Search Documents

By Wei Liu

A new process for extracting cadmium from the electric precipitated dust produced by ISP process was studied. A leaching rate of 89.1% of cadmium was attained by leaching the dust with NH3?H2O-(NH4)2SO4 system under the best leaching conditions: ratio of liquid to solid(l:s)=2.5, c(NH3):c(NH4+)=3:5, total concentration of ammonium and ammonia=8 mol?L-1, leaching time= 1.5h, temperature=35. The most troublesome impurity of lead could be deposited from the leached out solution automatically after put it static more than 15h when the total concentration of zinc and cadmium was up to 45gL-1 , and the final concentration of lead was 0.0047 gL-1, which meant 99% of it was removed. Metallic cadmium which contained cadmium more than 99% was prepared by electrowinning under the conditions: current density=750Am-2, total concentration of Cd2+ and Zn2+>25gL-1. The current efficiency was about 87% and the energy consumption for every ton of cadmium was about 548KWht-1. Main impurities of the metallic cadmium were copper and zinc and all of they could be got rid of in the following pyrometallurgical refining step.

Jan 1, 2006

By Valdeci Paula Alvarenga, Sergio Luiz Costa, Itavahn Alves da Silva, Filipe Bueno Carvalho, Varadarajan Seshadri, Carlos Antonio da Silva

Use of fluorspar in steel refining operations is one of the environmental concerns and as such reduced consumption of this material or substitution of the same is one of the objectives. Industrial runs were carried out at Aperam Steel making convertor unit (Timóteo, MG, Brazil) using recycled/briquetted slag for partial or complete substitution of fluorspar. Samples were collected from the metal bath and slag after oxygen blowing to assess dephosphorization with several combinations of recycled/briquetted slag and fluorspar. The results showed that partial substitution of fluorspar by BOF slag briquettes did not affect the efficiency of dephosphorization. In general average Phosphorus content was reduced to 0.010% in the case of partial substitution compared to 0.016% in the regular refining procedure with no substitution. This replacement also resulted in 40% reduction of the fluorspar consumption in the converter

Jan 1, 2015

By Shuai Wang, Gang-hua Fu, Lu Yang, Yu-feng Guo, Tao Jiang

The fluorine-bearing iron concentrate is one of the refractory raw materials for pelletization, which is mainly used in Baotou iron and steel company with lots of problems, such as narrow roasting temperature range and low compressive strength of products. According to its specific character, the effects of roasting temperature, time on the compressive strength and microstructure of pellets were researched. The results show that low melting substances formed during the roasting was the dominant reason of those problems. High melting substances were added in the roasting to investigate their effects on the roasting properties of fluorine-bearing iron concentrate pellets. Low melting substances were reduced when chromite was added. The compressive strength of products was 3100N/P when the 2% chromite was added at the roasting temperature of 1150 ºC, which was increased 700 N/P compared with the pellets without chromite, and the roasting temperature range was expanded by 170 ºC.

Jan 1, 2016

By Taufiq Hidayat

Accurate description of complex phase equilibria provide the foundations for the improvement of non-ferrous pyrometallurgical smelting and recycling processes. Recent advances in microanalysis and experimental techniques enable accurate phase equilibria characterisation. Quantitative microanalytical techniques including Electron Probe X-ray Microanalysis and Laser Ablation ICP-MS enable the concentrations of major and minor elements present in different phases in samples to be accurately measured providing data that cannot be obtained using bulk chemical analysis techniques. High-temperature equilibration experiments coupled with the subsequent analysis of elementary reactions at micro- and macro-scales ensure the attainment of equilibrium conditions, and therefore, ensure true phase equilibria information is obtained. Examples of the application of the improved methodology on the investigation of phase equilibria of low-order and complex, multi-component gas/slag/matte/metal/solids Cu2O–PbO–ZnO–Al2O3–CaO–MgO– FeO–Fe2O3–SiO2–S systems and the distribution of minor element are provided. The experimental study is closely integrated with thermodynamic database development for the above system. Example of implementation of the research outcomes into industrial operations is demonstrated.

By C. Anderson

Most applications of copper metallurgy are geared towards primary production. However, as recycling of materials is a growing industry, one future facility will rely on copper metallurgy as a means of processing precious metals. This paper will discuss the derivation of the proposed copper pyrometallurgical and electrometallurgical unit operations to be utilized in industrial recycling of secondary precious metals.

Jan 1, 1999

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By A. Mukhopadhyay

Gas stirring, simultaneous arcing, chemical additions are some basic steps in the secondary steel making. From tap to team however, there are enough uncertainties and several in-situ decision making required to match the fmal composition and temperature in the given amount of processing time. Currently available control algorithms rely on overall material and heat balance coupled with a self-learning regression based tuning of model constants. In this paper we demonstrate the capabilities of Computational Fluid Dynamics (CFD) in modeling and analyzing the thermo-chemical aspects of secondary Steelmaking. These models take advantage of scientific and engineering advances in computational tools and provide almost real time speed of analysis. This can be a very effective tool for operator training, process debugging and improvement as well as new innovations. Keywords: Argon purging, Secondary steelmaking, Arcing, Ladle Furnace, Process Control.

Jan 1, 2003

By R. T. Seaman

Pressure oxidative treatment of whole ores and/or mineral concentrates is used to leach or liberate metals of value for downstream recovery. Silver, when present, is often lost in processing, precipitating as a cyanide-insoluble jarosite in the residue. Depending on pressure oxidation conditions, the degree of silver loss to jarosite can vary dramatically. Batch bench-scale testwork is often performed to define that loss, and then assess the implications in continuous operations. This paper focusses specifically on the impact of CESL pressure oxidation conditions on silver recovery, and discusses limitations of batch bench-scale testing as well as means of overcoming these limitations to better predict silver recovery in the scale up from bench-scale to continuous operations. Since silver is only partially soluble in both sulphate and chloride media, it will gradually leach and deport to a jarosite as oxidation progresses. When a silver-insoluble anion, for example iodide, is dosed prior to oxidation, there is a marked improvement in silver recovery from batchgenerated residue; however, that benefit is not consistently seen in continuous operations. The difference has been attributed to the dynamic solution conditions in the batch test, specifically the first few moments of oxidation. Using these principles, a predictive correlation has been established between initial leach concentrations of iron and acid and ultimate silver recovery with iodide addition.

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By Zhang Duomo

A novel homogenous precipitation method, including microwave heating, solution conductivity controlling and freeze drying, was developed for the preparation of US nanoparticles. The effects of the precipitation conditions on the structure and morphology of CdS particles were discussed individually. It was found that under the experimental conditions the particle sizes were controllable in the range of 14nm to 100nm. Blend-type CdS was obtained from nitrate or sulphate solution and the more stable wurtzite-type US was obtained from chloride solution, which was ascribed to the coordination of C1 and Cd2+ altering the supersaturation of the solution as well as the different growth units and their connecting patterns, In the precipitation process the surface of US nanoparticles were surface modified with CH3CHSCOOH. The results demonstrate that the bifunctional thiols of thioglycolic acid modified the surface through Cd-S coordination bonding and the induced counter ion AOT-SO3 as the balance charge further increased the stability and dispersity of US nanoparticles. This surface-modified US nanoparticles had been used to prepare nonlinear optics and self-assemble catalysts.

Jan 1, 2003

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By J. D. Miller

Gold adsorption from cyanide solutions by activated carbon has been studied at great length during the past decade. Findings from past research are reviewed and discussed with respect to structural features of various carbons, including carbon black, activated carbon, graphite and diamond.

Jan 1, 1991

By Ruiqing Li

It is possible to purify some liquid metals by exploiting the difference between the vapour pressure of the bulk metal and the minor constituents or impurities. The rates of purification can be improved by carrying out the process under reduced pressure, that is, so called, vacuum. Some commercial examples of vacuum refining are the purification of molten tin to eliminate trace amounts of lead and the refining of cobalt, also to remove lead. The objective of this paper is to review the basic theory behind vacuum refining technology in order to show how the feasibility of vacuum refining can be determined simply for a particular system by evaluating Olette's Volatility Refining Criteriont.

Jan 1, 1991

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By S. B. Breyner, A. Ressler, D. Gregurek, A. Spanring

"The changes in process conditions that frequently decrease the service life of refractory products provided incentive for RHI AG to develop high performance bricks, especially for non-ferrous metal applications. Innovative product development was required to determine suitable refractory products for improving lining life. At the Technology Center in Leoben, Austria, practical corrosion testing methods and facilities, including an induction furnace and rotary kiln, enable detailed comparative analysis of brick wear on a pilot scale. In tests that were carried out using a fayalite type slag, the newly developed RADEX VFG magnesia-chromite grade showed very promising results compared to the standard grades. Based on the test results, optimal refractory solutions can be recommended for this challenging industrial application and field trials can be performed directly at the customer's site.IntroductionThe complexity of metallurgical processes in the non-ferrous metal industry, and especially changes to the process conditions in combination with the diversity of metal processing furnaces ''', requires a precise understanding of each individual system for appropriate refractory product selection l2'. In addition, particular importance is focused on the specific refractory consumption being as low as possible.Another important aspect results from the global shortage of resources, which forces companies to invest in recycling processes. In the base metal industry, recycling operations have resulted in significant changes; for example, operating with two slag chemistries and process temperatures will influence the performance of previously suitable linings. The raw material mix for primary smelters has also changed, including higher levels of secondary raw materials in the smelter feed."

Jan 1, 2012

By Reed M. Izatt

SuperLig® materials are capable of individually separating Rh, Pd, and/or Pt in highly purified form (99.95 to 99.99%) from a variety of chloride-based feed streams in a single stage operation. The hydrophillicity and associated kinetics of the supported materials allow for operation at relatively high flow rates of both loading and elution in a packed bed format. Pilot and commercial systems have been operated with Rh, Pd, and/or Pt present in the feed from single digit ppm (mg/l) to tens of g/l. A dual SuperLig® system for one pass Au(CN)2- separation followed by Cu and CN- recovery for CN- recycle has also been tested up to a pilot level,

Jan 1, 1999

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By M. H. Erten

Most of the fourteen workable coal seams in the State of Missouri have high ash and sulfur levels and need beneficiation in order to meet customer and Environmental Protection Agency requirements. If proper ash and sulfur removal methods can be designed, more Missouri coals will be mined and used within the state. One of the main objectives of this research is to investigate the possibility of removal of sulfur of Missouri coals by conventional beneficiation methods.

Jan 1, 1982

By Robert E. Moore

Renewed interest in olivine refractories has led to efforts to characterize them employing modern techniques of experimentation and data analysis. Initial studies have focused on determination of physical and thermophysical properties. Special equipment for the determination of thermal shock resistance and creep behavior have been constructed. Optimal compositions for maximizing various properties are being identified using appropriate statistical techniques. The overall goal is to develop response surfaces for each of a selected group of engineering design and use properties. Development of ?olivine Refractories? in the United States The term "olivine refractories" is used here because it does appear that domestic deposits of this rock will be the focus of renewed interest and "olivinell is the preferred term in this country. There are extensive deposits of high quality olivines extending through parts of Georgia. North Carolina and in the state of Washington. The eastern olivines are much more localized and extensively altered compared to the western materials. The Washington olivines exist as massive rock deposits in the Twin Sisters mountain area northeast of Seattle and their inaccessi-bility has slowed efforts to develop them. The North Carolina olivines have been used in steel plant applications since the 1930's. Geologists use the term "olivine" to describe assemblages of ortho-silicates. 2RO.SiO2, wherein the RO may be MgO. FeO. MnO. etc. When the RO consists essentlally of MgO and FeO. the material is called dunite and. as such, is synonymous with "refractory olivine." Refractory olivines utilizing North Carolina materials were developed for brick products by Birch and Harvey in this country around the mid-1930's. (I) Their work was completely independent of that of V. M. Goldschmidt and co-workers who used massive dunites located in Denmark. (2) These deposits are currently being mined by A/S Olivine of Denmark for the manufacture of a rather complete line of brick shapes for use in steel-plant. glassplant. and cement kiln applications. Birch and Goldschmidt

Jan 1, 1982

By Nobuo Takahashi

Effective solvent extraction media have been investigated for purification of rare earths. At first, a quaternary ammonium compound was studied. The counter anions of rare earths and organic dielectric substances were tested to improve separation factors,. And second, crown ethers were selected for extractant. Several diluents of crown-adducts were tested to improve solubility and distribution coefficient as well as the counter anions of rare earths. Especially, in the presence of strong reducing agents, highly selective extraction of europium from other rare earths was observed. The third extactnts were ß -diketones. Presence of organic dielectric substances was very effective to improve separation factors. Though those. three groups of extractants were suitable for mutual separation of light rare earths, alkyl esters of alkyl-phosphonic acids were suitable for mutual separation of heavy rare earths because of their high separation factors. To keep proper pH value was necessary for acidic extractants, so control method of the solution pH was studied with high molecule insoluble amines or salts of those.

Jan 1, 1995