Search Documents

By Naj Aziz

The shear behaviour of reinforced rock joints is investigated for the bolt-grout-rock interaction and for failure mechanism. The effectiveness of the bolt application under lateral and axial loading conditions within surrounding materials is investigated in different medium strength. Double shearing testing of bolts were studied in concrete blocks of 20, 40, 50 and 100 MPa strengths, subjected to different pretension loads of 0, 5, 10, 20, 50 and 80 KN respectively. The experimental study was complemented with three-dimensional numerical analysis. Parameters examined include: shear resistance, shear displacement, induced strains and stresses during bolt bending process and its ultimate failure across the sheared joint planes. The conclusions drawn from the study were; the level of bolt resistance to shearing was influenced by the bolt profile configuration, the strength of the rock or medium influenced the level of load generated on the bolt, and the increase in bolt pretension has contributed to the increased shearing load of the bolted medium.

Jan 1, 2007

By John Latilla

Exxaro Mining?s Matla Coal situated in Mpumalanga, South Africa operates two shortwall faces on the No 4 and No 2 seam while the No 5 seam has also been longwalled in the past. Severe strata loading events have lead to a number of serious roof falls on the wall face (facebreaks) resulting in safety threats as well as considerable production losses. In 2002 the No 4 seam shortwall suffered a facebreak restricted mainly to the tailgate side of the mining panel due to a thick, near surface dolerite sill not breaking properly. This was partly due to the premature suspension of longwalling in the overlying No 5 seam. The resultant overloading lead to severe pillar damage and subsequent bord collapse. Surface pre-split blasting was successfully used to relieve the pressure as well as to pre-condition the dolerite above the following two panels. The shortwall on the No 2 seam has experienced mid-face loading due to No 4 seam chain pillars lying over this area and creating a secondary cantilever effect. Pre-split blasting of the solid rock above the No 4 seam pillars has resulted in a significant reduction in the number of facebreaks. The panel layout of the No 2 seam was subsequently changed so that the chain pillars on both the No 4 and No 2 seam are superimposed whereas previously they were offset.

Jan 1, 2007

By Thomas M. Brady

The Spokane Research Laboratory/NIOSH and the University of British Columbia (UBC) geomechanics group are focusing on the development of safe and cost-effective underground design guidelines for weak rock masses having an RMR in the range of 15 to 45. Weak ground conditions, ground support, and mining methods used in several North American underground mines were observed. The RMR values were calculated to update both manned entry span design and non-entry stability graphs, plus a database on underhand mining methods was created to reflect existing North American mining conditions. The immediate rock mass was characterized and analyzed in terms of prevailing type of ground support, potential failure mechanisms, and rock behavior to define how existing design curves must be modified for the existing weak rock mass. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making sound economic decisions that will also ensure a safe working environment.

Jan 1, 2006

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By Nic Slatalla

Acoustic emission monitoring techniques are a powerful tool for analysing deformation behaviour and fracture characteristics of rock samples under uniaxial loading. Uniaxial compression tests were carried out on three different types of sandstone for a better understanding of acoustic emission response with respect to rock deformation and damage develop-ment. All sandstone samples revealed congruent characteristic acous-tic emission patterns which correlated directly with distinct stress-strain stages. However, the acoustic response and development within the individual stages proved to be entirely different due to variations in their microstructure.

Jan 1, 2008

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Keith Heasley

In many practical situation where the LaModel program in used to analyze the mechanical response and failure of the mining environment, there are very few actual field measurement from the site available for deriving the appropriate input parameters. For coping with this typical lack of field data, this paper presents some recommended calibration techniques derived from on an in-depth understanding of the laminated model formulation and from many years of experience applying LaModel to practical situations. For each of the critical input parameters (rock mass stiffness, gob stiffness and coal strength) in LaModel, a specific calibration technique is recommended and presented along with the justification for the technique and some appropriate derivations/equations for assistance. It is hoped that this frank discussion of recommended calibration techniques can help novice LaModel user develop better models and can initiate a discussion among rock mechanics experts on how to improve upon the presented techniques.

Jan 1, 2008

By Peter Fischer

Reducing mining costs has become such an important factor in the German coal industry that operators are forced to work only those areas where production costs can be kept low. These areas will normally be located close to the mine shafts because they are easily accessible. Even the shaft pillar is now being considered as part of the winning zone. Before working coal in shaft pillar zones it is essential to assess the impact this will have on the shaft lining. There is a huge difference between sliding and strata-anchored shaft systems. However, if the overburden comprises lightweight soil both types of shaft will have a tendency to protrude from the surrounding ground. This paper presents the geomechanical reasons underlying this reaction and the methods used for predicting and measuring it.

Jan 1, 2007

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of ?but which formula is the right one?? The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: ? Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) ? Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) ? Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which concentrates on the SF of the webs, and the other which creates a ?pressure arch? using properly sized barrier pillars. The paper will close with a discussion of some current needs in coal pillar design, including: ? Updating older empirical methods, such as ALPS, where changes in technology (new types of roof support, more demanding ventilation requirements, faster retreat rates) may have made some of the original case histories obsolete. ? Methods for determining site-specific coal strengths, focusing on bedding plane strength and other factors that may effect confinement, as input for both empirical and numerical design. ? Improved methods for evaluating coal pillar performance for environmental issues, such as surface subsidence and hydrologic impacts, which consider such factors as depth, w/h ratio, water immersion/drainage, and time dependent seam strength.

Jan 1, 2006

By R. F. Valene

This paper is not available for inclusion in the Proceedings at the time of printing. but it will be included as an insert

Jan 1, 1984

By Kazem Oraee-Mirzamani, Nikzad Oraee-Mirzamani, Arash Goodarzi

"Unexpected movement of ground can potentially endanger lives, damage equipment or destroy property. Occupational accidents frequently occur with fatal consequences in developing countries with significant economic dependence on industries such as mining. Therefore, there is increasing need for miners' protection against such hazards. Slope stability and roof support accidents are two of the major causes of fatalities at surface and underground mining operations. According to national codes, employers are obligated to protect workers against accidents; however, these rules fall short of the standards in developed countries. National safety regulations should clearly specify support systems. The International Labor Organization (ILO) prepared two codes of practice, aiming to guide those responsible for improving standards of safety and to provide guidelines for drafting of safety regulations for the coal mine industry and quarry open cast mines. The practical recommendations of these codes in the ground control area have been analysed and the advantages and disadvantages of ILO codes concerning ground control are summarized.INTRODUCTIONTwo million people die every year from work-related accidents and diseases. An estimated 160 million people suffer from work-related diseases, and there are an estimated 270 million fatal and non-fatal work-related accidents per year. In economic terms, the ILO has estimated that 4% of the world's annual GDP is lost as a consequence of occupational diseases and accidents (ILO, 2009).Mining has always been dangerous due to many potential risks such as those associated with using machinery in enclosed spaces, rock falls, blasting operations and explosion of flammable gases, which endanger miners' safety and health. However, it is suggested that implementing new laws along with strict adherence would reduce such risks in the workplace.The severity and frequency of accidents are trending downward in developed countries, where the focus is on large private companies who invest heavily in mechanization and developing economies of scale. But in many parts of the world, particularly in developing countries, minerals are extracted by people working with simple tools and equipment; they work on a smaller scale, are more flexible, and can exploit irregular ore bodies and steep, dipping seams."

Jan 1, 2010

By Andrzej Walentek

In polish coal mining due to specificity of seams lying the multiple extraction is used. In this kind of mining, it is essential to take into account all geological and mining conditions which have an influence on stability and functionality of workings during their using. In view of above, for one of polish coalmines, by mean of Phase2 program, the numerical calculation were made for assessment of the influence of advancing excavation front on convergence of roadway located 30 meters above longwall was analysed. In order to verify developed prognosis, in analyzed roadway the underground investigations in scope of convergence measurement and changes of load exerted on working support were carried. As a result of these investigations it was found that real convergence on certain part of roadway was significantly larger then determined in prognosis. Additional calculations and analysis showed that the main cause of differences was underestimation of influence of dynamic load, which was an effect of numerous low energetic rockmass tremors. These tremors, related to excavated longwall, were located in close proximity of roadway in its part where the biggest convergence occurred. In current practice, in this type of convergence prognosis, the maximal value of dynamic load exerted on roadway resulted from single rockmass tremor is taken into consideration. Quantitative consideration of all tremors including their location is impossible at the stage of convergence prognosis because of lack of this type of data. This paper presents results of roadway convergence prognosis compared to results of underground investigation. Conclusions formulated on that base allow in future similar designing works for obtaining more accurate results.

Jan 1, 2013

By Mingju Liu

China has been suffering from coal and gas outbursts since 1950s. Nowadays, the situation has become worse than ever with the need to mine deeper coal deposits at higher production rates in a more complex underground mining environment. In the year 2006 alone, 37 outbursts occurred in underground coal mines with a death toll of 232. This paper describes a case study of an outburst event, which occurred in July 2006 during the shaft development of the Mengjin Coal Mine, Henan Province, China at a depth of 768m below surface. Detailed analysis of the possible causes that led to the occurrence of the outburst is reported. These include the study of complex geological features, gas storage conditions, possible improper technical management practice as well as incomplete prevention and control measures. Based on the case study and the observation of outburst occurrence in China in the year 2007, suggestions have been put forward to help prevent and control future coal and gas outbursts.

Jan 1, 2007

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By Wenbing Guo

The stability of strip pillar is the key to successful strip pillar mining. In analyzing the stability of the strip pillar, the width of yield zone must be determined. The determination of the width of yield zone has been an important subject for researchers. In this paper, the numerical method was used to study the relationship between the width of yield zone in strip pillar and coal recovery ratio. The results showed that as the recovery ratio increases, the width of yield zone increases exponentially. Accordingly, the formula for determining the width of yield zone was updated and the effect of changing coal recovery ratio on strip pillar deformation is presented.

Jan 1, 2006

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006