Search Documents

By Kathryn C. Sole

A novel solvent-extraction process for the refining of gold was recently commercialised, with the commissioning in May 1997 of a 24 t a-' refinery at Harmony Gold Mine in Virginia, South Africa. The MinataurTM Process (Mintek Alternative Technology for Au Refining) uses solvent-extraction technology to produce gold of 99.99% purity from the cathode sludge arising from a conventional carbon-in-pulp / electrowinning circuit. Implementation of this process introduces significant cost benefits compared with the conventional dore smelting / toll-refining route previously followed. This paper outlines the process, presents selected operating results obtained during the first few months of operation, and provides some details of the associated techno-economic advantages.

Jan 1, 1998

By Graham J. C. Carpenter, Marc Charest, Jason Lo

"The method of producing magnesium-based composites with silicon carbide (SiC) particulates embedded in the matrix of magnesium AZ9I D alloy by the squeeze-casting technique are described. This method involves the fabrication of a SiC particulate preform and the subsequent squeezing of molten magnesium into the preform. In this study, alumina, aluminum phosphate and a proprietary binder were used for the fabrication of SiC particulate preforms. The procedures employed in the fabrication of SiC! AZ9ID composites are presented, together with the results of characterization of the composites using optical and transmission electron microscopy. Special attention is given to the reaction products in the bulk alloy and at the interfaces between SiC particles and the AZ9ID matrix alloy.1. IntroductionInterfacial, microstructural and metallurgical characteristics play an important role in determining the mechanical properties of a composite. In theory, reinforcing magnesium with SiC particulates should provide an improvement in strength and modulus of the composite over the unreinforced counterpart. However, many factors resulting from the fabrication process can cause degradation rather than improvements to the mechanical properties. In particular, the interfacial characteristics are known to critically influence the properties of composites [1]. Before evaluating the mechanical properties of a composite, it is always useful to examine the microstructure, which is closely related to the mechanical behavior. This helps to reduce the labor-intensive steps of sample preparation for mechanical property evaluation, which can be particularly difficult as a result of the high hardness of composite materials, as well as providing a wealth of information on the microstructural and interfacial characteristics, particularly the reaction products caused by processing. This information is also pertinent in understanding the factors governing the mechanical properties of the composites.There are many factors which determine the nature of the interfacial characteristics of a SiClMg composites. Qualitative estimations of the interfacial bonding have been performed based on thermodynamics, electronic and electrostatic concepts. In addition, the kinetic conditions during the fabrication play an important role. From an interfacial energy standpoint, the driving force for the formation of a metal/ceramic interface is the decrease in free energy that occurs when intimate contact is established between metal and ceramic surfaces. The simple representation of the energy change per unit area of interface formed (~G) is given by Dupre equation [2]:"

Jan 1, 1996

By D. J. Wang

Based on the thermodynamic arid kinectic aspects, the vaccum distillation processes for the separation and recovery of metals from wastes are analyzed. As to the separation criteria, The separation coefficient and equilibrium composition relation between vapor phase and liquid phase are the bases of recovery of metals by vacuum distillation, The vaporization rates and condensation mechanisms are also discussed. Some experimental results which deal with metals-containing wastes are described and the performances of a new kind of horizontal vacuum furnace are introduced, which demonstrate that , vacuum distillation may be a prospective technique for circulation and regeneration of some non-ferrous metals from industrial wastes.

Jan 1, 1996

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited ("MIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMELT plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

By Kevin L. Gering

A detection method and apparatus have been developed to perform real-time measurement of aqueous free cyanide, C-. A laboratory prototype can measure cyanide ranging from 5 micrograms ,per liter to 100 milligrams per ?liter for analysis times as short as 2 minutes per measurement. Sample size per measurement is typically only a few mI, thus? minimizing the waste volume produced from spent samples. The basis for this detection device is a quantifiable, stable affinity between the electrode material and free cyanide in the sample; The electrode exhibits piezoelectric behavior, allowing it to be used as a microbalance. This technology 'has experienced two generations of laboratory prototypes, and has been thoroughly tested to determine the operational sensitivity toward process variables such as pH, competing reactions, etc. The speed and ,accuracy of this method make it superior to conventional wet chemistry methods used for quantifying cyanide levels in water. A device based on this technology could be useful in areas involving process monitoring and environmental compliance, .particularly in the cyanide-based leach mining industry. Interest for this detector has been shown by the gold mining industry and others. Patent application is in progress.

Jan 1, 1998

By Philip Arthur

The ISASMELT process is making a significant contribution to the global metals industry. ISASMELT furnaces are now operating successfully in eight different countries and treating approximately 3 million tonnes of concentrates and secondary materials per year. The process is currently used in both lead and copper smelting. The most recently commissioned plants were in Germany and China, one for treating scrap copper and the other treating low-grade copper concentrates. The Copper ISASMEL T furnace ("CIF") at Mount Isa Mines Limited (UMIM") has continued to set new operational records, with throughput of more than I million tonnes of concentrate per year and very low operating costs. This paper summarises the latest operational data from the Mount Isa Copper ISASMEL T plant and outlines the successful approach to industrial R&D taken by MIM in the development of the ISASMEL T process.

Jan 1, 2003

By V. A. Luganav

The behavior of arsenopyrite under heating has been studied by many scientists. It has been already established that under heating at more than 650°c and without air access the arsenopyrite dissociates with the formation of one atom arsenic. Under vacuum the dissociation process begins at 5500C with the formation of elemental arsenic. The residue of dissociation process contains pyrrhotite and throilite. In the presence of pyrite, arsenopyrite dissociates under lower temperature and with a higher velocity than without it. The industrial realization of fool scale processing of arsenic bearing raw materials is possible only by the use of standard equipment and oxygen containing blast. In this view the paper presents the results of the study on the effect of oxygen in the gaseous phase and its addition into the charge of pyrite in the process of arsenopyrite decomposition. Thermodynamic analyses showed that under thermal processing of arsenopyrite in the presence of pyrite and limited quantities of oxygen in the gaseous phase the formation of arsenic sulfides is possible according to the following reactions:

Jan 1, 2003

By N. J. Tannyan

Laboratory bath smelting tests were conducted to determine the feasibility of smelting nickel- copper concentrate directly to a low iron matte in one step. Concentrate, air/oxygen and a silica flux were fed to a matte-slag bath kept in MgO crucibles at I 300°C. Various oxygen enrichments and smelting rates were used to maintain 0.5 to 2 wt% iron in the product matte. The slag losses are comparable to those obtained under similar industrial conditions. Due to the highly oxidizing conditions required to produce mattes with low iron contents, it is not recommended to target iron contents below about 2% in the matte. The specific bath smelting rates were equal to or higher than those in various industrial bath smelting processes.

Jan 1, 2003

By Gus Van Weert

Solvent extraction of iron from zinc refinery liquors has been investigated before, mainly on the MEHPA / HC1 stripping combination. Leakage of chloride into the zinc electrolyte and the costs of handling the ferric chloride eluate have prevented this option from being adopted. This work explores the stripping of the ferric loaded organic phase with nitric acid to take advantage of the possibility of regenerating up to 6N nitric acid, and clean spheroidal hematite production by autoclave treatment of ferric nitrate solution. The work was carried out with DEHPA (di 2-ethyl-hexyl phosphoric acid) in kerosine. Degradation testing proved the DEHPA to be very stable, when exposed to nitric acid solutions up to 6N and temperatures up to 70" C over a period of five days. Ferric iron was removed completely froma synthetic hot acid leach liquor, irrespective of the DEHPA concentration. Stripping the ferric turned out to be the problematic step. Although the stripping efficiency was considerable better at 50 than at 20° C, it decreased with increasing DEHPA/Fe ration in the organic phase. Eluates of no more than 5-10 g/l ferric nitrate were produced. surprisingly, nitric acid was found to be a less efficient stripping agent than sulphuric at equivalent normality and its efficacy levelled off above 4N. It was concluded that DEHPA does not appear to be the S.X. reagent to take advantage of the low cost autoclave decomposition of ferric nitrate opportunity in zinc hydrometallurgy and that another S.X. reagent, also resistant to nitric acid, but based on weaker compound formation is needed.

Jan 1, 1998

By C. Abruzzese

This work concerns a process for the inertization of asbestos-containing wastes and the subsequent recycling of the inerts for the production of ceramic refractories. One of producted refractories is cordierite, that is widely used in the electronics industry and also in mechanical engineering for the manufacture of catalytic converters for automobiles. The process thus achieves the twofold objective of eliminating toxic and harmful refuse containing asbestos, while making available high-tech materials at a reasonable cost.

Jan 1, 1998

By Jin-yan TIE, Ke-xin JIAO, Qian Li, Hai-bin ZUO, Jian-Liang Zhang, Meng SHEN

This paper designs three factors such as temperature, pH, conductivity and three levels of orthogonal test. Temperature is a significant factor. However PH and conductivity are not significant through poor analysis. Further research is conducted on the temperature. Temperature stability is 50 . Suitable water velocity is 2.3m/s, which is calculated based on the largest part of the heat flux intensity and the corresponding water temperature should be controlled with 1.5. Meanwhile, water velocity increased has little effect on the heat transfer capabilities.

Jan 1, 2015

By Adolfo Pillihuaman, Alberto Nogueira, Cyro Takano, Marcelo Mourão

The organic household waste has a growing disposal problem, requiring costly disposal systems. It is necessary to find new applications for these materials; one could be the steelmaking raw material production. In this paper is studied the development of self-reducing pellets from the organic waste pyrolysis, where is generated carbon and condensable and non-condensable volatiles. Non-condensable volatiles were burned and condensable volatiles were recovered. The resulting tar was mixed with iron ore, coal powder and flux (CaO), to then be pelletized together. Compression, falls and tumbler tests were conducted to characterize the pellets before and after heat treatment and reduction processes. The reduction curve and their physical and morphological characterization were measured. The results were as was expected, the fluidized coal create sufficient adhesion that pellets earned resistance with an equivalent resistance of common pellets, showing a good feasibility of this process.

Jan 1, 2015

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By O. Forsén

In the first part of this paper is studied the behaviour of small amounts of impurity elements? in the solidification of copper anodes. In the second part the dissolution of these impure anodes in sulphate based electrolysis is discussed. The first part is introduced with practical examples, the .model of solidification of impurities during the solidification of anode copper. According to this model the solidification structures of anode copper are strongly influenced by both thermodynamic and kinetic factors. Thermodynamics determine the microstructure of anode copper, but kinetics can alter the composition of melt to such that there is formed unequilibrium structures during the solidification, especially when the residual melt is solidified. The electrolysis experiments have clarified the behaviour of impuririties in the electrochemical dissolution in sulphate. Based copper electrolysis. In this study it is widely investigated to what extent any impurity elements or oxides will dissolve. In copper electrorefining. With the aid of the electrochemtcal experiments it was possible to fulfil quantitatively the qualitative results accomplished by microstructure studies.

Jan 1, 1985

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By James W. Evans, Dong Xu, Jr. Jones

A physical (water) model based on particle image velocimetry (PIV) has been constructed at UC Berkeley. The PIV technique enables the use of water modeling to quantitatively characterize the fluid flow behavior in the mold during the continuous casting of steel, in a whole field sense, i.e., section by section. A method to obtain e\e time-averagevelocity (TA V) vector maps was developed by averaging 40 instant aneous vectc -r plots revealing the time average features of the flow. Another benefit of TAV vector maps is the ability to compare with present mathematical models, which are mostly based on the time-average technique. Bifurcated submerged entry nozzles (SEN) with ports inclined at various angles to the horizontal were used in the modeling to study their effects on the flow inside the caster. Argon was also introduced into the model to simulate the influence of argon injection on the metal delivery from the tundish into the caster. The bubble sizes and distribution (in specific sections) of argon were characterized, at the same time, by the imaging system of the PIV. This will allow for validation of current mathematical models that were developed to simulate argon injection in casters. Comparison with results calculated by the commercial finite element package FIDAP is also presented.

Jan 1, 1998

By Gopalakrishna M. Rao

"Several industrial and government laboratories are of the opinion that solar--cell technology will grow into a billion-dollar industry by the year 2000, especially if oil prices rise again. Of the variety of materials that have been investigated as the major component of photovoltaic systems, silicon appears to have an outstanding advantage. The cost factor is the primary importance in photovoltaic development, since the technology to make silicon cells of acceptable efficiency and life time has existed since the early stage of the space program. Electrometallurgy is one of the low--cost processes for the production of silicon, since it allows direct, single-stage production from some abundant, inexpensive source materials such as silica and fluorosilicates. Among several systems, two are given particular attention, using inorganic baths with Si0 2 or K2SiF6 as the source of silicon respectively. They appear capable of development to commercial production. Conceptual designs of a commercial--scale cell for silicon production at temperatures above its melting point, and of a pilot' plant for plating silicon from an all-fluoride bath are presented. Energy ProspectsThe major changes in the world energy since the first energy crisis in 1970 have impacted on our community. When oil was $40 a barrel in the mid-1970s, we became obsessed with the energy conservation and a search for alternate energies. Even though the crude oil fell below $15 a barrel during the last several years, our energy security fears continue to haunt us. This time it is not the scarcity, but the abundance of foreign oil and the decline in the domestic production.The prospects of energy depends on the demand and supply of energy. These, in turn, depend on future energy prices, which are linked to economic factors, political events, and unforeseen circumstances. Although no one can predict the future with certainty, three energy consumption patterns used by the Ford Foundation are as shown in Fig. 1."

Jan 1, 1988

By Joon H. Jang

At a selected pH, hydrothermal oxidation of chalcopyrite was carried out under controlled F+,, at elevated pressures and temperatures (172-200°C) by balancing the rate of oxygen injection against the rate of consumption. Chalcopyrite was converted to covellite (CuS) and digenite (CU1.8S) with rejection of iron and sulfur to the solution. Covellite forms in the first stage, followed by nucleation and growth of digenite in the second stage. The effects of rapid and slow injection of stoichiometric quantities of oxygen are compared. Both the covellite and digenite form a porous layer occupying the same volume as the original chalcopyrite grain. An electrochemical kinetic model is presented to correlate the observed results.

Jan 1, 1993

By R. H. Crist

Reactive components of algal cell walls include uronic and alginic acids: In addition, many marine species have half ester sulfate groups which function as fixed anions. Associated metals vary with the media, eg., Ca and Mg in fresh water (FV) and Na, Ca, Mg in seawater. . These metals readily exchange with aqueous phase protons or metal cations. A plot of the total amount of metal cations displaced by protons vs .. pH shows one inflection at pH 4 for FV algae and' in addition a second inflection at pH 2, 3 for marine algae. The first inflection is interpreted as. Indicating the cations associated with carboxyl groups ,and the ,second with half ester ?Sulfate groups. The exchange capacities of various aigal ,species vary widely. When FV algae is placed in a Pb2+ solution,- the amount of Pb2"' deposited on the algae is. Equivalent to the. Total Ca2?, Mg2, and H+ displaced? thereby confirming the ion exchange mechanism. Ion exchange equilibrium constants are reported for the displacement of ca2+ from Vaucheria. With Mg2+, sr2+, Cd2+, Pb2+_ and Na+ as well as the reverse reactions. Cd2+ can .be removed partially from algae by precipitating it as CdS or Cd(OH) 2 Pb2+ and Cu2+ are also partially removed as the hydroxides. Rates of reaction for various alkali hydroxides decrease with increasing .unhydrated cation radius. It is concluded that theory is useful in predicting viable applications for algae in pollution abatement.

Jan 1, 1991