Search Documents

By David R. Zuchelli, Elio L. . Checca

Two case studies of methane gas explosions and their effect on the operation of underground coal mines are presented. The studies detail the recovery operations and investigations at each mine site. These include the circumstances prior to the explosions and the effects on the surface and underground ventilation control systems. Various ignition sources such as surface and underground electrical power systems, degasification sites, ventilation shafts, test well casings, and lightning activity were investigated. In each case, a lightning report from the National Lightning Detection Network1 was used in conjunction with the physical evidence and eyewitness accounts to confirm lightning strikes as the ignition source for the explosions.

Jan 1, 1995

By K. V. S. Sastry

Pelletization, sintering, and pressure compaction are the most common methods used to agglomerate ore concentrates. Over the last 20 years agglomeration has grown enormously in popularity and has become a standard unit operation in the nonferrous, cement, fertilizer, and ceramic industries. However, it is in the processing of iron ores and the preparation of blast furnace feed that agglomeration is used most and its application has grown fastest (Ball, et al., 1973; and Sastry, 1977). This chapter deals with an account of the current practices and future trends in the application of computers relative to an overview of the process design and engineering considerations of the unit operation of agglomeration.

Jan 1, 1979

By Winfield G. Wright, Philip L. Verplanck, Douglas B. Yager, Dana J. Bove, M. Alisa Mast

The upper Animas River watershed is affected by metal-rich drainage from abandoned mines and by natural weathering of mineralized bedrock. To investigate the importance of natural metal sources, surface waters were sampled in a minimally mined but intensely altered area of the watershed. Water chemistry was strongly controlled by the degree of bedrock alteration. Propylitically altered rocks, which contain calcite, produced neutral waters with low metal concentrations, whereas quartz-sericite-pyrite alteration was characterized by acid-sulfate type waters with high metal concentrations. A mass-balance approach was used to estimate natural metal sources, which accounted for 56-905 of the dissolved metal load discharging from the study area

Jan 1, 2000

By Jacques Villeneuve, Stéphane Brochot, Jean-Claude Guillaneau, Marie-Véronique Durance

Since 1986, BRGM has been developing a powerful process simulation software package, USIM PAC. These last years have seen significant developments in mineral processing technologies, particularly in hydrometallurgy, bio-hydrometallurgy and mineral liberation. The new version of the simulator, USIM PAC 3.0, incorporates these modem-processing fields. Its structure and tools allow the user to take into account, at the same time, a wide range of technological, economical and environmental aspects. The improvement of the existing features and the introduction of new unit operation mathematical models and tools such as the supervisor, global optimization, workshop model or chemical reactions contribute to a global approach in mineral processing design.

Jan 1, 2002

By George W. Luxbacher

The inclusion of a new term "planned subsidence" in the Surface Mining and Reclamation Act of 1977 has lead the U.S. coal mining industry into a new aspect of engineering: subsidence planning. Subsidence planning has necessitated the integration of geotechnical, civil, and mining engineering disciplines. Although much of the foundation and application work has been completed, subsidence planning is still a developing area. This paper discusses the application of subsidence planning in several brief case studies (a high voltage transmission tower, a sewage treatment plant, and a slurry impoundment), emphasizing the risk assessment aspects necessary to account for some of the uncertainties that may exist.

Jan 1, 1986

By B. V. Driga

The paper presents the evaluation method of the thermal power potential of the salt lakes developed in collapsed salt mines in Romania. It is well-known that the hydro-chemical stratification of these lakes favors warmer internal layers. The degree of heat varies during the year, but, taking into account the large number of genetic lakes of this type, it can be used as a local utilizable power source. The authors analyze the correlations between the physico-chemical parameters of the water and the degree of heat stored as a function of the morphological parameters of the lakes, as well as the technical parameters for capitalizing on this power.

Jan 1, 2008

By William F. Stowasser

The United States has traditionally been the world's largest producer and net exporter of phosphate rock and related fertilizer products with the exception of rock exports from Morocco. In recent years, however, U.S. producers have faced increasing competition from operations in foreign countries, leaving the future position of the U.S. phosphate .industry as a leader in the world markets somewhat less certain. This paper will review the U.S. phosphate rock industry in relation to its known demonstrated reserves, its historical and present production and export levels, and its future mining potential. The paper will include an analysis of the availability of phosphate rock in the United States represented by cost-tonnage relationships. The U.S. phosphate rock industry has for decades provided raw materials at reasonable costs to the phosphate fertilizer industry, and the fertilizer products have been made available to both domestic and international markets. Natural soils normally contain low quantities of phosphorus, and cultivation exhausts the available phosphorus through the removal of harvested products. Yields diminish, and it becomes necessary to apply phosphorus to the soil in an amount at least sufficient to compensate for removal. Raising the level of phosphorus also permits nitrogen and potash fertilizer nutrients to be effective and sustain the high crop yields necessary to support increasing food demands. In only a few areas of the world are soils, climate, rainfall, and low-cost phosphate fertilizer available to assure high agricultural yields in successive years. One of these areas is the central United States and south central Canada. By contrast, in the Soviet Union, the weather conditions in farming areas frequently cause crops to either bake or drown in the field. To attempt to counter the effect of weather on production, the U.S.S.R. has increased use of fertilizer and equipment in recent years. The effect of fertilizer on various crops has been documented, and in all cases, improvements in yield and plant development were noted, as was the ability of fertilizer to mitigate the effects of unfavorable climatic conditions. Phosphate resources can be classified as either identified or undiscovered. In the identified classification, we are principally concerned with demonstrated phosphate resources, or those that have been measured or indicated. In the southeastern United States, the phosphate mining areas of Florida and the Carolinas have been explored and drilled extensively in attempts to locate new deposits. The exploration programs indicate that another Florida Bone Valley Formation or North Carolina Pamlico River Deposit is unlikely to be discovered in the southeastern U.S. coastal plain. Phosphate rock deposits of commercial interest in the western United States are located in Montana, western Wyoming, northern Utah, and southeastern Idaho. The deposits are in the Permian Phosphoria Formation with most of the mining activity occurring in Idaho. Although substantial demonstrated resources have been identified, recovery costs and the field's isolation from markets have restricted growth of the industry in the west. The phosphate rock deposits in Tennessee are well known, and it is estimated that about 29 million metric tons1 are potentially recoverable. Undiscovered deposits of brown rock in Tennessee would likely be quite small.

Jan 1, 1985

By Ehsan Alavi, Daniel Cressman, Tatiana Chiesa, Robert Mayberry

The City of Toronto’s Coxwell Bypass Tunnel (CBT) is currently being constructed by North Tunnel Constructors ULC. The scope of the CBT project includes construction of approximately 10.5 km of 6.3 meter finished diameter rock tunnel, five large diameter (20 and 22 meter) storage shafts and eleven tunnel connection drop shafts, along with associated deaeration and adit tunnels. This paper describes progress on the CBT to date and reviews the approach taken in both design and construction of the tunnels and shafts to mitigate risks and reduce cost and schedule of construction.

Jun 13, 2021

By Joshua Cole, Joshua Sovechles, Christian Cardoso, Guillermo Bermudez, Martta Hirsi, Joshua Dettamanti, Rabia Abbasi

The implementation of technological advancements in flotation is key to optimize performance in mining operations. Consequently, flotation cell’s performance is highly dependent on the effectiveness of the mixing mechanism. A more efficient flotation mixing mechanism is likely to improve metallurgical performance and optimize energy consumption, which is the motivation for Metso’s journey to develop the latest iteration of FloatForce®. Looking to test the new design at plant scale, Metso approached the Kennecott Copperton concentrator, which is continuously looking for different venues to improve metallurgical performance. In this context, a test campaign was conducted to implement this new flotation mixing mechanism in their rougher circuit during 2024. The industrial trial consisted of several sampling campaigns assessing different operational parameters for comparison purposes around a 300m3 flotation cell. The effect of the new flotation mixing mechanism on the cell’s power draw was also studied. The results of this trial at Kennecott are presented in this paper. Overall new flotation mixing mechanism, FloatForce+ was seen to perform as well as the original FloatForce.

Feb 1, 2025

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." 'If these blue sky Ph.D.'s (in the instruments and controls area within research) had some operating experience they wouldn't make a lot of the suggestions they do."

Jan 1, 1981

By Hugo E. Camargo, Amanda S. Azman, Brian Kim

Repeated noise exposure and occupational hearing loss are common health problems across industries and especially within the mining industry. Large mechanized processes, blasting, grinding, drilling, and work that is often in close quarters put many miners at an increased risk of noise overexposure. In stone, sand, and gravel mining, noise is generated from a variety of sources, depending on the type of ore being mined as well as the final consumer product provided by that mine. Depending on the source of noise generation, different strategies to reduce and avoid that noise should be implemented. The National Institute for Occupational Safety and Health (NIOSH) has evaluated the noise profile at three operational surface stone, sand, and gravel mines. A-weighted sound level meter data as well as phase array beamforming data were collected throughout the mines in areas with high noise exposure or high personnel foot or vehicle traffic. Sound level meter data collected on a grid pattern was used to develop sound profiles of the working areas. These sound contour maps as well as phase array beamforming plots were provided to the mines as well as guidance to modify work areas or personnel traffic to reduce noise exposure.

Jan 6, 2022

By T. P. Meloy

Current coal cleaning technology uses heavy media (HM) for the recovery of coal in particles larger than 1/16 of an inch. Through the use of float sink measurements of the feed and products to commercial HM unit operations, a selection function, sometimes called Tromp curve in the coal industry, can be computed. Since the selection function is a plot f the probability of a particle appearing in the float versus the particle density, the slope of the curve will be sharper at the point where the particle has a 50% chance f appearing in the float. Thus, the separation will be better. Fine-tuning a unit operation or a circuit of unit operations requires that the selection function be accurately known. By current practice, it is difficult to obtain an accurate measure of the slope because, when the selection function is plotted versus density, the data forms an S-shaped curve which lacks data points near the 505 point of the curve. This lack of sensitivity in measuring the slope means that small recovery improvements cannot be detected; thus, only large improvements are measurable. Since most engineering improvements are small when individually considered, but large when aggregated ever many small improvements, this lack of measurement sensitivity rules out the slew march toward improved efficiency. This paper presents a method of analyzing heavy media selection functions resulting in a far more effective measure of the selective function slope. Furthermore, this improved method is applied to a number of industrial coal cleaning plants for both heavy media and heavy media cyclones. Using the work of Hudy (1968), and Deurbrouck and Hudy (1972), selection functions for individual unit operations in each plant are calculated as a function f particle size as well as density.

Jan 1, 1982

By Michael von Seebach

High-pressure grinding rolls subject the feed material to pressures of 200 N/mm? During this process considerable size reduction and the Formation of flakes occur. This paper describes the basic consideration For design and operating of this type of mill. It is also shown that the particle size distribution resulting from this process is typical for grinding processes but untypical for crushing processes. High pressure grinding rolls are designed in size of up to 2.8 m roll diameter allowing feed material top sizes of 250 mm. The rigid frame, bearing and drive - train design allows a broad application of the high-pressure grinding rolls operating the machine in open or semi-closed and closed circuit for dry and moist feed materials. Operating results show that capacity increases of up to 100 % can be accomplished with this technology. The high-pressure grinding roll also, allows for lower operating and maintenance costs due to energy savings of up to 20 L and reduction of wear to less than 1 76 for dry and less than 0.1 5 for wet grinding. Other advantages of the high-pressure grinding rolls are smaller equipment sizes than a ball or SAG-mill for a given capacity resulting in lower building sizes with reduced capital in- vestment costs.

Jan 1, 1987

By M. Birdsell

"Sustainable long-term restoration requires adequate planning and preparation, implementation, and measurement goals to monitor success associated with restoring sites to pre-disturbance levels of ecological health. The Buckhorn Mountain Mine riparian habitat restoration project has been a multi-year endeavor with a variety of restoration techniques implemented by Kinross Gold/Crown Resources Corporation. INTRODUCTION The Buckhorn Mountain Mine procured mitigation lands during the permitting process to be set aside for long-term restoration. A portion of this mitigation land included three aquatic habitat mitigation parcels; a spring and wetland complex and two stream and riparian corridors. These properties were historically used for agriculture purposes and livestock grazing. During initial permitting, habitat monitoring and mitigation plans were created to help guide restoration, and provide measures for success. Various techniques and adaptations have been implemented on the properties since 2007, and continued efforts are being implemented annually to ensure the long-term success of the project. Field measurements are collected annually to ensure mitigation objectives are being met, and provide opportunity to modify restoration efforts when necessary. MATERIALS/METHODS Restoration efforts have included implementation of several methods including livestock exclusion, treatment of state and locally listed noxious weed species, installation of regionally sourced riparian plant species and local stock willow cuttings. Annual mechanical and herbicide treatments for noxious weeds have been conducted annually. Efforts to control reed canarygrass (Phalaris arundinacea) have been implemented since 2013; methods include mechanical and herbicide treatments. A combination of methods has been employed to help aid restoration of native species within the riparian corridor, and increase survival of planted species, including weed matting and browse barriers to aid riparian planting success. Instream planting of local stock willow have also been employed to increase stream vegetative cover and provide long-term bank stabilization. Most recently, a perched culvert near one of the properties has been replaced with an aquatic life passable culvert designed to aid in the upstream migration of fish species into the stream system. Efforts to provide increased fisheries into upstream portions of the system and aid in restoration of stream bed and bank have been employed to increase the ecological value downstream of the replacement. In addition to efforts completed by the client to provide restoration efforts, a local non-profit organization, in conjunction with the client, installed beaver dam analogues (BDAs) in the fall of 2014. These structures are intended to raise water levels along stretches of incised channel in an attempt to flood historic off-channel floodplain"

Jan 1, 2016

By S. C. Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by U.S. Department of Energy, designed to demonstrate the safe containment for disposal of radioactive waste. A mine (repository) is currently being developed 2150 feet below the surface, in a thick salt bed which will serve as the disposal medium. Provision of a proper ventilation system at the WIPP Project is a major priority of those responsible for its design, management, and operations. As an ongoing effort towards this goal, it was decided to simulate the mine's ventilation system using Dravo's MINEVENT computer program. Specifically, the work included the development of the following simulation models: 1. Simulation of the current ventilation system 2. Simulation of the designed ventilation system for the following modes: o Mine Construction mode/shift o Waste storage mode/shift o Fire or exhaust filtration mode These computer models are useful in solving complex ventilation problems likely to be encountered in an R&D project, like WIPP. They are particularly helpful for the development of contingency plans to incorporate during emergency situations, such as fires, fan stop- pages, radiation leaks, etc. Also, they can be utilized when considering expanding certain underground areas to ensure the availability of adequate ventilation.

Jan 1, 1986

By Elgin D. Bell

Within the next, year or two, Western Canada should overtake Mexico and France. to become the worlds second largest producer of elemental sulphur, surpassed only by the United States, By 1965, it should produce about 25% of the world's total elemental production and, about 10% of sulphur produced in all forms. In 1952 Alberta had but one small sulphur recovery plant. By 1962, it had fifteen plants with a total designed capacity of almost 6,000 long tons of sulphur per day and actual production of almost one million long tons per year. This decade of dynamic growth was the result of Alberta's rapidly developing natural gas industry. More particularly it was the result of approval in 1960 to export natural gas in large volumes into the United States. Prior approval to export gas from Alberta to eastern Canada and relatively modest volumes to the U. S. had resulted in the construction of several plants but none were of the scale required to serve the U. S. market.

Jan 1, 1963

By R. V. Stewart

This chrysotile asbestos orebody is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 mi) north of Montreal; 480 km (300 mi) north of the tree line and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1/4 mi) in length some 61 m (200 ft) in width and plunges at 25-30 below surface to a vertical depth of at least 610 m (2000 ft). The orebody was originally evaluated by programs of surface mapping, diamond drilling and bulk sampling. The fibre is semi-crude, possesses excellent strength, and good fibre length distribution.

Jan 1, 1978

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By H. M. Breza

Recovery of phosphate concentrate has received increased attention as the existing mine and plant production capacity limitations of the Texasgulf Inc. Aurora, North Carolina Mine are reached. Improved mining techniques and mineral processing of waste streams offer a potential to increase overall phosphate production without major expansion of the Mining facility. Innovative processes have been or are being identified to maximize pit mining recovery and to minimize losses in waste streams, resulting in more effective use of the valuable phosphate natural resource. This paper will describe the various continuous recovery improvement programs being implemented to achieve this goal.

Jan 1, 1994

Samples collected during the exploration phase of mining represent baseline conditions at the site. As such, they can be very important in forecasting potential environmental impacts should mining proceed, and can become measurements against which future changes are compared. Constituents in stream water draining mined and mineralized areas tend to be geochemically, spatially, and temporally variable, which presents challenges in collecting both exploration and baseline water-quality samples. Because short-term (daily) variations can complicate long-term trends, it is important to consider recent findings concerning geochemical variability of stream-water constituents at short-term timescales in designing sampling plans. Also, adequate water-quality information is key to forecasting potential ecological impacts from mining. Therefore, it is useful to collect baseline water samples adequate for geochemical and toxicological modeling. This requires complete chemical analyses of dissolved constituents that include major and minor chemical elements as well as physicochemical properties (including pH, specific conductance, dissolved oxygen) and dissolved organic carbon. Applying chemical-equilibrium and appropriate toxicological models to water-quality information leads to an understanding of the speciation, transport, sequestration, bioavailability, and aquatic toxicity of potential contaminants. Insights gained from geochemical and toxicological modeling of water-quality data can be used to design appropriate mitigation and for economic planning for future mining activities.

Jan 1, 2011