Search Documents

Precast prestressed concrete piles designed to be end-bearing in a sand stratum at Drax Power Station met with extremely variable resistance during driving. Some piles came to virtual refusal almost immediately on entering the sand whereas others were driven to considerable penetration with very low resistance. Redriving and load tests on piles experiencing low resistance on initial drive showed that take up in strength occurred over a relatively short period of time. Investigations involving the use of pneumatic piezometers revealed the development of significant excess pore pressures during driving. Samples from boreholes showed that piles met the least resistance when the sand had a high silt content. Comparison with the original site investigation data demonstrated the difficulties in predicting detailed pile behaviour. The varied behaviour could not be related to the original borehole logs or to SPT or static cone penetrometer results. The factors controlling pile driving behaviour were essentially geological and could only be explained with reference to local soil grading.

Jan 1, 1989

By Dean Lindsay, Inna Dymov, Mariam Melashvili, Jim Smolik, Chris Fleming

"This paper presents results from the proposed cyanide detoxification circuit for Seabridge Gold’s KSM project. The proposed flowsheet uses a two-stage CCD (counter-current washing/decantation) circuit to transfer the flotation products CIL(carbon-in-leach) barren solution to a SART process (Sulphidization, Acidification, Recycling of precipitate, and Thickening of precipitate) to recover copper and free cyanide from the copper cyanide complex. The SART barren solution is then treated by an AVR process (Acidification, Volatilization of HCN gas, and Reneutralization) to concentrate the cyanide that was liberated in SART for recycling to leach. The washed CIL barren pulp (the CCD underflow) is treated with the SO2 /Air process to oxidize residual cyanide.The goal of this complex flowsheet is to recover and recycle as much cyanide as possible and produce a final effluent containing less than 0.5 mg/L copper and CNWAD at the lowest cost. The SO2/air process is capable of achieving low residual CNWAD (<1 mg/L) in the final product, but the persistence of aqueous copper above the target level has been detected in the treated solution in some instances. The expected high concentrations of copper and cyanide in the KSM CIL barren ( >200 mg/L each species) and the difficulties this might create for the SO2 /air process was a key factor in the decision to consider including the washing, SART and AVR steps in the project flowsheet.The target concentrations of CNWAD and Cu were readily achieved after aging the SO2 /air treated pulp, as would occur in a tailing or polishing pond. This suggests no additional treatment will be required to sustain low levels of these species in the final plant effluent."

Jan 1, 2015

Real gross national product increased at a larger-than- expected annual rate of 8.3 percent in the first quarter of 1984, with both consumption and investment spending increasing significantly in real terms (table 1). Residential and nonresidential fixed investment increased at annual rates of 25.7 and 14.6 percent during the first quarter of 1984, and investment in nonresidential structures, which declined in 1983, also increased during the first quarter of 1984, nearly attaining its 1982 level. The annual level of personal savings increased $27.7 billion, while the personal savings rate (the ratio of personal savings to disposable income) increased to 5.8 percent during the first quarter. The increase in the personal savings rate comes as welcome news to analysts concerned over the flow of loanable funds to the private sector and the impact on interest rates in 1984 of increased private and Government demands. U.S. Minerals Industry Performance A major upswing in the performance of the metal mining sector occurred during the first quarter of 1984, with production increasing almost 11.2 percent from January to March, The recovery of the metal sector is also reflected in the performance of primary metal industry profits, which were positive during fourth quarter 1983 following seven consecutive quarterly losses (table 1). Two thousand nine hundred more metal mining production workers were employed in February 1984 than in February 1983.

Jan 1, 1984

Techniques Used and Problems Encountered in Normal and Reverse Circulation Drilling at the Mt Roseby Project, Cloncurry, North West Queensland

Sep 13, 2010

By Charles E. McCarthy, MORTON T. PAWEL, E. A. GEE, FRANK S. RIORDAN

Large tonnages of the magnesium silicate mineral , olivine, are known to exist in the mountains of western North Carolina and in the Puget Sound region of Washington. The North Carolina deposits alone are reputed to contain at least 230 million tons of ore averaging 45 to 49 percent of magnesium oxide In both areas the mineral is readily accessible and can be mined by the simplest methods ; one of the largest of the Washington deposits is located at tidewater .

Sep 1, 1946

By S. C. Richardson

The electrowinning (EW) circuit involves using DC current in the electro-deposition of metal ions dissolved in an electrolyte solution. This paper reviews a method to generate an electrical model of an EW circuit and the resulting DC current flow and voltage distribution within the circuit. Topics include: calculations of electrolyte conductivity and the equivalent electrical resistance of the electrolyte within the electrolyte pipelines connected to the EW circuit; the breakdown and classification of the EW cell voltage into thermodynamic and ohmic potentials; methods to calculate current flow and voltage distribution throughout the EW circuit; and the development of an interactive visual computer model to simulate an actual EW circuit. Stray current can pose an electrical shock hazard to employees in electrolytic tankhouses. Increased awareness and understanding of the voltage distribution and potential stray current in an EW circuit can help mitigate the risk of tankhouse workers becoming exposed to electrical shock hazards. INTRODUCTION Copper electrowinning tankhouses include rectifiers that deliver large amount of DC current to a series of electrolytic cells consisting of electrolyte solution and electrode pairs. The design also includes metallic conductors in the circuit which include the rectifier’s positive and negative busbar, inter-cell busbar, and the anode and cathode frames. The electrolyte acts as an electrical conductor that transfers current via ions between the anodic and cathodic electrodes within the cell. Electrolyte, as a conductor, is also capable of conducting DC current outside the main EW circuit through the connected electrolyte feed and return pipe systems. DC current that follows a path other than the intended path through the series of electrolytic cells is referred to as “stray current”. Developing an electrical model enhances understanding of voltage distribution and current flow in an EW circuit. This paper discusses the derivation of the various representative components of the model as well as the output from the model. An interactive visual computer simulation incorporates the model output in order to aid in the understanding of voltage distribution and current flow throughout the EW circuit.

Jan 1, 2019

By L. Q. Luo

SHP-F3200 wet high-intensity magnetic separator (HIMS) was successfully used to separate the complex and weakly magnetic iron ores being composed of specularite, limonite and siderite in Ji-uquan Iron and Steel (Group) Co Ltd (JISCO). It is more and more difficult to separate iron ores from gangues, such as quartz, jasperite and phyllite, as the properties of iron ores gradually become more complicated and refractory. Some technologies have been used to improve SHP-F3200 HIMS, including modifying angle of magnetic polar from 90°to 83°, cooling exciting coils by oil instead of air, adding reverse-washing device to wash off magnetic particles, adjusting the tooth-space of matrix from 5.0 mm to 3.5 mm or 2.5 mm, so as to enhance the recovery of fine iron ore particles. It is still difficult to meet the requirement for recovering more difficultly-separated iron and the demands for high-grade concentrate of iron. In this paper, after analyzing magnetic force exerting on iron ore particles within different separating sections of SHP HIMS, it is proposed to apply the flowing-film technique into the HIMS. Thus a new-type LY matrix is designed to form magnetic gradient vertically, combined with a special flowing-film feeder to improve the existing SHP HIMS. The moving pattern of magnetic particles in pulp in HIMS separation district also has been analyzed in this paper. And the test on the SHP-F700 HIMS shows, under the condition of iron ore containing 30.52% Fe, with particle size of ?0.074 mm accounting for around 75%, if applied with flow-film technique, the iron recovery will be up from 69.45% to 76.07%, by 6.62 percent, with the same grade of concentrates of iron. The calculation of iron yield of every size fraction and the tests showed that film magnetic separation (Film-MS) could promote the iron yield of each size fraction, denoting an excellent result of application of the film technique to SHP HIMS. The mechanism of the film magnetic separation technique is to convert the turbulent flow and disordered movement of dynamic mass particles in the pulp into a directional and ordered laminar flow along the surface of tooth plate so as to strengthen the separation effects.

Jan 1, 2014

By BUREAU OF MINES

This report is submitted in accordance with the provisions of the Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1953 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: R. I. 5043, Part I - 011 From Coal. R. I. 5044, Part II 011 From 011 Shale. - Identical in each report, the introduction summarizes research progress made in 1953 under the entire Synthetic Liquid Fuels program. A free copy of each of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Apr 1, 1954

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

By Luke Erickson

San Francisco Public Utilities Commission is planning to replace 5 miles of pipeline under San Francisco Bay. The tunnel will be constructed using an Earth Pressure Balance (EPB) TBM and will be the first TBM-driven tunnel under the Bay. The alignment passes under environmentally sensitive habitats, through interbedded layers of sands and clays, and through a buried bedrock ridge. This paper discusses the geotechnical characterization and anticipated tunneling conditions and presents the analysis of various construction methods that resulted in the selection of an EPB TBM. Considerations related to tunneling with an EPB TBM are described in detail, including ground conditioners, TBM cutterhead wear, muck control, and squeezing ground.

Jan 1, 2008

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

By John Lemke

Current practice for monitoring static pile load tests commonly consists of measuring load and displacement at the top of a pile. This is typically accomplished by monitoring dial gauge movements, line pressure of a hydraulic jacking system, and electronic load cells on occasion. While this testing approach provides useful information for one boundary condition (the top of the pile), a system that measures movement and/or strain along the entire length of the pile can provide additional useful data that can be used to refine pile design. Automated data acquisition systems provide the essential ingredient that can integrate these types of sophisticated instrumentation devices into a standard pile load test program in a cost effective way. This paper provides a general overview of pile testing instrumentation and describes a newly developed chain of instrumentation modules that can be embedded in a pile to gather additional testing information. The new system can measure forces and movements within the test pile synchronously with measurements at the pile top, and the direct application of this system to axial and lateral pile testing is illustrated. This is particularly relevant to the design of ACIP and drilled displacement piles since determination of the reinforcement cage length is important from the standpoint of both seismic design and foundation cost.

Jan 1, 2002

The use of a time series variogram as an aid in controlling the quality of a product was pioneered by Pierre M. Gy and is described. The ability to analyse and interpret covariance relationships time series data is possible using the variogram. The concept of stream heterogeneity allows sources of variability in process streams to be identified and isolated. Principally this is distributional heterogeneity that is due to a short range effect of segregation in the process stream related to size or composition distribution of the material on a local scale and due to a long-range change in the size and grade of the material stream. The variogram is simply a tool for representing these sources of variability in a way that is explicit, allowing identification of the source and providing important insights to temporal continuity between samples. This paper describes the chronologically related large-scale variability in an iron ore process stream (%Fe), and illustrates the control and mitigation of variability at various stages within the process using a variogram. Three main sources of variability are identified including the random variability V[0], the process variability V[1], and the variability due to cyclical phenomena V[cyclic], arising from human routine or mechanical defects. These sources of variability can be represented on the control chart that provides the plant superintendent with insights as to the sampling capability of the systems in place. Maintaining levels of variability within customer specification limits requires that production systems be controlled without overcorrecting for the trends in changing quality. This can be done only by representing the limits of control relative to the limits of specification on a control chart. Where the specification limits encroach on the control limits, one or the other, or both, may need to be changed; specification limits that constrain the control limits lead to reactive decision making that is expensive and stressful for plant operators.

Jan 1, 2008

By Malcolm Powell

"The argument has long raged across the oceans as to what the best AG/SAG mill aspect ratio is. The North American practice of a high aspect ratio of two, diameter twice length, through to the South African and Scandinavian practice of an aspect ratio of as low as a 0.5. Within the collaborative P9 AMIRA project the MPRU of the University of Cape Town and the JKMRC of the University of Queensland have been collecting plant data pertinent to this issue over the past four years.The JK SAG mill model developed by the JKMRC is based upon data collected from mills having a range of aspect ratios from 1 up to 2. The maximum mill speed, mill load, and ball filling in the fitted data base were all below the operating range common in South Afr-ica. The extension of the P9 project into South Africa therefore lent an ideal opportunity to collect data in a whole new window of operation that would allow the range of applicability of the semi-empirical SAG model to be greatly extended.At the heart of the differences in aspect ratio is the completely different operating practice for high- and low- aspect mills. The mill filling, mill speed, and recirculating loads of closed-circuit single-stage operation have more influence on the differences in operation than the pure aspect ratio relationship. Relationships for load have been extended to 45% filling, with the modified model showing the measured peak in throughput as the mill filling increases. The ball load relationship now covers fillings of over 30% balls (of total mill volume), thus including so-called SAG-ball mills. The influence of closed circuit operation has been measured. It has been found that a key issue of the high slurry flows associated with closed circuit operation, especially when closed with a cyclone, is the pulp discharge limitation of the traditional grate and radial lifter configuration. It has also been observed that absolute mill length is more of an issue than aspect ratio. Slurry flow along the mill and charge segregation within the load are being investigated on pilot and full-scale mills to provide data for potentially modifylng the perfect mixing model that is used for the SAG mill.Improved understanding of these aspects of SAG mill operation and extension of the JK SAG model to better cover the entire range is allowing serious direct comparison of high- and low aspect mills for the first time. It is the conclusion of the researchers working in this area that there is no one best practice, that in fact mills across the range have their application based on ore type, desired product, available capital and on operating costs. Developing robust designs allows direct comparison of two-stage circuits using high-aspect primary SAG mills, with single-stage closed circuit low-aspect SAG mills. The new operations within South Africa are now considering both circuit types, and data is presented on selections that cover the full range of aspect ratio and operating practice."

Jan 1, 2002

By Chelsea Woodward

The Spokane Research Laboratory of the National Institute for Occupational Safety and Health has demonstrated a prototype hydrogen-fueled mining vehicle as an alternative to diesel equipment in underground mines. Safety and control systems were added to allow a 70-kW rubber-tired hydrogen vehicle, originally developed by the U. S. Bureau of Mines and Hydrogen Consultants, Inc. (now Hydrogen Components, Inc., of Littleton, CO), to be tested. This work began in late 2000 and culminated with a Mine Safety and Health Administration fire safety review and field tests at the Stillwater Mine in Nye, MT, in 2004.

Jan 1, 2006

By M. C. Irani

This study is a survey of supply and demand for minerals, metals, alloys, and compounds used by the chemical industries in the Ohio River Basin (ORB) area of Ohio, Pennsylvania, and West Virginia during 1967. Data for the study were obtained from completed questionnaires received from chemical manufacturers and from interviews with officials of chemical companies and mineral producers and distributors. The information includes kind, quality, quantity, values, sources, specifications, uses, and methods of transportation. Results of the study show that of the total value of mineral materials consumed by the chemical industry, manufacture of inorganic chemicals consumed 46 percent; fertilizers, 22 percent; and soaps and detergents, 19 percent. Fifteen commodities accounted for 91 percent of the total value of mineral materials consumed. Five of these--phosphates, potash, salt, sulfur, and titanium dioxide--accounted for 59 percent of the total.

Jan 1, 1970

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By S. E. Pérez-Fontes

An experimental study on the oxidation of chalcopyrite (CuFeS2), pyrite (FeS2), covellite (CuS) and chalcocite (Cu2S) particles was conducted by means of differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) techniques. The oxygen concentration in the process gas was set to 40% and 70% (by volume) and a heating rate of 40°C/min was used. Response variables included the temperature of incipient reaction, the total exothermic heat of reaction, particle mass, morphology and mineralogy of the reacted particles. Based on the experimental data and phase stability calculations, reaction mechanisms were proposed to represent the behavior of the particles during oxidation. The reaction mechanisms were verified by X-ray diffraction (XRD) analyses of the oxidized particles and by thermochemical and mass balance calculations to reproduce the DSC and TGA data. Overall kinetic models were developed to represent the evolution of the exothermic heat of reaction as a function of time.

Jan 1, 2007