Search Documents

By Nobumasa Kemori

Six kinds of copper '90ncentrates. were treated individually in a ,pilot scale. Outokumpu flsah smelting furnace ~n order to study their ?flash smelting behavior with respect to oxygen efficiency and dust generation. The copper concentrates tested were selected from the more than twenty sources which are treated at the Sumitomo Toyo copper smelter, so as to provide a wide range of chemical composition in terms .of Cu, S,Fe, Pb + Zn + As, and Si~ content. Oxygen efficiency 'and dust generation rates obtained in 'the experiments ranged from 80% ,to 108% and 11% to 20%, respectively. Relationships between these results and experhnental conditions such as chemical and mineral composition of the copper concentrates, flux ratio, fuel consumption and so on are also discussed quantitatively in this paper.

Jan 1, 1998

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By W. L. Dalmijn, J. M. Krowinkel

A recycling concept of end-of-life televisions starting with shredding will produce a complex material mixture, very heterogeneous in size, shape and degree of liberation. Basically all materials in television scrap are valuable, which means that recovery is important for either economic, environmental or sustainability reasons. However glass, plastics and metals are the materials with the highest potential for recovery. Non-magnetic materials from shredded television sets can be separated into three characteristic size fractions that need further separation for a high value-added recycling of the materials. This study investigated the potential of physical separation of these size fractions into valuable material streams using polyseparator, tlrldy current separator, dry and wet shaking tables and electrostatic separator. An overall mass balance of the mechanically processed televisions was calculated. Evaluation of the produced material fractions showed that heterogeneity in particle shape and size together with the presence of unliberated materials caused sever difficulties in separation when exclusively based on mechanical techniques. The results indicate that a certain degree of dismantling is necessary to achieve products of appropriate quality in physical separation. In order to improve recycling of electronic scrap through design for recycling cooperation between the electronics industry, the manufacturers and the recyclers of electronic goods is necessary.

Jan 1, 2000

By Mark R. Jolly, Jean-Christophe Gebelin, Aleksander Cendrowicz

"Injection of wax patterns is the first stage of the multi-stage process of investment casting. The quality of the final casting and its dimensional accuracy is highly dependent on this stage of the process. Pattern waxes used in the industry behave in a complex visco-elastic-plastic manner. The modelling of such material behaviour is therefore not simple.In this paper a number of configurations of die will be shown in which the injection of the wax has been carried out for a range of processing conditions. Some of the dies are transparent and the movements of wax front observed can be compared with those predicted by simulation. Surface defects in final components will also be shown and compared with the location predicted by simulation software. Some discussion will be presented on the limitations of the software used and the time-scales achieved for practical use as a design tool within the foundry environment. IntroductionThis paper presents the research activities carried out at the University of Birmingham on the modelling and prediction of the behaviour of industrial investment casting waxes during the injection of wax patterns. These research activities are done in the context of a more global study of the fundamental aspects of the investment casting process, the FOCAST project. Regarding the wax injection process, the aim of the project is to achieve a better understanding of the key factors that will lead to better castings. The filling of the die during the injection has been studied. Some other phenomena such as shrinkage/warpage or creep under residual stresses are also studied, but not presented here. Two commercial investment casting waxes have been characterised in order to model their behaviour and predict mould filling and subsequent defects.This paper will present the models that have been used in our work, the simulation packages used, the experiments carried out to validate the modelling and exhibit the defects due to bad filling, and finally the numerical simulation results."

Jan 1, 2001

By Józef Czemecki

Polish copper concentrates are characterized by high levels of impurities, particularly Pb and As. Two technologies are being used for copper concentrate smelting at KGHM Polska Meidz S.A., namely the shaft furnace process (Legnica Copper Smelter, Glogów I Copper Smelter) and a single-stage process for direct to blister concentrate smelting in a flash furnace (Glogów II Copper Smelter). Both technologies are used at different physical and chemical conditions which results, in different impurities behavior. The paper presents flow sheets for copper production in a plant using the shaft furnace process and in another in which a single stage flash process is used. The metals distribution in particular semi-products is given as well as a method for elimination of impurities from the copper production cycle. Methods are also discussed for alloy and matte converting and copper refining to obtain low Pb and As concentrations in anode copper (0.3% Pb and 1500 ppm As maximum) that are being used in the KGHM Polska Meidz plants. Useful co-operation between the plants using different technologies, aimed at the limiting the effect of undesired impurities on the quality of blister copper produced, is also described.

Jan 1, 1998

By Svetlana Nikitina

While many question "sustainability" as an intellectual field on the grounds that it is too broad and "undisciplined," we are able to achieve a good balance between breadth of coverage and depth of inquiry in our team-taught seminar "The Grand Challenges: Sustainable Development for the 21st Century" offered to first year students at Worcester Polytechnic Institute. We strike this balance between breadth and depth by a) problematizing key sustainability issues in class discussions; b) by explicitly exploring the lenses of different disciplines (the historical context, the scientific facts, the engineering interventions and the philosophical foundations of unsustainable behaviors); and c) by offering our students opportunities to pursue a targeted project on specific sustainability issues (vertical gardening, metals recycling on college campus) through which they gain depth of understanding as well as practical exposure to all components of the problem, which puts them on the path of seeking effective solutions.

Jan 1, 2010

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By Sebastian Schmuck, Petrico von Schweinichen, Dieter Senk, Mohammad Peymandar

"At Department of Ferrous Metallurgy of the RWTH Aachen University in Germany steels in the system Fe-Mn-C(-Al) are investigated and produced in the framework of the SFB 761 ""steel-ab initio"". A new world of steel grades leads to special challenges regarding the production and recycling at the end-of-life cycle of product. In order to recycle high manganese steel alloys the EAF has to be chosen preferentially. A good slag practice is necessary avoiding loss of manganese content during melting in the EAF. This paper investigates on the reaction kinetics at the interface of slag and steel containing Mn (17-22 wt.-%) and up to 3 wt.-% Al. The effect of changes in the composition of slag and steel on the interfacial reaction kinetics is studied. The thermodynamic software FactSage™ is utilized to calculate the composition of slag and steel at equilibrium.IntroductionTRIP and TWIP steels are highly alloyed steels which show superior strength and ductility when compared to standard carbon steel and stainless steel alloys. These TRIP- and TWIPsteel grades contain typically 15-30 wt.-% manganese, 0-4 wt.-% silicon and aluminum, and up to 1 wt.-% carbon. Steels containing 18-28 wt.-% manganese and 0.7-1.2 wt.-% carbon together with aluminum addition from 3 to 12 wt. -% and without silicon refer to TRIPLEX high manganese steel alloys. These alloys combine high strength at even large ductility [ 1-4]. At the Department of Ferrous Metallurgy (IEHK) of the RWTH Aachen University in Germany, steels in the system Fe-Mn-C(-Al) is under investigation at the collaborative research center, SFB 761 ""Steel-ab initio"". In this project, high manganese alloyed TRIP and TWIP steels are in the focus.The mechanical properties such as high strength and high ductility make this kind of steels perfect candidates for impact absorption applications in auto body such as vehicle doors and bumpers [2, 5]. With increasing the use of TRIP-, TWIP- and TRIPLEX-steels more high manganese steel scraps will be available at the end of life cycle of products, which need to develop the technologies and metallurgical processes to recovery of high manganese steel. A new steel grade brings new challenges in recycling. In order to recycle high manganese steel scraps the electric arc furnaces (EAF) have to be chosen preferentially [1]. Nevertheless it's not easy to prevent the manganese loss during the process in EAF. During the oxygen refining of high manganese molten steel in EAF the manganese content decreases strongly by oxidation and vaporization, which is affected by slag composition, slag properties such as basicity and viscosity, slag weight as well as melt temperature [6-8]."

Jan 1, 2014

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to predict the distribution behaviors of Ni, Co, Sn, Pb, Zn, As, Sb, Bi, Au and Ag in copper pyrometallurgical process. In this model, as more as 21 elements (Cu, S, Fe, Ni, Co, Sn, As, Sb, Bi, Pb, Zn, Au, Ag, 0, N, C, H, Ca, Mg, Al, and Si) and 72 compounds (in fayalite-slag-making system) or 74 compounds (in ferrite-slag-making system) are considered. Accessory-element behavior is studied for two types of slag , fayalite and ferrite, and two levels of oxidation. The allowance is also made to account for physical entrainment in the melts.-Model simulations are carried out to study the effects of controllable process parameters such as feed composition, smelting temperature, degree of oxygen enrichment and volume of oxygen enriched air. The model can be used in copper flash process, Mitsubishi process and Noranda process. The predictions by the present computer model are compared with the known industrial data from Gui Xi Smelter in China, Home Smelter in Canada and Naoshima Smelter in Japan and excellent agreement between calculations and industrial data is obtained. In this paper, the effects of oxygen enrichment, matte grade, smelting temperature, and types of slag on accessory-element behavior among matte, slag and gaseous phase have been elucidated.I . IntroductionThe presence of trace quantities of minor elements such as As, Sb and Bi in copper significantly reduces its ductility, electrical conductivity, and lowers its thermal conductivity. Embrittlement of copper also occurs due to impurity-phase precipitates at the copper grain boundary interfaces. They deteriorate not only the electrical conductivity of copper but its workability in hot working."

Jan 1, 1998

By Leith Sharp

I was confronted with a profound dilemma as an undergraduate engineering student at the University of New South Wales in Australia in 1992. I had been taught that our planetary life-support systems were in a state of alarming decline by an institution that operated as if what the faculty was teaching was irrelevant. Lights were left on in empty overcooled classrooms, recycling bins were nonexistent, lawns were maintained using pesticides and herbicides, diesel trucks spewed fumes as they passed on their way to drop off chlorine-bleached virgin paper. This disconnect was very alarming to me. While it was obvious that universities should play a leading role in teaching and researching sustainability issues, I wondered how it could be possible to make widespread institutional changes to meet the demands of environmental sustainability when it was not even being done in the very university sector where these ideas were being promulgated. If universities would not change, then who can and who will, I wondered? To a growing number of people, the idea of teaching sustainability without demonstrating it is highly problematic. It is also widely believed that the ability of the higher education sector to reform its own practices is an important indicator of humankind?s ability to address the global environmental imperative across all sectors of society. These sentiments have helped fuel what is now referred to as the campus sustainability movement, a movement dedicated to transforming our campuses into living laboratories for the demonstration and practice of environmental sustainability.

Jan 1, 2010

By B. R. Davis, Neale R. Neelameggham, R. E. Brown

The element Calcium element has a unique place in the production of etals, intermetallics and other compounds. The unusualness arises from the fact that we have several possible reductants – metallic calcium, calcium carbide, calcium cyanamide and calcium hydride. A review of how metallic calcium is manufactured and utilized is presented. The difficulties involved in producing the metal in large quantities and price implications are noted. . Fundamental thermodynamics of how these act as reductants are shown, along with the historic application of these in metal production during the past century and a half. Alternate applications as to how to control the cost of the reductant is indicated, such as the numerous attempts in making low cost titanium utilizing direct or indirect calcium reductant.

Jan 1, 2014

By Liyuan Chai

In this study, spent grain was used as an adsorbent for the removal of Hg(II) from aqueous solutions, the process parameters such as contact time, solution pH, adsorbent dose, and initial Hg(II) concentration were studied in batch experiments. The initial adsorption process was fast, 91.08% of adsorption occurred within 5 min and equilibrium was reached at around 30min. Adsorption process was found to follow pseudo-second-order kinetics. The equilibrium data were better fitted to Langmuir isotherm than Freundlich isotherm with the maximum adsorption capacity 41.36 mg/g. The structure and component of spent grain before and after adsorption of Hg(II) were investigated using scanning electron microscope(SEM) and energy dispersive X-ray analysis(EDAX), these analysis also confirmed the adsorption of Hg(II) onto spent grain. The results indicated that spent grain had potential as a new inexpensive adsorbent for Hg(II) removal from aqueous solutions.

Jan 1, 2009

This paper outlines the complete failure of the U.S. in status and relevance in Rare Earth Oxides (REO). Although rare earth oxides are strategic and critical in their own right, refining these REOs into elements and alloys is even more important for the development of "Green Technologies" and advanced weapons systems. America does not have an active domestic source of rare earth oxides. America does not have any heavy rare earth elemental or alloy capabilities. The magnitude of this failure continues to become more apparent as the manufacture of REO based electronics and magnetic components moves eastward towards China. China has succeeded in outmaneuvering the United States and the world in its quest to control the rare earth oxides, elements and alloys, and the many industries dependent upon REO. What can be done?

Jan 1, 2010

By R. M. Taylor

Lime addition to acid mine drainage (AMD) leads to precipitation, predominantly of metal hydroxides and calcium sulfate, and is the benchmark for remediation by precipitation. Geo2 Limited of Melbourne, Australia has developed and patented a novel alternative precipitation scheme based on the formation of mixed valency, M(I1)-M(III), hydroxide sulfate salts. When the composition of AMD is appropriate, the Green Precipitate Process provides a useful and more effective alternative to conventional liming. The characteristics and utility of the Green Precipitate Process are described in terms of the underlying chemistry, and a case study where the Green Precipitate process outperforms conventional liming. A mobile pilot pipe reactor rig which was built by Geo2 to demonstrate the process, and used successfully in both Australia and the United States, is described.

Jan 1, 1998

By Jian Zhang

From the standpoint of quality, surface cracks normally pose more of a problem than internal cracks. Hypo-peritectic (HP) steel grades are well known for their proneness to surface longitudinal cracking (SLC) during continuous casting. This study analyzed the influences of chemical composition, technique parameter and secondary cooling on the surface longitudinal cracks. Based on the optimized the first and secondary cooling zone water distribution in the process of continuous casting, low cooling water distribution at solidification initial stages and uniform cooling at secondary cooling zone were suggested, which can be used to effectively control the surface longitudinal cracks.

Jan 1, 2010

By Melissa L. Trapani

Keywords: Copper, Taphole, Flow Instability. ?Blister spitting? is a flow irregularity where the molten blister copper stream ? or part thereof ? sprays from the taphole exit rather than following a regular flow profile to the collection box. As well as being a general ?housekeeping? issue, the unpredictable nature of the flow is a threat to operator safety. Also, the aggressive flow pattern may contribute to the mechanical wear of the taphole refractory, compromising the integrity of the taphole. This paper brings together a collection of first-hand observations and reports from process personnel, and suggests some theories as to the causes of blister spitting.

Jan 1, 2005

By N. L. Piret

Primary and secondary copper smelting dusts are being generated in varying quantities with very dissimilar characteristics due to the different compositions of feed materials and the type of process utilized. After categorizing the multitude of dust types, the criteria for on-site and off-site recycling of smelter dust in terms of type and concentrations of the accompanying elements are established. Thereby, consideration is given to the important aspects of: ? optimization of copper recovery ? quality of copper product ? valorization of accompanying elements ? elimination and disposal of deleterious impurities ? minimization of impact on operation ? effects on operating costs ? environmental impact of dust treatment on overall process Existing commercial, emerging and proposed copper smelting dusts, pyrometallurgical as well as hydrometallurgical, treatment schemes are reviewed and evaluated technically, economically and environmentally in an attempt to streamline the vast number of proposed options. Thereby, the high selectivity achievable in hydrometallurgical dust processing due to it being complementary to the smelting process is expected to be given increased consideration.

Jan 1, 1995

By Sepp Härkki

The energy crisis in Finland after World War I1 together with a sharp rise in the price of energy caused Outokumpu Oy to consider replacing the electric furnace smelting of copper concentrates by some other method. The flash smelting method developed under these circumstances offered a considerable saving of fuel through the utilization of the reaction heat of sulphides and yielded a high recovery of sulphur in the form of acid. The pilot plant testing of the new process was carried out in the years 1947 - 1948. The process was adopted for the smelting of copper concentrates (1) (2) (3) on a commercial scale in 1949 and applied successfullv to the smelting of -nickel concentrates' at the Harjavalta Works in 1959 (4) (5) (6). In 1962 Outokumpu adopted another type of flash smelting where elemental sulphur is recovered from the gases after the thermal decomposition of pyrite in the flash smelting furnace (7) (8): In recent years, the copper-nickel flash smelter and pyrite process have been combined to produce elemental sulphur instead of SO2 from the smelter gases (9) (10). The basic idea of the Outokumpu flash smelting process for sulphidic ores is that the conventional methods with separate roasting and smelting operations are replaced by a combined roasting, smelting and part-converting process carried out in one unit. The heat generated from the exothermic reactions can thus be used for smelting the ore so that only a small amount of additional fuel is needed. The characteristic of the method is also that the dried, fine-grained concentrate is smelted in suspension, which offers the best conditions for rapid reactions. The recovery of waste heat from the furnace off-gases had been considered already in the original flash smelting system. A

Jan 1, 1976

By Alistair Burrows

Situated in the oblast of East Kazakhstan, the Ust-Kamenogorsk Metallurgical Complex has spent the past twenty years renovating and remodelling itself as a modern polymetallic sulphide smelting facility, and a regional centre of excellence for custom smelting. Along the way there have been changes to the company structure, introduction of new technologies, investments in expanded capacity, environmental improvements, and addition of new metal products and by-products to the site’s repertoire. These changes have been gradual and incremental, but taken together they represent a significant contribution to placing Kazakhstan’s sulphide smelting industry on a strong foundation for enduring success in the international custom smelting market. In achieving these changes, a workforce that was historically isolated from much of the world now has recognised expertise, internationally competitive skills, and confidence to embrace the future. Further improvements in energy efficiency, environmental compliance and polymetallic processing capabilities are challenges that UKMC stands ready to face.

By Raymond E. Healy

Mercurian e1ectrum (Au-Ag-Hg alloy) is the principal Au-bearing phase in the massive sulphide ores at Trout Lake, Manitoba. The average composition of this phase (in wt %) is 49.2 % Ag. 38.7 % Au and 11.0 % Hg, with ranges of 17.34 to 76.47 % Ag, 1.62 to 79.86 % Au and 1.29 to 30.87 % Hg. Compositional variation reflects solid solution in the a-phase of the Ag-Au-Hg system. Backscatter electron imagery reveals systematic zoning and suggests a general crystallization sequence from metamorphic pore fluids of progressively Ag-rich compositions. Investigation of the occurrence of gold in mill products demonstrates that mercurian electrum accounts for over 90 % of the Au in Trout Lake ore. I Invisible" gold in pyrite (x = 0.72 ppm Au) and arsenopyrite (x 30.2 ppm Au) is confirmed by SIMS analyses, and accounts for 7-10 % of the Au in the ore, and 35 % of the Au lost to the tailings. The remaining 65 % of the Au lost to the tailings consists principally of mercurian electrum locked with pyrite. No significant losses of mercurian electrum in the size range amenable to flotation and/or regrinding is indicated.

Jan 1, 1989