Search Documents

By J. D. Miller

The recent non-equilibrium electro-phoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by hetero-coagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. However, the nature of the inter-particle forces responsible for hetero-coagulation of such oppositely charged particles at high ionic strengths remains to be determined. In this regard, atomic force microscopy was used for inter-particle force measurements at high ionic strengths. Model systems such as polystyrene/quartz and silica/sapphire were studied to measure the particle interaction forces prevalent at high ionic strengths. Results from this study indicate that while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions. The repulsive forces between similarly charged hydrophilic surfaces at high ionic strengths (2-4 M) are described by a double exponential function with decay lengths of 0.17 and 1.4 nm depending upon the surfaces involved. On the other hand, attractive forces were observed between oppositely charged hydrophilic surfaces at high ionic strengths (2-4M) and were described by a single exponential function with decay lengths of up to 9 nm depending upon the surfaces involved.

Jan 1, 1996

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

Rendering a solid hydrophobic and solid-fluid particle* attachment in flotation are recognized as not necessarily related (1,2). The attachment is governed by forces of attraction and repulsion which need to be considered. The induction time required for attachment after solid and fluid particle are brought into proximity (3-8) illustrates the point. Laskowski(8) showed that a reduced induction time favoured flotation but detected no change in contact angle, a standard indication of solid surface hydrophobicity. Induction .time is observed in fluid-fluid particle coalescence, there being called a rest time (9-11) The induction time phenomenon is related to the presence of a metastable liquid film (disjoining film (2)) of the continuous phase (water in flotation) which must thin and rupture to permit attachment. The lifetime of this film, which is governed by the rate of thinning and the probability of rupture with thicknesss, depends on a complex interaction of forces. Investigating these forces should help clarify the attachment process. Practical benefits would be improved understanding of slimes flotation (12,13) This paper is concerned with the role of the mobile fluid particle-water interface on the film lifetime, in particular, the role of time-dependent or dynamic interfacial properties resulting from deformation of this interface.

Jan 1, 1975

By Gürkan Bacak

Study area is located on the NorthWestern of Yatagan-Yenikoy and placed in the units of the crystaline Menderes massif of Eagen, Turkey. Stratigraphically gneissic, migmatitic and metagranitic rocks are found at the base. Garnet schists, phyllitic rocks lie unconfirmitelly upon the basement rocks. Permian aged marbles can be observed as diferrent sized lenses within the schists. Triassic, Jurassic and Cretaceous aged gray colored dolomites and pure crystaline calcite bearing marbles lie upon the Permian aged schists. Neogen series, mainly composed of conglomerates, claystones, marl and limestones unconformly cover the other basement series, mentioned above. Pure calcite bearing marble occurances are found at 2 locations in the study area. These are known as Berber Quarry and Kavuk Quarry. Samples numbered as N7, N8, NA from the Berber Quarry, mineralogically composed of Calcite (97-99%)+iron oxide (1-3%) and chemically contain CaCO3 (97,98%), Fe2O3 (0.5-1%), SiO2 (0.025%) N9 and N10, sampled from the Kavuk Quarry-mineralogically composed of Calcite (94,95%)+iron oxide (2-3%)+albite-Quartz (1-2%) and chemically contain CaCO3 (92-93%), SiO2 1.49%, Fe2O3 0.42%. Especially in plastic and paint sector albite and quartz are unwilling minerals due to their hardness. Approximatelly 1/20 of the study area (87.500 km2) contains industrial calcite occurances. Moreover about 100 billion Tons geological, 1.86 billion tons runable (possible) calcite reserve calculated. It can be expected the calcite quality will be increased with depth. During the running stage of the quarries over burden removel and hand sorting processes will positive affect of the quality.

Jan 1, 2005

By Slavoljub D. Maksimovic, Steve J. Page

The Bureau of Mines measured respirable dust emission rates from overburden drilling at a surface coal mine and the transport of this dust to downwind locations. The emission rates were estimated by using multiple gravimetric dust samplers mounted on a cross-shaped tripod located immediately downwind of the drill. The transport of this dust was measured at more distant downwind locations by a combination of respirable gravimetric sampling and integrated bag sampling of sulfur hexafluoride (SF6), which was used as a tracer gas. Two modes of sampling were used: (1) At five sampling locations arranged in a semicircle around the drill. The radius of this arc ranged from 15.85 m (52 ft) to 71.32 m (234 ft). (2) In-line sampling at downwind locations with samplers located at intervals of either 10.67 m (35 ft) or 15.24 m (50 ft) for a total distance of 76.20 m (250 ft). Samples were taken 1 .22 m to 1.52 m (4 to 5 ft) above ground level. Test results for the semicircular test arrangements showed that at any downwind location, the maximum contribution of respirable dust due specifically to the drilling operation was 42%; the average for eight tests was 13.6%. In general, there was no correlation between the downwind distance of this maximum contribution and the maximum contribution itself because of changing wind direction. Test results for the in-line arrangements indicated that the transport of the dust from the drilling operation usually decreases rapidly with distance and that, even though the drill dust may produce significant health hazards for the drill operator and drill helper (or other personnel in the immediate vicinity), the exposure of downwind personnel to drill-generated dust may not be a significant problem.

Jan 1, 1987

By Wei Bin, Liu Zhe, Liping Xiao, Jichi Bai

The Acid Mine Drainage has characteristics of low pH, high concentrations of heavy metal ions, such as Fe2+, Mn2+, Cu2+ and Zn2+. In this paper, the composite particles that consisted of bentonite and steel slags were used to dispose the Acid Mine Drainage. Bentonite is the mineral materials and can adsorb heavy metal ions excellently. The steel slags are alkaline and industrial solid waste for the treatment of the Acid Mine Drainage. The main influencing factors, such as adsorbent dosages, shaking rates, concentrations of heavy metal ions, temperatures, adsorption time and pH value were studied by the static experiment. Increasing the adsorbent dosages and the concentrations of the heavy metal ions, speeding up the shaking rates, raising the temperatures, extending the adsorption time and improving pH would improve the removal efficiencies of heavy metal ions. Through considering the removal efficiencies and the treatment costs, the optimum reaction conditions for the four kinds of heavy metal ions were obtained. The adsorbent dosage 21 mg/L, the rotational speed 120 r / min, the temperature 25?, adsorption time 100 min and the initial wastewater pH 7. The four kinds of heavy metal ions existed independently in the simulated mine wastewater. The highest initial concentrations of Fe2+, Mn2+, Cu2+ and Zn2+ were 150 mg/L, 100 mg/L, 170 mg/L and 140 mg/L respectively. The removal rates were 93.42%, 92.64%, 93.86% and 95.17% respectively. The determination of the particles’ SEM-EDS Microscopic characterization showed the composite particles could play a part in neutralizing, absorbing and the chemical precipitation. The acidity decreased notably and the heavy metal ions of Fe2+, Mn2+, Cu2+ and Zn2+were adsorbed and precipitated effectively. The research results can extend the practical engineering application of the composite particles.

Jan 1, 2017

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991

By Robert D. Harris

In 1958, the coal industry, through Bituminous Coal Research, Inc., and the electric utility industry, through the Edison Electric Institute and the Association of Edison Illuminating Companies, initiated a joint program to study coal pyrite and its removal as a means of lowering the sulfur content of steam coals. It was assumed that significant amounts of pyrite often remained in washed steam coal not because available systems for coal cleaning were inadequate, but because the pyrite was small and widely disseminated, During the first two years, samples of coal were examined petrographically to determine the size, association, and mode of occurrence of the pyrite in the raw coal and in the products of laboratory separation, Samples of coal were also pulverized in different equipment to determine how effectively pyrite was released by pulverization and if the mode of pulverization affected the liberation of pyrite. From these studies, the following tentative conclusions were made (1 ): 1. Much of the coal pyrite is within a 250-70 micron size range, and therefore is too small to be removed by conventional coal cleaning, but relatively large when compared to the size of coal as pulverized for combustion in large boilers. 2. The degree of pyrite liberation is mainly determined by the size of the product and not by the type of crusher. 3. For improved pyrite removal, the coal should be cleaned during or after pulverization at the power station.

Jan 1, 1965

By Rao Balusu, Bharath Belle, Krishna Tanguturi

A collaborative research project is undertaken by Anglo American Coal and CSIRO to develop appropriate strategies for gas and spontaneous combustion management of longer panels. Extensive computational fluid dynamics (CFD) modelling studies have been conducted and calibrated using operational longwall goaf gas data to obtain a fundamental understanding of goaf gas flow patterns in longwall panels of 1.0-km and 3.0-km lengths and a detailed investigation of the effect of various mining and operational parameters on goaf gas flow patterns. The modelling studies have also been used to investigate the performance of various gas drainage and proactive inertisation strategies during various stages of longwall panel extraction. Simulation results indicated that apart from tailgate (TG) side goaf holes, gas drainage from maingate (MG) goaf holes and the mid panel start-up goaf holes would be useful for flat seam field conditions. Operation of 8–10 goaf holes is recommended for field site conditions with high goaf gas emissions of 6000 L/s. The modelling results indicated that the traditional inert gas flow rate of 500 L/s currently used in some mines would be insufficient to achieve effective goaf inertisation in long panels. Results indicate that 3.0- km-long panels would require 1500 L/s of inert gas and there is a need for multi-point inert gas injection strategy for effective goaf inertisation. In this paper, details and results of modelling investigations and recommended strategies for gas and spontaneous combustion management in 1.0-km- and 3.0-km-long panels are presented.

By William N. Poundstone

Consolidation Coal Company, through the mining research division of Continental Oil Company, is now undertaking the installation of a full-scale hydraulic transportation system to carry coarse coal from the mine face to the preparation plant. The facility will include all elements of a fully integrated haulage system including face haulage for both longwall and continuous miner sections, multiple slurry feeds, hydraulic hoisting and 2.4 miles of overland slurry transport. This undertaking is a result of more than six years of extensive research and testing, some of which has been previously releasted to the literature. To provide a reference framework for system description, a brief history of recent coal mining technological developments will be discussed. Following World War II, mechanization resulted in mining machines that were bigger, faster, more powerful, and more reliable. These changes were essentially refinements in an established mining system. They made mining more efficient than before, but they did not change the system itself. By about the mid-1960's, it was apparent that further improvements in the extraction machinery would have a declining payoff, simply because .the worst bottlenecks were in other components of the mining system. A modern continuous miner cannot be run continuously because other operations underground cannot keep pace. In fact, most continuous miners today run at less than 20% of capacity. Consequently, in 1969 Consol and its parent company, Continental Oil, undertook a long-range R&D program to try to change the basic haulage system for the better. Most coal at present is removed from the mine by a hand-off system in which the coal is transferred from the continuous miner to a shuttle car, often with the aid of a separate loader; then from the shuttle car to a system of conveyor belts; and finally from the conveyors to rail cars. The system involves a large amount of moving equipment underground, many transfer points, and the everpresent chance of operational delays and safety hazards. By removing the haulage bottleneck, we believe we can speed up underground operations substantially; and perhaps more important, we could make it feasible to develop a whole new generation of mining equipment that is inherently safer. What we wanted was a truly flexible, continuous haulage system with inherent safety advantages. Ideally the system had to meet three major requirements: First, the coal had to enter the transport system at the face, and remain in that same system all the way to the preparation plant. Second, the system had to be flexible and extensible so that it could- follow the mining machine as it advances and retracts. And, third, the system must be inherently safer than current haulage technology.

Jan 1, 1977

By G. A. Gordon

For the purpose of examining a specific problem, it is important that we look at the context, to obtain an appreciation of the general area of which the particular problem forms a part. It is my task today to speak on a particular relationship between the nations of Canada and the United States of America. What is the background? Almost two hundred years ago we both belonged to a family of nations -- the British Empire. There was a serious family quarrel in 1776 and the United States left the family and set out to make its own independent way in the world. Canada, which was not as grown up as the united States, remained with the mother country, and in 1812 resisted a vigorous attempt by the United States to get it to leave home too. With the passing of the years the bitterness of that family quarrel has faded and, aside from occasional differences, we have been getting along very well ever since.

Jan 1, 1962

By U. Thorley

Management of mine and tailings reclamation activities by surface mining oil sands operations in Alberta, Canada is experiencing increased national and international attention. Of particular concern is the ability of existing mines to execute and fund reclamation activities. Concern stems from a lack of demonstrated tailings reclamation technologies, perceptions of a poor track-record of reclamation activity by industry, and a lack of transparency with respect to the potential cost of reclamation activities relative to the monies secured in Alberta?s Environmental Protection Security Fund (EPSF). Limited information is publicly available regarding reclamation costs and technologies. Available data typically comes from disparate sources. This paper examines the expected costs of oil sands reclamation activities through a study of corporate Asset Retirement Obligation (ARO) liabilities, the Province of Alberta?sEPSF, and published data relating to reclamation costs.Issues relating to current liability funding are introduced.

Jan 1, 2011

By Patrick G. Hatcher

Studies of sedimentary humic acids by nuclear magnetic resonance (NMR), stable isotopes, and elemental analysis show they are derived by oxidative degradation of complex plant macromolecules that are insoluble in aqueous or organic solvents. The mechanism by which humic acids originate is fundamental to our understanding of the role of organic matter in ore deposition, because these substances can complex and mobilize a number of metal ions. The organic matter associated with uranium ores of the San Juan Basin, New Mexico and Carlin-type disseminated gold deposits of Nevada has certain organic geochemical characteristics that suggest an origin from humic acids.

Jan 1, 2013

By Y. Zhang, M. Yekich, C. Zhou, C. Jobes, J. Galanko, D. Tuchman, J. Srednicki, J. Carr

The continuous personal dust monitor (CPDM) is an essential instrument for working in hazardous environments, is used to monitor real-time coal dust exposure, and is mandated by the Mine Safety and Health Administration (MSHA) for underground coal mines. Researchers from the National Institute for Occupational Safety and Health (NIOSH) found that it is possible for electromagnetic interference (EMI) between a CPDM and a proximity detection system (PDS) to occur. Various approaches have been taken by researchers and manufacturers to address this EMI issue. Administrative controls were recommended to keep the CPDM six inches away from the wearable PDS device. Shielding pouches were made to contain the electromagnetic (EM) emission from the CPDM. Metal shielding was added to major EM emitting components. EMI filtering with large capacitors was introduced to mitigate EMI. Most recently, a novel magnetic-field-cancellation-based approach was developed and achieved remarkable results. In this paper, we provide a comparison between these approaches. The pros and cons of each approach are presented and discussed, so that mining device manufacturers and operators can best evaluate the technology and controls that improve the health and safety of mine workers.

Feb 1, 2023

By C. C. Jobes, J. J. Sammarco, D. L. Anderson

Computer-aided control of a mining machine places its operator in a safe, remote location, thus reducing health and safety risks. Sensing systems that provide machine position (xy coordinates) and heading (yaw) are extremely useful in aiding remote positioning of mining machines. The US Bureau of Mines (Bureau) developed two sensing systems for position and heading information: a scanning laser system based on the Lasernet sensor and a mechanical position and heading system based on linear-position transducers. The Bureau is also investigating a system from Honeywell, the modular azimuth and positioning system (MAPS), that employs ring-laser gyroscopes (RLGs). This paper presents a brief background and status of these sensing systems as applied to a continuous mining machine (CM). Included are field test results off each system operating in a room-and-pillar research section at a cooperating West Virginia mine.

Jan 1, 1993

By İbrahim Gunes, ATILA GURHAN CELIK, Eren Komurlu

This study introduces a new apparatus designed to improve the load-bearing capacities and insertion efficiency of split set type friction bolts. Laboratory and site studies demonstrated the apparatus’s advantages in terms of practicality and prevention of buckling. The apparatus temporarily compresses the split tubes, reducing friction during insertion and increasing normal stresses and friction capacity at the bolt-rock contacts.

Jan 3, 2022

By Prakash Venkatesan, Mehmet Ali Recai Ӧnal, Shaik Saida, Veerendra Singh, Chenna Rao Borra, Manish Kumar Kar

A laboratory-scale investigation of the effect of milling operation and catalyst addition ( K2CO3) on the partial reduction of low-grade pyrolusite ore pellets was carried out using coke as a reductant. Thermogravimetric analysis was used to understand the correlation between milling and catalyst addition parameters with the reduction temperatures. DTG analysis of pyrolusite pellet reduction showed three distinctive peaks associated with a three-step reduction mechanism (i.e., MnO2→ Mn2O3→Mn3O4→MnO). The results showed that the grinding and addition of the catalyst have a significant effect on lowering the MnO2 reduction temperature independently. But maximum reduction temperature drop is obtained when combining grinding and catalyst addition in this work. By 3 h milling and 10 wt% catalyst addition, the reduction temperatures were reduced by more than 200 °C compared to the raw ore pellets. These results obtained from the DTG analysis were further supported by XRD analysis of the reduced samples.

Dec 20, 2022

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By Nikhil Dhawan, Débora Moreira, Yogendra Pratap, Himanshu Tanvar

A glauconitic siltstone sample with a potash content of 10% is investigated as a potential potash source. The fine grain structure comprises potash bearing phases of glauconite, muscovite, and microcline. The as-received samples showed poor dissolution ~ 5%. Planetary ball milling was attempted for the dissociation of the underlying silicate structure for the potash release, and ~ 60% potash was obtained after 12-h milling. Mechanical activation (8 h, 60% NaOH) prior to heat treatment (600 °C, 30 min) was found successful in recovering more than 95%K values from glauconite. The final residue consists mainly of quartz, indicating a complete breakdown of the silicate matrix. The mechanical activation process followed is simple, adaptable, and less energyintensive compared to existing methods.

May 4, 2020

By R. Mensah-Biney

The kinetics of loading of gold from bromide solution onto an anion exchange resin, PAZ-4, were investigated in a batch stirred reactor. The initial loading rate was described mathematically by a first-order reaction rate equation. The effect of agitation speed, temperature, resin particle size, resin concentration, initial concentration of gold and bromine in solution on the rate was investigated. The model described fairly accurately the loading process in terms of the variables investigated. The rate constant for the initial loading ranged from 0.5 to 1.3 x10-3 sec-1 and the half-time was 9.3 to 56 minutes. The initial rate constant increased with increasing temperature with an activation energy of 15.7 kJ/mole (3.8 kcal/mole). The rate constant was directly proportional to the concentration of the resin in solution. The subsequent reduction reaction was also modeled by the first-order rate equation and the apparent rate constant was estimated to be 3.0 x 10-6 sec-1 with a half-time of about 44 hours.

Jan 1, 1994