Search Documents

By F. Michael Hosking

Modeling of a furnace brazing process is described. The computational tools predict the thermal response of loaded hardware in a hydrogen brazing furnace to programmed furnace profiles. Experiments were conducted to validate the model and resolve computational uncertainties. The results from selected furnace simulations and measured thermal events were compared. Critical boundary conditions that affect materials and processing response to the furnace environment were determined. "Global" and local issues (i.e., at the furnace/hardware and joint levels, respectively) are discussed. The ability to accurately simulate and control furnace conditions is examined.

Jan 1, 1998

By Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery

The determination of reduction degree in a DR process is sensitive to the total iron in the ore and DRI. An accurate and high throughput analysis method for total iron has been developed. Titration of the solution after tin(II) chloride reduction of ferric ion is a widely used method for iron analysis. However, it is a multistep method that requires many chemical reagents and much time. In this work, an ICP-OES analysis method with higher or equivalent accuracy compared with the titrimetric method was developed. This method has much higher throughput and demands fewer chemical reagents compared with the titrimetric method. In this paper, a comparison of the two methods is presented.

Jan 1, 2016

By R. N. O'Brien, E. Peters

"It has been discovered that copper concentrates can be leached in strong (40-60%) sulfuric acid with nitric acid, or with oxygen if nitric acid is present as a catalyst. Chalcopyrite is rapidly decomposed at temperatures well below the boiling temperature of the lixiviant (-150 C.) and the resulting copper and ferric salts are precipitated as CuS04.H20 and FeH(S04)z.4H20. Other metal sulfides such as zinc, lead, nickel, etc. are also converted to sulfates that are nearly insoluble. Sulfur is partially converted to elemental and partially to sulfuric acid. Reduction products of nitric acid can be recovered from the distillate with good recovery. Conversion of as-received copper concentrates is largely complete in about 1 hour. Introduction9 molar sulfuric acid is an unusual hydrometallurgical lixiviant: it has a boiling point of about 150 C. and a low solubility for base metal sulfates. Below about 6 molar acid, the boiling point falls below 120 C. and yields much higher sulfate salt solubility, while above 12 or 13 molar acid and at higher temperature sulfuric acid becomes an oxidizing agent, yielding gaseous S02' Thus, sulfuric acid within this range of concentration is capable of acting well above the temperature of boiling water without requiring autoclave conditions, and if typical oxidative leaching conditions are applied to suspended mineral sulfide concentrates, it is possible to obtain a conversion of these sulfides into 'crystalline sulfates. Thereafter, the sulfates can be separated by filtration or by solid - bowl centrifuge and the solution can be recirculated to the reactor vessel. Meanwhile, the solid sulfates can be treated in a typical hydrometallurgical circuit, i.e., dissolved in a return stream that is essentially water, separated from each other by, for example, solvent extraction, and recovered as metals by electrowinning."

Jan 1, 1997

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By Sergio T. Amancio-Filho

FricRiveting technique is an alternative new spot joining process developed for thermoplastic-lightweight alloy structures. In this technique a cylindrical metallic rivet is used to join one or more thermoplastic / metal components by means of plasticizing and deforming the tip of the rotating rivet through frictional heating. Advantages of this new technique are e.g. short joining cycles, minimal sample preparation, absence of environmental emissions and enhanced mechanical performance in comparison to base materials. Qualitative and quantitative synchrotron X-Ray microtomographic and light optical microscopic analysis of a case-study joint on aircraft materials polyetherimide and aluminum 2024 showed that joint strength is mainly dependent on aspect ratio of the rivet (geometrical dependence) and quality of joint, (microstructural dependence), whereby increasing aspect ratios and lowering the percentage of defects usually yield improved strength.

Jan 1, 2009

By Neil Rowlands

Particle liberation studies are commonly used in the determination of the proportion of locked and liberated phases in ground ores at various stages of mineral processing. These studies may range from a qualitative assessment of a polished specimen in an optical microscope to a full quantitative analysis of the liberation characteristics of fine grained complex sulfide ores using scanning electron microscopy and high level image analysis. However, the conversion of quantitative data to meaningful information on a mill operations level is by no means a simple task. This paper reviews the errors inherent in the SEM/Image Analysis technique and looks at the various methods available to minimize errors in data collection.

Jan 1, 1992

By J. McKelliget, J. Szekely, Oreper. G. M.

"1. INTRODUCTIONThis paper is concerned with heat and fluid flow phenomena in arc welding operations. Fig. 1 shows a schematic sketch of a typical arc welding arrangement. It is seen that an arc is being struck between an inert electrode and a metal surface and that the resultant current and energy flow will case the formation of a molten weldpool.It is clearly appreciated that the weldpool shape and the nature of circulation in the weldpool may play an important part in determining the ultimate weld quality. It is known, furthermore,· that the weldpool behavior in turn will be affected by the spatial distribution of the current and the heat flux it receives from the arc. Indeed, the inherent coupling between the arc and the weldpool is a key feature of welding operations.Up to the present useful work has been done on the modelling of heat transfer and melt circulation in weldpools (1,2,3,4) and also on the description of arcs, including welding arcs (5,6,7,8). However, the coupling between these two sets of phenomena is relatively unexplored in a qualitative sense. The purpose of the present paper is to examine the interaction between welding arcs and weldpools. The actual material will be presented under the following headings:"

Jan 1, 1986

By X. K. Lan

The greater demand for high-quality large-diameter crystals has led to the robust idea of a free- flying solar-powered furnace satellite, whereby the buoyancy-driven convection effects are almost nonexistent, and diffusion-controlled crystal growth with minimal radial segregation is promoted. In the proposed solar furnace, a paraboloid of revolution imaging concentrator is used to focus the sun's radiation onto an-ampoule which holds the solid charge to be processed. The charge will start melting in the vicinity of the focal point, after which it is translated in order for the melt to resolidify as a single crystal. A ray-trace method has been developed to determine the incident concentrated solar heat flux on the ampoule surface for a perfectly-aligned configuration with an incoming columnated beam. A transient 2- dimensional conduction problem with phase change is formulated, which is solved using the commercial code FIDAP. Results highlighting the feasibility of growing GaAs, Ge and Si crystals with diameters of the order of 20 cm using the solar furnace satellite concept are presented. The transient temperature fields within various charge materials are quantified.

Jan 1, 1994

By J. W. Matousek

In the flash smelting of copper sulfide concentrates, the course of reactions from the burner tip, through flame "burn-out" (the point of oxygen depletion), to settled matte and slag is of particular interest in understanding the mechanisms of the process. Numerous reaction sets can be proposed to describe the chemical changes that might be taking place, but from outside the furnace no one set offers an obvious advantage in explaining the actual processes involved. Only a combination of mathematical modeling and flame and bath sampling can achieve this result. This paper shows that flash smelting, while still reasonably orderly, is a more complex process than suggested by the technical literature.

Jan 1, 1993

By Robert Vidal

A model of the homogeneous chemistry and transport processes within the separator of a chrome-alum electrowinning cell is introduced, discussed, and compared to experiment. The influence of diffusion, electromigration, and convection are included; it is found that convection was the dominant mode of transport for the experimental conditions. Simulation results explain experimental observations concerning an apparent disappearance of dichromate ions produced at the cell anode. The relation between potential drop across the diaphragm and the current and fluid flow is also illustrated. The model is used to recommend future experimental and theoretical work.

Jan 1, 1994

By R. L. Nyirenda

An investigation of the reducibility of a cassiterite concentrate with charcoal was made in the temperature range of 1123-1373 K. The course of the reaction was monitored by a combination of sample weight loss measurements, product gas analysis, and chemical analysis of the reaction product. It was found that the cassiterite could be best reduced by a combination? of high temperature, reasonably high charcoal proportions, high charge poroslty, and the addition of a small percentage of lime. Analysis of kinetic data obtained from isothermal experiments using theory from the oxidation of carbon by carbon dioxide gave an activation energy value of 255 lci/mole for the consumption of carbon by reaction with cassiterite.

Jan 1, 1990

By P. S. Dunn, A. D. Rollett, H. D. Lewis

"The results of preliminary work on the modeling and measurement of the heat transfer coefficients of metal/mold interfaces is reported. The system investigated is the casting of uranium in graphite molds. The motivation for the work is primarily to improve the accuracy of process modeling of prototype mold designs at the Los Alamos Foundry. The evolution in design of a suitable mold for unidirectional solidification is described, illustrating the value of simulating mold designs prior to use. Experiment indicated a heat transfer coefficient of 2 kW/m /K both with and without superheat. It was possible to distinguish between solidification due to the mold and that due to radiative heat loss. This permitted an experimental estimate of the emissivity, ~ = 0.2, of the solidified metal.IntroductionA feature that distinguishes casting processes from welding processes is the presence of an interface with a low heat transfer coefficient between the mold and the casting. Especially when chill casting, the interface delays the start of solidification and increases freezing times significantly. By comparison welds can be assumed to have a very high heat transfer coefficient. The heat transfer coefficient controls such phenomena as folds and laps on the surface of castings which can be crucial to the acceptability of a casting. The time delay for the start of solidification influences the occurrence of cold shut defects. The standard mold material for uranium casting is high quality graphite which is an excellent refractory when used in vacuum and coated with a refractory wash. Graphite is an effective chill material and has a thermal diffusivity approximately twice that of uranium. Experience has shown that practicable superheat without mold pre-heat is not sufficient for avoiding cold shut defects when casting in graphite molds.TheoryIt is possible to calculate the position of the freeze front s, as a function of time, t, the superheat and interface heat transfer coefficient, h, [1]. However, the value of h cannot be obtained explicitly. The Virtual Adjunct Method (VAM) [2] offers a method for extending the standard equation for an insulating mold where s is proportional to the square root of time. By considering the effect of the interface to be equivalent to finite thicknesses of mold and metal, the following quadratic equation is obtained,"

Jan 1, 1986

By Wayne C. Stewart

Freezing of high pressure air lines and pneumatic equipment has been a recurring problem in the Thompson Smelter. The particular severity during the winter of 1989-90 resulted in costly process disruptions and repairs. A process improvement team with representatives from operations, engineering and both maintenance supervision and the shop floor was established to develop solutions. Their mandate included process evaluation, design, equipment and in-plant commissioning. In 1990, upon recommendation of the team, we installed three Refrigerant/Desiccant air dryers with a total capacity of 20,000 S.C.F.M. to service the Smelter. This paper discusses processes and process improvements associated with this installation.

Jan 1, 1993

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By Juan Ruiz-Ornelas, Yousef Mohassab, Ricardo Morales-Estrella, Hong Yong Sohn, Noemi Ortiz-Lara

The effect of mechanical activation on the reduction kinetics of magnetite concentrate by hydrogen was studied. The magnetite concentrate was milled for 8 h using a planetary mill. After the milling process, the average particle size was reduced from 14 to 4.4 m resulting in a lattice microstrain of 0.30. Thermogravimetric experiments were conducted to focus on the chemical reaction as the rate controlling factor by eliminating external mass transfer effects and using a thin layer of particles to remove interstitial diffusion resistance. The onset temperature of reduction was decreased due to the mechanical activation, and the degree of conversion was decreased by sintering of particles which was confirmed by SEM analyses. In view of the results, a reaction rate expression is discussed from which the activation energy is calculated.

Jan 1, 2016

By Halvor Dalaker, Pål Tetlie

The decomposition of methane has been studied experimentally in contact with various oxides at elevated temperatures. For each oxide, the temperature at which the cracking starts has been determined. No correlation was found to exist between the temperature for the onset of cracking for a given oxide and the affinity for carbon of the oxide's metallic component. In terms of potential for using methane as a reducing agent, calculations are presented that indicate that the suitability of an oxide for such reduction depends on the desired methane+oxide reaction being more energetically favourable than the methane+methane=ethylene/acetylene reactions.

Jan 1, 2014

By Ryszard Prajsnar

During copper production in shaft and flash smelting processes at KGHM Polska Miedz S.A., lead bearing material of sulfide, sulfate, and oxide character is generated in forms such as slime from shaft furnace gas handling systems, converter dusts, and dusts from an electric furnace for copper removal from flash smelting slag. These materials are polymetallic concentrates of Pb, Zn, and Cu, with As, Cl, and Cd as impurities. Shaft furnace slime, containing. about 50% PbS and 15% bituminous substances, is the main lead-bearing material. At the Glogów copper mill, a new plant was commissioned in June 2001 to process 80,000 tonnes per year of lead bearing materials to produce 26,000 tonnes per year of crude lead. The plant consists of a feed conditioning system, three (3) rotary rocking furnaces with a capacity of sixteen (16) tonnes of lead feed fired with natural gas and oxygen-enriched air containing up to 45 vol% O2, and a gas handling system. The gas handling system includes a post-combustion chamber, a gas cooling chamber with Cl neutralization, gas mixing chamber, bag filter, and dry limestone scrubbing system for SO2 removal. The lead-bearing feed is smelted with five (5) wt% Na2CO3 and thirteen (13) wt% iron scrap at a temperature of 950 to 1050°C for three (3) hours. The smelting process consists of four (4) stages; feed drying, firing of gaseous hydrocarbons and solid coal from the feed, lead reduction from slag, and separation of molten products. The flow rates of natural gas and oxygen to the burners are controlled to ensure combustion of the bituminous material in the furnace. The process produces crude lead bullion containing (wt%) 0.1 to 0.5% Cu, 0.02 to 0.5% As, 0.05 to 0.07% Bi, 0.1 to 0.5% Sb, and 0.1 to 0.6%Sn. The process also produces a mixture of sodium silicate slag, Fe-Zn-Pb-Cu-S matte, and Fe-As speiss containing (wt%) 5 to 10% Pb, 2 to 6% Cu, 10 to 15% Zn, 1 to 3% As, 10 to 15% S, 0.5 to 3.0% Cl, 2 to 4% K, 4 to 7% Na, 20 to 30% Fe, and 5 to 10% SiO2. The dust is made up of PbO, ZnO, PbSO4, and PbCI2, KCI, and NaCI with a chemical composition (wt%) of 35 to 50% Pb, 5 to 15% Zn, 3 to 6% As, 4 to 8% Cl, 2 to 5% K, and 2 to 5% Na. The construction of the new lead production plant at the Glogów copper mill will process both current lead-bearing materials as well as lead-bearing material that have been stockpiled over the last fifteen (15) years to give a significant improvement in protection of the natural environment.

Jan 1, 2002

By Saskia Duyvesteyn

Small ion-exchange resin particles provide faster mass transport than conventional-sized beads. Unfortunately, high pressures are needed to pump solutions through columns containing small resin particles. It is preferable to disperse fine resins in the solution being treated. Screens have been used to separate the resin from the solution, but screens do not retain fines created by attrition of the resin particles. We have developed a separation process based on flotation, which relies on the surface characteristics of the resin, instead of size. The resin is conditioned with a surfactant before dispersing it in the solution to be treated; this increases the hydrophobicity of the resin sufficiently for froth flotation, without introducing surfactant directly into the solution. The surfactant adsorbed on the resin surface does not appear to impair the kinetics of metal ion removal. A flowsheet for an effluent treatment process is proposed; other applications are clearly possible.

Jan 1, 1998

By Marcelo B. Mourão

An experimental investigation was carried out to -study the rates of reduction of pellets containing iron oxides by carbon dissolved in liquid iron, at temperatures ranging from 1720 K to 1973 K. Several different pellet types were employed; the materials used in the pellet's manufacture were pure hematite, two kinds of commercial iron ores, and mixtures hematite/silica and hematite/lime: Reaction times were determined employing the constant volume pressure increase technique (CVPI). It has been observed that the reaction rate increases as the temperature and the pellet's specific surface area increases. The reaction rate is also affected by the oxide type: pellets made from commercial ores or from mixtures hematite/silica or hematite/lime show reaction rates lower than those made from pure hematite.

Jan 1, 1996

By E. Saez, M. Bellet, T. Coupez, O. Jaouen

"The paper presents a 3D finite element solver for non-steady state fluid flow. The thermomechanical simulation package REM3D® has been initially developed to model Stokes' flow for polymer injection. The mechanical module is based on a Eulerian velocitypressure formulation. The spatial discretization uses P 1+IP1 tetrahedral elements. The front tracking module consists of the resolution of a transport equation, thanks to a space-time discontinuous Galerkin formulation. It includes mesh adaptation, which permits a dynamic refinement at the front, thus controling the numerical diffusion. The same approach is used to solve heat transfer. In this paper, we focus on the specific adaptations done to treat Navier Stokes flow. The treatment of inertia is detailed, as well as the implementation of sliding conditions at mould surface, using conservative normals. Industrial applications are presented.IntroductionThe study of the mould filling stage in casting processes requires the ability to simulate complex non steady-state three-dimensional flows. Most commercial software use the volume of fluid (VOF) method, associated with a Eulerian formulation, see for instance the series of conferences ""Modelling of Casting, Welding and Advanced Solidification Processes"" [1-3]. The VOF method [4] consists in solving the conservation equation dF / dt = 0 for a variable F - the volumic fraction of fluid - whose value is 1 in filled regions and 0 elsewhere. Two fluids are actually considered: the molten alloy and a gas in the empty regions. This method suffers generally from numerical diffusion in the resolution of the free surface tracking equation, which is of pure advective type. The precision of the computation is then strongly dependent on the mesh density. Since the mesh is fixed (Eulerian formulation) this implies that in case of complex flow the user must have a priori a fairly good idea of the flow characteristics in order to capture properly the critical features of the flow. In addition, the method can hardly handle the discontinuity of the material viscosity at the interface. To prevent this difficulty, the viscosity value is smoothed around the interfuce, adding once again some inaccuracy. Since the value F = ½ is supposed to represent the free surface, it results in a smeared fluid surface. An alternative to the fixed mesh methods are the methods in which the mesh covers the fluid domain only, as proposed by Navti and Lewis [5-6], or Gaston and Bellet [7]. Based on updated Lagrangian schemes, they must be associated with an ALE formulation (arbitrary LagrangianEulerian) in order to reduce the number of full remeshing operations."

Jan 1, 2004