Search Documents

By Sandro Moro, Giuseppe Tiberti, Giovanni Plizzari, Antonio Conforti

"During TBM operations, thrust jacks apply high-concentrated forces to the last installed precast segment. These loads generate a disturbed region in the precast segment under the thrust jacks, in which significant tensile stresses (defined as splitting or bursting stresses) occur perpendicular to the load direction. In addition, due to the demand of compatibility, the combined effect of TBM high-concentrated loads determines tensile spalling stresses in the area far from the loads. Therefore, local rebars or fiber reinforcement are required in these areas. This paper focuses on the study of the effects generated by high-concentrated loads exerted by TBM hydraulic jacks, mainly in terms of both spalling and splitting phenomena. Experimental tests on small-scale specimens showed that polypropylene fiber reinforcement significantly enhances both the bearing capacity and the ductility. Moreover, polypropylene fibers resulted in very effective control of compatibility cracks.INTRODUCTIONTunnel segments are generally reinforced by conventional rebars (RC segments) in order to resist the tensile stresses both at Serviceability (SLS) and Ultimate Limit States (ULS).In the two last decades, Fiber Reinforced Concrete (FRC) has been used in many precast tunnel segments (sometimes also in combination with conventional rebars). Steel Fiber Reinforced Concrete (SFRC) is generally used for these applications even though there is a growing industry interest on macro-synthetic fibers for structural applications. Conforti et al. (2015) showed that polypropylene (PP) macro fibers can be used as shear reinforcement in both wide shallow and deep beams. Referring to precast tunnel linings, very few early experiences are reported in literature. Bonalumi et al. (2015) developed full-scale tests on tunnel elements reinforced by PP fiber reinforcement and conventional rebars (hybrid solution). The design process of segmental concrete tunnel linings generally models the standard load cases of demolding, storage, transportation, positioning and embedded ground condition. In all these stages the ring can be modelled as simple curved beam elements (having a height equal to the lining thickness and a width equal to the segment length). During these loading conditions, flexural demand is generally limited; thus, in case of conventional RC elements, a rather low ratio of longitudinal curved rebars is usually adopted (?s of about 0.2-0.3%)."

Jan 1, 2016

By W. G. Willson, Y. L. Li, P. D. Rao, D. E. Walsh

The combination of high moisture and low heating value has restricted most low-rank coal (LRC) usage worldwide to mine-mouth power generation. The objective of this study was to subject two Alaska low-rank coals to hydrothermal drying to enhance their marketability in the Pacific Rim markets and to evaluate the chemical and physical properties of the dried products as a function of process conditions. Coals from Usibelli Coal Mine and the Beluga coalfield have a heating value of approximately 18.5 MJ/kg and contain about 28% moisture. Hydrothermal treatment (at 275° to 325° C) of lump coal, from the Usibelli Coal Mine and the Beluga coalfield, enhanced the heating value of the material, on an equilibrium moisture basis, from 18.5 MJ/kg to nearly 27.8 MJ/kg. The product coal, with a high heating value and only 0.2% S, is an environmentally-acceptable premium fuel; additionally, with the Hardgrove grindability index of the coal greatly improved, its value is even further enhanced. An increase in hydrothermal drying temperature promotes vesiculation of resinite. Also, ulminite reflectance increased to 0.92%, and ulminite was subjected to widespread vesiculation; this resulted in a coke-like structure indicative that the material went through the fluid stage.

Jan 1, 1993

By Xiaochun Xiao, Xin Ding, Yishan Pan, DI WU, Xiangfeng Lv

Rockburst is a sudden disastrous instability of coal mass that poses a serious threat to underground exploitation of coal resources; therefore, approaches of prediction and control methods are valuable for improving mining environments. The mechanical properties and bursting liability of coal with drying, under-saturated, and saturated moisture content under uniaxial compression are investigated, and the charge induction signal during coal deformation both in the laboratory and on-site is recorded in this study. The presence of water reduces the cohesion and increases the internal stress caused by non-uniform deformation of minerals, resulting in the strength, elastic modulus, and bursting liability being weakened. The charge induction precursor main frequency band is 1–100 Hz and belongs to the very-low-frequency signal regime, and it indeed varies with the loading stage, leading to specimen failure owing to changes in amplitude and continuity of the charge pulse in both the time and frequency domains. Water inhibits the richness of charge induction and reduces the bursting liability, and the earlier the precursor appears, the more total charge emerges. Moreover, measurement results indicate that the amplitude and continuity of the charge pulse decrease over a longer time, as recorded in a coal seam with water injection, further verifying the weakening of the coal dynamic characteristics. Charge induction can be a valuable tool with which to obtain the precursors for rockburst and to aid the evaluation of water injection.

Dec 26, 2022

By J. F. Brune

This is a shortened version of the paper ?The Methane-Air Explosion Hazard Within Coal Mine Gobs published in the 2013 volume of SME Transactions (Brune, 2013). This paper analyzes the explosion hazard resulting from the formation of methane-air mixtures in the mined-out gobs of underground longwall coal mines. Evidence from numerous mine explosions suggests that explosive methane zones can form within longwall gobs. Explosions and fires resulting from these methane accumulations have led to severe and fatal injuries to the miners, including the explosion of the Upper Big Branch mine in West Virginia, where 29 miners lost their lives. The paper also reviews current research on numerical modeling of gas flows in longwall gobs and outlines how targeted injection of nitrogen into gobs can effectively reduce the volume of such explosive methane zones. The paper concludes that comprehensive monitoring of gas compositions along the accessible fringes of the gobs along with inertization, improved ventilation schemes and further research are necessary to control this explosion hazard and make mining operations safe.

Feb 23, 2014

By L. M. English

A basic model has been developed to help assess methane control needs for longwall mining of coal in gassy areas. Rather than depending upon reservoir and rock mechanic theory, it uses an empirically-determined gas emission rate as an input and operates on the assumption that, within a specific region and zone, gas emissions will be relatively equivalent for uniform incremental volumes of gob created by mining. The computer program divides longwall panels into segments, keeps track of the face advance, and generates emission rates and volumes for both the entire panel and for individual zones within the panel by summing values for all undermined segments. This model can aid the determination of the number, size, and location of vertical wells or other methane control applications that are needed for gob gas control.

Jan 1, 1998

By Immo H. Redeker

The Kings Mountain area of North Carolina is the lithium pegmatite center of the U.S., if not of the whole world. We have two spodumene and by-product mineral producing companies, Lithium Corp. of America, and Foote Mineral Company. We also have Kings Mountain Mica and Kings Mountain Silica Companies producing mica. feldspar, quartz and clay from weathered pegmatites in that area. Figure 1 gives the location of the spodumene pegmatite area in North Carolina. The two spodumene producers mine typical pegmatite ore in open pits after removing amphibolite or mica schist overburden which is sold to aggregate producers. The ore reserves are discussed elsewhere in this session. They are in the order of plus 50 million tons but not unlimited. 1.2 The major minerals found and concentrated from the North Carolina spodumene pegmatite ores are tabulated on Table 1.

Jan 1, 1977

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations related to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 370 to 1% S and greater than $28.65/t ($26 per st) for removal below 170 sulfur.

Jan 1, 1988

By N. C. Saxena, S. K. Puri, A. K. Pal

The condition-based monitoring system is an important innovation for reducing the downtime of costly, heavy earth- moving machinery (HEMM). Vibration severity measurements were made on the HEMM located at the Gevra Project, the largest coal opencast project in India. Whenever the vibration severity levels exceeded the permissible limits, necessary actions were taken to replace the defective parts of the ma- chine. The systematic vibration monitoring of 120-t (132-st) dumpers, followed by corrective measures led to a substantial increase in component life (8.18% for an 445E Dressor and 28.44% for an MK-30 Unit Rig). The associated costs (including spareparts) were reduced by 21.55% and 25.74%, respectively. Because of the reduced downtime, savings for these two dumpers over the period from March 26 to June 25,1998, were of the order of Rs.26.47 (US$0.649) million.

Jan 1, 2000

By R. Shields

"Hard rock mines move large volumes of material, which can cause the conveyors that are essential to this movement to suffer lots of problems, including carryback, spillage, dust and belt wander. Many of these issues are created at the transfer points where the belts are loaded.This article provides an overview of the latest transfer point systems that incorporate safety and serviceability by design as well as a report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, NV. Here, performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine.The importance of transfer pointsConveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance is the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created.The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material — cargo released in the form of carryback, spillage or airborne dust — that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems and issues with community relations. The U.S. Mine Safety and Health Administration estimates that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points.Technologies to improve transfer pointsA number of techniques to improve the performance of conveyor transfer points have been developed. They include:"

Jan 11, 2017

By T. Gupta, T. Ghosh

"Rare Earth Elements (REEs) and their compounds are essential for numerous modern high tech applications such as renewable energy technologies, catalysts and defense applications. The destabilization of REE pricing owing to the global demand and supply deficit has forced many countries to re-evaluate the possibility of indigenous production of REEs. Cost effective and eco-friendly opportunities are being widely explored for extraction of REEs from non-conventional mineral sources such as coal and coal byproducts to stabilize the supply chain. Coal from Central Alaska (Healy Coal Mine) and Southern Alaska-Cook Inlet (Wishbone Hill) province have been found to possess elevated REE concentrations as compared to average world coal estimates. The objective of the study is to enrich the REEs in the fine size fraction (-75 Microns) from Healy and Wishbone Hill by froth flotation technique. A Box-Behnken design was applied for modeling and optimization of some operating variables on the flotation to maximize REE enrichment. The variables studies were frother dosage, pulp density (% Solids) and collector dosage. Experiments were carried out using a statistical design and the main and interaction effects on response variable was evaluated by analyzing 3D response surfaces. Based on the experimental results the optimum flotation conditions for maximum REE enrichment in the froth fraction was obtained at 4.2% Solids and 32.7 ppm of frother dosage for Healy coal sample and 10% Solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic equation for modelling and optimizing the response variable is found to be independent of collector dosage for both the coal samples. INTRODUCTION Alaskan coal deposits are distributed in three major coal provinces and are in Cretaceous and Tertiary rocks. The climate, vegetation type and sedimentation process has attributed to low sulfur content (averaging 0.3 percent) in Alaskan coals compared to other coal deposits found across the globe. In Central Alaska-Nenana and Southern Alaska-Cook Inlet coal province coal resources are contained in Tertiary rocks while bulk of the Coal resource in North Slope coal province is contained in Cretaceous and Tertiary coal bearing rocks [1]. Coals from Central Alaska- Nenana (Healy) and Southern Alaska-Cook Inlet province (Wishbone Hill) have been found to possess elevated concentrations of critical REEs as compared to the amounts present in world coals (Figure 1). The Wishbone Hill deposit is considered a relatively small deposit, with about 14 million tons of identified reserves, compared to Healy which has over 500 million tons identified [2]. The REE concentrations up to 286 ppm and 524 ppm on ash basis have been reported by Gupta et al. in 2016 with elevated concentrations Ce, La, Y and Nd which are expressed to be of critical importance by US Department of Energy. Accordingly, the two coal samples possess the potential to be used as a REE resource in the near future under favorable socio-economic and geo-political scenarios. [3, 4]"

Jan 1, 2017

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

By Lynn B. Hales

Unfortunately, the term "control" has a negative connotation in the minds of many of our operating plant personnel. Whereas the opposite is true of those associated with research and technical centers in our industry. The magnitude of this difference in opinion and actual experience has often proved to be a major factor influencing the success or failure of process control applications. Through the years, many plant people have endured a number of unsuccessful attempts by "outside" people to "optimize" their plants; and these experiences have proved to have had quite a callousing effect on them. On the other hand, in many plants, successful process control efforts have made firm allies of the operating personnel, and have increased the number of metallurgical people who are well qualified and experienced in process control. The instrumentation industry, computer industry, and the mining industry's ability to quantify what is really happening in our processes have grown and developed rapidly since the first control efforts were made in the 1930's (1). Because of this-,: new control opportunities are becoming increasingly more feasible and older well established ones are becoming even more practical and necessary with regard to the economic s of our industry.

Jan 1, 1979

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011

By David B. Gladwin

Regional characteristics in the coal resource base have resulted in application of different mining methods across Canada. Longwall methods predominate in eastern Canada, whereas open pit, hydraulic and room-and-pillar methods are utilized in the west. Both provincial and federal agencies have regulatory responsibilities and both also share in the development of R&D programs. This paper outlines the scale and scope of the various agencies involved with health and safety R&D in our expanding coal mining industry. Specific R&D activities in ventilation, dust control, explosion hazards, tunnel boring, strata control and truck braking, which form part of the national program, are outlined.

Jan 1, 1982

By M. S. Enders

The McDonald deposit is a volcanic-hosted epithermal gold resource that is estimated to contain 251,000 kg of gold in 375 Mt of ore at an average grade of 0.7 g/t gold. Phelps Dodge exploration geologists, working for the Seven-Up Pete Joint Venture, discovered the deposit in 1989. By the end of 1992, 494 drill holes for over 113,000 m of drilling, bulk sampling, soil geochemistry, geophysics, metallurgical testing, engineering, and environmental studies had been completed to support feasibility studies. The discovery of McDonald required vision, persistence, and commitment of everyone from the geologist on the drill rig to the senior management of the company.

Jan 1, 1995

By Raymond T. Moore

The Federal Coal Mine Health and Safety Act of 1969 (FCMHSA) begins with this statement: "Congress declares that the first priority and concern of all in the coal mining industry must be the health and safety of its most precious resource -- the miner; . . ." At the Federal level this responsibility is shared by the Department of the Interior and the Department of HEW. The health research and standard setting activities under the Act are largely the responsibility of the Department of HEW, and with the exception of Title 4, Black Lung Benefits, have been delegated to our Institute, which I will refer to henceforth as NIOSH. In addition, we bear certain joint responsibilities with the Department of the Interior. These include dust sampling and respirator approval. To complete the picture, the Department of Labor has recently assumed Black Lung Benefit respon¬sibilities from the Social Security Administration under Title 4 of the Act.

Jan 1, 1974

By T. P. Meloy

In the last decade increased and prolonged interest has been displayed in the use: of tunneling or rapid excavation to solve many of the urban and industrial problems confronting our society. There has been talk and action on the interurban rapid transit systems for major cities, and even preliminary designs for a Boston to Washington interurban transit system. Much of this interest stems from the search to the solution of our increasingly complex urban problems, where the surface area must be given over more and more to the inhabitants, and the subsurface for transit, utility and other services. While tunneling is not a panacea to urban ills it holds a real solution to many existing problems. There is also, among the tunneling experts, a growing confidence that technical problems of rapid tunneling can be solved. To solve these problems, R & D money must be invested. If it is to be money invested either by private industry or governments, there must be significant returns on the investment to justify the research and development need to bring about the breakthrough that will make tunneling a major contribution to the solution of urban problems. To make these economic studies more extensive and more accurate tunneling demand figures were needed. To this end, the Organization of Economic Cooperation & Development - OCED - included in its Conference on Tunneling a section on tunneling demand. As a result of the conference the organization for Economic Cooperation and Development issued a report entitled "The Advisory Conference on Tunneling - Report on Tunneling Demand 1960-1980. " This report was presented at the OCED Conference on Rapid Excavation, held at Washington, D.C. To obtain the data in the Report, questionnaires were sent to the OCED countries and 18 replies were received from Australia, Austria, Belgium, Canada, Denmark, France, Germany, Ireland, Italy, Japan, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom, and the United States. While it is true, that data were missing, that sometimes the definitions were confused, and that several countries provided no cost estimates at all, in general, this report contains the most comprehensive gathering of data that ever existed in the field. All data in the OECD report is expressed in terms of meters or cubic meters, and costs are in U.S. dollars.

Jan 1, 1970

By A. Davaliev, K. Hrkovic, V. Pavlovic

On the territory of Macedonia in South Yugoslavia primary and dory gold occurences were known since ancient times. Remnants of numerous goafs and remainders of washaries on river terraces and alluviums date right back to the times of Phillip II and his son Alexander of Macedonia and from Roman times, as well as from the Middle Ages witness exploitation of primary and secondary gold. More recent explorations on primary and secondary gold occurrences date from the period between two World Wars. Over that period a number of private companies, each on their own jointly, carried out gold exploration, particularly of alluvial occurrences on rivers emptying into River Vardar, starting from Skopje to the Greek frontier. The latest gold explorations carried out In the alluvium of River Konjska date back in 1976, and in 1978 old terraces of River Konjska were explored. The Visibility Study was prepared on possibilities of exploitation of gold from River Konjska alluvium. In the paper are collected the basic date an all known primary and secondary occurrences of gold, the results of the latest explorations, and the study itself. To-date geological explorations and analyses show very interesting potentionality of River Konjska and River Vardar alluvium, which proves continuing of he further explorations. For the moment, it is necessary to re-explore more complete view of the deposit. After that it will be possible to make complete techno-economical estimation of the auriferious alluviums and the conditions of the evaluations of the alluvial gold. 1. REVIEW OF PRIMARY AND SECONDARY GOLD DEPOSITS IN MAOEDONIA,YUGOSLAVIA 1.1. Primary deposits Scarse data are available for primary gold deposits in Macedonia` being unadequate for clear

Jan 1, 1988