Search Documents

By Y. Wang, E. Forssberg, A. Johansson, B. Chan

A super-conducting high gradient magnetic separator with matrix vibration in dry separation mode is a powder purification device, which has been used to remove weakly magnetic impure particles from fine calcite powders below 53 µm in this study. A fundamental question concerned is the evolution of the matrix clogging under gas-solids loads. This paper presents the improvement of the separation selectivity using a method of mechanically based vibration on the matrix in the separator. The functions of the matrix vibration are discussed. The results indicated that the mechanically based vibration on the matrix within a high intensity magnetic field while a feed was introduced in an air stream, was found to be effective for the dry purification of fine powder materials.

Jan 1, 2001

By K. Park

Coupled influence of sulphidizers and xanthates on the electrokinetic property and flotation behavior of malachite was systematically examined via electrophoretic mobility measurements and microflotation tests. The electrophoretic mobility results for the malachite before and after surface modification with different types (Na2S and (NH4)2S) and amounts (1×10-7?1×10-4 moles/g) of sulphidizers, showed that the isoelectric points (IEP) of malachite differed at the low dosage level depending on the type of the sulphidizer, which ranged between 5 and 9.5. However, the IEP values were observed to be shifted from high to low pH values with increasing amount of sulphidizers and finally ranged between 3 and 4, indicating that the sulphidizers played a different role on changing the surface property of malachite. In order to further understand the effect of sulphidizers on the electrokinetic property and flotation behavior of malachite in a sulphidizer+xanthate system, flotation tests were carried out with malachite sulphidized with Na2S and (NH4)2S (adsorptive amount=8×10-5 moles/g) at different bulk xanthate concentrations. The results showed that the flotability of (NH4)2S-treated malachite was greater than Na2S-treated one over the entire xanthate concentration investigated, indicating that the type of sulphidizers played important role in malachite flotation; however, no obvious correlation between electrokinetic property and flotability of malachite was observed.

Feb 27, 2013

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011

By Guosheng Zhan

The Homestake Mine included the open cut and underground workings up to 2,484 m (8,150 ft) deep. The mine ceased mining activities in December 2001 after 125 years of operation. Pumping from the underground workings continued for 18 more months until June 10, 2003. Homestake had completed a comprehensive hydrologic evaluation on post-closure underground flooding prior to the shutdown of pumping. After closure, the mine was selected by the National Science Foundation as the site for the Deep Underground Science and Engineering Laboratory (DUSEL). An interim laboratory facility will be set at the 1478 m (4850 ft) Level. The final facility will be set at the 2256 m (7400 ft) Level or deeper. Pumping from the underground workings began on June 5, 2008 by the South Dakota Science and Technology Authority (SDSTA). During the period of June 2008 through March 2009, the pumping rate increased from 41 L/s (650 gpm) to 81 L/s (1,290 gpm) with an average rate of 60 L/s (950 gpm). As a result, the water level had been lowered more than 95 m (310 ft). It was found that the observed rebound and later decline to date is in close agreement with the model projections. Because of this, the authors of this paper reject claims of a lack of sufficient measurement devices in place and a lack of understanding of the hydrologic system at the Homestake Mine prior to shutdown of pumping in 2003 (Davis et al, 2009). Furthermore, it is believed that this validated model can serve as a useful tool for the SDSTA to manage future underground dewatering for the DUSEL operation. This paper evaluates the hydrologic conditions in the Homestake Mine area and projects the post-closure groundwater rebound and decline due to DUSEL pumping.

Jan 4, 2010

By T. Yegulalp, M. Castaldi

As global energy demands increase, there will be a critical need to employ fuels that have minimal environmental impacts. While hydrogen is considered the ultimate fuel for that purpose, hydrocarbon based fuels will be in use for a considerable time and will probably be the first major source of hydrogen for next generation power systems. The best fuel for this transition will be natural gas because of the high hydrogen to carbon ratio. Natural gas hydrates have the potential to meet the global energy needs for the foreseeable future. The amount of energy stored in natural gas hydrates is significantly more than that of all the other fossil fuels combined. However, most proposed techniques for recovering the natural gas from the hydrate require too much energy input, raise safety concerns or can only recover a fraction of the gas. This paper discusses the technical feasibility of a novel method of gas production in hydrate reservoirs. The method is an in-situ process that creates a point heat source in the hydrate formation. This method not only significantly reduces the energy input, but also has the potential to sequester as much or more CO2 than would be produced from combustion of the natural gas produced, thus making this in-situ methane production technique virtually carbon neutral. Simulations using FEMLAB™ show that the method offers an energy efficient and environmentally friendly way to produce natural gas from hydrate reservoirs. Preliminary results indicate that it is possible to have an energy efficiency of nearly 90% for land based reservoirs for hydrate loadings of 20%. The simulation results also suggest that alternatives to a point source can be employed which may improve the process efficiency.

Jan 1, 2007

By K. F. Bailey

Naturally occurring asbestos in aggregate and other mineral deposits, and the release of asbestos fibers into the ambient environment, is a public health concern. Determining the presence of asbestos in an ore body also presents a considerable sampling and analytical challenge. Improper and inaccurate identification of asbestos can result in unwarranted public and worker panic leading to significant costs to mine operators both in terms of dollars and company image. Some companies have been forced out of business simply because they had the non-asbestiform, prismatic variety of one of the six asbestos minerals. In the late 70’s, asbestos was found as a contaminate in a trap rock quarry in Rockville, Maryland. This discovery led to a massive overreaction by federal, state and local governments. In 1986, the Occupational Safety and Health Administration (OSHA) promulgated a final rule that regulated the common non-asbestiform mineral habits of actinolite, tremolite, and anthophyllite as if they were asbestos. The rule was reversed after a six-year struggle. Recently, the Libby, Montana, W. R. Grace vermiculite - asbestos, as well as the California chrysotile in serpentinite, and the New Jersey Southdown quarry – asbestos events have rekindled the entire issue of naturally occurring asbestos. It is time to get this concern addressed with sound science so that real asbestos is properly identified and controlled.

Jan 1, 2002

By Terry A. Rightnour

Multiple seam mining is predominant throughout the central Pennsylvania Appalachian coal fields. Wide ranges in individual seam thickness, coal quality, and overburden characteristics are common throughout the region. On typical mining permits, ranging from 404 x 103 to 2023 x 103 m2 (100 to 500 acres), often as many as eight seams are concurrently mined, with each interburden requiring unique economic and environmental consideration in the mine plan. Specifically, this paper presents several planning tools and operational guidelines developed in response to current regulations for the special handling of potentially acid-forming materials as they are related to development and operation of multiple seam mines.

Jan 1, 1984

By D. Caiden, C. S. Covil, P. J. Chamley

The paper describes the background to alternative delivery models, drawing on international experience, and introduces Project Alliancing/Contract Partnering, common risks and risk sharing on tunnel projects. A plea for early contractor involvement in design is made before describing some whole life design implications for tunnels. The paper concludes with four short case studies; Channel Tunnel Rail Link in the UK, Hull Waste Water Tunnel in the UK; Island West Sewage Transfer Station in Hong Kong, and the New Southern Railway in Australia.

Jan 1, 2005

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By Edwin K. Maughan

The Rocky Mountain region contains part of the paleocontinental shelf that lay in Arizona and New Mexico through Utah, Colorado, and Wyoming into Montana and North Dakota. The shelf was bounded by the northeast-southwest-trending Transcontinental arch and the Cordilleran miogeocline in late Paleozoic and early Mesozoic time. Major tectonic features that affected middle Phanerozoic sediments on the shelf were the Big Snowy trough and Williston basin in the north and the ancestral Rocky Mountains in the central part of the region. The Zuni uplift and similar positive areas occurred along the axis of the Transcontinental arch in the southern part. The late Paleozoic and early Mesozoic sedimentary rocks record transgressive-regressive marine cycles in which the Cordilleran shelf and much of the adjacent craton were inundated by epeiric seas. Early in the Carboniferous, an epeiric sea covered most of the shelf. Greater topographic relief developed in Late Mississippian, was at a maximum in Middle Pennsylvanian, and then diminished through Permian and Triassic time. The development in the Pennsylvanian Period of horsts and grabens along northwest- trending faults on the northwest flank of the Transcontinental arch resulted in the ancestral Rocky Mountain system. The eastern part of the region was emergent by Middle Triassic, and the emergence lasted until Middle Jurassic, owing to uplift along the Transcontinental arch. During the early part of the Mesozoic, the sediments were dominantly terrigenous and were deposited mostly in shallow littoral marine environments shifting to continental. Most middle Phanerozoic structural elements within the area of the shelf are characterized by lineaments that have either an east-northeast or a conjugate north-northwest trend. The east-northeast lineaments closely parallel the northeast trend of the continental slope (miogeocline) in Nevada to southern Idaho. The conjugate set closely parallels the northwesterly continuation of the miogeocline north of an approximately right- angle bend in south-central Idaho. The northeasterly trending Transcontinental arch and the northwest-trending margin of the Canadian Shield are parallel structural elements with the north- east and northwest trends of the miogeocline. The rectangular lineament pattern on the shelf suggests a system of rectilinear fractures within the underlying Precambrian crystalline basement rocks that moved several times in the Phanerozoic in response to external forces applied against the continental crust. Movement of these blocks influenced erosion, deposition, and lithofacies of the sediments in middle Phanerozoic time. Zones of crustal weakness, represented by the lineaments bounding these blocks, probably were influential in localizing sedimentary mineral accumulations and petroleum deposits, as well as later igneous intrusions, volcanism, and emplacement of hydrothermal ores. Igneous activity in this region was rare during the middle Phanerozoic, but these conjugate fractures seem to have been avenues for later passage of hydrothermal solutions responsible for ore emplacement.

Jan 1, 2013

By Roshan B. Bhappu

Integrating a research and development department into an engineering company's corporate structure can be rewarding to the engineering division, the R&D group, and, most of all, the company's clients. Actually, the R&D department is a logical extension of the conventional processing group within an engineering organization-but the R&D group provides services as needed to the engineering department while it is carrying out regular testing, pilot plant, and preliminary feasibility studies. Backup Services Provided With an R&D group, the engineering division does not need a process engineering group as such. The R&D group provides project backup services for feasibility studies, preliminary and detailed engineering, construction, and startup. The R&D group, in turn, benefits from its close association with project engineers, draftsmen, estimators, and computer capabilities in the engineering division. The client also benefits from the arrangement because R&D and engineering skills are available to both departments on an as-needed basis without standby eost. To handle the integrated responsibility of R&D projects, as well as conceptual design and preliminary feasibility studies, the R&D staff must be carefully selected. These research engineers should: • have a good background in plant practice as a mill superintendent or chief metallurgist; • be capable of organizing and supervising a testing program or a pilot plant campaign; •be innovative and willing to accept new ideas and concepts; • be able to translate lab test results into a workable flowsheet through sound conceptual design and feasibility studies; and •be able to communicate with clients. In short, the R&D engineer must be a jack of all process-engineering trades to successfully take a project from concept to operating reality. Engineers in a metallurgical R&D organization should have experience in mining and processing all types of

Jan 10, 1980

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By L. P. Johnson

Longwall mining has gained acceptance as a safe method of maintaining coal production where conventional systems were unsuccessful or uneconomic due to bad roof conditions (Kuti8). One of the major problems confronting American operators involves the correct choice of equipment which should be selected to suit the local mining and geologic conditions for optimum productivity. To achieve this, factors such as rock strengths, local geology, panel geometry, and panel orientation must be examined to optimize production and minimize down time due to ground control problems. Little quantitative information is available in the literature regarding the effects of geologic conditions on American longwall operations, and past implementations of longwall systems appear to have been based largely on experience. When mining engineers are able to assess the geologic conditions both quantitatively and qualitatively, they can more fully optimize equipment selection and panel design.

Jan 1, 1977

By Ira Sohn

This article revisits global projections made in 1981of eight metallic and fertilizer minerals for the year 2000. The objectives here are to quantify the differences between the projected and observed levels of consumption for the year 2000 for eight of the 26 nonfuel minerals covered in the earlier study. An attempt is then made to attribute these (often) large differences to the major determinants of minerals demand — income, technological, regulatory and other policy changes, and changes in the recycling rates of the metallic minerals. The eight minerals covered are aluminum, copper, iron, mercury, nickel, phosphate rock, potash and tin. This summary article presents the actual population, gross domestic product (GDP) and per capita GDP changes from 1970 to 2000, compared with the projected rates for these important determinants of mineral use, along with the observed growth rates of minerals consumption for the eight nonfuel minerals included in this study. When the projections are compared with the observed global consumption levels for the year 2000, the differences range from +43 percent for nickel to +229 percent for potash.

Jan 1, 2005

By Keith E. Meyers

Condition monitoring is a viable troubleshooting practice among many industries to extend equipment performance, minimize unplanned downtime, reduce maintenance and repair time and costs, and increase related aspects of plant safety. But obstacles abound for mining, mineral-processing and cement operations striving to implement the technologies. Harsh machine environments can muddy efforts. High vibration in machinery can interfere with wide-spread rollout. Staff expertise or skills may be lacking. And costs may be prohibitive. Fault detection has emerged as a practical and cost-effective solution to identify process and machinery faults before failure interrupts productivity or jeopardizes worker safety. Fault detection can be a stand-alone system or connected to plant automation.

Jan 1, 2005

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

?Classification System Efficiency (CSE)? is a simple, powerful concept which can be used to measure and improve ball mill circuit efficiency. This paper describes six plant case studies which demonstrate the use of CSE to diagnose and/or improve grinding circuit performance, with related improvements in circuit efficiency ranging from 3 to 30 percent. The increased effective mill grinding energy is recaptured from energy that was going into over grinding, which can greatly benefit downstream mineral separation. The achievable CSE for given circuit design/operating variables is described, providing every plant metallurgist with the means to determine the potential for increasing their particular grinding circuit?s efficiency through increased CSE.

Jan 1, 2012

By M. J. Miller, N. Ripepi, M. Karmis, J. M. Conrad

Unmineable coal seams present an opportunity to sequester carbon dioxide emissions from power plants, while enhancing the recovery of coalbed methane. Injected carbon dioxide is adsorbed and stored on the coal surface while releasing methane that can be commercially recovered. Carbon sequestration, therefore, allows the utilization of unexploited mineral resources while reducing “greenhouse” gas emissions. This paper presents the feasibility, efficiency and enhanced recovery potential of coalbed methane production using carbon dioxide sequestration in the Central Appalachian Basin. The focus of research is on geological characterization of unmineable coal seams in Central Appalachia and the corresponding carbon dioxide storage capacity. Virginia Tech and Marshall Miller & Associates, Inc. conducted this research under the Department of Energy’s Southeast Regional Carbon Sequestration Partnership program.

Jan 1, 2006

By P. R. Hervey

Quartz is the second most widely used electronic material, with approximately 3,000 tons of single crystals used each year. Virtually all of this material is synthetic; grown with a technique called hydrothermal growth. We will review the basics of hydrothermal growth, the feedstocks for these crystals, and the challenges to improving the growth process. We will also review the processing of these crystals, the markets and applications where they are used, and the global outlook for these markets.

Jan 1, 1999

By Leigh Freeman

This article provides an overview for a series of leadership development workshops offered through the SME Young Leaders Program. The first of these workshops, “Accelerated Development Plan,” will be held at the upcoming SME Annual Meeting in St. Louis, MO on Sunday, March 26. How does a foundation of technical competencies relate to the development of social competencies necessary for management and leadership roles in the resource sectors? Technical competencies provide the foundation for a successful career. Social competencies provide the framework on that foundation. Successful leaders will be those who develop competencies in all areas.

Jan 1, 2006