Search Documents

By J. W. MacDonald

PROPERTY AND PRODUCTION: Around 100 Million Tons of Recoverable Coal are available from the approximate 10,000 acres allocated to the mine. Over 1300 acres of surface land holdings extend well beyond the limits required for plant site, storage tracks, water supply reservoir, settling ponds and waste disposal. COAL: Extensive core drilled testing confirmed the early indicated high quality of the #6 Seam Washability data show less than four percent of the' coal seam required removal to provide a superior product for the available market. PREPARATION PANT DESIGN: The limited needs enabled Preparation Plant Design to meet the requirements without inclusion of novel equipment. The simplified needs afforded ample opportunity for considering increased automation where advantage or economy was antioipated. Plant design included protection of opportunity for pre-drying in advance of air cleaning the fine coal and accommodations for addition of Dense Media separating equipment in event warranted or required by future market changes. Protection is also afforded for addition of Raw Coal Storage accommodations in event warranted. Figure I shows the Preparation Plant Flow Sheet.

Jan 1, 1961

By John B. Goddard

The discovery of rhenium on the ion exchange resin used at the uranium in-situ leach operations at Palangana (Texas) led to a laboratory study on the possible methods of recovery. Rhenium, present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, Re04-, concentrated on the anion exchange resin, which was a factor of ten more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the perchlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3[N] or stronger concentration of nitrate containing up to 0.5[N] H+ was found to be the system of choice. A rhenium sulfide concentrate containing up to 14% Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4Re04 followed by hydrogen reduction at elevated temperature.

Jan 1, 1982

By Arthur M. Ribe

In my experience, nothing helps me better to get off to a good start in preparing a paper or a talk than a copious consultation with a comprehensive dictionary. I also feel defining the perimeters of a particular subject is helpful to the listener and reader. Sometimes thus precisely defining even the most common of words is helpful. Our general topic this morning as all of you know is "Transportation of Industrial Minerals." The definition of transportation given by the dictionary which I think is appropriate here is: "Systems and modes of conveyance of persons or goods from place to place." Our preceding panelists have outlined for you the state of the art inso¬far as systems and modes of conveyance from place to place are concerned today via rail, water and motor. My assignment is somewhat different as indicated by my topic, "The Traffic Manager in an Industrial Minerals Operation."

Jan 1, 1969

By Chris A. Minnucci

In 1978, the U.S. Department of Energy funded a 2-year study to identify and quantify causes of the post-1969 coal mine productivity decline. A large number of factors hypothesized to have affected productivity during this period were analyzed using regression techniques. The results were particularly interesting for two of the factors--mining method and shift scheduling. The study results indicate that the use of longwall mining has an insignificant impact on overall mine productivity, compared to other methods, and mines operating on a two-production shift per day schedule are more productive than mines employing other shift schedules.

Jan 1, 1984

By V. K. Karra

An improvement in the present day screen sizing methods calls for knowledge on i) how material in the size range: 0.5 x 1.5 times the through-fall opening of the mesh on a deck, splits between the oversize and undersize streams of the deck, and ii) how near-mesh content of the feed affects the screening performance. In the throughput based sizing method given here, this is accomplished through the introduction of a generalized partition curve and a near-mesh factor. A newly developed efficiency factor is employed in addition to the traditional screen sizing factors.

Jan 1, 1979

By Louis A. Panek

Research on roof bolting has developed significant information with respect to the functions that can be performed by properly installed bolts and the methods that can be used to ensure that effective installation has been achieved. The present paper brings together results that are pertinent to the design of a bolting system for reinforcing horizontally stratified mine roof with vertical bolts. The design approach is based on the use of bolts to decrease the maximum bending stress within an arbitrary sequence of roof strata (such as shown by figure 1) in which the only loads are the weights of the individual beds. The use of rock bolts to achieve other objectives, such as to stabilize a fractured rock mass on the periphery of a mine opening (3), is excluded from consideration herein.

Jan 1, 1964

By R. B. Massy-Greene

Project engineering and development is a process of optimisation of capital, operating and financial costs, and extraction rates in the light of current and forecast economic conditions for the sale of the product. The aim of the process is to maximize financial returns to the sponsors (project owners) within many often conflicting constraints. Thus, the sponsor's engineering and financial staff have a common goal, with performance measured in financial terms. Consequently, each group must be aware of, and responsive to, the constraints imposed upon the other. For financial staff, the increasing size and complexity, and escalating capital costs of new ventures have required them to seek finance in larger amounts, and by non-traditional methods. In addition, senior management are requiring indications of the availability of finance as a pre-requisite to a decision to commence project development activities.

Jan 1, 1982

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By J. A. Harrison

Most coal being used in the United States has been subjected to one or' more processes of coal preparation. The physical and chemical characteristics of a coal have a marked influence on the ultimate uses that coal may have. The selection of the proper preparation processes may similarly be important in producing the best practical coal product for any particular use. The physical composition and distribution of physical constituents in the coal will partially determine the efficiency of the preparation process chosen and conversely distribution and concentration of coal macerals will, to a degree, be controlled by the preparation process. A number of preparation processes have been evaluated to determine this interrelation. If a coal having' certain specifications is desired, these evaluations trill assist in providing information needed for the production of this coal.

Jan 1, 1962

By Norbert Patzelt

Today the standard method for grinding ore is the wet process. This is mainly due to the fact that the downstream process is wet and considering the total circuit dry grinding is not the most eco­nomical method for the comminution of the ore. Presently in gold ore processing dry grinding is only applied in cases where whole ore roasting is required downstream from the milling plant or if organic carbonaceous matters and sulfides are the primary reasons for the refractoriness. Since dry ore can be fed to the roaster, a dry grinding mill can advantageously be applied. In cases where d1y grinding could be applied advantageously for instance if the ore contains water soluble material and wet grinding is not possible there are serious concerns prevailing within the industty against this technology due to several reasons. Besides of the aspects as discussed later in this paper, there are several plants in operation with little success and considerable operational prob­lems. The reasons for this often lie in the fact that the several com­ponents of such a plant are bought from independent sources with­out considering the system requirements. It is essential that the dry grinding plants require accurate design between drying, pneumatic transport and grinding of the ore in the circuit. This paper will address some of these concerns raised in the industiy from a mill vendor's view along with discussing the development for the selection and configuration of the various dty grinding circuits.

Jan 1, 1998

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to supplement its two existing main fans. The third fan will operate in parallel with the two existing fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, NM, is a US Department of Energy (DOE), Carlsbad Area Office, facility that is designed to permanently dispose of US defense-generated transuranic waste in a deep, bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for modifying, supplementing or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel et al., 1997) to identify and quantify operational concerns, evaluate possible alternatives and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness and improving system performance. The fan installation project accommodates several operational and scheduling con¬straints. WIPP was scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP 's ability to declare facility readiness. Therefore, operational disruptions during the system tie-in had to be minimized. All engineering for the project has been com¬pleted, and physical modifications were begun in July 1997. The project was completed in 1998.

Jan 1, 2000

By Hal McVey

"Philosophy" addresses the definition and assigning of importance to the marketing of by-products. Two examples, one in metals and the other in industrial minerals, explore prime product to by-product relationships. Relative revenues from all products illustrate the importance of by-products to economic feasibility. "Mechanics" takes a broad view of the types of marketing organizations that are applicable to individual circumstances in the marketplace. In-house marketing as well as agents, merchants and trading companies are outlined and discussed. Philosophy Definition Of Terms Philosophy Definition Of Terms The definition of terns for a paper such as this is generally a necessary but not-very-interesting exercise. However, in simply trying to clearly define the term "by-product" some interesting relationships between products arise and the line of demarcation between "product" and "by-product" often becomes obscure. The search for that distinction represents the philosophy portion of the title. A couple of definitions of philosophy can even help to set the tone for what follows. According to Webster, philosophy is : 1 Pursuit of wisdom. 2. A search for a general understanding of values and reality.

Jan 1, 1983

By B. T. Mirabile, D. Tang, Y. Luo, S. S. Peng, C. T. Holland

Knowledge of local coal mine roof geology is critical to the design of a safe and suitable mine structure. An automated drill control and data collection system has been designed for a J.H. Fletcher twin-head roof bolter. Drilling parameters collected during the drilling process can be used to interpret geologic features intercepted in the mine roof. The drill and data collection system have been tested in both laboratory and underground settings. Visualization of certain drilling data has shown good correlation with geology drilled. A quantitative prediction model was developed using drilling parameters examined with data visualization. The quantitative model was tested using laboratory drilling data.

Jan 1, 2004

By John W. Brauns

18.1-RAILROAD JOHN W. BRAUNS Conventional railroad haulage can be employed at both open-pit or strip and underground mines-in the latter case, largely for transfer of ore from distant openings to processing plants, or processed material to loading points or docks, using standard hopper cars for bottom unloading or gondolas for rotary dumping. The major application, however, is in surface mining for moving ore and/or waste out of the pit to a crushing plant or dump. Consequently, the following will deal largely with this phase of railroad operation, though the conclusions apply equally, for the most part, to other rail-type surface haulage. In surface mining, trains consisting of a locomotive and gondola or side-dump cars suitable for loading by power shovels are used. Gondolas are restricted to hauling ore as a rotary dumper is required. Side-dump cars are more versatile, carrying both ore and waste, but because of their additional dumping mechanism they are likely to be more expensive to maintain.' Also they weigh up to twice a flat-bottom car of the same capacity and. therefore, fewer" cars can be hauled per train. Standard-gage track is most commonly used. Track systems incorporate low-quality temporary track where moves are frequent and permanent high-quality track on main lines. Rail haulage can be used alone, or in combination with other surface haulage methods, thus permitting a selection best adapted to the peculiar requirements of each mining project. 18.1.1---GENERAL APPLICABILITY, CONTROLLING PHYSICAL CONDITIONS For handling rough rock, the shovel-train system is unexcelled.' The ideal applica¬tion is in a large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported over 3 mi. If. in addition, a high production rate is to he maintained, railroad haulage probably will afford a lower cost per ton transported. Grade must he relatively gentle-usually 3% uphill and 4% downhill. The greater the differences in elevation involved, the greater are the track grade space requirements; for example, a 3 c ramp out of a pit only 300 ft deep is almost 2 mi long. Main-line track locations should he selected carefully so that the number of moves during the life of the mining operation can he kept to a minimum. This applies both to the ore haulageway and that for waste. Such moves are not only expensive, but are difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semipermanent trackage. Figs. 18-1 and 18-2 illustrate typical track layouts. The effect of terrain in considering railroad haulage is confined chiefly to the initial cost of the installation. Grade construction in mountainous territory is ap¬preciably more expensive. However, if that expense can be borne, the subsequent maintenance cost of trackage will not he much higher than in areas of low relief.

Jan 1, 1973

By G. M. Wali Ullah, Micah Nehring, MEHMET KIZIL, PETER KNIGHTS

In operations that use the sublevel stoping mining method, production scheduling takes into account factors — including ore reserve envelopes, ore grade averages, equipment capacity, feed controls to the mill, and geotechnical restrictions — across the scheduling horizon. Mathematical programming is one of the most effective methods for enhancing the decision-making process in regard to the most viable production schedule in light of a given set of limitations. The majority of research on sublevel stope mining focuses primarily on a single objective of optimization, which is to maximize the net present value (NPV). Environmental, social and governance (ESG) considerations are becoming more prevalent in the mining industry. This includes aspects relating to deforestation, land disturbances, gas emissions, community relations and water usage, among many others. Institutional and other kinds of investors are becoming more interested in the work that resource companies do regarding their ESG obligations. This review article identifies the gap in the existing literature and proposes to simultaneously optimize the production schedule around three objectives. Two of these relate directly to ESG aspects

Jul 1, 2024

By Y. S. Roditis

A new method for interpolating a block model is proposed, where both the diamond drill holes (DHs) and blast holes (BHs) data are used. Combining these data types poses a geostatistical "class size" problem due to the different statistical properties of the densely populated BHs and the sparsely populated DH data. This paper discusses how linear regression was used to adjust the DH values prior to the interpolation to account for the "class size" problem which is inherent to the procedure. The correlation between the BHs and the DHs is found. The DHs are then corrected based on the regression line. Each block that falls within a certain range of influence of a blast hole is assigned a different code and is interpolated with the combined BH and regressed DH data set. Blocks that fall outside the range of blast hole influence are interpolated using the original DH data set. A comparison against other methods, indicate a 12% improvement over using DHs only and a 2% improvement over using BHs only.

Jan 1, 1992

By M. G. Premo

The McKinley Mine is located in the northwest New Mexico, in McKinley County, approximately 25 miles from Gallup. The mine is operated by The Pittsburg & Midway Coal Mining Co. (P&M), a wholly owned subsidiary of the Chevron Corporation. P&M is headquartered in Englewood, Colorado. Since the McKinley Mine began operations in 1962 a total of 83,391,000 metric tons of coal have been sold through 1990. The 1991 production was approximately 5.000.000 metric tons. The mine operations are contained on a 109.000 square kilometers lease area of which 44.000 square kilometers are on the Navajo Nation. The present customer base consists of four utilities and one industrial account, all of which are located in Arizona. The utility customers are the Arizona Public Service Co. Cholla Station at Joseph City, The Salt River Project. Coronado Generating Station near Joseph City, and The Tucson Electric Company, Irvington Generating Station in Tucson. The industrial customer is the Stone Container Corporation, Snowflake Paper Mill.

Jan 1, 1992