Search Documents

By R. H. Adams, A. M. Khan

The Huntington Beach oil field is on the Pacific Coast, southeast of the City of Los Angeles (Fig. 1). It lies both onshore and offshore. Most of the onshore section is operated by Standard Oil Co. of California, WOI. The Tar reservoir is of upper Pliocene age, about 200 ft thick, and consists principally of fine-grained, unconsolidated, somewhat shaly sand, with thin inter-bedded shale stringers throughout (Fig. 2). The reservoir is a broad, highly faulted, elongated anticline, with an areal extent of about 370 acres. Most of the faults bisecting the structure are normal, trend north-south, and are the main cause of reservoir discontinuity (Figs. 3 and 4). From 1964 to Dec., 1967, 259 steam stimulations were performed on a total of 125 Tar sand wells. Eighty-six new wells were drilled and steam stimulated. Of the total, 96 have been stimulated twice, 34 three times and 3 four times. During this same period, a two-injector steam drive pilot has been in progress. The response obtained from this project has been compared with the response to cyclic stimulation. This paper presents an analysis of the field observations for the two methods of thermal recovery. History of Development Drilling to the Tar pool commenced in 1924 with an initial well production of 40 to 50 B/D of 12o API gravity oil. Complete primary development of the pool has been spread over several years. Approxi- mately 40 wells were drilled during the first phase of development, which was completed in 1945. The subsequent primary development started in 1960 with initial well productions of 30 to 40 B/D oil. Thirty-seven wells were completed in the Tar pool during this phase. For the most part, slotted, gravel flow packed liners have been used in the wells in this pool. A cyclic steam stimulation pilot was initiated in March, 1964. Based on the very successful stimulation in the pilot area, the cyclic stimulation project was expanded to include all of the Tar pool wells producing at the end of 1965 (Fig. 5). Also, a development drilling program was begun at this time. To date, 86 new wells have been drilled under this program. The number of wells drilled each year in this secondary phase of development is also shown in Fig. 5. New Well Completion Practices Most of the new wells have been completed to produce from both the Upper and Lower Tar zones. Generally, a casing stub is cemented from the top of Lower Tar to the base of clean Upper Tar sands to exclude intermediate water-bearing sands. The water string is then cemented from the top of Upper Tar to about 1,500 ft with neat cement and 30 percent silica flour. The annulus from 1,500 ft to surface is then filled with a petroleum-based gel through a high-temperature port collar. Once again, a history of sand-free production dictated the use of 60-mesh gravel flow packed liners. The Upper and Lower Tar

Jan 1, 1970

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By K. E. Robinson

This study is the extension of an investigation of reclamation of floodplain areas in the Coeur d'Alene Mining District, Idaho, that are unuseable in their natural condition, by construction of landfills with mill tailings. The study develops a valley-wide tailings disposal plan to utilize 20 potential landfill sites on floodplain areas and presents measures for reclaiming the sites for subsequent productive use. Field and laboratory testing on a test section and two abandoned impoundments support the use of hydraulically deposited tailings for landfill construction. Hydrological testing has shown that controlled discharge from tailings impoundments results in contaminant levels in the discharge below regulated standards. Additional testing indicated that compacted soil liners and pond management provide adequate contaminant abatement where acid-generating tailings are encountered. Mechanical compaction, including surcharge loading, upgrades foundation support capacity so that construction on the surface of tailings deposits is feasible. On completion of the testing program, the test sections were abandoned and rehabilitated. Details concerning potential landfill sites have been refined. At recent production rates, the 20 sites would result in 680 acres of reclaimed land, while providing a minimum of 40 years of tailings storage capacity. A general design has been developed for the retention dikes. Aspects of embankment stability, including liquefaction are discussed, and are shown to provide an adequate factor of safety under the anticipated range of operating conditions.

Jan 1, 1983

By Hani Henein, J. Barry Wiskel

"The easy accessibility and power of the PC, as well as the education of our engineering students in the use of these tools, are compelling reasons for developing computer aided instructional (CAI) tools. There are a wide range of areas in the engineering curriculum where students must learn the steps and the process of applying judgement in problem solving. In the typical course instruction, · an instructor introduces theory to students; the application of the theory to solving problems is often demonstrated in the abstract. Students therefore spend a significant amount of time learning how to apply the theory to problem solving. Additional time and effort must then be spent to get students to the point of learning concepts and integrating this knowledge. A number of computer aided packages have therefore been developed for use in several courses in the materials science and engineering curriculum that encompass both calculational and instructional capabilities. This paper presents an overview of some of these packages which include the solution of a non-linear equation, the instruction of binary diffusion couples, an introduction of crystallography, an introduction to heat transfer and the solution of thermodynamic stability diagrams. The context in which these CAI Tutorials were developed and are being used will be discussed. The pitfalls in the development of these packages will also be discussed. The use of the tutorials has important implications on the expectations from an engineering education of both instructor and student.IntroductionTraditionally, it is quite routine to teach engineering students how to use a computer (the PC today for undergraduates) as a tool in performing engineering calculations or in simulating a process or a unit operation. This often takes the form of one course in computer programming, whether it is Fortran, Visual basic or a spreadsheet, and another course in numerical computation. However, the materials and electronic revolution have brought about considerable advances in computer power and speed, and accessibility. Today, the manipulation of digital images, movies, and speech are commonplace on a desktop PC.' Many mathematical models that were executed only on workstations can now be readily handled on a PC. Concurrently, more of our students own a PC even if their curriculum does not require them to purchase one. Today, virtually every university student has been introduced to the PC in either their elementary or high school education. Hence, the increased capabilities and accessibility of the PC and the familiarity of students with this tool make it compelling to explore its use as an educational tool for our engineering students. This is not a traditional role of a computer in our engineering curriculum."

Jan 1, 2000

By U. Sachse

This paper explores a systematic approach for mining decision-makers to use when faced with choosing which method to use for a specific rockpass length. The different excavation methods available in the broad South African mining industry are compared against a number of critical parameters, as applied to rockpasses of varying length. This approach is not meant as a definitive, prescriptive planning tool, but rather as a proposed approach to enable designers and planners to choose the best system to excavate their specific rockpasses

Jan 1, 2005

By John C. Edwards

A computer program, developed for the Bureau of Mines under contract, predicts in a quasi-steady-state approximation the ventilation and contaminant concentrations and temperatures when a fire occurs in a multi-level mine. For periods of time in which there is no significant change in the ventilation, yet a fire is producing fumes, a real-time fume concentration throughout the mine is calculated. Multiple and time-variable contaminant sources can be simulated. Recirculation paths that can develop provide a mechanism for increasing the fume concentration in the mine network and are identified by the computer program. This report contains a listing of the Fortran computer program as well as the required format of the input data. Two examples are provided of the real-time spread of smoke from a fuel-rich fire throughout a multilevel mine. The first example considers an operational exhaust fan as well as a booster fan. The second example evaluates the real-time smoke spread following a failure in the exhaust fan; recirculation occurs in this latter case.

Jan 1, 1982

By A. N. Holden, W. E. Seymour

DURING the last several years, the U-Zr system has been studied at many laboratories as one of the research programs sponsored by the Atomic Energy Commission. The equilibria in part of this system have been difficult to determine, although the phase diagram from 0 to 60 atomic pct Zr has been established with reasonable certainty. Existing diagrams of the system vary appreciably beyond 60 atomic pct Zr, particularly with regard to the existence of an intermediate phase. Most existing diagrams show a transformation or reaction horizontal near 600°C. In 1955, a collection of uranium phase diagrams' was prepared at the Battelle Memorial Institute and the U-Zr diagram in that collection contained a questionable region in the vicinity of 60 to 80 atomic pct Zr. Summer-Smith" has published a phase diagram of the system that shows no intermediate phase. Summer-Smith did his work with powders and found only the uranium and zirconium eutectoid mixture from X-ray patterns of material annealed below 600°C. Mueller3 at Argonne National Laboratory did similar work with filings, and he found that initially there was a pattern of an intermediate phase, but on long-time annealing

Jan 1, 1957

Jan 1, 1925

By F. D. Forgeron

"ONE OF THE FIRST DOCUMENTED APPLICATIONS of soil geochemistry in the Canadian Shield was that carried out by Chisholm in the Kenora district in 1949. This survey proved successful in outlining sulphide-associated gold veins utilizing cold-extractable metals. Since then, mining companies, government agencies - both provincial and federal - and universities have conducted soil investigations. Some of the results are documented in publications, others are on open file in provincial and federal mines departments and, unfortunately, many other investigations with both successful and unsuccessful results are buried in company files or have been discarded. This paper deals with soils within the scope of chemical studies of overburden in the Canadian Shield. The subject is a broad one and some definition is required. The soil investigations discussed herein are those aimed at the testing of specific targets more or less in the source area. This definition distinguishes soil investigations from other overburden studies which commonly monitor metal accumulations at some substantial distance from the metal source. Naturally this distinction is relative, because in many instances there is overlap."

Jan 1, 1971

By W. K. Overbey

The Bureau of Mines conducted surface joint and stress measurements, airborne remote sensing imagery studies, compass-oriented borehole televiewer surveys, numerical simulation of fractured wells, and well productivity studies in a four-quadrangle study area of Ohio, to determine the effects of earth fracture systems on the deliverability of gas storage fields. The results of these studies indicate that much useful information about a gas storage reservoir can be obtained and put to practical use by studying--(1) oriented cores for fractures and directional permeability, (2) orientation of induced hydraulic fractures for alignment of well patterns, and (3) aerial photos and multispectral scanner imagery for general surface geology comparison and to determine if some, development patterns can be generated by such results. The absence of known tectonic elements associated with flat-lying sediments, such as faults or fracture zones that can be seen on the surface, indicates that the use of remote sensors such as radar or aerial photography is not likely to be useful in picking well locations for drilling. Studies similar to those discussed here should be conducted in gently folded and strongly folded sedimentary formation areas to determine if the increased knowledge of earth fracture systems under these conditions might be beneficial in gasfield and gas storage reservoir development.

Jan 1, 1974

By Clyde L. Holmberg, Paul Zinner

"INTRODUCTION In view of the large tonnage of low-grade iron ore and iron-bearing material known to exist at the western limits of the Gogebic range, the Bureau of Mines undertook an investigation of the area for the purpose of evaluating the iron-bearing formations as sources of iron for possible future utilization.After 6o years of exploration an, development on the Gogebic range, the area investigated by the Bureau represents the known western limit of direct-shipping ore mined from operations on the Gogebic range.An area about 2 miles in length between the villages of Pence and Iron Bolt in Iron County, Vic., was selected for investigation, and trenches wore excavated through the overburden and fully across the iron-bearing formation to obtain 108 bulk samples for beneficiation tests. Exhaustive tests involving gravity and flotation methods, magnetic separation, and magnetizing roasts followed by magnetic separation were conducted on the samples to determine the ammability of the individual formations and the entire iron-bearing zone to beneficiation.Empirical data on the character and mineral content of the formations arc tabulated herein, as well as the results of the beneficiation tests."

Dec 1, 1947

By G. R. Addie

"In February, 1975, the President of Georgia Iron Works Company, Mr. Tom Hagler decided to build a new hydraulic laboratory to water performance test all of the companies' centrifugal slurry pumps.Equipment procurement started in March, 1975, by ordering of a mini computer data acquisition system.Work commenced on the lab in July, 1976, by erection of a Butler Building and the laying down of a 20,000 gallon concrete sump.By late October, a facility compromising two water test loops of 8"" and 18"" pipe diameter was in operation carrying out head quantity and suction performance tests on pumps up to 16"" in size.In August of the following year, an 8"" diameter pipe slurry loop was installed to enable pipe friction and deposition velocity of a slurry to be measured in an 8"" inside diameter pipe.With the encouragement of Reserve Mining in Minnesota and IMCC in Florida, this was followed in March, 1978, by the addition of over 300 feet of 18"" diameter pipe to make up an 18"" diameter pipe slurry system complete with head loss and deposition velocity observation sections.The office and shop areas of the lab were again expanded in April, 1978, to provide further expansion to the test sections and staff facilities."

Jan 1, 1980

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

By Anthony D. Barley

Over 60,000 multiple anchors have been used internationally since their introduction in the early 1990s, including 1000 in the United States. The multiple anchor system comprises a "multiple" of "unit" anchors installed within a single borehole - each unit anchor being staggered within the borehole length to mobilize its own capacity independently of the other unit anchors. These systems offer higher capacity than conventional anchors with identical bond lengths due to superior load transfer efficiency. The use of higher capacity anchors may allow reduction in the number of anchors required on a project, which results in time and cost benefits to the anchor installer, contractor, and the owner. Fully removable temporary multiple anchors are available, and have been used with consistent success. Three case histories are discussed highlighting the use of these systems

Jan 1, 2002

By I. L. Whyte

apparent density and drag coefficient of porous ores on

Apr 1, 1995

By R. G. Garrett, A. J. S. Geddes

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The 1986 geochemical survey was successful in recognising all the previously known mineral occurrences of significance in Jamaica, in outlining areas not previously believed to have mineral potential and in stimulating fresh appraisals of old occurrences in terms of their potential for new commodities. This has resulted in a very significant increase in mineral exploration activity in Jamaica

Jul 1, 1991

By E. B. Nelson, B. W. Gandrud, B. M. Bird

"The Lewisburg No. 2 mine of the Sloss-Sheffield Steel & Iron Company is located in Jefferson County, Alabama, about 7 miles due north of Birmingham. At this point the coal from the Mary Lee seam when coked in by-product ovens yields an excellent quality of metallurgical coke suitable for use in the iron blast furnace; it is also an excellent steam coal. In mining, all three benches are worked. Coarse impurities are largely gobbed by the miners underground.In addition to giving the data obtained from screen-sizing and float-and-sink tests of a representative sample of the raw coal, this report presents the results of slotted-screen tests to show the proportions of flaky particles in selected sizes, and the results of tests to show how much coal is liberated from impurities by crushing the coarsest sizes. These data have been obtained in connection with an extensive study of coal-washing now being conducted by the U. S. Bureau of Mines and the University of Alabama, with U. cooperation of the different operators of Alabama. As the work progresses other reports will follow containing furtner data on the washability both of the Mary Lee seam and of other seams in Alabama and giving the results obtained in preparing these coals by various methods.Although a great amount of investigative work on the preparation of the Mary Lee scam was previously carried on by the various coal companies of the district, comparatively little of this information has been published. In governmental publications three references have been found. Forbes5 gives a number of sections with proximate and ultimate analyses of face samples taken in the mines. Gandrud and Britton'' show sections of this seam at Flat Creek and New Castle; they also give the specific gravity and ash contents of the partings of coal and impurities. In their paper Yancey and Fraser7 include washability studies and washing data from the Sayreton mine of the Republic Iron & Steel Co."

Jun 1, 1930

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By Marcello Crispi, Valdir Silva, Juarez Moraes

Companhia Vale do Rio Dote - CVRD is the largest mining company in Brazil and the largest iron ore producer in the world. Serra Geral Mine (SGM) is located at Iron Quadrangle of the State of Minas Gerais, approximately 80 kilometers from Belo Horizonte. Hematite and Itabirite are the two main minerals. A blasting with a spherical charge has been introduced at Serra Geral Mine, an iron ore producer in Brazil, belongs to the CVRD (51%) Kawasaki Steel Corporation (24.5%) others (24.5%), in order to improve fragmentation, as well, load, transportation and crushing productivity. This paper will present the results of a successful blast design with a spherical charge carried out by Serra Geral Mine, the Department of Mining Engineering at Escola de Minas - Federal University of Ouro Preto-UFOP associated to a Blasting Engineering Consultant. The results obtained in the field tests and how it was possible to increase the blast pattern in 53%, which allowed one reduction around 31% in the cost of blasting operation in the Serra Geral Mine, will be discussed in details.

Jan 1, 2002

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004