procedures, in which the hydrogen is introduced into solid steel samples by heating in a hydrogen atmosphere under pressure, generally involve a limitation in the size of the sample which can be treated, and thus are not representative of the behaviors in large sections. The availability of a facility at the South Chicago Works of U.S. Steel, in which several ingots could be cast from a single heat of steel at total air pressures ranging from 0.25 to 760 mm of Hg, has made it possible to overcome this obstacle and to obtain ingots of a given steel covering the intermediate range of hydrogen contents desired. These ingots, furthermore, are of a size suitable for the production of product with section sizes large enough to be representative of the products in which flaking most commonly occurs in commercial production. In these experiments, this facility was used to study the relationships between hydrogen content and the susceptibility to flaking of four steels, two plain carbon steels at 0.45 and 0.80 pct C and two low-carbon alloy steels representing a medium and a rather high hardenability level. These flaking studies were supplemented by evaluations of mechanical properties and by metallographic studies on samples from the blooms, in order to obtain pertinent information on the factors other than hydrogen content which influence the susceptibilities of these steels to flaking. Based on the results of these tests, a mechanism for the initiation and propagation of the flaking cracks, which is consistent with the observed behaviors, is postulated. MATERIALS AND EXPERIMENTAL WORK Steelmaking and Conversion. To provide material for the investigation, five 29- by 35-in., hot-topped, big-end-up ingots were cast from each of four 80-ton, basic electric-furnace heats of four different steels (a 1045 steel, a 1080 steel, a Ni-Mo-V steel, and a Ni-Cr-Mo-V steel). A double-slag practice was used on all steels and the two plain carbon steels were Si-A1 deoxidized with an addition of 2 lb of A1 per ton, while the Ni-Mo-V and Ni-Cr-Mo-V steels were deoxidized only with silicon and

Jan 1, 1964

By Charles Will Wright

THE economy as well as the living standards of a country depends largely upon adequate supplies of raw materials at reasonable prices. Geological and climatic conditions responsible for the occurrence of commercial minerals and the growth of raw agricultural and forest products are so varied in different parts of the world that no country can be self-sufficient. The world is rapidly shrinking because of improvement in transportation facilities, but populations are steadily increasing and so are the needs for a greater production of raw materials and for their more equitable distribution. Too many barriers between nations prevent free access to the main sources of supply of the raw materials vital to neighboring nations and it is just such barriers that are often the cause of friction and even war. The International Trade Organization is doing a commendable job in helping to. break down barriers and to reduce friction, and we should now find ways to facilitate access to these sources of supply and encourage more efficient and greater production of the raw materials so urgently needed throughout the world. This cannot be done by individual selfish governmental agencies, influenced as they are by politics, nor by socialistic governments attempting to nationalize industries. It can be done efficiently only by the free individual through private enterprise properly protected against adverse governmental action. This protection can be supplied by the World Bank.

Jan 1, 1948

By Charles W. Frey

SUCCESSFUL mining today means proper mechanization. Before any mine can begin production on a paying scale, some machinery must be installed. There must be pumps to remove water, fans and blowers to provide proper ventilation, elevators and hoists to raise materials, and a source of power to turn the countless wheels on which the world's mineral supply rolls from its earthhound source to the market. Only the prospector with his burro and the anthracite "bootlegger" continue to mine without mechanical aid, and with the recent years even these can be discounted, for the burro has given way to the Model T, and the "independent" coal miner must have a truck to haul his coal away. The few types of machinery mentioned above are but a beginning. The

Jan 1, 1938

By Edward Steidle

TWO years ago the Committee on Latin American Education Relations, Mineral Industries Education Division, started a study of mineral industries education in the Latin Americas. Information was obtainable only with great difficulty. Some information was available piecemeal but no complete resume had ever been assembled. Initial assistance was gained from the United States Office of Education and the Pan American Union. This, and first-hand knowledge of the writer, provided a list of colleges and universities which were believed to offer work lead. ing to a degree in one or more branches of the mineral industries. Detailed information could be obtained only by direct contact with each university through air mail service. Questionnaire letters were sent to officials of 34 colleges and universities. Twenty-one gracious replies were received. Fourteen of the colleges and universities concerned offer curricula in mining, five in metallurgy, three in petroleum, seven in geology, one in geographical engineering, one in topographical engineering, and one in geophysics. Two institutions offer advanced training in petroleum engineering. No institution offers any courses under the caption of ceramics or fuel technology.

Jan 1, 1945

By George E. Roberts

THE gains of society from the state of primitive conditions in the past to the standard of living which prevails in the advanced countries today have been accomplished mainly by the increasing productive capacity of the population under the leadership and services of the engineer. Without improvements in the arts and industries the growth of population tends to place succeeding generations always at a disadvantage. In this country we have been exploiting with reckless prodigality a wealth of soil and minerals and timber that has been in preparation for thousands of years. We know that the prices of all national products have been advancing, and were on a rising scale even before the phenomenal increases resulting from the war. Over against this depletion of natural wealth we have the influence of improvements made in the methods of production and distribution-and the accumulation of wealth in the form of productive equipment. The net result of these opposing influences determines whether society moves forward or backward.

Jan 1, 1926

Jan 1, 1967

Aase, Glenn D., (J'40) Jr. Met.. American Smelt. k Refin. Co., Selby, Calif. Abadie, Henry G., (J'43) Petr. Engr., Avenal, Calif. Abbott, Clarence E., (M'04) Civil Engr., V.P.. Tennessee Coal, Iron & R.R. Co., 1542 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., C.O., Pitts¬burgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D.. (M'32) Min. Engr., Supvr. Engr., R.F.C.Lee Angeles, Calif. Abele, Louis T., (M'31) Route No. 1, Adameville, Tenn. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co. Ltd., Vatukoula, Fiji Is. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Kans. Abernathy, Jack H,, (M'40) Asst. Cenl. Supt. of Prod., Sunray Oil Co., 11th Floor, Philtower Bldg.. Tulsa 3. Okla. Abernethy, D. Carl, (M'44) Min. Engr. Rm. 3217, N. Int. Bldg., Washington, D. C.

Jan 1, 1944

By H. N. Eavenson

Prior to 1907 nearly all coke was made in beehive ovens, and most of the gas produced was made in the old-style gas retorts, and while there were a few coke plants in southern West Virginia, southwest Virginia and Kentucky operating on high-volatile coals the proportion of the total product made by them was small and usually was used locally. The greater part of the coke made, and the coal gas produced, came from the Pittsburgh seam of western Pennsylvania and northern West Virginia, which was then regarded as the standard coking and gas coal of the country, and the best coal available anywhere for these purposes. With the advent of the byproduct oven and the building of coke plants at the furnaces, the restriction of the use of one grade of coal for making coke was removed and the use of mixtures of low-volatile and high-volatile coals began. The change in the locations of the coke plants removed the necessity of using Connellsville coal and also made sources of gas available to the public utilities other than of their own manufacture. Most of the first oven plants were built at points distant from the Connellsville region and this afforded an opportunity for the use of coals from the southern Appalachian fields, which were then at approximately equal distances from the ovens. Since that time development has been made on a number of seams of coal of great purity in southern West Virginia, southwestern Virginia and eastern Kentucky, which have been largely used for gas, cokemaking and metallurgical purposes where low amounts of ash, sulfur and phosphorus are determining factors. These coals are much lower in the objectionable elements than most of the coal shipped from the Pittsburgh seam, or than any northern coal, and when blended with low-volntile cod produce coke in byproduct ovens that is not excelled for any purpose by any coal mined in this country, and is equaled very seldom. Coal from several of these scams is shipped in great quantities without beneficlation and is lower in ash and sulfur than any but the best washed product from the Pittsburgh seam in the north. The writer has made a study of these coals to ascertain their relative qualities and the areas and reserves of coal available in each of them. No attention has been paid to the coals of Alabama, which do not compete with any of these coals, and no coal of equivalent quality is found in

Jan 1, 1934

By D. D. Dunlop, J. R. Welker

The growing interest in the use of CO, in crude oil recovery increases the need for data on the effect of CO, on hydrocarbon physical properties. Data are presented on the solubility of CO, in various dead oils, the swelling changes in CO2-oil solutions and the effect of CO, on dead oil viscosity. This latter property shows the most pronounced effect, with viscosity reductions up to 98 per cent of the uncarbonated viscosities. An empirical method of estimating the viscosity of carbonated oils is presented. The apparatus and procedures used are described in sufficient detail to allow others to make similar studies. INTRODUCTION The effect of dissolved carbon dioxide on the swelling and viscosity reduction of specific hydrocarbon oils has been observed and recorded by a number of investigators.'- me object of this paper is to offer a means of predicting these effects for crude oils free from natural gas, using the dead state viscosity and gravity of the crude oils. The CO, solubility and swelling of numerous crude oils were determined in a visual cell at various pressure levels. The viscosity of the oils carbonated to various pressure levels was then determined by measuring the pressure drop across a capillary tube. From these data, the physical properties were correlated empirically. The resulting correlations allow the prediction of CO, solubility, swelling and viscosity reduction if the dead state gravity and viscosity of the oils are known. SOLUBILITY AND SWELLING MEASUREMENT EQUIPMENT AND PROCEDURE A high pressure visual cell was installed in a constant temperature cabinet. A test gauge was attached at the top of the cell for pressure measurement, and a line was run through the cabinet wall to a wet test meter which was used for volumetric measurement of the gas. The first step in making a test run was to put the oil in the cell up to a level about half to two-thirds of the total volume. This required about 50 to 65 ml of oil. carbon dioxide was then bubbled up through the oil for a time during which the pressure of CO2 in the cell was kept above 800 psia. Saturation of the oil with CO2 at this pressure and ambient temperature was confirmed by slowly bleeding CO2 through a valve to the atmosphere. If the oil was completely saturated with CO2, bubbles of gas would form in the oil at the first small decrease in pressure. If the oil was under-saturated, no bubbles formed until the pressure was decreased to the saturation pressure existing in the oil. If this saturation pressure was lower than that desired, more CO2 was bubbled through the oil until the desired level was reached. After saturation at ambient temperature was completed, the cabinet temperature was adjusted to the desired level and the cell was allowed to reach temperature equilibrium. After temperature equilibrium was reached, the pressure was again decreased slightly, and the oil again checked for full CO2 saturation at the cell pressure. The pressure now had changed because of the difference in solubility of the CO, in the oil at higher temperatures and the expansion of CO2 as the temperature increased. The outlet tube from the cell was then connected to the wet test meter and the CO2 was allowed to flow slowly out of the cell and through the wet test meter at ambient temperature and pressure. The water in the wet test meter had previously been saturated with CO2 at ambient temperature and pressure by allowing CO2 to flow continuously through it lor a period of several hours. The gas flow was stopped at several pressures during the run and the cell was allowed to come to equilibrium; this made possible the measurement of solubility and swelling data at the intermediate pressures. The volume of the oil in the cell was recorded at each of the equilibrium pressures in order to obtain swelling data. DATA AND RESULTS The solubility of CO2 in the oil was calculated by the relationship V — V, where R. = solubility of CO, in crude oil, cubic feet of CO, measured at 60F and 1.0 atm/ bbl of dead state oil at the temperature under which solubility was measured, V, = volume of gas released from the cell between the saturation pressure and zero pressure, corrected to 60F and 1.0 atm, cu ft, V, = volume of CO: contained in the gas space above the oil, corrected to 60F and 1.0 atm, cu ft, and V, = volume of the dead oil in the cell in bbl at the temperature of the run. The volumetric data of Sage and Lacey' were used to calculate V., from the volume of CO2 at high pressures. The swelling factor was calculated as where V, is the volume of the C0,-

By Klaus-Peter M. Hanke

INTRODUCTION In early 1979 Jim Walter Resources, Inc. (JWR) of Brookwood, Alabama approached TMCI Construction, Inc (TMCI) to make a proposal on a program that involved the sinking of up to 10 ventilation shafts of approximately 6.7 m (22 ft) diameter and ranging in depth from 500 to 700 m (1650 to 2300 ft) for the JWR coal mines in Alabama. At this time TMCI was already constructing the first spiral underground bunker (capacity 2000 tons) in North America for the JWR organization at their No. 4 mine in Alabama. The TMCI proposal was based on the use of the mos modern large diameter shaft boring machine rather than sinking the shafts using the conventional drill blast-muck technique. The proposal was made based o: the experiences by the parent company, Thyssen Schachtbau, which has been using this type of machin in Germany for shaft boring since 1971. As a result of the TMCI proposal JWR issued a purchase order to TMCI for the construction of four 6.7 m (22 ft) diameter, concrete lined, unfurnished ventilation shafts ranging in depth from 500 to 700 (1650 to 2300 ft). An order was thus placed with WIRTH Machinen- and Bohrgeraete Fabrik GmbH, in Germany for the manufacture of a model 650/850 E/Sch "Schachtbohrmaschine" (Vertical Shaft Borer = V-mole which arrived on site in Alabama in early 1981. The first V-mole GSB 450/500 was introduced in Germany in 1971 and was capable of enlarging in one step a pre-drilled 1.2 m (4 ft) pilot hole to 4.5 - 5.0 m (14.7 - 16.4 ft). This machine has sunk 9 staple shafts and deepened one surface shaft for a total of 2360 m (7740 ft) of shafts. On the last shaft boring operation in 1978 the machine was converted as an experiment to drill without a pilot hol using a hydraulic pumping system to remove the cutting debris. A second generation machine, the SB VI 500/650, was introduced in 1977 for enlarging the pilot hole to a range of 5.0 - 6.5 m (16.4 - 21.3 ft) diameter. This machine is still in operation and has already drilled well over 2000 m (6500 ft) of shaft. The third generation of V-mole, the SB VII 650/85( for diameters from 6.5 to 8.5 m (21.3 to 27.9 ft) was: commissioned in May 1980 and has been used for two surface shaft deepenings totalling 606 m (1990 ft) with another scheduled for 1982. The main advantages favouring the use of such V-moles were identified as: 1) A reduction in manpower to the crew required in a conventional shaft sinking operation. 2) A considerable reduction in time to complete a shaft compared to conventional techniques. 3) The use of the V-mole eliminates many of the hazards encountered in conventional sinking. Based on the successful performance of the first three V-moles in Germany, Thyssen Schachtbau decided to employ this principle abroad. In 1980 a second machine of the third generation was built and is now operated by TMCI Construction, Inc. in Alabama. The first shaft was completed at the end of 1981 and this paper describes the method of operation including some unique aspects not attempted on prior V-mole operations and some of the statistics arising out of the experiences during the first shaft boring operation. THE NO. 7 MINE FAN SHAFT SITE Jim Walter Resources, Inc. was formed in 1970 to exploit the coal field in Alabama on the southern tip of the Appalachian coal field. The coal reserves amount to around 650 million tons of mainly good quality coking coal of which about 350 million tons are to be extracted over the next 30 years. Shaft sinking and preparatory work began in 1972, and at present 6 mines are producing around 5.4 million t.p.a. Annual production is to expand to 10 million t.p.a. as soon as possible, and the ventilation shafts to be sunk by TMCI play a vital role towards attaining this goal. The first shaft site is located at the No.7 mine, near Brookwood, Alabama. The actual location of the shaft relative to the production shafts is shown on the mine plan (Fig. 1), which also shows the room-and-pillar extraction system used at present. The mine plan further shows the conveyor route used for the muck removal. The geological survey showed that the strata consisted of horizontal layers of mainly sandstone, sandy shale and shale interspersed with several coal seams. The seam being extracted at the No. 7 mine is a combined seam made up of the Blue Creek and Mary Lee seams at a depth of 513 m (1682 ft) and having an average seam thickness of about 2 m (6 ft). At the beginning of September 1980 the surface site preparation and pre-grouting work was completed by JWR, and TMCI was able to commence with Stage I of the shaft sinking program - the drilling of the pilot hole.

Jan 1, 1982

By A. J. Shaler, H. Udin, J. Wulff

In the study of the sintering of meta powders, we have come to the conclusion in this laboratory that further progress requires a more basic understanding of the operating mechanisms. This is emphasized in detail by Shaler. He has shown that a knowledge of the exact value of the surface tension is imperative for a solution of the kinetics of sintering. This force plays a principal role in causing the density of compacts to increase.2 Furthermore, a knowledge of the surface tension of solids is also applicable to other aspects of physical metallurgy. C. S. Smith3 points out the relation between surface and interfacial tension and their function in determining the microstructure and resulting properties of polycrystal-line and polyphase alloys. This paper describes one group of results of an experimental program designed for the study of the surface tension in solid metals. As a by-product of this work, considerable information has been obtained on the rate and nature of the flow of a metal at temperatures approaching the melting point and under extremely low stresses, a field of mechanical behavior heretofore scarcely touched by metallurgists. The importance of this additional information to students of powder metallurgy need not be stressed. Theoretical Considerations Interfacial tension arises from the condition that an excess of energy exists at the interface between two phases. Gibbs proves that this energy is a partial function of the interfacial area; thus: ?F/?s = ? where ?F/?s is the rate of change of free energy of the system with changing surface area, at constant temperature, pressure and composition, and ? is the interfacial tension, or interfacial free energy per unit area. If one of the phases is the pure liquid or solid, and the other the vapor of the substance, ? may properly be termed "surface tension," and is a characteristic of the solid or liquid. The attempt of a body to lower its free energy by decreasing its surface gives rise to a force in the surface which is numerically equal in terms of unit length to the free energy per unit area of the surface. Thus ? may be expressed either in erg-cm-² or in dyne-cm-1. Similarly, surface tension may be determined either by a thermo-dynamic measurement of the surface energy or by a mechanical measurement of the surface force. We have chosen the latter approach. Tammann and Boehme4 determined the surface tension of gold by measuring the amount of shrinkage or extension of thin weighted foil at various temperatures and interpolating to zero strain. The method is of questionable accuracy because of the tendency of foil to form minute tears when heated under tension. Their assumption of F = 2W?, where W is the width of the foil, is unsound, as the foil can decrease its surface area by transverse as well as by longitudinal shrinkage. Although their experimentation was meticulous, the paper does not include details of the sample configuration required for recalculating ? on a correct basis, even if such a calculation were possible. In the experimental procedure chosen here, a series of small weights of increasing magnitude are suspended from a series of line copper wires of uniform cross-section. This array is brought to a temperature at which creep is appreciable under extremely small stress. If the weight overbalances the contracting force of surface tension, the wire stretches; otherwise, it shrinks. The magnitude of the strain is determined by the amount of unbalance, so a plot of strain vs. load should cross the zero strain axis at w = F?. If balance is visualized as a thermodynamic equilibrium, the critical load is readily calculated. At constant temperature, an infinitesimal change in surface energy should be equal to the work done on or by the weight: ds = wdl [A] For a cylinder, s = 2pr2 + 2prl [2] If the volume remains constant, r = vV/pl [31 s = 2vpl+2V/l [4] ds = vpv/l - 2V/l²) dl [5] Substituting [5] into [I] gives for the equilibrium load, w = ?(z/rV- 2V/12) [6] and, again expressing V in terms of r and l, w = pr?(1 - 2r/l [7] Here the end-effect term, 2r/l, is neglected for thin wires in subsequent work. Eq 7 can be confirmed by means of a stress analysis. If the x-axis is chosen along the wire, then the stress is 2pr? - w pr² pr2 [8] A cylinder of diameter dis equivalent to a sphere of radius r, insofar as radial surface tension effects are concerned.³ Thus xv = 2?/d = ?/r = sz [9] For the case of zero strain in the x direction, the strain will also be zero in the y and z directions. Since the wire is under hydrostatic stress, Eq 8 and 9 are

Jan 1, 1950

By AIME AIME

AMONG the European nations Germany is the center of interest economically as well as politically, and of prime importance for Europe as a whole is Germany's capacity to produce mineral products for armament and for export in exchange for the import of the essential supplies to maintain its industries. So far as minerals are concerned, Germany is worse off than any other great power except Italy, and deficiencies are being met by attempts to increase output from local deposits and by greater use of substitutes derived from domestic raw materials to replace imported metals, petroleum products, and other minerals.

Jan 1, 1939

Jan 1, 1970

By Philip D. Anderson, Ralph Hultgren

Heat contents of extremely pure iron were measured over the range 300"to 1433"K, using a diphenyl ether calorimeter. Results from three samples containing widely differing impurities agreed with one another and with Previously reported results at higher temperatures (1184 ° to 1809°K) by Olette and Ferrier. From these data a table of heat contents of iron has been Prepared which is believed to be more accurate than those previously available. CP values have been derived which are consistent with these heat contents, with the best experimental Cp data, and with the thermodynamic conditions of equilibrium between bcc and fcc iron. The opinion is expressed that low-temperature extrapolations of presently known Cp values for y-Fe are not reliable. It would seem that the thermodynamic properties of iron, which is by far our most important metal, should have been well established long ago. This is not the case, however. As discussed by Olette and Ferrier,' there is objection to every earlier heat content measurement. While the best true Cp determinations agree well at temperatures below the Curie point, there is wide divergence at higher temperatures. Several investigators have examined available data and attempted to calculate thermodynamic functions for iron that are consistent with the two equilibrium temperatures of bcc and fcc iron. The two primary efforts were those of Austin' in 1930 and Darken and smith3 in 1948. The recommended values differ considerably; integration of Austin's Cp values leads to a heat content at 1100°K which is 300 cal per g-atom higher than the value recommended by Darken and Smith. The compilation of Fisher4 in 1949 was based on the selection of Austin. In 1956, Weiss and Tauer obtained yet another set of values by resolving Cp values into components due to dilation, lattice vibration, electronic excitation, and magnetism. The magnitude of contribution by each component and its dependence on temperature was estimated by semiempirical means. Their values are not self-consistent in that they do not form smooth curves when plotted vs temperature; moreover, their calculations cannot easily be repeated since they do not give the values of some of the parameters used. Clearly, experimental values for iron were in a most unsatisfactory state. The presently described measurements of the heat content of iron were therefore undertaken, covering temperatures as high as 1433°K. While the work was in progress, the high-temperature (1193" to 1789"K) heat content measurements of Olette and Ferrier' were published; in the region of temperature overlap the present results agree with Olette and Ferrier well within experimental accuracy. It is believed that the present results, combined with those of Olette and Ferrier, provide for the first time a reliable set of heat contents of iron from room temperature to the melting point. From these data, guided by available Cp measurements, it proved possible to derive Cp, entropy, and free energy function values for @-iron from room temperature to the melting point, and for y- iron in the temperature region of its stability. Exhaustive study led to the conclusion that extrapolations of y-iron functions to room temperature were not reliable enough to be useful; hence these have been omitted from the tables. EXPERIMENTAL Materials. Three samples of extremely high purity iron from different sources, containing widely different impurities, were measured. The first of these, designated "Chipman", was kindly supplied by Dr. K. K. Kelley of the U. S. Bureau of Mines from a lot which was made many years ago by Dr. John Chipman of the Massachusetts Institute of Technology. The second, designated6'Teddington", was supplied by the National Physical Laboratory, Teddington, England, from a lot zone-refined by them. The third sample, designated "Irsid", was supplied by the Institute de Recherches de la

Jan 1, 1962

By William P. Blake

(Canal Zone Meeting, November, 1910.) A DEPOSIT of manganese-ore near Tucson, Ariz., merits notice by reason of the peculiar form in which it occurs, and as a striking. example of ore-deposition by vadose upward capillary flow of metal-bearing solutions with concentration at the surface of the country-rock. This deposit occurs at the northern end of the Coyote mountains, about 40 miles west of Tucson, upon the outcropping beds of porphyritic rock, which appear to be partly-metamorphosed strata of volcanic tufa, probably of late Secondary or of Tertiary age. The strata dip northward at a low angle, and present a series of basset-edges in parallel lines of outcrop, east and west, facing the south and extending over many acres. Successive groups of these outcrops, from 5 to 20 ft. in breadth, are coated with oxides of manganese in lustrous black films and crusts, shining in the sunlight like polished ebony, and covering the whole surface of the rock above the soil. Seen at a little distance, these croppings look like solid ledges of massive and pure ore; but closer inspection and a few blows of the hammer reveal their true nature as a superficial coating allied in origin to the blackened shining surface of rocks exposed in desert-regions, familiarly known as " desert paint" or "desert varnish,"' similar to the phenomena described by me in a former paper, but much thicker and heavier. * By reason of the death of the distinguished author, this communication, probably his last communication to technical literature, is published without revision of the proofs by him. A term first given y G. K. Gilbert. See Rocks, Rock-Weathering, and Soil; by George P. Merrill, p. 256 (New York, 1897). Superficial Blackening and Discoloration of Rocks, Especially in Desert Regions, Trans., xxxv., 371 (1905).

Sep 1, 1910

By Earle Schumacher

THE solidus line above the solid solution field in the lead-antimony system was originally determined by Dean and his associates1 from heating curves. They did not regard this line as having been accurately fixed and in their more recent publications2 the curves drawn do not follow closely the original data. The precise location of the solidus line is of importance in the extrusion of lead-antimony cable sheath, as the temperature of the metal in this process must be less than the lowest temperature at which any part of the alloy in the lead-press charge becomes liquid. It is very desirable, however, to operate at as high a temperature as possible, as the rate of extrusion for a given pressure is approximately doubled for an increase of 10° C. in temperature. The precise location of this line is also important, in the investigation of ternary systems of lead, antimony and a third metal. For these reasons, and because of the differences reported in the literature, data were secured on the lead-antimony solidus line by the classical quenching-test procedure.

Jan 1, 1927