Search Documents

By Khaled Morsy

The studied mine extracts the Sewickley seam using room-and-pillar method. The overburden at study site ranges from 400 to 800 ft. Eight years earlier, the Pittsburgh seam was mined 80 ft underneath the Sewickley seam. Parts of the mains at the study site experienced problems of rib spalling associated with floor heave. Numerical modeling was used to explain the mechanism of ground control problems encountered at the mains of the upper seam. The modeling results show that the ground control problems encountered were caused by multiple seam interactions with the previously mined longwall panel of the lower seam. Based on the modeling results, a criterion to predict the probability of multiple seam interactions was proposed.

Jan 1, 2006

By Denise Weber, Jürgen Kateloe, Marku Papst, Laurenz Preusse, Axel Preusse

"The angle of draw (in Germany, referred to as Limit Angle) plays a significant role in the field of mining subsidence engineering. This applies both to the assessment of the affected area by underground mining activities as well as applied methods for the prediction of ground movements.Recent observations using remote sensing show that ground movements outside the affected area defined by the angle of draw have been detected in German hard coal mining. Since the affected area by underground mining activities also plays an essential role regarding claims of landowners with damages to their houses and infrastructures, possible solutions for limiting the size of the affected area will be presented in this paper.Ground movements which exceed the affected area of an underground coal mine, as defined by the angle of draw will be shown in an exemplary manner. Present knowledge indicates an expectation that ground movements outside the affected area will not cause damage of major significance.This paper outlines the consequences for all affected parties regarding ground movements due to underground coal mining that exceed the extent of the area defined by the currently assumed angle of draw. This will be visualized in a case study.INTRODUCTIONGermany has a long tradition of coal mining, especially in the mining area of the Ruhr district. Following a long period of mining activity, the area is now highly populated and densely developed. In such an environment, it is of utmost importance to calculate and predict ground movements initiated by mining activities; therefore, the research here focused on the prediction of ground movement for the last decades. Special attention was given to the development of accurate ground movement models, which can be utilized in all mining areas. These models are based on different influencing factors such as depth of mining, worked thickness and the angle of draw.Depending on these models, the mining companies calculate the area of land subsidence; the predicted results are used for financial calculations and planning. For structures on top of zones with a high risk of deformation, structural measures can be applied, construction warnings can be given and, in cases of damage, compensation can be planned. The technical and economic planning was performed for all areas of mining subsidence. The most important factor for the outer limits of mining subsidence is the angle of draw (Ger. Grenzwinkel), which plots the border of the area of mining subsidence."

Jan 1, 2015

By H. Nan

Using the case of Qianqiu Mine, Yima Coal Mining Administration, theoretical analysis, laboratory physical simulation, and underground observation were performed to study the major parameters for fully mechanized sublevel caving mining method, including drawing spacing, drawing sequence, drawing numbers, and number of shields performing simultaneous drawing. The effects of those parameters on coal recovery and amount of waste rocks were also investigated. The optimal coal drawing technology for this case was obtained.

Jan 1, 2006

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

By Russell Frith

For many years, underground rock mechanics and in particular, roadway/tunnel roof stability has been underpinned by the often unchallenged assumption that roof strength (as defined by the UCS) and stiffness (E) are key stability controls. This has logically led to the proliferation of laboratory testing of rock specimens and the development of indirect geophysical methods to gain estimates of these two rock parameters. Furthermore, many design methods are significantly focussed on replicating rock mass behaviour through either intact or failed constitutive models. Demonstrably the strength and stiffness of the host rock material is commonly used as one of the key indicators of excavation roof stability and it finds either direct or indirect use in just about every rock mass rating system in use today. In more recent times there has been a common move to consider and apply (even if only conceptually at the current time) structural engineering type principles (e.g. buckling) to coal mine roadway roof (and rib) stability. Similarly our knowledge of the in situ stress environment and its likely origins has improved significantly, largely through stress measurements and subsequent analysis. This paper combines knowledge in both of these fundamental areas through a deterministic model for roadway roof stability and in combination with field examples, reaches the almost certainly controversial conclusion that UCS and E are commonly irrelevant, albeit that the former may provide an indication of other relevant geotechnical parameters (e.g. bedding cohesion). As with all hypotheses or rules, there are naturally exceptions and in this case, the most obvious is the tailgate of the longwall panel (with adjacent goaf). Due to the significant change in the strata loading environment of a longwall tailgate as compared to first workings for example, the stability equation materially changes so that UCS and E become critical controls. The point of the paper is to present a different perspective on a traditional mining problem and to challenge geotechnical professionals to keep thinking ?outside of the square? in the never-ending endeavour to improve our understanding of the engineering problems we regularly face. Such an understanding impacts upon such issues as geotechnical data collection from borecore, support hardware requirements and design capabilities. Therefore making the assumption that our understanding is always fundamentally correct could in fact be limiting the development of new and improved engineering in the future.

Jan 1, 2006

By Brent A. Slaker, Michael Murphy, John Ellenberger, Erik Westman

"Photogrammetry, as a tool for monitoring underground mine deformation, is an alternative to traditional point measurement devices, and may be capable of accurate measurements in situations where technologies such as laser scanning are unsuited, undesired or cost-prohibitive. An underground limestone mine in Ohio is used as a test case for monitoring of structurally unstable pillars. Seven pillars were photographed during four visits over a 63- day period. Using photogrammetry, point clouds of the mine geometry were obtained and triangulated surfaces were generated to determine volumes of change over time. Pillar spalling in the range of 0.29–4.03 m3 of rock on individual rib faces was detected. Isolated incidents of rock expansion prior to failure, and the isolated failure of a weak shale band, were also observed. Much of the pillars remained unchanged during the monitoring period, which is indicative of proper alignment in the triangulated surfaces. The photographs of some ribs were of either too poor quality or had insufficient overlap, and were not included. However, photogrammetry was successfully applied to multiple ribs in quantifying the pillar geometry change over time.IntroductionAdequately measuring underground rock mass movements is integral to understanding how rock masses behave and how to interact with them safely and efficiently. Many modern measurement techniques employed in underground mining environments rely on point measurements, such as through extensometers or borehole relief methods (Christiansson, 2006). These techniques, while commonplace, do not provide a comprehensive view of how the rock mass is behaving. The dynamic changes in stress states underground, coupled with the mechanical uncertainty of rock masses, near active excavations, creates a need for measurement systems which better capture the behavior of the rock mass. Photogrammetry is a technology capable of producing the wide-area displacement measurements required for a comprehensive understanding of rock mass movements.Digital photogrammetry is a means of obtaining threedimensional point clouds from digital photographs. By finding the same point across multiple images, all viewing an object from different angles, the location of that point in three-dimensional space can be inferred. Close range digital photogrammetry (CRDP) is photogrammetry applied to measuring objects or scenes less than 100 meters away (Atkinson, 1996), and is used for various functions in underground mining environments. These uses include, but are not limited to, mapping fracture networks (Kim, Kim, & Won, 2005)(Somervuori & Lamberg, 2010), characterizing fractures (Styles et al., 2010) and measuring volumes of blast rock (Heal, Hudyma, & Potvin, 2004)."

Jan 1, 2015

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By Madan M. Singh

Mining under bodies of water such as oceans, lakes, rivers, streams, ponds, and other impoundments, is not a new technique. However, in the United States it has been fairly restricted to date. In order to recover the maximum amount of the nation's reserves, in the future, it is important that further mining under such bodies of water be planned. However, it is imperative that this is not done at the expense of danger to the nation's miners or appreciable property damage. If all the bodies of water are considered large, and it is assumed that these constitute a hazard when mining in their vicinity irrespective of their size and geometry, a significant percentage of the coal reserves are likely to be sterilized. How- ever, by adopting special mining plans and procedures, it may be possible to release reserves for exploitation that would otherwise be unmineable since the surface of bodies of water below which they lie are relatively small in size. In 1977, the Bureau of Mines issued Information Circular (IC) 8741, entitled "Results of Research to Develop Guidelines for Mining Near Surface and Underground Bodies of Water". This document was based on the work done by Skelly and Loy (under Contract No. H0252083) and K. Wardell and Partners (under Contract No. H0252021). How ever, these guidelines have limited application, because these did not (1) define the bodies of water of concern, and (2) take into account the nature of the strata being encountered. These guidelines assumed that all bodies of water which would be undermined were large. For the purposes of this discussion, water bodies may be divided into three categories, depending upon their potential to cause damage to the underlying mining activity: ? catastrophic ? major ? limited Bodies of water which pose the threat of catastrophic destruction in the mine, should there be an inrush, include oceans, large lakes, big inland reservoirs, and rivers that could flood the mine complete- ly in a short period. Those with major potential for damage would include lakes and streams which might present a danger to both life and property if not considered in the mining plans. Finite bodies of water which have a volume considerably smaller than the mine volume offer a limited potential for damage in the case of an inrush. These include flowing streams which have a relatively small rate of replenishment and which can be dealt with by pumping or isolation in the event of a breakthrough into the mine. Such bodies of water may be inconvenient and cause a temporary disruption of production, and could even cause some damage to equipment, but only in rare instances would personal injuries occur. The scope of this paper is limited to the exploitation of stratified mineral deposits with overlying -face bodies of water. Vein and dessiminate ore deposits are not discussed, nor are breakthroughs into adjacent mines in the same horizon. Overlying, water-logged strata also pose a serious threat to mining, but are not treated in this discussion. Pending further investigation these strata may be considered as bodies of water with catastrophic potential for damage, with the base of the strata being considered the bottom of the water body. When the body of water is large, so that it may cause catastrophic damage to the mine in the event of an inrush, the guidelines suggested in IC 8741 are applicable. In order to develop criteria and procedures for mining under smaller bodies of water, however, it is necessary that the nature of the strata disturbance due to underground mining be examined.

Jan 1, 1981

By Yongping Wu

The steeply dipping coal seams in this paper refer to those with the angle of inclination ranging from 35° to 55°. The reserves of the steep coal seams account for approximately 15%~20% of the total coal reserves in China. In the past 12 years, the top-coal caving mining method had been used to mine the steeply dipping thick (11.5-16.4 ft or 3.5-5.0m) coal seams. However, the mining process of top coal caving is complex with low recovery rate and nearly 30% of coal was wasted. Those problems can be solved by using the single pass large mining height (11.5-16.4 ft or 3.5-5.0m) method. But the movement of the overlying strata around the mining face area of large mining height is complex and it is hard to control the stability of ?rock-shield support? system. Therefore, field measurement, numerical simulation and physical (similarity material) simulation methods were used simultaneously to analyze the strata movement, roof structure and rock-shield support interaction characteristics. The results indicate that strata movement, which is the same as mining the steeply dipping seams with conventional mining heights, is asymmetrical about the dipping direction of the face; deformation, failures, and movement of the surrounding rocks are more intense; the roof weighting interval decreases; the weighting intensity increases significantly; and face sloughage occurs frequently. In the gob, the space for sliding and rolling of the roof increases; the broken main roof tends to form an anti-dip pile structure; the backfilling and compactness of broken roof increase at the lower portion of the face, thereby inducing significant unbalance in stress distribution between the upper and lower portions of the face. The overlying strata above the face form a multi-level step structure. The characteristics of contact and loading of roof-shield support system are more complex. The range of shield load variation is larger, and interaction between shield supports occurs frequently. Anti-toppling and anti-sliding devices at the face become more difficult to implement. The research results provide a theoretical basis for the mining practices in the steeply dipping thick seams with a large mining height. The practice in panel 25221 of 2130 coal mine indicates that the accident rates have been greatly reduced and good technical and economic benefits have bee realized.

Jan 1, 2014

By Wenbing Guo

Strip pillar mining method is one of the most important techniques for mining subsidence control in China. Mining depth is one of the most important factors that affect subsidence in strip pillar mining method. Six numerical simulation models were set up in this paper to simulate surface subsidence of strip pillar mining at different mining depths. The mining depth in these models ranged from 300 to 800 m. The simulated results were compared and analyzed. The results showed that the subsidence factor of strip pillar mining is related to mining depth. While other things being equal, the subsidence factor of strip pillar mining increases logarithmically with increase in mining depth. Their quantitative relationship was established based on the simulated results.

Jan 1, 2007

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Collin Stewart

Bowie Resources, LLC (Bowie) has been using the Stability Mapping System (SMS) developed by Dr. Keith Heasley, West Virginia University, since 2005. Seven three-entry longwall gateroads, four longwall panels and a five-entry set of mains have been mined in two different seams in areas originally analyzed with the SMS. This paper compares predictions of mining conditions based on the SMS with actual mining conditions. Specific comparisons include longwall and continuous miner (CM) productivity, longwall tailgate response and support and CM roof bolting requirements. The paper also discusses current thoughts at Bowie on the use of different weighting factors for CM development, longwall face conditions and longwall tailgate support requirements.

Jan 1, 2007

By Yongjie Yang

Experimental study on the strength and deformation characteristics of coal under cyclic loading provides guidance for designing coal pillar which is subjected to repeated mining influence during mining. This paper studies the strength, deformation and fatigue process of No.3 coal from Xinhe Colliery under cyclic loading by the MTS815.03 servo-controlled rock mechanics test system. The results indicate that coal is more susceptible to fatigue damage than other hard rocks. Under uniaxial cyclic loading, the fatigue failure ?threshold value? of coal is smaller than 78% of its uniaxial strength, and there is also some fatigue damage when cyclic loading and unloading experiment is carried out below the fatigue failure ?threshold value?. Axial deformation can be divided into three stages: Initial deformation, steady-state deformation and accelerating deformation. Transverse deformation can be divided into two stages: Stable deformation and accelerating deformation. When the transverse deformation begins to increase rapidly and the deformation recovers only slightly upon unloading, it?s a precursor to failure of coal. Under cyclic loading, fatigue failure develops through a process of compaction, strain hardening, and strain softening.

Jan 1, 2006

By C. Thomas Blevins

This paper is intended to be a hands on experience account about ground control in a Southern Illinois coal mine. Its aim is to show how a combination of real world mining practices and constraints along with practical engineering theory mesh together to formulate a ground control program in adverse conditions. These conditions - your typical localized slips, splits, rolls, clay intrusions, water, changing types and thicknesses of materials, etc. - being amplified by a very strong horizontal stress field. A review will be made about the formation of the overall ground control plan and to what degree it has been successful. A presentation of the various roof control systems and their component parts, how these systems were developed, and the theory behind them will be made. The pointing out of some of the flaws that we found in the components, installations, and/or theory will be part of this presentation. A brief look at some of the efforts in the following items will be made: quality control of the roof control products; using the computer to help keep track of roof control information and soliciting help from various universities, governmental agencies and consultants to give different perspectives to the problem.

Jan 1, 1984

By Jin He

Based on the simple-beam theory, a stress analysis model was established for undermining in multiple seam strip-pillar mining when the strip pillars were not columnized; the effects of various mining factors (e.g., mining depth, inter-burden thickness, recovery ratio, etc.) on inter-burden stability were analyzed; the changes in inter-burden stress distribution were investigated; and the important role that the inter-burden spacing and the mining width of the lower seams on inter-burden stability was studied. Finally, the actual practice used in Feng Feng Mine area was used as an example to demonstrate the rational mining width for a fixed mining depth.

Jan 1, 2006

By Saeed Zandi, Kazem Oraee

"Tunnels and galleries are the most important structures in coal mines. They are used for variety of purposes, such as transporting ore and people and for ventilation. A well-designed support system is necessary to stabilize structures and prevent collapse.Using rock bolts increases the strength of the rock in which tunnels are made. Rock bolts are used extensively in most underground mines today, and coal mines are no exception. Almost all galleries in a typical coal mine use some type of rock bolt, at least, as a means of partial or supplementary support.In this research, changing the support system from expensive methods to the use of rock bolts as the primary means of support is discussed, with the focus on a particular gallery in Hejdak coal mine. Visionary design methods, in conjunction with rock mass classification schedules, were used to determine an optimal rock bolt pattern. For this purpose, rock mass rating (RlVIR) and quality index (Q) classification systems were used. Several empirical methods were also used to design an optimal pattern for rock bolt installation in the particular tunnel under analysis.As such, the tunnel support system was designed using both finite element and empirical methods. Finally, the results obtained from both numerical and empirical methods were compared under different load conditions. The methodology prescribed in this paper, together with the comparison, can be a useful tool when selecting a support system. The results can also be used to design a support system in this and any other coal mine with similar conditions.INTRODUCTIONSince the advent of underground excavation techniques, one of the biggest challenges has been stabilizing tunnel walls and preventing roof collapse in tunnels and other underground openings, such as galleries. Loose rocks and layers drop into tunnels and galleries, except in very hard rock. Underground roof collapse and falling rocks can have devastating effects on the safety of operation personnel and equipment and can seriously affect production. When designing an underground coal mine, the stability of tunnels and galleries is an important parameter that should be studied carefully because it has an important role in the production process of the mine. Therefore, an appropriate and well-designed support system is necessary for preventing collapse and helping to stabilize the tunnels and galleries."

Jan 1, 2016