Search Documents

By J. M. Van Langen

In 1965 Hoogovens was looking for additional capacity for burden preparation in the order of 2,5 to 3 million metric tons per annum of some kind of optimal blast furnace ore feed. In principle four solutions offered them-selves for further investigation: 1. purchase of screened ore and/or run of mine ores with the provision of a corresponding ore screening capacity on the blast furnace site; 2. manufacture of sinter; 3. purchase of pellets; 4. manufacture of pellets. After studying the technological, technical, economical and commercial factors Hoogovens decided for the last mentioned possibility. Before taking this decision not only a great number of different mixtures of iron ore were tested, but during a long period in one of the big blast furnaces a number of tests were also executed with purchased pellets from South and North America. It was found, that using 50% acid pellets with 40% basic sinter a coke rate saving of 25 kg per ton hot metal (50 lbs/net THM) and a production gain of 15% could be obtained as compared with a full sinter practice. With some pellets it became clear, that due to properties, commonly referred to as swelling, we got very poor furnace performances; so in studying the production of pellets, pellet quality should be regarded as the most important aspect of the problem.

Jan 1, 1972

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By Reed Thorne

To many people, rescue from elevated, sometimes vertical, locations brings about thoughts of heroism mixed with brawn and self-sacrifice. Images are conjured of cliff rescues where the technical effort is hanging from a few seemingly small nylon ropes hundreds of feet above the ground. Such is the vertical realm of technical rope rescue. This is a technical field in which the author serves professionally as battalion chief of (rope) operations for a northern Arizona fire district, and as a private sector instructor to mines in the United States and Canada.

Jan 1, 1996

By Xiaoting Li, Richard Adasiak, Benjamin Mirabile

Pumpable J-Crib stopping walls and Jennmar high-strength (HS) stopping panel walls are widely used for resisting high-ventilation air pressures and roof support in underground mines due to their installation efficiency, convergence allowance, and better performance than traditional concrete block stopping walls. Based on the different entry dimensions and required maximum ventilation air pressures of up to 36-in. water gauge, 24-, 27-, 30-, and 36-in.-diameter pumpable J-Crib stopping walls, or 18- to 30-in. thick Jennmar HS stopping panel walls can be designed, and their support capacities and convergence allowances are evaluated for better roof control. Pumpable J-Crib stopping walls consist of 0.187-in.-diameter steel wire reinforced, JCrib material-filled bags, and non-wire-reinforced filler bags in between. Jennmar HS stopping panel walls consist of two, 20-gauge (0.04-in.-thick), galvanized, cold-formed steel panels with J-Seal materials pumped in between. Based on the fundamental structural design principles and specifications of ACI 318-19(22), the compression and flexural strength, and shear resistance of the walls can be checked to be compliant with the codes and specifications following the load and resistance factor design (LRFD) method. Specifically, the 0.187- in.-diameter steel wires in the pumpable J-Crib walls and 20-gauge steel panels in the HS stopping walls are integral parts of the walls and are considered to effectively confine the J-Crib or J-Seal materials. These steel elements play a significant role in reinforcing and improving the strength or support capacity of the stopping walls from a structural design perspective. Because of the high ductility of low-density J-Crib/J-Seal materials and steel elements, these walls are good at accommodating or absorbing the roof convergence (≥5% entry height), which cannot be matched by a traditional concrete block stopping wall (Figure 1). Based on the successful design and application of these stopping walls in different mines for improving roof stability and avoiding the air leakage, the authors have formulated the design methodology and verified independently by the finite element analysis (FEA) simulation technique. This design methodology combines the fundamental structural design principles with specific wall dimensions and material properties, facilitating mine engineers and government agencies to understand the in-depth working mechanism of these stopping walls.

Jul 1, 2023

By Ray E. Harris

New developments have occurred in Wyoming's industrial minerals industry since the 32nd Forum on the Geology of Industrial Minerals in Laramie, Wyoming in 1996. The soda ash trona and bentonite industries have experienced overall growth. Gypsum and limestone production have remained constant, but have the potential for dramatic growth. The mining of zeolite ceased in 1997. The struggling dimension stone industry has increased production, but development has lagged behind the schedule predicted in 1996. The construction of a container glass plant and associated production of glass raw materials, as predicted in 1996 and imminent in 1998, is now on hold due to unforeseen market factors. Increases in railroad and highway construction have, and will, greatly increase the production of construction aggregate for local uses. An iron carbide industry, not foreseen in 1996, is in the planning stages.

Jan 1, 2001

By N. Bat, N. Sarantsatsral

Blasthole sampling practices were investigated at the Erdenet copper and molybdenum mine in Mongolia to address grade reconciliation issues. The goal of the study was to determine if the particle size distribution (PSD) of blasthole cuttings was accurately reflected in the samples. The study additionally examined if the measured grade was related to the particle size of samples. Using a sector sampler specifically designed to collect samples for the study, six large samples were collected from three blocks following a specialized protocol. Each sample was split into nine size fractions, ranging from larger than 12 mm to smaller than 63 µm. Copper and molybdenum grades were determined for each of the size fractions. For comparison, nine samples were collected from the same blocks following the standard mine sampling protocol. These samples were also split into the same nine size fractions. As with the other samples, grades were determined for each of the size fractions. The results showed that the PSD in the samples collected following the standard operating procedure varied significantly from sample to sample. This variation was much lower for the samples collected following the specialized protocol. Loss of fines was also indicated in the standard mine sampling process. These observations suggest that the standard sampling protocol did not consistently capture the PSD. The copper and molybdenum grades increased as particle size decreased, regardless of the sampling protocol used. This observation underscores the importance of the PSD of a sample being representative of the true PSD. Given the low number of samples in the study, it is not a strong conclusion that the standard sampling protocol captures the PSD inconsistently. However, it could be taken as a caution. On the other hand, the grade versus PSD relationship is more certain, given that it was observed regardless of the sampling method used.

Feb 1, 2017

By G. Wang

With the depletion of easy-to-treat phosphate resources, low quality phosphate ores with high carbonates, particularly dolomite impurities have to be mined to meet the agricultural demand because of the continued growth of world population. The separation of dolomite from phosphate has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physical and chemical properties. Flotation is considered the most important approach for beneficiating both easy-to-treat and high impurity phosphate resources. There is no doubt that the development of reagents is the key for achieving satisfactory separation performance through flotation process. In order to separate dolomite from phosphate, Arr-Maz Custom Chemicals has made great efforts in developing flotation reagents for removal of carbonates from phosphate ores of different origins worldwide. This paper describes some flotation reagents and processes for the separation of dolomite or/and calcite impurities from phosphate in the ores from different locations.

Jan 1, 2010

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

Despite several methods (empirical, statistical and machine-learning tools) to calculate blast-induced ground vibration, it is not easy to predict and simulate blast vibration precisely under varying blasting loads and strata conditions due to complications in the blasting procedure. In this study, field blast data were simulated in Ansys software using explicit dynamics, and ground vibrations for 20 single-hole blasts were monitored. The densities of emulsion explosives were in the range of 0.9 to 1.15 g/cm3. In the laboratory, rock properties were determined from rock samples collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and density of the emulsion explosive were also determined and used in numerical analysis to know the ground vibrations at specific points. The results of ground vibrations predicted by the model were validated using field data.

By S. G. Zahony

The Moris gold deposit resides in a massive ridge-forming sulfide-poor epithermal quartz and calcite vein system and consists of a mineable reserve of four million tons of 2.1gm Au/ton. Post-mineral normal faulting along the hanging wall of the main fissure has caused a hogback-like exposure of the vein, allowing for inexpensive opencut mining. The vein formed between pre-Cretaceous(?) phyllitic clastic sedimentary units in the footwall and Tertiary andesitic volcanic rocks in the hanging wall. Part of the ore reserve is hosted in a Tertiary conglomerate that rests unconformably atop the phyllitic footwall sequence. The original unoxidized vein material contained substantially less than 1 gram Au/ton. A four-fold upgrading of gold occurred by enrichment when gold recrystallization took place in the electric fields of oxidizing pyrite cubes.

Jan 1, 1993

By E. Watkins, S. J. Schatzel, V. Gangrade, R. Kimutis, J. Addis, C. Hollerich

The recent shale gas revolution in the United States has led to the drilling of hundreds of unconventional shale gas wells in active and future coal reserves in traditional coal-mining regions of Pennsylvania, West Virginia, and Ohio. This paper summarizes the impact of a shale gas well breach on the mine ventilation system of an operating longwall panel. This study utilizes a 1:30 scaled Longwall Instrumented Aerodynamic Model (LIAM) to simulate a single-panel longwall operation. The LIAM will be utilized to identify flow pathways and distribution patterns of gas from breached gas well scenarios in an operating longwall in the Pittsburgh Coal Seam. Sulfur hexafluoride (SF6) tracer gas is utilized to simulate a breached gas well. Preliminary findings suggest that the breached gas is diluted to regulatory levels and does not accumulate in the mine entries or in the longwall gob when the longwall panel is adequately ventilated. Overall, this study characterizes the potential interaction between shale gas wells and the mine environment in the event of a gas well breach, which provides critical information to the industry and regulatory agencies for improving safety, health, and welfare of miners.

Mar 2, 2022

By Dávila-Pulido. G., L. Magallanes-Hernández, F. López-Saucedo, J. Batista Rodríguez, A. Uribe-Salas

"This paper presents the results of tests performed to study the effect of slurry solids concentration on the behavior of gas dispersion in industrial-scale mechanical flotation cells. The experiments were conducted at five concentrator facilities run by a Mexican mining company, specifically in the rougher bank of the lead/zinc flotation circuits. Those mechanical cells having significant contribution to the performance of the circuit, that is, the cells that enable high recovery, were characterized. The measurement protocol enables measurement of the superficial gas velocity, gas holdup and bubble size, and sampling of the mineral slurry. The measured data indicate that bubble size and gas holdup decreases as the concentration of solids increases. IntroductionThe process of mineral concentration by flotation is based on contact between particles and air bubbles, the selective adhesion of hydrophobic particles onto the bubbles, and the rising of the bubble-particle aggregates to the surface of the flotation cell to overflow over the lip to form the concentrate. It is now accepted that the physical and chemical process variables that control the flotation of hydrophobic particles are closely related to gas dispersion (Schwarz and Alexander, 2005). Gas dispersion is defined by the superficial gas velocity, Jg (Torrealba-Vargas, Gomez and Finch, 2006), the gas holdup, eg (Tavera, Gomez and Finch, 1997), the bubble size, d32 (Dobby and Finch, 1986; Gorain et al., 1995; Hernandez-Aguilar et al., 2004) , and the bubble surface area flux, Sb (Manqiu and Finch, 1989; Manqiu, Finch and Uribe-Salas, 1991). In recent years, the advances that have been made in sensor technology have enabled the characterization of gas dispersion in industrial flotation cells with excellent results (Gomez and Finch, 2007). This technology advancement has allowed the gaining of a deeper understanding of such complex mechanisms as carrying capacity (Yianatos and Contreras, 2010), collection efficiency (Gorain, Franzidis and Manlapig, 1997; Massinaei et al., 2009) and bubble coalescence (Finch, Nesset and Acuña, 2008; Zangooi, Gomez and Finch, 2010)."

Jan 1, 2017

By V. T. McLemore

The Wind Mountain (WM) nepheline syenite deposit is part of the alkalic complex in the Cornudas Mountains, which ranges in age from 34.6 ± 1.5 Ma to 36.8 ± 0.6 Ma. The WM deposit consists of a complex, zoned pluton that ranges from syenite porphyry to nepheline syenite porphyry. The WM deposit has potential use for ceramics and dark-colored beverage containers and consists of nepheline, k-feldspar, albite, and varying amounts of other minerals. Analcime also is present locally but must be avoided because it is unsuitable for ceramic and glass. Chemically the deposit consists of 56-63 % SiO2 17-21 % Al2O3 and 4.0-5 % Fe2O3. Although initially iron is high, when the crushed rock is passed through a specialized magnetic separator, the iron content drops to below commercial maximum standards of less than 0.5% Fe2O3. The WM deposit is currently under exploration and testing to determine marketability.

Jan 1, 1994

By Amila Sandaruwan Ratnayake, T. Dilmi. U. Wijewardhana, H. C. S. Subasinghe

The value addition potential of ilmenite was examined using several characterization techniques. Raw ilmenite is composed of 93.65 wt.% of FeOTiO2, 3.55 wt.% of SiO2, 1.22 wt.% of Al2O3, and the remainder being other minor oxides. Ilmenite and powdered carbonized coconut shells were mixed in the weight ratio of 4:1. A separate fraction of the same mixture was added with powdered seashells in the weight ratio of 4:1:0.5. Six fractions of each mixture were distinctly milled from 1 to 6 h in a planetary ball mill. XRD spectra (broadened and diminished reflections of ilmenite) and FTIR observations (Ti―O―Cbonding) of milled samples indicate the possible incorporation of carbon into the ilmenite structure. Any clues of an occurrence of new rutile peaks were not observed in XRD spectra of milled samples. Consequently, the carbothermic reduction has not been initiated during mechanical activation. In this case, samples powdered for 6 h in a mill were isothermally annealed for 2 h under normal airflow at temperatures of 800 °C, 1000 °C, and 1200 °C, respectively. According to the X-ray diffractograms, the annealing temperatures of 1000 °C and 1200 °C exhibited almost similar trends with rutile (R), pseudobrookite (PB) and elemental iron (F), and a very few ilmenite (I) peaks. Consequently, 6 h of milling and 1000 °C annealing were concluded as the optimum conditions for the carbothermic reduction. Moreover, this study indicated seashells as a potential rate raiser for the carbothermic reduction of ilmenite at 800 °C. Therefore, this process is applicable to upgrade ilmenite into a mixture of synthetic rutile and elemental iron.

Mar 29, 2021

By T. Umadevi, A. Pratap Singh, R. Sah, K. Abhishek

"It was possible to beneficiate a low-grade iron ore fines sample from Bellary-Hospet, Karnataka, India assaying 56% Fe, 9.1% SiO2 and 5.2% Al2O3 and produce two concentrates, namely, a sinter-grade fines concentrate (43.7% by weight), assaying 63.6% Fe, 2.6% SiO2 and 1.7% Al2O3, and a pellet-grade concentrate (30.7% by weight) assaying 64.7% Fe, 2.9% SiO2 and 1.7%Al2O3. Rejects (25.6% by weight) assayed 32.5% Fe, 27.9% SiO2 and 15.4% Al2O3. The mineralogical characterization indicated that the sample consisted of 69.5% ironbearing minerals (56% hematite, 7.5% martite and 6% goethite-limonite), 12.5% quartz and 15.2% clay, and the rest were minor minerals. Liberation size was found to be in the size range of 25 to 100 µm. The process flow sheet consists of jigs, spirals, grinding and low- and high-intensity magnetic separation of the deslimed feed. IntroductionJSW Steel Ltd is a 10-Mt/a integrated steel plant. To produce 10 Mt/a hot metal requires nearly 16 to 20 Mt/a iron ore fines. The fast depletion of highgrade iron ore fines, increased industrial demand and an increase in iron ore prices have necessitated the exploitation and use of low-grade iron ore fines in the steel-making process after beneficiation. Thus, the beneficiation of low-grade iron ores by removing the associated gangue minerals and enhancing their grade is essential. The use of these iron ore fines in sinter and pellet making has prompted the undertaking of systematic studies on low-grade iron ores.Finely disseminated low-grade iron ores with siliceous impurities have been upgraded by gravity, magnetic and flotation-based processes (Burt, 1994; Svoboda, 1987; Houot, 1983). The processing of low-grade Indian hematite ore containing high levels of alumina-bearing minerals as impurities present separation challenges and pose special problems in martite and magnetite, in association with quartz and clay as the gangue-forming minerals. Alumina is mainly contributed by clay (kaolinite, montmorillonite, illite, alunite), lateritic material and gibbsite; some alumina occurs as solids in iron oxide minerals, namely, goethite and limonite. Silica is mainly contributed by quartz and the associated clay. achieving a high-grade concentrate (Pradip, 1994; Singh and Mehrotra, 2007). Hematite ore basically consists of varying amounts of hematite, goethite,"

Jan 1, 2015

By C. Iglesias

Innovation in the tilemaking ceramic industry is stressing properties like powder flowability, ability to toughen green tiles, so turning technological requirements of ball clays ever stricter in terms of plasticity, dispersion in water, rheological behavior, workability in the green state, refractoriness and firing colour. Technological performance of ball clays was improved by taking as benchmark the highest quality raw materials on the market. The mineralogy, plasticity, methylene blue index and ceramic response of the Patagonian ball clays are analogous to those of European clays, but improvement is needed to approach the highest quality materials. On this basis, the Frente A, Super, Puma, and Lote 8 deposits were selected and their characteristics enhanced by additions of highly plastic and white-firing corrective clays targeted on the benchmark. Porcelain stoneware formulations, containing improved ball clay mixes, were experimented at both laboratory and industrial scale. The improved ball clays behave like the best raw materials currently used, although modest changes occur in the mechanical properties, water absorption and whiteness of the fired products.

Jan 1, 2010

By A. Sullivan

Success in mining demands the creative application of equipment, systems and processes to the unique needs of each mineral deposit, market and, though often overlooked, the culture of the individual business. In recent years, domestic coal mining companies have become more attentive to the contribution safety and loss control programs have on their financial results. Although most have adopted fairly conventional safety programs, some have created systems and processes tailored to their unique circumstances. While each coal mining business must consider the typical risks inherent to our industry, excellence in safety is most likely achieved when a safety program is customized to meet the needs of the individual business.

Jan 1, 2000

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Southwestern New Mexico is part of a large belt of Late Cretaceous to Eocene copper porphyry deposits found in Arizona, New Mexico, and Mexico. These deposits are the result of arc magmatism that occurred during the Laramide orogeny. Recently, attention has been brought to other commodities that can be extracted as by- and co-products, many of which are critical minerals. A new compilation of the geochronology of these deposits shows two main pulses of magmatism that produced mineralized deposits and, along with new dates by the author, shines new light on the geologic history of these deposits and the role it plays in critical mineral abundance.

Feb 1, 2024