Search Documents

By Job Goostray

IN THIS paper, as in so many other discussions of historical nature, there is little chance for original material and much has had to be rewritten from older papers, documents, accounts, reports, and the like, some of which are of doubtful authorship or contain conflicting statistics. Fully aware of these little historical pitfalls, the authors have tried to quote the origin where possible, and also to seek further confirmation when the statement warranted it, but cannot assume responsibility for certain facts and dates. The Encyclopedia Britannica was frequently consulted. The authors wish to acknowledge assistance from MacKintosh-Hemphill Co.-formerly the Fort Pitt Works-and also from officials of the Watertown Arsenal who loaned valuable books and gave much necessary information. They are particularly indebted to Colonel Dixon of that institution. The data on modern guns were furnished by Mr. F. Brauer of the Watertown Arsenal; Mr. H. S. Chaffee assisted by obtaining records and data of work carried on by the Builders' Iron Foundry of Providence, R. I.

Jan 3, 1925

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and the introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-techno-logical cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

In 1962, minerals beneficiation showed definite signs of coming out of the doldrums into which it has drifted after the uranium boom. Demand by steelmakers for high-grade iron pellets has created the need for concentrating plants to upgrade specular hematite by spiral concentration or flotation and magnetites by magnetic means and flotation. According to a paper given at the AMC annual meeting by C. S. Arms of Pickands Mather, "the shipment of pellets, started in the mid-1950's, has increased to 17.6 million tons in 1961 from North American operations. Many plants already underway will raise this production to about 42 million tons by 1965. This will be a very sizeable percentage of the total iron ore production contemplated by that date." Iron ore concentration methods are gradually raising the assay of pellets into the 65 to 69% Fe range and lowering silica to the 4 to 7% range. Quebec Cartier's Lac Jeannine concentrator went into operation in late 1961 and all grinding units were running by 1962. The Iron Ore Co. of Canada's new Carol Lake plant was started in mid-1962.

Jan 2, 1963

By S. H. Ash

For several years considerable activity has been devoted to economic and social factors affecting California metal-mining operations as they relate to accidents and their cost. The reason for this intense interest is that accidents cost this industry annually over $1100,000 in industrial insurance premiums for mines insured by insurance carriers only; during 1924-32, inclusive, they amounted to $3,616,9115. There are several reasons for this high cost, the most important of w rich are the consistently .high frequency and severity rates of injuries occurring in the industry. Coordination of effort, appreciation of a mutual problem, and widespread education are essential if accidents and their cost are to be reduced.

Jan 1, 1935

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

By Paul M. Price

The Mouat mine, Nye, Mont., was reopened in 1953 by the American Chrome Co. under a Defense Minerals Production Administration contract. Operations were terminated in 1961 after completion of the contract. Mining methods employed during this period are described in detail, and cost data are presented by years for 1953 through 1959. Ultramafic rocks of the Stillwater complex in Montana contain the largest domestic resource of chromite, and the Mouat mine has been the largest producer. Mine reserves were estimated in 1960 to be about 4.4 million tons containing 22.5 percent Cr203. The chromite deposits occur as a series of overlapping bands or lenses roughly paralleling the steeply dipping layers of the complex. Only two of the chromite layers have proven to be of economic importance. One layer is 2 to 1.6 feet wide; the other is 3 to 8 feet wide. Shrinkage stoping was generally used throughout the mine, but various methods of ore breaking, scope drawing, chute construction, etc., were tested to improve output and lower costs. Long-hole stoping proved to have limited use. Breasting down benches, developed outward from the center of the stope with air-leg drills, was satisfactory only in wider scopes. At the close of operations, the company had standardized the use of lightweight stopers to advance a flat back by breaking from a centrally located face. Mining costs were reduced 47 percent during 7 years of operation.

Jan 1, 1963

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

IN 1906, soon after his arrival in New Zealand, a brief article was prepared by the writer on "The Salient Features of the Economic Geology of New Zealand," for the Journal of Economic Geology. In November, 1907, a somewhat similar paper, entitled "The Mineral Wealth of New Zealand," was read at the Royal Colonial Institute in London. The present contribution to the Transactions...

Jan 1, 1909

By S. K. Mitterecker, T. Hofbauer, F. Baerhold

"Acid regeneration is a very important process step in each acid leach circuit. It is required to recover dissolved metals and HCl from spent leaching acid. Andritz Metals presents its recently commissioned spray roast pilot plant. The facility is now available for testing and demonstrating acid recovery or metal oxide production which is a requirement in several flow sheets under development for the mining and specialized oxides industries. Results from pilot test campaigns are reported here. We are currently focusing on a nickel ore leaching process, which requires both a feasible iron control and acid regeneration step. In addition, we disclose the results of a magnesium ore and aluminium recycling test campaign conducted in our pilot plant facility.INTRODUCTION Hydrochloric acid regeneration is widely used in the steel industry to regenerate spent pickle liquors into hydrochloric acid at a typical concentration of 18 wt.%. Andritz Metals (formerly known as Ruthner) has built more than 200 acid regeneration plants worldwide (Andritz Metals brochure). As technology leaders Andritz also has vast experience with specialty metal oxide plants, producing metal oxides such as aluminium oxide (Al2O3), magnesium oxide (MgO), nickel oxide (NiO), cobalt oxide (Co3O4) and mixed oxides from metal chloride solutions (Baerhold F., Lebl A., Starcevic J., 2006), (Jedlicka, H., n.d.), (Ruthner M.J., Krischner H., 1973), (Ruthner Ind. Planungs AG, 1967). Hydrochloric acid leach circuits have been developed and proven in the industry for many years. Examples of industrial applications are: synthetic rutile production (TiO2) (Walpole E.A., Winter J.D., 2002), Quebec Iron and Titanium’s UGS process (Patoine M.-C., De Mori A., Borowiec K., Coscia C., 2002), magnesium and potassium production (Priemer H., 1973) and Goro Nickel (Vahed A., Colton D.F., Duterque J.P., Karner W., Baerhold F., 2004), (Taylor A., 2013). One of the critical process steps in developing a hydrometallurgical process is acid regeneration, as it is an economic requirement to recover both the dissolved metals and acid (commonly HCl) from the spent leaching solution."

Jan 1, 2016

By W. F. Watts

In 1980 the Bureau of Mines developed the Mine Inspection Data Analysis System (MIDAS). MIDAS is a computerized, industrial hygiene data base capable of statistically analyzing environmental data collected in coal and noncoal mines and mills by Mine Safety and Health Administration (MSHA) inspectors or mine operators. The objectives of this report are to describe the current contents of MIDAS, to report analyses of coal and noncoal mine respirable dust samples collected by MSHA inspectors and to evaluate the proposed change in the metal and nonmetal respirable dust standard from a formula based upon the percentage of quartz identified in the sample to 100 µg/m3 of respirable quartz. Based on samples collected by MSHA inspectors, changing the noncoal respirable dust standard would result in 4 pct fewer samples with dust concentrations exceeding the standard. Analysis of respirable coal dust data collected by MSHA inspectors showed that mines with longwall plows or shears had the highest geometric mean concentrations (1.64 and 1.29 mg/m3, respectively). Mine operations using continuous rippers out-numbered longwall mine operations about 10 to 1 and had a geometric mean concentration of 0.66 mg/m3.

Jan 1, 1987

By Howard A. Perko, M. Mae Benvenga, Heather H. Trantham

Displacement of soil and groundwater during helical pile installation can produce excess pore water pressures (PWP) in fine-grained soils. Pore water pressure reduces effective stress in the soil immediately adjacent to the helical pile shaft and near the helical piles. Previous studies have shown generation of PWP may affect the capacity to torque ratios of the helical bearing elements. Large diameter helical piles that generate much of their torque and capacity from shaft adhesion are affected by PWP and therefore exhibit significant pile "freeze" after installation. Computer modeling is used herein to evaluate PWP immediately adjacent to helical pile shafts during installation in various soil types. The models show the degree and distance from the shaft that is influenced by PWP during installation and the amount of time required for the PWP to dissipate. Pile freeze has been measured on several project sites by re‐torque measurements. These re-torque data are compared with computer modeling and correlations between saturated hydraulic conductivity and dissipation time are presented and discussed. INTRODUCTION Helical piles are full-displacement piles, meaning installation does not produce drill spoil. Soil is displaced laterally as the pile progresses into the ground. This displacement of soil causes an increase in PWP, which reduces adhesion between the pile and the soil. For helical piles with small-diameter shafts, adhesion contributes little to the overall capacity and torque of the pile, so PWP changes are not typically considered in determining pile capacity. In modern construction, the use of larger diameter helical piles has become very common. For large-diameter helical piles, changes in PWP immediately adjacent the shaft can be quite large during installation. Increased pore water pressure and reduced adhesion can have a temporary effect on pile capacity and installation torque.

Jan 1, 2018

By Patrick J. Coleman, John C. Kerkering

Problem: Mining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injury rates over the last century. Coal mine fatality rates, for example, have dropped almost a thousand fold since their peak in 1908. While incidence rates are very important indicators, lost worktime measures offer an alternative metric for evaluating job safety and health performance. The first objective of this study examined the distributions and summary statistics of all injuries reported to the Mine Safety and Health Administration from 1983 through 2004. Over the period studied (1983 2004), there were 31,515,368 lost workdays associated with mining injuries, for an equivalent of 5,700 person years lost annually. The second objective addressed the problem of comparing safety program performance in mines for situations where denominator data were lacking. By examining the consequences of injuries, comparisons can be made between disparate operations without the need for denominators. Total risk in the form of lost workday sums can help to distinguish between lower and higher risk operations or time periods. Method: Our method was to use a beta distribution to model the losses and to compare underground coal mining to underground metal/nonmetal mining from 2000 to 2004. Results: Our results showed the probability of an injury having 10 or more lost workdays was 0.52 for coal mine cases versus 0.35 for metal/nonmetal mine cases. In addition, a comparison of injuries involving continuous mining machines over 2001 2002 versus 2003 2004 showed that the ratio of average losses in the later period to those in the earlier period was approximately 1.08, suggesting increasing risks for such operations. Discussion: This denominator free safety measure will help the mining industry more effectively identify higher risk operations and more realistically evaluate their safety improvement programs. Impact on Industry: Attention to a variety of metrics concerning the performance of a job safety and health program will enhance industry's ability to manage these programs and reduce risk.

Effect of Anionic Surfactant on Silica Particle Attachment at the Oil-Water Interface Controlling particle attachment is crucial where powdered solids come into contact with oil and water. Particles are trapped in a deep energy well at the oil-water interface, stabilising emulsions. Here it is shown that adding anionic surfactant causes dramatic changes to the bulk and interfacial structure of silica particle-stabilised oil-in-water emulsions. Exposing particle-stabilised drops to surfactant concentrations above the critical micelle concentration enhances the rate and extent of creaming and flocculation. Mixing particle-stabilised emulsions with surfactant solutions causes drop fragmentation. As the surfactant concentration increases, the average drop size decreases and particles are displaced from the interface during the mixing process.

Sep 13, 2010

By Ali Porbaha

Rapid growth in the urban development requires continuous search for innovative technologies to construct complex infrastructure systems. Deep mixing is one promising construction technology that has a wide spectrum of applications for development and expansion of complex urban facilities. Large number of reported case history of the projects in Europe, Japan, and the US demonstrate the versatility of the technology compared to conventional methods of ground modification. A large number of factors influence the quality of the soil cement columns; some of these are rooted in the installation process and the effective use of machinery during construction. This paper attempts to present some issues related to installation of deep mixing that affect quality of the treated columns. Presented here are various installation patterns, installation machinery, installation sequence, effect of penetration/withdrawal injection methods, penetration/withdrawal speed, effect of number of shafts, rotation of the blade, shape and orientation of mixing tools, and rotational speed of the shaft on quality of the treated ground.

Jan 1, 2001

By C. L. Lewis

"The development of computer process control at the Lake Dufault concentrator is reviewed and the on-stream X-ray analysis -computer system is described briefly. Some applications of the computer in metallurgical process control are described.The computer sequences slurry sample streams to the analyzer and translates the analytical results from voltage signals to elemental percentages. The required flotation reagent flow rates are calculated from analyses and mill-feed tonnage rates and the reagent feeders are set automatically to provide such flow rates. X-ray calibration time has been reduced from about 45 minutes to 15 minutes by the use of a computer program. Metallurgical and operating personnel have acquired the ability to program the computer and have extended the system capability to allow the calculation of recoveries, averaging of mill data, application of ore specific gravity in grinding control, control of oxidized ore flotation and the development of an economic recovery program."

Jan 1, 1971

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

By K. L. Murphy, G. Multamaki, P. M. Huck

"A preliminary evaluation, based on existing data, has been made of the implications of placing radium-barium sludge in tailings areas. The study was restricted to a consideration of possible increases in the quantities of radionuclides escaping to the environment through either groundwater or surf ace water, considering the types of tailings treated and the effluent treatment systems currently operating in Canada.IntroductionIn the recovery of uranium from ore deposits, the tailings produced by mine/mill complexes are conveyed to impoundment areas in slurry form. After settling, the supernatant is discharged to the environment together with runoff from precipitation on the tailings bas in. Currently, all operating uranium mines in Canada employ barium chloride treatment to control the release of dissolved radium to the aquatic environment. The dissolved radium in the tailings decant is precipitated with barium chloride, forming (Ra,Ba)SO4, and allowed to settle in ponds or lakes. In some instances, settling tanks have replaced ponds and flocculants have been added to aid settling. Because the Atomic Energy Control Board does not consider the precipitation ponds to be suitable for final disposal of these sludges, acceptable sites must be found. Options which have been suggested for sludge management include underground placement either in worked-out mine areas or in special chambers, or placement in the tailings areas. Conceptually, the latter alternative is attractive and probably would minimize sludge handling. This alternative would be subject to the AECB policy which requires that upon abandonment, radioactive releases from a tailings area must be within present regulatory limits and that treatment to meet these limits should not be required in perpetuity.No quantitative data exist concerning either the effect of physical and chemical conditions in the tailings on resolubilization of radium from precipitated sludges or the fraction of this additional radium which would be released."

Jan 1, 1982

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By PAUL L. FISHER

This bibliography has been compiled by the Bureau in answer to many requests now being received for information on the briquetting coal and other carbons . In addition to publications issued by the Government in printed or mimeographed form, references are included to articles appearing in the technical press and in cooperative reports of work done jointly with states , colleges , and industries . References and patents are arranged in chronological order . Bureau of Mines bulletins , technical papers and Minerals Yearbooks are printed , and are obtainable from the Superintendent of Documents ,. Government Printing Office , Washington 25 , D. C. Reports of investigations , information circulars , and the directories and reports of the mineral industry surveys are published in mimeographed form and may be obtained without charge from the Publications Distribution Section , Bureau of Mines , 4800 Forbes Street , Pittsburgh 13 , Pa . Many Bureau of Mines publications , as well as bound copies of the foreign and American scientific and trade periodicals , may be consulted in technical , college , and large public libraries throughout the country. Dealers in new and second-hand books sometimes have copies of these reports for sale .

Jul 1, 1948