Search Documents

By W. Petruk

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections in order to characterize a mill product and to determine the apparent mineral liberation. It was found that a representive polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly individual screened' fractions are not representative of the sample because minerals are partitioned during screening. Consequently the quantities of soft brittle minerals are increased in fine grained fractions and quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (1 Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analysing each fraction and combining the data. Somewhat less accurate data would be obtained by analysing a series of screened, fractions that have a wider size range of particles (5 Tyler size ranges). Mineral liberation analyses show that the most reliable apparent mineral liberation in each screened fraction is a value taken from a smooth curve drawn through the lowest points on a graph of % free vs size. A correlation between the apparent mineral liberation in screened fractions and calculated mineral liberations using Kings liberation model is good for sphalerite but not for chalcopyrite and galena.

Jan 1, 1985

By W. W. Dudley

The U.S. Geological Survey, in support of underground testing of nuclear explosives, has developed a technique (Dudley, 1910) to predict the inflow of ground water to large underground chambers that are cylindrical in shape. By treating the chamber as a large-diameter well pumped at constant drawdown, the nonsteady discharge can be computed by the method of Hantush (1961) for analyzing flowing wells under leaky artesian conditions. In mining applications, whether for mineral recovery or for nuclear testing, the most serious departure from the conditions of Hantush's model results from the gradual enlargement of the opening under drained conditions. Inherent in the analytical technique is that the "well" is fully completed at the time that dewatering begins. Because safety is the prime concern, however, initial pumping systems or personnel evacuation procedures must be designed to handle the greatest conceivable inflow. DEFINITIONS Because somewhat different meanings are attached to similar words in different technical fields, the U.S. Geological Survey definitions (Lohman, 1970) of several hydrologic terms used in this report are given below. An aquifer is a formation, group of formations, or part of a formation that contains sufficient saturated permeable material to yield significant quantities of water to wells, and springs. A confining bed is a body of material lying stratigraphically adjacent to one or more aquifers and having a hydraulic conductivity distinctly lower than that of the aquifer. The total head (dimensions L) of a liquid at a given point is the sum of three components: (1) elevation head, he, which is equal to the elevation of the point above a datum; (2) pressure head, hp, which is the height of a column of static water that can be supported by the static pressure at the point; and (3) velocity head, hv, which is the height the kinetic energy of the liquid is

Jan 1, 1971

By Akram Marseet, Andrew J. Petruska, Rik Banerjee

Underground mine roof bolting is a crucial operation for miners’ safety and mine sustainability. Since roof bolting is a manual or human-supervised operation, miners’ safety is at risk due to dust or rock falls. Traditional machine learning algorithms have shown limitations to detecting drillable areas, mainly due to harsh lighting conditions. The authors propose an adaptive deep-learning framework for autonomous roof bolting. The proposed framework is based on implementing a binary semantic segmentation algorithm on color images to classify pixels that belong to rock from those that belong to non-rock. Significantly, the proposed framework implements deep learning semantic segmentation on images from traditional and neuromorphic vision sensors in underground mines. The performance of the proposed model shows an impressive accuracy level of at least 98% at a low number of training epochs with smooth learning curves. The high accuracy enables the implementation of autonomous roof bolting, greatly improving miners’ safety and operational efficiency while reducing human exposure to safety hazards. This research will advance the use of deep learning in mining automation and has the potential to revolutionize the traditional mining industry.

Feb 1, 2024

By Mike Harrington, Tung Vu

The Regional Connector Transit Project is a 1.9-mile-long underground light rail system that will connect LA Metro’s A (Blue), E (Expo), and L (Gold) Lines in downtown Los Angeles. This $1.75-billion design-build project is scheduled for revenue service in Spring 2023. The project consists of 21-foot diameter twin-bored tunnels, a 300-footlong crossover SEM cavern, three new underground stations (at 1st Street/Central Avenue, 2nd Street/ Broadway Avenue, and 2nd/Hope Streets), and cut-and-cover tunnels along South Flower, Alameda, and 1st Streets. This paper, which is the continuation of our previous paper presented in RETC 2019—LA Metro Regional Connector Transit Project: Successful Halfway-Through Completion, will provide insight regarding the construction of major components, and the system integration and testing work undertaken for this complex transit project.

Jun 13, 2023

By Bernard F. Anderson

INTRODUCTION In this chapter, the term "down-the-hole drill" (DTH drill) is used as a generic name that encompasses the various trade names and other references such as "downhole drill," "in-the-hole drill," etc. This chapter is limited to a description of DTH drills used in stoping large underground ore bodies. DTH drills differ from conventional drills by virtue of the placement of the drill in the drill string. The DTH drill follows immediately behind the bit into the hole, rather than remaining on the feed as with ordinary drifters. Thus, no energy is dissipated through the steel or couplings, and the penetration rate is nearly constant, regardless of the depth of the hole. Since the drill must operate on compressed air and tolerates only small amounts of water, cuttings are flushed either by air with water-mist injection or by standard mine air with a dust collector at the collar. HISTORICAL DEVELOPMENT Mine managers have long known the economies enjoyed by quarry and open-pit operators in producing large quantities of ore. The savings are due primarily to the availability of massive equipment, capable of drilling large blastholes to reduce the amount of drilling, increase the fragmentation, reduce secondary blasting, and im¬prove the flow of the product. In an attempt to reduce underground mining costs, various methods are used for long-hole drilling, includ¬ing standard pneumatic percussion drifters and diamond drills. These systems have their shortcomings; percus¬sion drills are limited to small hole sizes and they ex¬perience excessive deviation and significant loss of energy with increased depth. The diamond drills provide deeper and straighter holes, but only at high cost. Both systems suffer from high noise levels, low penetration rates, and poor explosives distribution, among other problems. When the mining companies approached the drill manufacturers for a compact and portable large-hole jumbo for underground use, they specified not more than 1 % deviation on 60 m (200 ft) of vertical hole and a penetration rate of 15 m/h (50 fph). On Dec. 23, 1960, a test unit was placed in service in Montana and met the performance criteria. Though lacking the so¬phisticated features available today, the economies of surface blasting were brought underground. Unfortunately, the first system did not gain immedi¬ate acceptance in the industry. Among the factors con¬tributing to its demise were resistance to change, the need to alter development methods for the ore bodies, and a lack of flexibility in moving the rig from setup to setup and from level to level. In 1972, the mining industry again challenged the drill manufacturers to provide a workable jumbo that would combine compactness, ease of maintenance, relia¬bility, and efficiency, all on a self-propelled chassis. The manufacturers responded by providing improved jumbos, which have been accepted with enthusiasm throughout the mining industry. Today's DTH jumbos are capable of drilling from 100 to 200 mm (4 to 8 in.) diam holes that can be reamed to even larger diameters. The holes can be drilled to depths of 150 m (500 ft), depending upon ground conditions and the capability of the jumbo to retrieve the steel and drill. Fig. 1 illustrates a typical DTH jumbo. APPLICATIONS The uses to which DTH drill jumbos have been put are quite numerous, with new uses being found regularly. For convenience, these uses may be classified as primary blastholes and nonblasting holes. Primary Blastholes The original purpose for the development of the DTH jumbo was for drilling primary blastholes that could be mined by open-stope methods. Prior to the advent of the DTH jumbo, extensive development was required before production drilling could begin. Sub¬levels were required to allow access for column-and-arm stopers or ring/fan jumbos, to the extent necessary based on the effective penetration of the chosen machine. With the DTH jumbo, the mine engineer is able to reduce preproduction time and development costs. How¬ever, the most significant saving results from an im¬proved cost per ton of broken ore in the production phase. To utilize a DTH system, only a top heading and drawpoints are necessary. The top heading can be the width of the ore body with a 3.7-m (12-ft) back. A drop-raise pattern is drilled and shot to begin the stoping operation, providing a free face for subsequent blasting. A typical layout is illustrated in Fig. 2. The advantages of this system include: 1) Drilling and blasting are independent operations, and blasting can be performed at a rate congruous with the mine's ton-per-day capacity. 2) The development layout is simplified. 3) Good explosive distribution is achieved, provid¬ing more uniform fragmentation. 4) Environmental conditions for operators are im¬proved, including improved safety with all work directed downward (not overhead), lower noise levels, little fog, and a reduced dust count. 5) Improved production per manshift. 6) Simplified and easier operator work cycles. 7) Reduced cost per ton of product. 8) Fewer holes lost due to ground shifts. Nonblasting Holes With the introduction of the compact DTH jumbos, other practical uses became apparent, including the drilling of: 1) Holes for sand fill, from level to level and from level to stope. 2) Drain and dewatering holes. 3) Power and communications cable holes.

Jan 1, 1982

By A. Haile, A. Poole

During 2001-2002, the Granny Smith Mine of Western Australia undertook the development of a planned circular failure. Excavation took place in an interim pit wall that intersected the transported sediments, lake clays, and palaeo channel sands that overlay the deposit. The purpose of the study was to refine feasibility level slope parameters used for the initial design of the Wallaby pit, with the intent of increasing the overall slope when excavating the ultimate pit limits. During excavation, the geological and hydrogeological characteristics were studied in detail and data was collected using area-specific instrumentation and monitoring. Failure occurred in mid February 2002, at which time a detailed survey of the excavated slope using laser technology was conducted to provide geometric information suitable for back analysis of the material shear strength. The slope failure and associated information was analysed by geotechnical consultants. The revised shear strength and hydrogeological parameters were then applied to design the final pit walls. The slope redesign provided a cost saving of approximately seven hundred thousand US dollars. Design, slope formation, back analysis, the geology of the clay units, the hydrological environment, planned infrastructure, management and safety issues, and the on-going slope performance of the final slope are discussed.

Jan 1, 2004

By T. Yue, Z. Gao, X. Tong, R. Liu

"Lead ions (lead nitrate) were introduced to modify the surface properties of scheelite, effectively and selectively improving the flotability of scheelite, with benzohydroxamic acid (BHA) serving as the collector. A series of experiments about the mode of addition and the ratio of lead ion to BHA were conducted and indicated Pb-BHA complexes were the active species responsible for the flotation. And two adsorption models of BHA on the surface of scheelite were established. For both the two adding methods, some kind of complexes formed by lead ions and BHA played a key role in the flotation process. Zeta potential, FTIR, and XPS studies indicated that the adsorption amount and intensity of BHA on the surface of scheetlie were larger by adding the reagents as a mixture. The mixed addition is conducive to form Pb-BHA complexes and improve the adsorption efficiency of BHA on the surface of scheelite, as well as the recovery of scheelite. INTRODUCTION Scheelite, as an important tungsten-bearing mineral, is nowadays utilized mainly by flotation (YIN and WANG, 2014; Sun et al., 2011; Gao et al., 2015; Gao et al., 2015). Flotation separation of scheelite from calcium minerals creates difficulties because of the existence of the same cation in the minerals and similar physico-chemical characteristics such as solubility, hardness, specific gravity, point of zero charge (PZC), etc. (Arnold and Warren, 1974; Deng et al., 2016; Deng et al., 2015; Ozcan and Bulutcu, 1993a; Yongxin and Changgen, 1983). The conventional collectors used in the flotation of scheelite ores are generally fatty acids or fatty acid derivatives (Bo et al., 2015; Oliveira and Sampaio, 1988; Shi et al., 2014; Sivamohan, 1988; Yongxin and Changgen, 1983). It is difficult to separate scheelite, especially from calcite, with these reagents because the adsorption mechanism of these collectors occurs through chemisorption of the oleate ion onto the mineral surface (Atademir et al., 1979; Changgen and Yongxin, 1983; Hiçyìlmaz et al., 1993; Hu et al., 2011). Therefore, it is almost impossible to separate them by fatty acid flotation without using any selective depressant. Although oleoyl sarcosine was used as a selective collector in the flotation of fluorite and siliceous scheelite ores (Ozcan and Bulutcu, 1993b; Ozcan et al., 1994), this selectivity is inadequate for a low-grade calcitic scheelite ore. Unfortunately, reagents such as organic colloids (dextrine, starch), quebracho, sodium phosphates, sodium silicate solutions containing polyvalent cations (hydrosols), etc. (Bo et al., 2015; Schubert et al., 1990; Shi et al., 2014; Yongxin and Changgen, 1983), used for calcite depression also depress scheelite to a large extent. Cationic collectors, such as amine and quarternary ammonium (Yang et al., 2015) and collector mixture (Gao et al., 2015) have been used to improve the scheelite flotation. However they have not been applied in industry due to the poor separation from silicate minerals."

Jan 1, 2017

By W. K. Dressel

Over 2 million tons of steel furnace dusts are produced each year in the United States. Recycling of these dusts rather than disposal would conserve mineral resources, reduce land requirements for disposal, and decrease pollution. In addition to the iron content, the dusts contain appreciable amounts of zinc and lead. Removal of lead and zinc with simultaneous reduction of Iron oxide has been achieved by inert atmosphere roasting of carbon-containing pellets prepared from steel furnace wastes. High- and low-carbon wastes were blended to obtain mixtures with sufficient carbon to serve as a reductant during subsequent roasting. The mixtures were pelletized with the addition of bentonite and water, and the dried pellets were roasted in a stream of nitrogen at temperatures ranging from 900" to 1,150° C. Zinc and lead contents were reduced to the 0.1 percent level or less by roasting mixtures containing as little as 7 percent carbon for 1 hour at 1,100° C. ton metallization increases with available carbon content; 50 percent metallization is achieved with 7 percent carbon, 85 percent metallization with 12.5 percent carbon, and over 95 percent metallization when the pelletized mixtures contained in excess of 20 percent carbon.

Jan 1, 1973

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By J. P. Earnhardt

Recycling of such municipal solid wastes as glass containers, metal cans, and newspapers has received increasing attention recently. However, municipal solid wastes account for only 1% of the total solid waste stream in the United States. The remainder includes hazardous and non-hazardous industrial wastes. Generators of industrial wastes are facing higher landfill costs. Future liability potential, and public image concerns which are forcing them to seek innovative and often profitable solutions to minimize, reuse, and recycle their waste streams. Opportunities for the mining industry in industrial recycling include recovery of mining wastes and by-products, and utilization of mineral products for treating waste streams.

Jan 1, 1993

By B. Hagemeyer

The trend to higher solids paper coating and to neutral/alkaline papermaking is causing an above average growth in the use of calcium carbonate as both a paper coating and a paper filling pigment. These developments are expected to continue well into the 1990s. Thus, calcium carbonate will account for a somewhat larger percentage of total paper pigment volume. Nevertheless, overall growth in paper tonnage coupled with an increase in filler pigment percentages will create a demand for larger quantities of other pigments as well. Kaolin will continue to be the dominant paper pigment by far, with continued growth though at a somewhat slower rate than calcium carbonate.

Jan 1, 1986

By C. H. Grant

The Dew Chemical Company has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which Dow is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of non-metallized explosives currently being used. Early in 1960, we acquired additional patent rights from independent inventors and decided to set up a development station at Virginia, Minnesota, to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the bore holes. Due to the complexities involved in controlling the manufacture of the explosive in the bore hole, performance was sometimes in doubt. Furthermore, our experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation, and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over two thousand charges of eight to 60 pounds under water and in taconites and granites with many types of explosives, we have developed a metallized explosive which is now being manufactured at a pilot plant in Virginia, Minnesota, and is being evaluated commercially.

Jan 1, 1963

By R. M. Barker

The historic Getchell property is currently being mined from the Getchell Main Underground workings, a foot wall extension of the Getchell open pit deposits along the Getchell fault. Drift-and-fill techniques are used to extract the ore through a ramp access. The adjacent Turquoise Ridge deposit is currently under development via two vertical shafts. Together, the two mines will continue to provide feed to the Getchell's 3,200 tpd mill/autoclave circuit, taking Getchell Gold from its current production rate of 200,000 ounces (Au) per annum, to over 400,000 ounces (Au) per annum by 1999.

Jan 1, 1997

By M. Tamlin

The state of the lithium mineral industry is closely linked to the performance of the glass and ceramic industries and to the overall economy. Demand for the glass/ceramic products in Europe, Asia and North America remained strong during 1999. This was due to a slight improvement in the economy during the latter half of the year. Consequently, demand for lithium minerals was firm, with a positive outlook. The major economic minerals for lithium are spodumene, petalite and lepidolite. The latter was once the primary mineral. But its importance hasdeclined since the 1960s. The lithium industry consists of two different segments: •The lithium minerals segment mines from hard-rock deposits and physically processes the material to high-grade concentrates. •The lithium chemicals and metal industry segment. The major feedstock for specialty lithium chemicals was previously high-grade spodumene ore converted to lithium carbonate. However, most lithium carbonate is now sourced from salars in North and South America.

Jan 1, 2000

By M. Ishaq, J. Rosami, J. Brune, E. Sidrow, C. Tsai, S. Slouka

Respirable rock dust poses serious long-term health effects to workers in mining and tunneling underground hard rock environments. When inhaled, respirable silica particles commonly found in quartz and other minerals will scar sensitive lung tissue and cause irreversible lung diseases. Characteristics such as concentration, type of mineral, particle size, and particle shape inhaled can harm workers to various extents. Therefore, this study characterizes rock dust particles less than 100µm in aerodynamic diameter that are released from cutting hard rock in the underground mining environment. In this study, laboratory full scale cutting tests on samples of potash rock were performed with radial picks to generate dust. Three stages of pick wear were tested: new, moderately worn, and severely worn. Comparisons between different stages of pick wear to dust concentration, size distribution, and particle shape characteristics are drawn from this study to start determining the scenarios when the released airborne dusts become potentially most hazardous for workers. Although further testing needs to be conducted to make viable conclusions, the moderately worn pick, or the pick with the most blunt tip, in these experiments are potentially the most dangerous. The blunt pick tip released the highest concentration of dust and generated particle shapes with the highest aspect ratio compared to the other two picks. The preliminary results of this study allow for the further development of optimum bit management and maintenance systems to control the exposure of respirable dust to mine workers.

Mar 2, 2022

By Arthur P. Chaves, John A. Meech, Vanessa M. Torres

Process choice for a refractory gold ore can become a controversial issue, especially at the early stages of a project. This happens since at preliminary stages, a simple economic comparison among the main process options is not possible as the differences are usually smaller than the precision of estimates. This paper presents a methodology to assess the suitability of each available technologies using a heuristic approach, were technical, economic, operational and environmental aspects are taken into account using a neural network methodology. This methodology is embedded in an expert system for gold ore process design, Intelligold, which is in the final stages of development.

Jan 1, 2000

By K. Valta

This paper presents an approach for developing a Sustainable Development Indicators (SDIs) framework tailored to the Greek Industrial Minerals sector, due to its importance for the national economy. To achieve this goal, an overview of the Greek mining and minerals, and especially the Industrial Minerals sector, from a technological and a financial perspective, is presented. In addition, a brief description of the global initiatives to this direction is given. The proposed indicators are based on those presented in 2006 by the Greek Mining Enterprises Association (GMEA) adjusted for the sector of industrial minerals by taking into account economic, environmental and social issues, known as the Triple Bottom Line (TBL) approach.

Jan 1, 2007

By Hayward B. Oblad, Anthony G. Fonseca

Coal flotation has been practiced since about 1920 in Europe and since about 1926 in the U.S. Over 200 U.S. coal preparation plants now use the process to recover coal. Over the 60 year period, the fundamental principles upon which flotation is based have been enumerated, but the interaction between the parameters that affect flotation has not been quantified and a useful model which accounts for these parameters has not yet been developed. A comprehensive and user friendly kinetic model coupled with better process monitoring and control instrumentation would allow plant operating personnel to better predict flotation performance and better control the flotation process in coal preparation plants.

Jan 1, 1989

By Gabriel Babut, Ion Matei, Roland Moraru

Several controlled recirculation systems are in operation wor1dwide. As an unconventional technique of ventilation the implementation of such a system requires particular safety conditions and a well-founded set of feasibility factors and parameters. On the other hand, many mines in Romania are facing problemms in meeting the growing ventilation demands, so that controlled air recirculation could give an answer. The present paper presents the results of the work in this field, based on a detailed theoretical approach. Parameters wich must to be taken into account were identified and analysed, numerical simulation are carried out and an experimental test-scale model is presented.

Jan 1, 1997

By A. I. Arol, I. Iwasaki

Clay minerals adversely affect the selective flocculation of iron ores. The effect of montmorillonite on a hematite-quartz mixture was studied. Montmorillonite, particularly in the presence of Ca++, caused indiscriminate dispersion of the pulp. Three possible mechanisms were postulated, namely, card-house structure formation, adsorption of dissolved species from montmorillonite, and montmorillonite- hematite interaction. It was determined that hetero- coagulation of montmorillonite on hematite was responsible for the behavior. Flocculation tests, montmorillonite abstraction tests, starch adsorption tests, zeta potential measurements, and surface analysis techniques were used to ascertain the montmorillonite-hematite interaction and to account for the manner in which it affected selective flocculation.

Jan 1, 1987