Search Documents

By Malti Goel

"Ferrous and Non-ferrous industry in India is undergoing a transition to meet the growing demand and a new thrust to Research & Development (R&D) is mounting. On one hand, to meet the target laid by the policy in the Iron and Steel sector of 110 million tones production by 2020; on the other, innovations taking place in light metal production technology; both have necessitated greater attention to development of industrial ecological framework. Industrial ecology provides a number of new challenges as well as opportunities for the industry. The development and growth in a particular industry should have a trend towards reduced energy consumption, reduced resource consumption, thereby reducing the cost of production. Technology management strategies will have a key role in achievement of these targets. The paper describes recent developments in technology management, importance of R&D and case studies on adoption of energy efficient & CO2 reduction technologies in metal industry in India. In the end suggestions for future are made.IntroductionInternational Energy Agency [1] has assessed that nearly one third of the World’s energy consumption and 36% of CO2 emissions are attributed to manufacturing industries. In case of ferrous and non-ferrous metals, the resource equality and product quality finally determine the energy share across the countries. In the overall, Iron & Steel industry accounts for about 19% of total industrial energy used. The saving potential for non-ferrous metals is estimated to be anywhere between 13 to 25 % of the energy consumed depending on the level of resource quality. The projections are that energy consumption worldwide in Industry sector would increase 1.8% per annum up to 2030 on average, and up to 2.5% in developing countries."

Jan 1, 2008

By Shufeng Yang, Anping Dong, Yongfeng Chen, Jingshe Li, Lifeng Zhang, Liyuan Sun

"Instead of nickel-based stainless steel, a nitrogen-bearing stainless steel was produced to reduce the production cost stemming from the shortage of nickel recourses. Thermodynamic model to calculate the saturation nitrogen content in the stainless steel were developed and the model was validated by experimental measurement. The experiments were performed with a high temperature induction furnace. Nitrogen gas under constant pressure was injected into the crucible with a top lance by which the nitrogen was transferred to the molten stainless steel. The effects of chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were investigated and discussed.IntroductionWith the rapid production growth of stainless steels, nitrogen-bearing stainless steel has recently attracted more and more attention for their high strength and excellent corrosion resistance imparted by interstitial nitrogen without decreasing its toughness and ductility. Moreover, the addition of nitrogen to the stainless steel as a substitute for nickel leads a lower consumption of nickel, so significantly lowers the high production cost stemming from the shortage of nickel recourses. However, production of the nitrogen-bearing steel is difficult since nitrogen is a gas element and has a low solubility in the steel. So efficiently increasing the amount of nitrogen in steel continues to be one of the main concerns for the production of nitrogen-bearing steels.Currently there are some special processes to produce austenitic stainless steels with a very high N content, including pressurized electroslag remelting, counter-pressure casting, special induction melting and powder metallurgy, etc [1]. Special expensive vacuum system was required for these processes. Alloying nitrogen at a normal pressure can be performed by alloy addition or gas injection. Blowing nitrogen gas is a more economic and advisable method since the nitrogen-bearing alloy is quite expensive and contains high content of impurities. A number of investigations have been reported on the solubility of nitrogen gas in pure iron [2] but few in iron-based multi-component alloys such as stainless steel.In the current study, the effects of steel chemical composition, temperature, superficial active elements and nitrogen-flow rate on transferring nitrogen to the steel were experimentally investigated with a high temperature induction furnace."

Jan 1, 2011

By Linfeng Zhou, Yuanbo Zhang, Rong Sun, Guanghui Li, Zhiwei Peng

The volatilization behavior of rhenium in the process of oxidative roasting of a molybdenite concentrate with 43.55 wt.% Mo and 321 g/t Re is explored based on identifying the relationship between volatilization of sulfur and rhenium. The results show that rhenium volatizes after sulfur and precise control of operating variables plays an important role in separating rhenium from molybdenite concentrate. When the roasting parameters are optimized as follows: roasting temperature 600 oC, roasting time 2 h, roasting atmosphere air, the volatilization rate of rhenium reaches 89.26%. In the process of solidification roasting, the volatilization rate of rhenium decreased almost to zero when the ratio of slaked lime/molybdenum concentrate was 10% excess to the stoichiometric requirement at 600 oC for 2 h.

Jan 1, 2016

By B. Abedian, L. M. Racz, S. R. Berry, R. W. Hyers

"The presented work represents an effort to improve understanding and prediction of turbulent flow inside electromagnetically-levitated droplets. We show that the flow field in a test case, a nickel droplet levitated under microgravity conditions, is a low Reynolds number turbulent flow, i.e. in the transitional regime between laminar and turbulent. Past research efforts have used laminar, enhanced viscosity, and k - E turbulence models to describe these flows. In our study, we compare the RNG algorithm to laminar and k - E turbulence model results. We show that accurate description of the turbulent eddy viscosity µr is critical in order to obtain realistic velocity fields, and that µr cannot be uniform in levitated droplets. In the RNG method there are no characteristic length or time scales associated with the flow, thus allowing such anisotropic features to be captured. We perform calculations and analyses for two cases (1) a small, non-deforming, spherical nickel droplet and (2) a deforming, oscillating droplet. In addition to flow field calculations, we compare numerically-obtained surface tension and viscosity values to those obtained experimentally by the oscillating drop technique.IntroductionElectromagnetic levitation (EML) is a containerless processing technique for conductive materials. Its advantages are the avoidance of contamination or chemical reaction at container walls and the ability to perform long-term experiments in a metastable state. Because of its current limitation to small sample sizes, its primary use is in the laboratory. One application of interest is the measurement of thermophysical properties of undercooled liquid metals [1, 2, 3, 4]. In EML, a sample weighing approximately 1 gram is positioned inside an electromagnetic field generated by alternating currents flowing through an axisymmetric water-cooled copper coil. The coil must be designed appropriately so that thesample levitates in a stable manner.Traditionally, mathematical modeling has been performed in tandem with both earth-and spacebound electromagnetic levitation experiments, in order to determine the effect of the magnetic field on material and flow characteristics [5, 6, 7, 8]. These calculations are important because they allow design, planning, and correct interpretation of experiments. In addition, the calculations are of fundamental scientific interest, as they can be applied to other electromagnetic materials processing applications [9]."

Jan 1, 1999

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters, However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty, Ltd. in Australia.

Jan 1, 2003

By Moto Goto

Today, Pierce-Smith converters, coupled together with various types of smelting units, are used in most of the world's smelters. However, due to the "batch" processing nature, and problems associated with fugitive emissions during the transfer of melt and blowing stages, this arrangement will unlikely be adopted in future smelters. Modern day alternative processes include the Mitsubishi Process, Outokumpu Flash Smelting and Flash Converting Process, the Noranda Process, and the Ausmelt Process, but only the Mitsubishi Process is a "truly continuous" smelting and converting operation, producing a constant flow of blister without tapping, and is economically proven by long term commercial operations. This paper reviews recent advances in modern continuous converting technologies, with a special section devoted to operation of the "first standalone Mitsubishi C-furnace" coupled together with a Noranda Reactor, at Port Kembla Copper Pty. Ltd. in Australia.

Jan 1, 2003

By Sumantra Mandal

The hot deformed microstructure of the 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel (commonly known as alloy D9) was investigated employing electron backscatter diffraction (EBSD). Hot compression tests were conducted in a Gleeble thermo-mechanical simulator at temperatures of 1173K-1373K (in steps of 100K) with a strain rate of 10 and 100 s-1 to different strains. Various kinds of deformation patterns were observed inside the deformed grains. These were inferred as the development of geometrically necessary boundaries or formation of parallel set of micro-bands. Recrystallized grains were partitioned from the deformed grains employing grain orientation spread approach. Extent of dynamic recrystallization (DRX) was found to be minimal at 1173K. DRX was predominantly found to happen at and above 1273K which increases with increase in strain. DRX nucleation and development mechanisms were discussed with respect to bulging of the parent grains and sub-grain rotation. Special emphasize is given on the role of annealing twins on DRX nucleation and subsequent expansion.

Jan 1, 2009

By Guy Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity' (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By G. Gao

Flyash from municipal solid waste (MSW) incinerators is frequently classified as a characteristic hazardous waste due to its lead and cadmium content. Extensive investigation has therefore been carried out to detoxity the flyash by leaching and to recover lead, cadmium and zinc. Detoxification can be accomplished by leaching in HCI/NaCI solutions. Optimization of leaching conditions for effective detoxification and subsequent metal recovery can be achieved by controlling the acidity of the lixiviant and flyash to lixivaint ratio. Lead and cadmium In the leaching solution is recovered by cementation with zinc dust. Leaching and cementation experiments have shown that zinc concentrations suitable for electrowinning, > 15 g/liter, can be achieved. Experiments have also been performed to determine the effects of pH, particle size of the zinc dust used, quantity of zinc added and dissolved impurities on the cementation kinetics. After recovery of lead and cadmium, electrowinning or electrowinning coupled with solvent extraction can be used to recover zinc. A process flowsheet is presented.

Jan 1, 1991

By Felipe Daroch, Maria C. Ruiz, Rafael Padilla

Copper concentrates with high arsenic contents must be pretreated before conventional smelting to prevent environmental pollution with arsenic compounds. In this work, experimental results concerning the selective removal of arsenic and antimony from copper concentrates are presented. The process consists of an alkaline digestion using concentrated NaHS-NaOH solutions to transform the arsenic and antimony sulfides into soluble compounds. A water leaching follows the digestion to dissolve the arsenic and antimony, leaving clean copper sulfide solid residues. The laboratory scale tests were carried out using a copper–arsenic concentrate with 15.05% As and 1.42% Sb. The results showed that the most important digestion variables were temperature and concentrations of NaHS and NaOH. Over 97% of arsenic and 92% of antimony could be removed in 10 min of digestion using 8.9 M NaOH and 100% excess of NaHS at 80 °C. The subsequent water leaching was performed at 80°C for 20 min.

Jan 1, 2015

By Hu Long

In this, the first systematic study of the oxidation of orpiment (As2S3) in sulfuric acid solution under oxygen pressure at temperatures above 170°C, the effects of retention time, temperature, particle size, oxygen partial pressure, the concentration of sulfuric acid and pulp density were evaluated. The effects of cupric and ferric ions on the oxidation rate of As(III) to As(V) were also examined. The products of oxidation are As(III), As(V), SO42- and elemental sulfur. At temperatures ranging from 170 to 230°C, most of the arsenic was found to be in the trivalent state, and oxidation to As(V) with oxygen was very slow. This was confirmed by attempting to oxidize a synthetic arsenious solution. However, the rate of oxidation of As(III) to As(V) is rapid in the presence of ferric ion. Elemental sulfur was found at all temperatures investigated, which can be further oxidized to sulfate at high temperature.

Jan 1, 1999

By Richard D. Hangi

Process mineralogy techniques are uniquely applicable to industrial problems related to the extractive metallurgy of nickel, cobalt, and associated metals. Reflected 1ight microscopy, together with selected determinations by scanning electron microscopy-energy dispersive spectrographic analysis and electron probe microanalysis, provides the means to identify the ore minerals cobalt and nickel ores, determine the abundance of each ore mineral, assess the extent of intergrowth between the cobalt and nickel minerals and other ore and gangue minerals in the ores and concentrates, and predict the potential success of cobalt and nickel extraction by grinding, flotation, pyrometallurgical, and hydrometallurgical treatments. In addition, the extent of locking of the cobalt and nickel minerals with each other and with the gangue minerals can be directly observed by reflected light microscopy. Where ores have been treated by hydrometallurgical procedures, reflected light microscopy can serve to determine the causes of excessive leach consumption. Finally, the partitioning of cobalt and nickel between high-temperature synthetic phases produced by pyrometallurgical treatment can be precisely determined by process mineralogy techniques. Case histories from cobalt and nickel deposits illustrate the value of applied mineralogical techniques in the study of cobalt and nickel ores, beneficiation, hydrometallurgial, and pyrometallurgical products.

Jan 1, 1993

By Junli Xu, Xianwei Hu, Kaiyu Xie, Liangxing Li, Zhongning Shi, Zhaowen Wang, Bingliang Gao, Aimin Liu

Al-Ti master alloys were prepared by aluminothermic reduction between the dissolved titanium dioxide and aluminum in cryolite melts at 960oC. The kinetic analysis by differential scanning calorimetry indicated that the apparent activation energy of the reaction of reducing titanium dioxide by aluminium is 22.3 kJ/mol, and the reaction order is 0.5. The products were analyzed by means of X-ray diffraction, X-ray fluorescence, scanning electron microscopy and energy dispersive spectrometer. Results from X-ray diffraction showed that the phase compositions of produced alloys are Al and Al3Ti. In addition, Al-Ti master alloys containing 2-6 mass% Ti were formed at different reduction time of 2-5h in aluminothermic reduction experiment.

Jan 1, 2015

By S. P. Jupp

A 2-D coupled thermo-mechanical model was developed to simulate hot tandem rolling of AA5056 aluminum alloy using the commercial finite element software package, ABAQUS The model was used to predict the temperature, strain rate and strain distribution in the strip at any position in the roll bite and was verified through comparisons with literature results in terms of both temperature and strain predictions at the roll bite exit. A sensitivity analysis indicated that model predictions of temperature and strain at the roll bite exit were sensitive to the friction coefficient and moderately sensitive to the heat transfer coefficient for the conditions studied. Microstructure equations taken from the literature were used to make predictions at various positions in the strip. The temperature, strain rate and strain vary dramatically through the thickness of the strip in the roll bite. The sensitivity of the microstructure predictions to these parameters was assessed and it was found that using average values of temperature and strain rate in the roll bite versus exit values significantly influenced the resulting microstructure predictions.

Jan 1, 2001

By G. G. Richards

The zinc slag fuming process is used to recover zinc from molten iron-calcium silicate slags by treatment with pulverized coal and air. The rate of zinc fuming is controlled by the complex interaction of several kinetic factors including the rate of entrainment of coal in the slag, the extent of the coal-slag reaction and the rate of ferrous oxide oxidation to ferric oxide. This paper briefly outlines the mechanism of fuming and, on this basis, optimization of process parameters is discussed. Modelling analysis and recent industrial trials at Cominco show that coal entrainment in the slag, bath temperature, and bath depth are critical variables affecting process rate and efficiency. The first step in process optimization is to assess coal bypass of the bath. In general, changes which promote operation at a higher temperature, greater coal entrainment in the slag and extended residence time of the coal in the bath increase fuming performance. Coal entrainment is controlled by injection conditions whereas bath temperature is a function of coal combustion and ferrous oxide oxidation. Residence time of the coal is largely a function of bath depth. The implication of model predictions for continuous fuming is shown.

Jan 1, 1994

By Bogidar Mihaylov

A laboratory study was conducted on continuous precipitation of copper, cadmium, mercury and arsenic using thiourea, thioacetamide, sodium sulfide and ammonium sulfide as precipitating agents. Depending on the experimental conditions the metals precipitate with the sulfide donors at different orders and rates. These differences were employed as a basis of several techniques for continuous separation of copper and arsenic, cadmium and arsenic, mercury and copper, and copper, mercury and arsenic. The separation of the metals from industrial waste solutions was also studied. The precipitates obtained were inspected using x-ray diffraction, scanning electron microscope, atomic absorption spectrometer and plasma particle counter.

Jan 1, 1992

By Zhanjun Wang, Yongqi Sun, Mei Zhang, Zuotai Zhang, Min Guo

The role of fluorine on the viscous and crystallization behavior of CaO-SiO2-MgO-Al2O3-FetO-P2O5-(CaF2) slags were explored using the rotating cylinder method, non-isothermal differential scanning calorimeter (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. It was found that the viscosity slightly decreased with increasing CaF2 content. It was also found that CaF2 addition can promote the primary phase transformed from MgFe2O4 spinel to Ca3(PO4)F, which was beneficial to the enrichment of phosphorus. Additionally, the structure of the slags explained by X-ray photoelectron spectroscopy (XPS) and magic angular spinning nuclear magnetic resonance (MAS-NMR) were further analyzed, which was well in accordance with the above analysis.

Jan 1, 2016

By Zhou Aiping, Lv Guozhi, Niu Liping, Wang Wenbo, Zhang Ting’an, Jiang Xiaoli

The current method used to produce sponge titanium utilizes a process cycle of magnesium metal and chlorine gas via the electrolysis of magnesium chloride. The primary issues are the high capital cost of the electrolysis process and the environmental regulations limiting high chloride concentrations. Thus, the authors have developed a conceptual method involving theelectrolysis of magnesium chloride as well as a reduction process which allows for a cycle of magnesium and chloride. In the new method, MgCl2 which was distilled during the titanium extracting process as raw material was directly pyrolyzed at elevated temperatures yielding high purity magnesium oxide and chlorine. The resulting magnesium oxide can be used in the production of magnesium metal. This work examines and compares the energy consumption and economic benefits of the Kroll method as well as the new proposed method. The results from the study demonstrated that in comparison to the traditional Kroll method, the new method provided considerable economic and environmental benefits.

Jan 1, 2014

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By I. Gaballah

The chalcopyrite ore's anodic and cathodic electrodissolution are studied using a Porous Pulsed Percolated Electrode (3PE) reactor. Stationary solid electrode experiments are also performed to explore the mechanism of electrochemical dissolution of chalcopyrite. Experiments with a low - grade natural ore have been carried out at 25 "C in solutions containing 1 M NaCl and 1 M HCl. Galvanostatic and potentiostatic conditions are employed. The influences of current and potential on selectivity of the chalcopyrite ore dissolution are assessed. Anodic oxidation of this ore leads to a preferential dissolution of iron bearing minerals, whereas cathodic reduction is more selective with respect to chalcopyrite. However, in both cases the electrochemical dissolution is incomplete and the current efficiency is low. Design of the actual reactor has to be modified to increase the bed conductivity and to allow continuous experimentations.

Jan 1, 1994