Search Documents

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

By Meghan McGrath

Third generation advance high strength steels with microstructures of acicular ferrite and retained austenite were investigated and meet mechanical property goals. A good combination of strength and ductility were achieved with duplex ferrite and austenite microstructures where cementite formation was suppressed. Transformation induced plasticity (TRIP) behavior produced rapid work hardening. The mechanical properties of two hot-rolled steels with duplex microstructures were compared and had the following compositions: (1) Fe-0.14C-13.87Mn-1.42Si-3.51Al; and (2) Fe-0.06C-14.2Mn-1.85Si-2.38Al. These steels were cast, homogenized, and hot rolled at 900ºC to obtain a refined microstructure with ultimate tensile strengths and elongations to failure of 865 MPa and 39% and 1,217 MPa and 28%, respectively. The amount of metastable austenite in both compositions decreased after tensile testing from 58% and 28% to 6% and 0%, respectively. Microstructures were characterized using optical microscopy, scanning electron microscopy (SEM), and x-ray diffraction.

Jan 1, 2010

By Tammy G. R. Portela

A comparative characterization of the dimensional and mechanical properties as well as structural aspects of two different types of fibers extracted from the leaves and petioles of the buriti palm tree was performed. A statistical analysis revealed that both types of fibers present a significant dispersion in length and equivalent diameter. However, the corresponding intervals of dimensional variation are sensibly different. The tensile properties showed that both types of fibers display a tendency of higher strength for smaller diameters. Moreover, the fibers extracted from the leaves depict a comparatively lower strength. By contrast, the fibers from the petiole present an average strength sufficiently high for the use as reinforcement of polymeric composites. The structural aspects of tensile-rupture fibers, characterized by scanning electron microscopy, showed marked distinction in the microstructure and fiber behavior of both types of investigated fibers. This could explain the differences in mechanical behavior

Jan 1, 2010

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By Yue-yuan Li

China has abundant magnesite resource, but the low-grade and powder ores have always been rejected, which influences the comprehensive utilization of resource and often causes circumstance problems. The present work investigated the preparation of magnesia whisker using magnesite tailings as starting materials by preparation magnesium carbonate whisker as precursor firstly in the route of calcination, hydration, carbonation and pyrolysis, follows by second calcination of the precursor. The influence of pyrolysis conditions and additives on morphology of magnesium carbonate crystal as well as the influence of calcination conditions on morphology of magnesia whisker was investigated. The results showed that thermal decomposition products was MgCO3?3H2O. Magnesium carbonate whisker with length of 10~60 µm and the length-to-diameter ratio of 10~20 was prepared when soluble magnesium salt was added. While temperature was elevated at 1°C?min-1, magnesia whisker with length of 10~60µm was obtained.

Jan 1, 2010

By Yuanbo Zhang, Guanghui Li, Zhenyu Fan, Tao Jiang, Xiaohui Fan

"Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60% of the total. Aiming at the features of sintering flue gases and existing problems during the flue gas desulphurization, a technical route of flue gas circulation sintering (FGCS) for iron ores has been put forward. Under the simulated experimental conditions, effects of FGCS process on the main output and quality indexes and SO2 emission rule are researched using simulating flue gases. Compared the novel FGCS with conventional sintering process, SO2 in the final sintering flue gas is obviously enriched and the total exhaust gases can be reduced evidently. The decreasing of oxygen content in circulating gases has bad effect on the sintering indexes. Increasing the oxygen potential is beneficial to obtain high quality sinters. This investigation shows that the FGCS process is promising.IntroductionSteel is a kind of essential material for modern society, but steel-making process is characterized by high energy-consumption and emission as well as heavy environmental pollution. Chinese steel industry has developed rapidly in the last decade, and the environmental problem caused by ironmaking and steelmaking have also aroused the greatest concern, especially the atmospheric pollution caused by SO2, CO2, etc. Iron ore sintering process is the main source of SO2 generated in the steel industry, of which the discharge amount of SO2 emission accounts for about 60 % of the total. The development of the desulfurization process for sintering flue gases to reduce SO2 emission in sintering process is not only the requirements of sustainable development but also the most important environmental tasks for steel industry [1-5]."

Jan 1, 2011

By Wolfgang Van Hooff

Encouraged by a strongly growing and evolving market for granulated products, Paul Wurth continuously improves its granulation and dewatering technologies to provide customers with state of the art installations. Continuously developed know-how about the granulation process of iron blast furnace slag enabled application to non-ferrous materials such as Ni-Slag, Pb-Slag, Blister Copper, Cu-Matte and even TiO2-Slag, which rank among the most difficult materials to granulate. This paper identifies how critical objectives in granulation and dewatering technologies applied to different molten materials with respect to various product quality objectives can be addressed. The differences between hot and cold water granulation systems are explained, including the step from cold runner to granulation water tank. Development of a flow and pressure controlled blowing box is the latest step to optimize the granulation process in order to meet the latest standards in terms of quality, power consumption and environmental protection.

Jan 1, 2006

By Hebi Yin

A coupled cellular automaton (CA) - finite element (FE) model was developed to calculate the growth of dendrites during the solidification of cubic and hexagonal metals. The model solves the conservation equations of mass, energy and solutes in order to calculate the temperature field, solute concentration and the growth morphology of dendrites, including the grain structure and the dendritic microstructure. Validation of the model was performed by comparing the simulation results with calculation results from previously published works, showing qualitatively good agreement in the dendritic morphology. Application to magnesium alloy AZ91 illustrates the difficulty of modeling dendrite growth in hexagonal systems, observed as deviations in growth direction caused by mesh-induced anisotropy. The model was applied to the simulation of small specimens with single- and multiple- equiaxed grain growths and columnar grain growth in directional solidification. The influence of cooling rate and some kinetics parameters on the grain morphology are also discussed.

Jan 1, 2009

By J. R. Donald

Electric arc furnace (EAF) dust, which can be considered as a by-product of the steel recycling process, contains significant quantities of recoverable zinc and iron, as well as hazardous elements such as cadmium, lead and chromium, which can be leached by ground water. The zinc in the EAF dust is found almost entirely in the form of either zinc oxide or zinc ferrite, the latter accounting for 20 to 50 percent of the total zinc. It is important that an efficient process be developed which renders the dust inert, while reclaiming the valuable metals to off-set processing costs. During the conventional carbothermic reduction processes, iron is formed, and this iron can participate in the reduction of the zinc oxide in zinc ferrite. In the present work, the reduction of the zinc oxide in zinc ferrite by iron according to the following reaction: ZnO-Fe2O3(s,s) + 2 Fe(s) = Zn(g) + 4 FeO(s) was studied in an argon atmosphere using a thennogravimetric technique. First, a thermodynamic analysis was performed using the F*A*C*T computational system. Then, the effects of briquette aspect ratio (lid), temperature, zinc ferrite particle size, amount of iron added, as well as additions such as lime, sodium chloride, and calcium fluoride were investigated. It was found that, initially, the reaction was chemically controlled with an activation energy of 178.1 kJ/mol. Then, after a product layer had formed on the outer surface of the briquette, the reaction was restricted by the diffusion of zinc gas away from the reaction interface. The parabolic rate law was fitted to the experimental data, and the parabolic rate constant was found to be: = -6.2275 + 0.0054 T (K)

Jan 1, 1995

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Pengfu Tan

Electric arc furnace (EAF) dust from the steel industries is listed by the United Sates EPA as a hazardous waste under the regulations of the Resource Conservation and Recovery Act due to the presence of lead, cadmium and chromium. The disposal of the approximately 650,000 tons of EAF dust per year in the U.S. and Canada is an expensive and unresolved problem for the majority of steel companies. The Waelz process has been considered as the best process for treating EAF dust. A process model, combined thermodynamic modeling with heat transfer calculations, has been developed to simulate the chemical reactions, mass and heat transfer and heat balance in the kiln. The injection of air into the slag and the temperature profile along the kiln has been modeled. The effect of (CaO+MgO)/SiO2 on the solidus temperature of slag has been modeled also and discussed. Some optimizing results have been presented in this paper.

Jan 1, 2005

By Hamed Mirzadeh

The hot working behavior of 17-4 PH stainless steel was studied using the hot compression test at temperatures of 950-1150 °C with strain rates of 0.001-10 s-1. A step by step procedure for data analysis in hot compression test was given. The work hardening rate versus stress curves were used to reveal whether or not dynamic recrystallization (DRX) occurred. At low Zener- Hollomon (Z) parameter, this material showed a new DRX flow behavior, which was called Multiple Transient Steady State (MTSS). At high Z, as a result of adiabatic deformation heating, a drop in flow stress was observed. The general constitutive equations were used to determine the hot working constants of this material. Moreover, after a critical discussion, the deformation activation energy of 17-4 PH stainless steel was determined as 337 kJ/mol.

Jan 1, 2010

By Sutham Niyomwas

Silicon-Silicon Carbide (Si-SiC) composites were synthesized by self-propagating high temperature synthesis (SHS) from a powder mixture of SiO2-C-Mg. The reaction was carried out in a SHS reactor under static argon gas at a pressure of 0.5 MPa. The standard Gibbs energy minimization method was used to calculate the equilibrium composition of the reacting species. The effects of silica sources and carbon mole ratio in precursor mixture on the Si-SiC conversion were investigated using X-ray diffraction and scanning electron microscope technique. The as-synthesized products of Si-SiC-MgO powders were leached with 0.1M HCl acid solution to obtain the Si-SiC composite powders.

Jan 1, 2009

By Guan-zhou Qiu, Shui-shi Liu, Yu-feng Guo, Tao Jiang

"The preparation of high-quality synthetic ruitle from electric furnace titanium slag was systematically investigated by activation roasting followed by acid leaching process. The results showed that impurities such as Ca and Mg in titanium slag can be effectively removed and TiO2 grade of the product was markedly improved by the process. High-quality synthetic rutile containing 88.54% TiO2, 0.42% (CaO+MgO) was obtained under the conditions that roasted with 7.5%(wt) H3PO4 at 1000 oC for 2h, followed by two-stage leaching in boiling dilute sulfuric acid for 2h. Mechanism studies showed that anosovite solid solution and silicate minerals were reacted with phosphoric acid in the roasting process. As a result, titanium components in titanium slag turned into rutile (TiO2) and impurities were transformed into acid-soluble phosphate and quartz.IntroductionWith the gradual depletion of natural rutile and the rapid development of titanium industry in China, the natural rutile reserves cannot satisfy the requirement for production of titanium pigment and titanium sponge. Ilmenite is, therefore, becoming main raw material for titanium industry. However, because of its low TiO2 grade, it generally requires preconcentration to titanium-rich material such as titanium slag or synthetic rutile [1-3].Ilmenite resources are extremely rich in Pan-xi area of China, which account for 90.54% of total ilmenite reserves in China [4]. The titanium slag produced by electric smelting of ilmenite concentrate has high contents of Ca and Mg, and is not suitable as a raw material for chloride process and titanium sponge production. Therefore, upgrading titanium slag to prepare raw material suitable for chloride process and titanium sponge production has important significance for the development of China's titanium industry."

Jan 1, 2011

By Yunyan Wang

Diagrams of pc-pH for the complex ions concentration and pH value and -g- for activity coefficient and ionic strength ln±MnSOI4had been drew based on the thermodynamic principle of coordination chemistry and combined with Pitzer theory at 298.15K. The diagram of -g- indicated that -gincreased sharply from 0.0000 up to 1.2147 when I changed from 0.00 ln±MnSOIln4±MnSO4to 0.09; The increase of -gbecame slowly when I was more than 1.00 and less than 1.69; kept still when I ln±MnSOln4-g±MnSO4was more than 2.25 and less than 4.00. Diagrams of pc-pH illustrated that the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pc increased from 6.5 to 5.5 when I increased from 0.00 to 4.00; The pH of the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pH increased from 11.80 to 12.76 when I increased from 0.00 to 2.89, the pH kept still when I (I was less than 4.0) increased. There is single function relationship between the minimum solubility of Mn(OH)2(s) and relevant pH in different I.

Jan 1, 2010

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By Malti Goel

"Ferrous and non-ferrous metals industries are source of both direct and indirect greenhouse gas (GHG) emissions. Metal industry accounted for 29.7% of the total GHG emitted from the Indian industry sector in 2007. Aluminum is second largest contributor after steel. Indian Aluminum industry has been growing and is adopting several effective measures for better efficiencies through process change and waste utilization. Improvement in the energy efficiency can form the basis of monitoring reduction in emissions. Under the National Action Plan on Climate Change 2008, National Mission for Enhanced Energy Efficiency (NMEEE) aims to upscale the efforts to unlock the market for energy efficiency improvement on a public private partnership (PPP) basis. For a transition to low carbon economy industry is undertaking voluntary measures through scientific and technological innovations both in upstream and downstream sectors. In this paper an attempt is made to overview recent developments in Indian Aluminum industry as well as summarize scientific & technological challenges and prospects.IntroductionAluminum plays a vital role in industrial development. It is a substitute for different type of materials ranging from wood to copper and steel. The aluminum industry has high energy consumption and high contribution to greenhouse gases from carbon dioxide and perfluorocarbons (PFCs) emissions. It is estimated that CO2 equivalent burden of aluminum industry is about 1% of total anthropogenic emissions. The anticipated world growth rate is 3.5% for aluminum demand. Through measures to reduce both direct and indirect CO2 emissions, electricity consumption was reduced from 25 kWh / kg of Aluminum in 1998 to 15 kWh / kg of Aluminum produced in 2008. It is targeted to further reduce it to 10.8 kWh. Aluminum industry is also responsible to about 60% of all PFC emissions. The PFC emissions are harmful to environment, accumulate in surrounding vegetation and contaminate. Efforts to reduce PFC emissions from aluminum industry started early and reduced to 0.5-1 kg / tonne in 1990 [1] from 12-15 kg / tonne in 1940. Since 1990s to 2000 it further reduced to 0.2 -0.4 kg / tonne as seen in Fig. 1. The Global Aluminum Sustainable Development Initiative (GADSI), targets perfluorocarbon (PFC) specific emissions reduction of 80% for 2010 relative to 1990."

Jan 1, 2011

By H. Antrekowitsch

Nowadays, the pyrometallurgical treatment in copper smelters is the common process for the recycling of metals from the electronic scrap. Furthermore the European Directive on the Waste from Electrical and Electronic Equipment (WEEE) and the Directive on the Restriction of Hazardous Substances (RoHS), increase the importance of electronic scrap recycling. Besides these a high amount of plastic and inert components in these materials leads to problems at the processing. An optimisation concerning the internal recovery and the high amount of plastic is necessary to reach the recycling quota of the European directive. The majority of the scrap is treated mechanically in order to separate in a first step plastics from metals, iron from nonferrous metals and harmful substances from valuable materials. But the quality of the different fraction often rather low and further treatment leads to higher costs. Therefore an interaction between mechanical treatment and metallurgical processing should be realised. The Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals at the Institute of Nonferrous Metallurgy at the University of Leoben carried out investigations concerning the optimisation of the metallurgical recycling and the treatment of the input materials especially of printed circuit boards.

Jan 1, 2006

By Jinxing Ji

Several fundamental aspects related to the nickel electrowinning from chloride electrolytes have been addressed in this paper. The thermodynamic study includes the activity coefficient of the hydrogen ion and the speciation diagram of NiCI2 solutions. The activity coefficient of the hydrogen ion (YH+) was calculated and estimated experimentally using a combination glass pH electrode. It was found that YH+ was greater than one in concentrated NiCl2 solutions and increased significantly with increasing NiCl2 concentration. The speciation diagram for NiCl2 solutions was plotted with YH+ and the effect of the ionic strength on the equilibrium constants being taken into account. It was discovered that the predominant nickel species in the acidic region were Ni2+ and NiCI+ in 0.937 M NiCl2 solution at 25°C. Electrodeposition tests demonstrated that higher Nit' concentration in the electrolyte improved the current efficiency of nickel electrodeposition (CENi). The additions of H3BO3, and NH4Cl increased very little the current efficiency of nickel electrodeposition at pH 1.5 and temperature 60°C. However, the addition of sulfate decreased the current efficiency of nickel electrodeposition. Nickel electrodeposition was also found to be a steady-state process since the amount of acid added to the electrolyte at a constant pH increased linearly with time during galvanostatic electrodeposition. The cathode surface pH during nickel electrodeposition was measured using a flat-bottom combination glass pH electrode and a 500-mesh gold gauze as cathode. The cathode surface pH was found always to be higher than the pH in the bulk electrolyte, and if the current density was sufficiently large, it would eventually reach a level causing precipitation of insoluble Ni(OH)2(s) on the cathode surface. Rotating disc electrode studies revealed that the rate of nickel electrodeposition was first order with respect to the activity of nickel ion and zero order with respect to the activities of chloride and hydrogen ions. The rate of hydrogen evolution was found to be first order with respect to the activity of hydrogen ion and to be zero order with respect to the activities of nickel and chloride ions. These findings indicate that nickel deposition and hydrogen evolution proceed independently.

Jan 1, 1995

By C. E. M. Meskers

End-of-life Electronic and Electrical Equipment, o_cially called WEEE, is unjustly regarded as mainly a waste management problem. What is structurally overlooked is the enormous resource impact of these devices. EEE rep- resents a tremendous metal resource, which should be uti- lized through e_ective recycling, which has a much lower environmental footprint than primary production. The actual amount of end-of-life EEE recycled today is embar- rassingly low since insu_cient EEE is collected and part of the collected EEE is exported to developing countries, where it is largely not entering o_cial recycling systems. To achieve a global recycling society issues like technol- ogy, economics, life cycle structure, stakeholder aware- ness and legislation have to be addressed in a global, co-operative manner so that sustainable closed product cycles can be obtained. Requirements for a "global re- cycling society" are de_ned to address today's reality of global ows of used consumer products, taking into ac- count the likely needs of the future.

Jan 1, 2009