Search Documents

By Shenghui Guo, Ying Lei, Hao Niu, Huilong Luo, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the combination of microwave drying (MWD) and heat pump drying (HPD) drying experiments were designed by response surface methodology (RSM) based on central composite design (CCD) using design expert software (Version 7.15), and the process parameters were optimized. The conditions given by software are: the MWD time is 4.6 or 4.4 min; the HPD time is 9.0 or 8.6 min; and the sample mass is 620 or 600 g. Under those conditions the moisture content is 1.0 10-2kg water/kg wet basis, and the effectiveness ratio is 0.70 kg water/kwh. The results of confirmatory experiments conducted under the optimized conditions show the combined drying have superiority of decrease of energy consumption and increase of handling capacity over the single MWD or HPD.1 IntroductionSilica sand is one of a silicate mineral with properties as hard, anti-friction and less reactive, commonly used as raw material for foundry and construction. The silica sand obtained from mineral dressing processes such as scrubbing, magnetic separation and flotation. Its moisture content is approximately 0.08~0.12 kg water/kg wet basis. The most common methods used for drying are solar drying and hot air drying. But these methods have some shortcomings: for example, the solar drying has longer process time due to low energy yield, [1] hot air drying has low-energy efficiency and a lengthy drying time. [2]Microwave is electromagnetic waves with frequency are 300MHz to 300GHz. The outstanding features of microwave heating are rapidity and selectivity. The water specific inductive capacity of 60~78 is much bigger than common materials, the moisture always quickly absorb electromagnetic wave and rapidly transfer to vapors. So, it can significant reduce the drying time. [3] Heat pumps (HPs) are devices for raising the temperature of low grade heat energy to a more useful level using a relatively small amount of high grade energy."

Jan 1, 2011

By Ravi Vancheeswaran

The consolidation of ceramic fiber reinforced metal matrix composites is a key process step in the synthesis of high performance composite systems. A simulation tool has recently been developed for predicting the evolution of the composites internal state microstructural variables (eg. relative density, fiber microbendinglfracture, and chemical reaction layer thickness at the fiber-matrix interface) during the consolidation processing of spray deposited composite mono-tapes. A Generalized Predictive Control (GPC) scheme is used in conjunction with the simula-tion tool to design near optimal process paths that minimize fiber damage and reaction product thickness while simultaneously maximizing the composites relative density. The microstruc-tural evolution depends nonlinearly on the process conditions and therefore the scheme uses a constantly updated linearization of the model to optimize the input process variable vector. A control simulation is presented to illustrate the performance of the design scheme and to assess the feasibility of its use for the achievement of goal state microstructures at the completion of consolidation cycles.

Jan 1, 1996

By T. T. Chen

Canadian Electrolytic Zinc has developed the "cement-stabilization of jarosite residue" Garofix) process to stabilize zinc plant jarosite residues for disposal. The cement-jarosite mixtures cure quickly, have good mechanical strength and low hydraulic permeability; they possess good neutralizing capability and chemical stability. In the jarofix process, Portland cement partly decomposes jarosite to form (SO4MOH)12.nH2O, ferric hydroxide and an alkali sulphate. Approximately 40% of the jarosite reacts in mixtures containing 30% cement. The jarofix product also contains various Ca-Al-Fesilicate-sulphate-hydrate phases and gypsum, which bond the individual particles together imparting mechanical strength and reducing the permeability. Most of the reactions take place in the first few hours of curing. Ammonium jarosite is slightly more reactive than sodium jarosite but releases NH3 gas; water-soluble Zn in the jarosite residue is stabilized in the cement reaction products.

Jan 1, 1996

By Brian Balmforth

Solvent extraction has been applied successfully to the recovery of a range of metals from a variety of process streams. Particular benefits are derived from the use of new highly selective extractants. These will be exemplified by case studies including the recovery of zinc from sulfate and chloride media using ZENECA's new extractants which show a very high selectivity over iron and the recovery of antimony and bismuth from copper refinery electrolytes using ZENECA's strong and selective extractant DS5834. The conclusions are drawn that solvent extraction is a cost effective technology for metal recovery and recycling, even when used to treat relatively small volume/low concentration process streams, and that it can provide the essential enabling components of a larger system for waste minimisation programmes.

Jan 1, 1996

By Hylton McWhinney, Doanh Tran, Jewel Andrew Gomes, George Irwin, Sameer Pallavkar, Md Islam, David Cocke, Mohammad Rafiqul Islam

"High-performance nickel-based nanocrystalline zinc oxide adsorbents have been prepared adjusting Ni/Zn mol ratio of 1 :5 by thermal decomposition, coprecipitation and sol-gel method for selective adsorption of thiophene in liquid hydrocarbon fuels at ambient temperature and pressure. To understand the nature of reactive adsorption of thiophene (C4H4S) on Ni/ZnO, the effect of preparation techniques, morphological and textural structure on the desulfurization activity was investigated. A model fuel (20 mL) consisting of pentane (C5H12) and thiophene was prepared and adsorption experiments were performed by a batch method under ambient conditions. The physicochemical behaviors of the fresh adsorbents were obtained using X-ray diffraction (XRD) with EDAX, scanning electron microscopy (SEM). The sulfur concentration in the mixture was monitored by UV-vis spectrophotometry. The adsorption reaction confirmed that ZnO played a crucial role in taking up S element to convert it into ZnS. The deposition of nickel on ZnO is an innovative approach which takes advantage of the selectivity of Ni towards S-species and the high adsorptive capacity of ZnO support.IntroductionLow temperature deep desulfurization of fuels via selective adsorption of sulfur compounds keeping coexisting aromatic hydrocarbons and olefins intact is receiving increasing attention in the research community worldwide in order to satisfy the upcoming environmental regulations and fuel specifications. The sulfur compounds in the transportation fuels is a matter of concern when global crude oil slate is becoming heavier and sourer and environmental restrictions on both the refining process and the refined products are becoming more stringent. According to the current refinery technologies, the sulfur content in refinery fuel is typically around 300-500 ppm by weight (ppmw) [1-3]. Starting in 2006, sulfur limits in highway diesel and gasoline were set to 15 ppm and 30 ppm, respectively. During combustion sulfur in the fuel are converted to toxic sulfur oxide (SOx) and contributes to air pollution and acid rains [ 4]."

Jan 1, 2011

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By M. D. Strachan

Technical & Procurement Services Limited (TECHPRO) in Ashford, Kent, UK, have been appointed as Project Managers for the major rehabilitation of the Copper Smelting complex of Nkana Division, Zambia Consolidated Copper Mines Limited, (ZCCM) Zambia. In outline, the overall scope covers three main areas: a) Transfer and implementation of new technology into Zambia for the production of primary copper. b) Replacement of gas collection and gas treatment circuits to guarantee high quality feed to the acid plants. c) Completion of a number of minor projects in the copper smelter and associated utility plants to complement changes in the primary smelting technique. This paper describes the Project Management methodology and style used by TECHPRO to tackle typical problems that arise in retrofit projects of this type. Reference is made specific aspects of the smelter projects to illustrate solutions to the problems. The subjects. addressed highlight the complexities not only of having a -Client 5,000 miles from the Project Office, but also the difficulty of co-ordinating and controlling the performance of min sub-contractors who are also geographically distant.

Jan 1, 1991

By John J. J. Chen, Barry J. Welch

"As in many industrial processes, the detailed mechanisms involved must first be understood before being able to redesign, or to carry out improvements or optimisation of the process and equipment performance. In a great majority of metallurgical processes, visual observation and actual measurement of process variables are either very difficult or near impossible. Often, the cost and effort involved are prohibitive. Consequently, physical modelling is often used to provide some understanding of the process and for the validation of computer numerical models. In this paper, we summarise some of the work carried out at The University of Auckland on the modelling of the Hall-Héroult electrolytic cell, the in-line melt treatment process, and the steel casting tundish. IntroductionIn any industrial process, it is essential to understand the underlying mechanisms before any optimization or process improvement can be carried out. In many metallurgical operations, the processes are conducted at elevated temperature and under rather hostile environments. Consequently, it is often difficult, and sometimes impossible, to observe the actual processes occurring, or conduct measurements which are pertinent. In some situations, it is possible to formulate mathematical equations purported to describe the process, and obtain the solutions numerically. However, in this latter case, the validity of the simplifying assumptions made are often uncertain. Physical modelling may provide the necessary information for the validation of such numerical models. Furthermore, through an application of the principle of similitude, it is possible to apply data obtained from physical modelling to actual metallurgical processes. This paper will summarise some the work carried out at The University of Auckland on the physical modelling of gas-induced flow in the Hall-Héroult electrolytic cell, an in-line melt treatment unit, and the flow in a steel casting tundish.Gas-Induced Flows in a Hall-Héroult CellIn an aluminium cell, the effects due to electro-magnetic forces have been addressed and various design modifications such as magnetic shielding and the positioning of risers have been carried out to control or lninimise the effects of magnetic fields'. Consequently, the effects of gas-induced flows are now becoming significant providing the impetus for the study of the gas behaviour in the bath. Furthermore, the shape and size, and the rate of evacuation of the anodically generated gases affect the cell voltage affecting the energy efficiency; at the same time, the back-reaction between the anode gas and the metal produced is the predominant cause of the loss of current efficiency. Figure 1 shows a cross-section of a conventional cell in which the gas evolution occurs directly under the anodes, and the gas induced flow is confined mainly to the region occupied by the bath"

Jan 1, 1994

By Stephen Chryssoulis, Stamen Dimov

Detection and quantification of precious metals (Au, Pd, Pt, and Rh) in spinels and silicate minerals is important for establishing the maximum attainable recovery by sulphide flotation. To achieve this goal subpart per billion (ppb) detection limits are required plus the ability to quantify results. Existing quantitative microbeam techniques (EPMA, PIXE, SIMS, TOFLIMS) have limits of detection in the O. l-200ppm range. Time-of-flight resonance ionization mass spectrometry (TOF-RIMS) is a microbeam analytical technique that allows for the identification and quantification of atomic species in very small quantities. It utilizes a tunable laser source for resonant excitation and ionization of a particular element of interest and has some unique features: elemental selectivity, linear response over a large dynamic range and very high sensitivity. The analysis consist of three steps: (i) the solid sample is vaporized by laser ablation to form a plume containing neutral atoms, (ii) the neutral atoms of a specific atomic element in the plume are resonantly excited and ionized by another tunable laser, and finally (iii) the ions created are mass analyzed in a time-of-flight mass spectrometer. A TOF-RIMS mass spectrometer was developed at AMTEL for trace element analysis of Au, Pd, and Rh in minerals. The spectrometer was calibrated using homogeneous CANMET and NIST reference samples covering three orders of magnitude in concentration. Attained minimum detection limits (MDL=2cr of the background) are in the low ppb range.

Jan 1, 1999

By G. Van Weert

The pellet reactor was developed approximately 20 years ago in the Netherlands for softening drinking water. Since then, some 35 plants have been built, ranging in capacity up to 8500 m3/h. Applications now also include removal of phosphates and fluorides and the production of metal carbonates and sulphides from waste streams. The pellet reactor consists of a fluidized bed, wherein the process solution is thoroughly mixed with the precipitation reagent at special inlet nozzles to give over-saturation of the compound to be precipitated. In water softening applications, the compound is CaCO,. In the case of nickel or other metal waste streams, Na2CO3 solution is added in sufficient amounts to precipitate metal (hydroxy) carbonate on the fluid bed particles. These grow typically to dense spheroids, which are removed when they reach 0.8 to 1.0 mm diameter. These spheroids are easily dewatered, free flowing and low dusting. The latter property is becoming an attractive advantage in connection with new plant hygiene regulations. The operation of a 60 cm diameter pellet reactor on nickel containing plating waste is described and the properties of the produced nickel carbonate spheroids are discussed.

Jan 1, 1993

By B. G. Thomas

"Mathematical process models can be applied in several different ways to serve industry by inducing beneficial changes to process operation. This paper attempts to summarize the different uses, types, and attributes of these models, and to offer some ideas to consider when developing, using, and reporting on them. Process models range from empirical to mechanistic in nature and vary in complexity from simple analytical solutions to coupled, 3-D transient numerical simulations. They are classified here according to the way in which they are implemented in practice, viz. fully-online models, semi-online models, off-line models, and literature models. The purpose of the model should dictate how choices are made during its development. Ways to validate and compare the model with experiments are suggested. Examples are taken in the context of the author's experience in modeling the continuous casting of steel.IntroductionThe objective of this paper is to provide a partial introduction for this symposium by discussing some basic aspects of the application of mathematical process models in industry. Essentially, the aim is to explore how process models are used to benefit industry, and to offer some general comments and suggestions, based on the experience of the author, on how models can best meet this goal.This work is concerned with process models, which consist of systems of mathematical equations and constants that are solved on a computer to make quantitative predictions about some aspect(s) of the process. The specific variables required as input data and generated as output data are important features of the model. The equations often derive from a numerical solution to one or more differential equations and their boundary conditions. The model also includes the constants, which represent material properties, empirical relationships, and other knowledge about the process, and usually require considerable effort to obtain. Thus, general purpose commercial software packages, (ie. finite-element or finite-difference based codes), are not models in this context. They are useful tools, however, serving as frameworks for the development of process models."

Jan 1, 1994

By Andrew Campbell, Michael Reed

"WorleyParsons has used Discrete Event Simulation methods in conjunction with more traditional process models to assess the performance of copper smelting operations. This work was performed to determine the plant capacities and suitability of proposed debottlenecking options including accounting for the planned and unplanned (breakdowns) shutdowns in the various parts of the plant and supply chain. This paper outlines the methods used along with demonstrating the benefits of selecting a feasible option and minimizing capital and operating costs.IntroductionTraditionally for de bottlenecking studies of smelters and other process plants, a mass balance is performed based on continuous operating rates and expected operating hours. Smelters have several points of failure that will restrict, if not take the entire plant offline. By using a more detailed model, validated against plant experience, bottlenecks can be demonstrated and strategies to remove them to increase plant availability and economic.The modeling simulates the plant performance in real time, and by performing enough simulation the expected long run performance of the plant can be estimated. The models have been built using ExtendSim which is a powerful Discrete Event Simulation software package that is ideally suited to the batch and semi-batch processes and events that occur within smelter operating environments. The value of performing this work is that the operational performance of the plant can be assessed ensuring production targets are met, without using excessive capital outlay."

Jan 1, 2013

By A. A. Hejja

The effect of composition on electrical conductivity, viscosity and liquidus temperature of the slags was investigated in the temperature range of 1300" to 1450°C. The synthetic slags containing CaO, MgO, SiO,, A1,0, and FeO were similar to those employed in the electric furnace smelting of sulphide Cu-Ni concentrates containing PGM (Platinum Group Metals) from the Merensky Reef of South Africa. FeO and SiO, were found to affect the viscosity and conductivity the most while liquidus temperature depended on MgO content in addition to these. The activation energy for electrical conduction was found to vary from 67 to 159 kJ/mol and that for viscosity from 125 to 209 kJ/mol. Optimization of the slag composition was attempted on the basis of opposite trend of the viscosity-electrical conductivity relationship with slag composition.

Jan 1, 1994

By Stig Petersson

Slag from the converting of copper matte is usually recirculated to the smelting furnace. This recirculation generally causes disadvantages as magnetite-build-up in the furnace, accumalation of impurities as antimony, lead, nickel etc in the process. The treatment of converter slag in a separate furnace in order to recover the copper and nickel content would be of advantage from several points of view. At the Mining and Metals Division, Boliden, testwork has been carried out to treat converter slag from the PS-converters in a separate furnace. The tests have been performed in laboratory and pilot plant scale. The pilot plant tests have been carried out in a TBRC with charges of 5 tons. Based on these tests a full scale TBRC has been projected in order to treat the slag from the PS-converters. This slag will be reduced with copper concentrates to give a matte and a final slag low in copper and nickel. The background and data from the testwork are presented. Also the lay out, technical data and flowsheets for the projected process are shown as well as some production data from the Rönnskär smelter.

Jan 1, 1976

By Jerry L. Smith

Industry on a whole has not been very receptive to government prodding to implement waste minimization programs. Waste minimization has the appearance of substantial benefits, however, there are underlying difficulties and suspicions that need to be addressed before industry will support pollution prevention initiatives. They can be summarized as follows: - Human behavior resists change, uncertainty, and unknowns. - New waste minimization techniques are difficult to find and research. - Calculating the true cost of present waste practices as well as new techniques being considered is difficult and time consuming. - Getting a consensus opinion of all the individuals affected on the course or technique to be employed in a pollution prevention program. New software products have addressed many of the problems associated with implementing pollution prevention programs: They contain research on a large number of pollution prevention techniques and case studies; they generally are accessed by EPA ID number, chemical name, or synonym; and some programs have the option to print a comprehensive written user-specific pollution prevention program.

Jan 1, 1994

By Thomas R. Wildeman

Experimental methods for studying vapors over solid minerals are reviewed and an especially developed method using atomic absorption is described. The method is used to study vapor pressures over Te. Ag, Au, Ag2Te, and AuTe2 from 250°C through 10S0oe. Vapor pressures observed and, concurrently. sintering properties are significantly altered by the form of the solid. The vapor pressures of the tellurium compounds reveal complex processes occurring on the surfaces of the solids. The data given also point out a method of recovering precious metals from their telluride minerals w

Jan 1, 1987

By V. V. Satya Prasad, A. Sambasiva Rao

Electroslag melting technologies have recently been developed for recycling light scrap of valuable metals and alloys such as superalloys and oxygen free high conductivity (OFHC) copper at Defence Metallurgical Research Laboratory (DMRL), Hyderabad. Conventionally, electroslag melting processes use consumable electrodes. Because of the difficulty in compaction of scrap into a consumable electrode of satisfactory quality, non-consumable electrodes such as graphite and water-cooled copper have been designed. Electroslag remelting using a water-cooled non-consumable electrode was developed to melt scrap of a nickel base superalloy. Sound ingots with smooth surface finish and properties comparable to vacuum melted superalloys could. be obtained from scrap using this process. A modified electroslag crucible melting process using graphite crucible and graphite electrode was developed for recycling OFHC copper scrap. Copper ingots with less than 10 ppm oxygen and electrical conductivity"" 100% IACS could be produced. The same process was also utilized to produce copper-based alloys such as copper-chromium and copper-titanium starting from copper scrap.

Jan 1, 2000

By Milorad Cirkovic

Kinetics of copper concentrate oxidation in roasting processes in a fluidized bed reactor has been studied at temperatures between 600°C and 720°C using particles of 0.038 to 2.5 mm in average size. The analysis of composition of samples has been done by chemical methods. Phase composition has been determined by Siemens X-ray equipment with Cu anticathode and Ni filters at a voltage of 40 kV and a current of 18 mA. The content of sulphur has decreased from 33.23 to 19.02 mass percent with the increase of temperature, but the content of Fe304 has increased from 0.15 to 17.14 mass percent. The new mechanism of copper concentrate oxidation in a fluidized bed reactor is proposed in this study. It has been shown from the mathematical model that the velocity of oxidation of copper concentrate between 600°C and 720°C is virtually controlled by the rate of diffusion of 02 through the layer of reaction product.

Jan 1, 1999

By Wenxian Zhu, Patrick R. Taylor

"The small dimensions of nano-sized materials leads to novel and enhanced mechanical and physical properties. A thermal plasma reactor has been developed to study the formation of nanometer sized metal powders. A supersonic nozzle and a powder filter were designed and built. By vaporizing coarse metal powders in the plasma flame, and quenching the metal vapors through the nozzle at the rate of 107 K/sec, nanometric sized powders have been produced. The powders were collected in an airtight secondary quench-filter system. The particle size of the product power is 5 -20 nanometers, obtained through TEM analysis. The XRD analysis showed that the powder did not oxidize after the filter was handled in an inert atmosphere glove box.IntroductionNanostructured materials have been shown to exhibit improved physical and mechanical properties compared to conventional materials with larger grain sizes (1,2). There have been several methods proposed for preparing nanometer size materials. Thermally induced vapor-phase reactions have been used to produce a variety of powders. A common feature of these processes is the rapid production and cooling of condensable reaction intermediates and products, by gas-phase reactions, leading to the formation of a large number of very small particles. Thermal plasma synthesis of ultra-fine size particles has been attracting increasing interest (3,4,9-11), because it offers many advantages, especially in refractory materials processing, compared to conventional processes: (a) thermal plasma temperatures are very high(> 5000 K); (b) the rates of chemical reaction are much faster than those encountered in conventional processes; (c) high-purity materials may be obtained using fewer processing steps by collecting the product at temperatures where the by-products are in the vapor phase; ( d) the mean particle diameter can be controlled; (e) unifom sized particles may be produced with clean surfaces (these particles are particularly suitable for pressureless sintering); and, (f) high throughput per reactor volume can be achieved. In addition, the process used for generating particles determines the degree of sintering ability of the powders, since the process dictates the morphologies, the purity and its size distribution. In the future, thermal plasma synthesis nanometer size particles may play an important role in vapor phase reaction techniques and might be expected to be one of the first full scale commercial installations in the future."

Jan 1, 1998