Search Documents

By H. T. Chiwaye

Risk analysis is an important step in the design of rock slopes in open pit mining. Risk is defined as the product of the probability of slope failure and the consequences of the failure, and is generally evaluated in terms of safety and economic risk. Most of the risk analysis done at present is based on the use of limit equilibrium (LE) techniques in evaluating the probability of failure (POF) of the slopes. The approach typically makes use of full Monte Carlo simulations of the limit equilibrium models, with all uncertain variables randomly varied. The number of required simulations is generally over a thousand, at times as high as 20 000, in order to produce statistically valid results of the POF. Such an approach is clearly not practical when using numerical modelling programs dueto the high computational effort required. This paper explores the impact of using numerical modelling instead of the traditional LE techniques in evaluating the probability of slope failure. The difference in the overall assessed risk, in terms of economic impact, for the mining operation is then evaluated. With numerical models, approximate methods are used in the calculation of the probability of failure instead of full Monte Carlo simulations. This paper will use a method called the response surface methodology (RSM) for estimating the POF from numerical analyses. Simple slope models were used to verify the accuracy of the RSM method by comparing the results with those obtained from full Monte Carlo simulations. It is shown that there is good agreement between the POF values computed using full Monte Carlo simulation and those obtained using the RSM method. Finally, the use of numerical modelling in the assessment of risk is shown to bring a significant difference in the result compared with that from LE methods. One of the reasons for the difference is that LE models tend to underestimate the failure volumes and hence the consequences of slope failure.

Jan 1, 2010

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

By K. Kasas, J Kermeci, S. Vujic, S. Secei, P. Kermeci

On the ‘Majdan III’ open pit mine, supplying with brick clays the production plants of the industry of building material ‘Potisje-Kanjiza’ from Kanjiza, a modern ECS (excavator-conveyor-spreader) complex was built, integrating four bucket excavators, six conveyors and one spreader into a whole. This complex connects the mineral-exploitation unit with the final brick-products plant of the company. Monitoring and management of the ECS complex is carried out by modern computer-supported information-management system (IMS) implementing most modern measuring-regulation, computer and GPS equipment. It was concluded that, for safety reasons, the functions of the IMS should be developed by a component of active visual monitoring of the ECS complex. For this purpose, the task of making a project on intelligent system for visual monitoring of the ECS complex was entrusted to the Department of Computer Application at the Faculty of Mining and Geology, University of Belgrade. This paper gives a review of basic project solutions. Keywords: Automation, process management, information management technology, visual system, intelligent systems, TV monitoring, surface exploitation, clay, Majdan III, Potisje-Kanjiza.

Jan 1, 2003

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

By Dave Capstick, Ken Garner, Jim Porter

Technologies and systems used in the management of energy consumption in the mining and metal processing industry are well understood and documented from the supply side of the business. It is our contention that in many instances, through a more complete understanding of the demand side of the business, based on the detail of the operations plan, will provide greater lead time in terms of the design, implementation and utilisation of power supply infrastructure. Thus, optimal management of demand in a proactive manner, based on production requirements, will ensure both security of supply as well as continuity of operations. This paper describes the technology and methodology that is being developed to enable the above statement to be achieved. We use a case study to demonstrate the ability of the tools and methodology and conclude by outlining the business benefits achievable as well as the future developments emanating from this initiative.

Jan 1, 2005

By S. N. Opperman

Testwork at Goedehoop Colliery showed that fine coal, essentially?150 microns can be successfully beneficiated using froth flotation. Both conventional and column flotation were tested. It was found that the traditional stirred tank type of flotation machines used in conventional flotation produced the best recovery of fine coal. After extensive testwork it was decided to develop a flotation machine on Goedehoop Colliery that would combine stirred tank and quiescent column technology. It was thought that this design would give the best combination of recovery and selectivity. The Multicell was developed and is producing results acceptable for Witbank coal flotation. Keywords: Multicell, Witbank coal flotation, froth, stirred tank, quiescent column.

Jan 1, 2002

By H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2008

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015

By H. Dong

This paper presents a heat conduction model to determine the erosion profile of freeze linings in a ferronickel submerged arc furnace. Kirchhoff transformation was adopted to simplify the nonlinear equation governing heat conduction. The boundary element method (BEM) and Nelder-Mead simplex optimization method were employed to solve an inverse heat conduction problem. Erosion profiles could be obtained when calculated temperatures at sensor locations agreed well with measured temperatures. The model was validated by comparing the heat loss through the linings, which was calculated by BEM and integral operation after erosion profiles were obtained, with the value calculated from industrial data such as actual power consumption, tap-to-tap time, and ferronickel output. The optimal solution for the erosion profile could be acquired when the difference in heat losses calculated by these two methods is at a minimum.

Jan 1, 2014

By A. D. Engelbrecht

An investigation was undertaken to ascertain the suitability of four selected low grade, South African coals for gasification in a bubbling fluidized bed for production of synthesis gas and for the development of integrated gasification combined cycles (IGCC). This study consisted of the characterization of the coals, laboratory evaluation of intrinsic reactivity, and experimentation with a pilot-plant fluidized bed gasifier. Results of the characterization experiments show that the selected coals are high in ash, rich in inertinites, very dense (low porosity), with low caking indices and high ash fusion temperatures. Reactivity measurements with a thermogravimetric analyser (TGA), under reaction rate controlling conditions with carbon dioxide, showed that the reactivity of the coal chars decreases with increase in rank of the coal, as expressed by the vitrinite random reflectance and carbon content of the parent coals. The fixed carbon conversion achieved in the fluidized bed gasifier also correlates well with the rank parameter of the coal, with higher conversions being obtained with the lower rank coals. Thermal shattering and attrition of the coal particles produce significant amounts of fines, which correlate with the grindability indices, and no agglomeration (non-caking) was observed. It is concluded that fluidized bed gasifiers are able to utilize typical low grade, high ash South African coals for synthesis gas production and for inclusion in integrated gasification combined cycles for power generation.

Jan 1, 2010

By E. Hakami

The objective of the study was to estimate the largest shear displacement that could be expected on a pre-existing fracture located in the repository area, due to the heat release from deposited waste. Two-dimensional numerical analyses using UDEC have been performed. The maximum shear displacement, at the fracture centre, amounts to 0.2 – 13.8 cm depending on fracture parameters. The fracture extension, friction angle and shear stiffness are found to be the most important. Le but de cette étude est de déterminer le déplacement maximal en cisaillement qui puisse se développer le long d'une fracture préexistante en réaction à la chaleur dégagée par les déchets radioactifs enfouis dans la roche. Les analyses numériques ont été réalisées à l'aide du code 2D UDEC. Le déplacement maximal en cisaillement enregistré au centre de la fracture varie entre 0.2 et 13.8 cm en fonction des propriétés de la fracture. L'ouverture, l'angle de friction et la rigidité au cisaillement semblent avoir une influence dominante sur les résultats. Zielsetzung der Studie war die Abschätzung der maximalen Scherverschiebung, die auf einer innerhalb des Endlagergebietes existierenden Rissfläche infolge der Wärmeabstrahlung des eingelagerten Materials zu erwarten war. Es wurden zwei-dimensionale numerische Berechnungen mit UDEC durchgeführt. Die maximale Scherverschiebung im Zentrum der Rissfläche beträgt 0.2-13.8 cm, abhängig von den Risseigenschaften. Dabei hat sich herausgestellt, dass Rissgrösse,Reibungswinkel und Schersteifigkeit den grössten Einfluss haben.

Jan 1, 2003

By M. Gaula

"Gold bearing deposits of the Witwatersrand basin are generally less than 2m thick and require conventional narrow-reef mining methods for extraction and employ explosives as a means of rock breaking. Optimal utilization of explosives is dependent on the overall design of the blast. The under-utilization of explosives arises when shot-holes are drilled inconsistently, overcharged, and when tamping is absent. This can be rectified by emphasizing the importance of good drilling practices as part of induction programmes and refresher courses. The project was aimed at determining whether or not explosives are being optimally utilized at project site. This was investigated through a study of the properties of explosives, mine standards, and recommendations for usage. Underground observations were made to determine whether or not mine standards were being adhered to. Historic data was obtained to establish the historic relationship existing between the quantity of explosives used (kg) and the production output (m2). This was then compared to the quantity of explosives the mine expects to use per unit of production. The results obtained were analysed to determine the presence and extent of over- or under-utilization. It was found that explosives are being under-utilized at the mine. More explosives are ordered than expected per unit of production. The explosives’ properties are not thoroughly exploited during blasting, thereby requiring the use of more explosives than prescribed. Paper written on project work carried out in partial fulfilment of BSc. (Mining Engineering)"

Jan 1, 2015

By Z. Leng

"After detonation of the explosive, the final blast-induced damage area around the blast-hole falls into three categories, namely crushed zone, fractured zone, and elastic deformation zone. This paper presents a modified model to calculate the size of crushed zone around a blast-hole in drill-and-blast, with the hoop compressive stress and cavity expansion effect taken into account. The material in the crushed zone was assumed to be a granular medium without cohesion, but with internal friction. On this basis, the formula for crushing zone radius was derived. The proposed approach was verified with tests reported in the literature and the simulated results from SPH-FEM coupled models. A full statistical analysis was also carried out, and the predicted values were found to be in better agreement with the test results compared with other models. A sensitivity analysis of the modified model showed that the size of the blast-induced damage area is mainly affected by the following factors: rock mass properties, in situ stress, and borehole pressure. In particular, the roles of borehole pressure and in situ stress are discussed. Finally, suggestions are made on how the size of the crushing zones can be decreased. IntroductionOver the past decades, drill-and-blast has become the most commonly used technology in rock excavation. It is well known that in rock mass fragmentation with explosives, the annular rocks around the blast-hole are converted into fines. The formation of these fines consumes a significant part of the energy of the detonation, which in general is ignored in the determination of the efficiency of detonation (Glatolenkov and Ivanov, 1992; Furtney et al., 2012). Many studies show that only 20–30% of the total explosive energy is effectively used in fragmenting the rock, and up to 50% of the energy generated by conventional charges is wasted in overcrushing of the crushed zone and the inner part of the fractured zone (Ouchterlony et al., 2004; Sanchidrian et al., 2007). How to control the crushed zone to enhance the effective utilization of explosive energy, reducing the unit explosive consumption and the engineering cost, is therefore of great significance."

Jan 1, 2016

By K. N. Karparov

The classical limit equilibrium methods are suspected to be ineffective in predicting the potential for highwall failure in many instances in coal mines around the world. Slope engineers have for many years recognized a block thrust failure mechanism for slope failures, but little work had been done before 2000 to explain the actual mechanisms which must be responsible for the failure. The main reason for this is that limit equilibrium methods implicitly assume rigid blocks, and the resulting force equations must be satisfied everywhere simultaneously for them to have any meaning. This paper will show that the material involved in the slope failure is not rigid; indeed it undergoes considerable permanent deformation during failure. This observation allows the authors to treat the block boundaries independently, because they need not maintain a constant spatial relationship with one another, as is assumed in other methods. To enable analysis of this type the authors assume that the weight of the blocks is evenly distributed. This is reasonable, because the slope material is not strong enough to be self-supporting without some sort of constraint, or strong enough to be able to apply point loads to the surrounding material. The purpose of this paper is to extend the practical application of the analytical method developed from mechanism studies to provide an objective assessment of the risk of slope failure, and therefore guidelines for more stable slope designs. This work is based on studies carried out on two failures in an open pit coal mine in South Africa, and provides a methodology to assess the potential for failure more objectively than is possible with currently accepted methods, while at the same time remaining sufficiently simple to allow a ?back of the cigarette box? assessment by geotechnical engineers on site.

Jan 1, 2009

By H. Jalkanen, L. Holappa

The main role of slag in oxygen converter processes is to absorb the non-volatile oxidation products of hot metal impurities, Si, P, Mn, Ti, V, etc. The importance of converter slag as deP and de Smedia has ceased with implementation of special pre- and post-converter treatments. The transfer from top blowing (LD) to combined blowing converters has decreased the amount of slagged iron that, together with the tendency towards lower silicon and manganese contents, has decreased slag to steel ratio. Still the control of slag forming and behaviour during the blow is of great importance. In this paper the thermodynamics of the slag forming reactions, the role of slag in the modern oxygen converter process for impurity elimination, splashing, lining wear, dust formation and post combustion are discussed on the basis of common knowledge and experience of Finnish steel plants.

Jan 1, 2004

By P. W. J. van Rensburg

Our mineral heritage - PRESIDENTIAL ADDRESS given by P. W. J. van Rensburg, Pr. Eng.. B.Sc. (Eng.)(Rand) INTRODUCTION Stone Age people were living in various parts of South Africa as recent,ly as a thousand years ago, when they were displaced by Iron Age people with a culture developed in the far north. These invaders brought farming, building, and the earliest mining developments to the Transvaal, thus ushering in the beginning of our great mineral heritage. It is of particular interest to record that, up to comparatively recent times, some of these people were excavating iron-bearing shale rocks for their smelting furnaces on the Melville Koppies in J ohannesburg. Although the most recent the iron-smelting furnaces discovered on these koppies is estimated to be some five-hundred years old, it believed that these Iron Age people were driven out, and their settlements destroyed, by Zulu impis only one-hundred-and-fifty years ago.

Jan 10, 1973

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

By A. Nel

The gold mining industry in South Africa stands to benefit much from the implementation of the self-directed work team concept. Its introduction implies flatter hierarchical structures, empowerment of the workforce and increased participation. Research indicates that half of the initiatives to implement self-directed work teams, however, fail, and it is therefore imperative for companies to be aware of the factors impacting on the effectiveness of self-directed work teams in order to focus on these early in the implementation phase. The objective of the study was to qualitatively determine these factors. Semi-structured interviews based on the phenomenological method were carried out. The sample included members of, and individuals involved with, self-directed work teams (N= 26) from a large gold mining company in South Africa. Results show that most respondents rated the availability of resources to do their work as the most important factor affecting their effectiveness.

Jan 1, 2006