Search Documents

By N. V. Nemchinova, A. A. Kozlov, A. V. Epiforov

The gold dissolution in sulfuric acid media during industrial oxidative leaching test of sulfide gold-copper flotation concentrates has been achieved. The reason for this was using technological water containing thiocyanates and cyanides, which can dissolve gold under these conditions. The carbon in column (CIC) process for gold recovery from these solutions was proposed. However, significant amounts of copper and iron were adsorbed onto the carbon during CIC technology industrial tests. This resulted in a decrease of the gold content in the loaded carbon up to 0.5 kg/t. Further development of the technology was conducted by optimisation of gold and impurities stripping and implementation of carbon reactivation. It was shown, that the copper extraction from the loaded carbon during cyanide treatment was about 95%. The copper content in the stripped carbon after cyanide treatment was 1.76 kg/t. The gold recovery during high-pressure elution by caustic solution was 98%. The hydrochloric acidic treatment with thermal pre-treatment (reactivation) for removing iron and calcium from gold-free carbon was proposed. In this case, the iron and calcium extractions from carbon were 40-45 and 50-55% respectively. These tests showed that for carbon recycling the sequence operations of ‘cyanide treatment, gold elution, thermal pre-treatment, hydrochloric acidic treatment’ can be used. Keywords: Thiocyanate leaching, recovery of gold, carbon adsorption, gold elution, copper stripping, thermal reactivation of carbon, activated carbon, carbon-in-column

Jan 1, 2020

By J. Petersen, T. Moyo, D. Maharaj

This study investigates the effect of ammonium thiosulfate on the leaching of gold from the contacts of unpopulated cut electronic printed circuit boards (PCBs). Studies in the literature show ammonium thiosulfate to be a viable option in comparison to the commonly used but hazardous cyanide leaching route. However, the simultaneous dissolution of Cu interferes with the Au leaching reaction, often limiting the extraction to moderate levels. To optimize the system, an ammoniumthiosulfate system containing 0.5M ammonia, 0.5M ammonium thiosulfate, and Cu(II) sulfate at varying concentrations was studied as an alternative hydrometallurgical option for the recovery of gold from PCB. Tests were done with unpopulated standardized model PCBs (cut to 15 x 30mm pieces). Gold extraction of 47.3% was achieved after a 24-hour leaching experiment with a 0.02M copper background concentration. Further experiments focused using different initial background Cu concentrations (0M – 0.1M) to determine its effect on both gold and copper extractions. An initial Cu concentration of 0.045M resulted in the highest gold extraction, with 93.7% extraction after 6 hours of leaching. Further analysis of the data shows that the kinetic rate of gold leaching is correlated in a first-order dependence with the actual copper concentration in the solution, which increases with the concomitant dissolution of copper and gold from the PCBs. A lower threshold of 0.017M and an upper threshold of 0.15M copper in solution were determined, in between which gold extraction shows this first-order rate increase. The upper threshold is potentially linked to the onset of copper precipitation, which blinds the metal surfaces, slowing further leaching. The findings of this study suggest that in an industrial recovery operation of gold from waste PCB using the thiosulfate method, copper concentrations need to be carefully monitored, and the process should preferably operate with uncut or coarsely cut untreated boards to minimize exposure to copper circuits.

Dec 11, 2024

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By R. B. Khumalo, M. S. Nyarela, R. C. Nemathithi

Palabora Mining Company is one of the largest low-grade copper mines globally. The mine uses block caving for the extraction of the orebody. This paper enumerates the drawpoint loading strategies for the overall head grade improvements, particularly for a block that is nearing depletion. A comprehensive literature review of various considerations relating to improving productivity in block caving is presented to contextualize the draw control in caving. From this study, an optimized draw control strategy is presented, which focuses on three parameters that include grade distribution, loading compliance, and tonnage splits per sector. An empirical method based on the relational study between various parameters is used to outline the key criteria to be used in the optimization of drawpoint loading in block caving.

Nov 30, 2022

By S. Plaatjie, L. Linzer, M. S. D. Manzi, M. Sihoyiya

Fiber-Optic Sensing and UAV-Platform Techniques for Innovative Mineral Exploration (FUTURE) is a joint European Union and South African consortium project funded under ERA-NET Cofund ERA-MIN3. The project aims to develop cost-effective and novel seismic methods to image geological structures ahead of the mine face, ultimately leading to improved decision-making and safer mining practices. In this study we present results from numerical simulations conducted at South Deep Gold Mine for active in-mine seismic surveys. The study uses a finite differencing code known as WAVE3D, which models models the propagation of a seismic wave generated by stress pertubations that are applied to a defined grid. The numerical simulation model included two major ore bodies (Black Reef and Ventersdorp Contact Reef) and mine tunnels. The model was constrained using laboratory physical property measurements from underground borehole samples such as seismic velocities (e.g., compressional and shear waves) and bulk densities. Two case studies were created, one modelled the active shots and receivers on surface, and the other modelled the shots at depth (in a mine tunnel at ~4000 m depth) with receivers on surface. In both cases, the objective was to investigate the wavefield propagation through the rockmass between the mine tunnel and surface. The simulated wavefield produced by the source located along the mine tunnel was successfully recorded on surface. The surface-recorded wavefield exhibits clear one-way P-wave arrival times at approximately 450 ms to 500 ms, which can be used to calculate the surface-tunnel P-wave refraction tomogram. The results from the study were used to constrain the design, and for the acquisition and processing of the real surface and in-mine seismic surveys acquired under the FUTURE project.

Jan 12, 2025

By O. Dahl, B. Musuku, N. Schreithofer

Recovery of fine pentlandite is proving to be a challenging task in the Kevitsa sequential flotation operations, with over 60% of the nickel losses reporting into the -25μm size fraction. Since commissioning, the Kevitsa process has undergone major changes to address throughput and flotation performance. Major changes were implemented in the configuration of the milling and flotation circuits as well as in the operating conditions and reagent regime. Some of these changes improved nickel flotation while others deteriorated flotation performance. Most of the changes have had a direct impact on nickel flotation. This paper reviews the systematic analysis, laboratory testing and salient changes done to the process with special focus on the impact on the fine pentlandite flotation. Keywords: Blending, Flotation, Chalcopyrite, Pentlandite, Fines

Jan 1, 2020

By F. Yang, T. Pan, T. Zhao, Z. Shao, D. Zuo

In this paper, the development and applications of robot technique is summarized, and the status and developing direction of China coal mine robotics. A description of the research meaning, frame and key technology of underground salvage robot is given. Keywords: coal mine, robot, special robot, salvage robot.

Jan 1, 2003

By J. Zhang, A. J. S. Spearing, L. Ma

Ore deposits are becoming more complex to mine as a result of the exhaustion of surface and other easily mined deposits. There is also increasing socio-political pressure to design more environmentally sound, sustainable, and safe mining practices. Wang and Ma designed a mining method for coal, similar to a modified drift and fill using a continuous miner to take sequential cuts (rooms) that are subsequently backfilled. The authors have modified the concept to make it more autonomous, safer, and less costly using highwall coal mining techniques, modified and adapted for underground applications. The method is more flexible than longwall mining and the percentage extraction would seem to be in the same range. In addition because of the backfilling, surface subsidence would not be a major issue and could be more effectively managed.

Feb 2, 2021

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By I. Wayland

Value added blasting is a process methodology that links tasks and processes, with the aim to improve/enhance the technical application of explosives technology and initiating systems, resulting in improved output. The phases and steps of a typical value added blasting intervention are discussed in this paper. Each step having distinct purposes, principles and methodology. The underlying philosophies and process steps of the programme are described for each step. This paper gives an account of projects that have been completed in two Anglo American Gold Mines. This will include a description of the projects that were conducted at Vaal Reefs 8 Shaft and Western Deep Levels South Mine covering: ? The need for blasting improvements ? The approach that was followed ? The result of the programme.

Jan 1, 1999

By B. M. Van Vliet

SYNOPSIS This paper outlines the principles involved in the regeneration of activated carbon for renewed use in the recovery of precious metals or the purification of water. While chemical methods are effective in restoring the activity of spent activated carbon containing only single or defined adsorbates, thermal methods have to be used when the spent carbon is loaded with a heterogeneous mixture of adsorbates such as those normally present in industrial process streams or effluents. The steps involved in thermal regeneration are described, together with the operating conditions that can be controlled to give the required degree of activation. Finally, an account is given of the structural changes that occur in a new or spent activated carbon during thermal treatment.

Jan 1, 1991

By A. W. Bryson, J. D. le Roux, B. D. Young

Several rate models for the adsorption of gold cyanide from aqueous solution onto activated carbon are given in the literature. The purpose of this study is to critically examine their ability to simulate the adsorption process over a wide range of conditions. An account is given of a comprehensive set of experimental work on the kinetics of gold adsorption onto a coconut shell- based activated carbon. Equilibrium isotherms were also determined. It is concluded that the homogeneous surface-diffusion model fits the experimental data reasonably well and provides a good balance between simplicity and descriptive accuracy. The model contains two parameters: the extra-particle mass-transfer coefficient and an effective intraparticle surface-diffusion coefficient. Both can be evaluated readily from simple adsorption experiments.

Jan 1, 1991

By V. H. R. Brereton

The gold deposits of the farms Lisbon and Berlyn in the Eastern Transvaal by V. C. H. R. BRERETON* (Visitor) This paper describes the discovery and recovery of gold, over a period dating back to the 1870s. on the farms Lisbon and Berlyn, situated approxim ately 1I km north-east of Pilgrims Rest. where mining ceased in July 1971. 99 years after gold was first discovered in the Pilgrims Rest and Sabie districts. Included in the paper are accounts of the discovery and mining operations of the Lisbon-Berlyn Company from 1884 to 1890. The operations of small companies and syndicates. the superficial winning of gold by diggers, and the encouraging reports of four mining engineers in 1890 are also mentioned.

Jan 11, 1973

By J. P. G. Pretorius

The size effect in tests of the compressive strength of coal specimens differs from predictions based on the Weakest Link theory. Predictions of the size effect in tensile tests on lengths of cotton yarn and glass fibre, the behaviour of which is analogous to the weak link process, also differ from observations. This discrepancy is shown to be caused by the correlation between the strengths of the unit lengths in a composite specimen. The Weakest Link theory is reformulated as the Weakness Correlation theory to account for such correlation. It is shown that weakness correlation is found in rock and it is concluded that at least part of the discrepancy between the predicted and observed size effect in rock strength tests could be attributed to this correlation.

By H. C. Voges

An account is given of the tests being conducted by Iscor on the following processes for the beneficiation of coal fines: froth flotation, gravity separation, heavy-medium separation, and pneumatic and column flotation. The coals used in the tests came from the Durnacol, Tshikondeni, Grootegeluk, and Hlobane collieries. The problems involved in the dewatering of fine products are stressed. From a theoretical study of the efficiencies that should be possible for a hypothetical South African coal, it is concluded that future fines-beneficiation plants in South Africa may use standard heavy-medium cyclones for coal down to 1 mm in size, fines heavy-medium separation for the 1 mm to 450 µm fraction, and column or pneumatic flotation for the minus 450 µm fines.

Jan 1, 1991

By K. R. Vost

"In situ" measurements of the surface heat transfer coefficient in underground airways by K. R. VeST,* B.Se. (Glas.), M.Se. (N.S.W.) (Visitor) Few "in situ" measurements have been made of the surface heat transfer coefficient in mine airways despite the importance of this coefficient in determining the heat flow into the ventilating air. In this paper, the values obtained at various air velocities and the comparisons of these values with theoretical values are given. Examples are also given ofthe errors which would result if rock surface temperatures were obtained by extrapolation from temperatures further into the rock without taking into account the time delay which occurs before a given change in air temperature reaches the points from which extrapolation is carried out.

By M. B. Cortie

An account is given of the development of ferritic stainless steels since their discovery in the early years of this century. The alloys became very widely used in the 1950s, the market during that decade being driven strongly by a demand for automobile trim made of ferritic stainless steel. The production of ferritic stainless steel declined as a proportion of the total at the end of the 1950s as consumer preferences changed. However, the market is now growing strongly again, this time driven by a demand for oxidation-resistant alloys for motor-vehicle exhaust systems. The tonnages produced, applications, and market shares of the various alloys are discussed and compared. Trends in world stainless-steel production, product forms, technological development, and usage are examined.

Jan 1, 1993

By I. D. Wood

Deposition of gold-bearing deposits in the Witwatersrand Basin was controlled by hydraulic processes. These resulted in the formation of independent sedimentological facies areas having different statistics and semivariograms. Consequently, when there are indications that data are a mixture of statistical populations, it is important to decompose them into statistical subpopulations and analyse these independently. However, in the case of actual mining, physical position and extent of sub- populations are important and, as a consequence, any decomposition of data must take space into account if it is to be of use. An algorithm for the spatial decomposition of data into its sub-populations is described and is applied to real data taken from the Witwatersrand. Two distinct areas with completely different geostatistical parameters were revealed.

Jan 1, 1987

By F. Wang, P. Rosario, A. Vazirizadeh

Advances in data science, machine learning, and artificial intelligence are transforming mining and mineral processing, and making them more algorithm intensive. The paradigm is shifting from one of detection and control to one of prediction and optimisation. To build up reliable prediction and optimisation models these steps should be passed: collect, aggregate, cleanse, and process large amounts of complex, structured, and unstructured data as a first stage. Next, the right tools must be used to extract meaningful features from the operational data for the build-up of a prediction model. A grinding circuit is one of the challenging areas in terms of determining its overall efficiency and the prediction of product quality. In a processing plant, some of the KPIs are typically unmeasurable or infrequently measured for real-time application, e.g. ore grindability and grind size. However, these variables are required to calculate the grinding circuit efficiency and to model the operation performance. In this paper, advanced analytic tools have been used to extract one selected KPI (cyclone overall P80 or final grind size) and its relationship with measured variables for an industrial dataset. The results illustrate that the performance of the grinding circuit can be predicted for real-time monitoring by means of measured data. Keywords: Grinding circuit, data-driven, machine learning, process modelling, hybrid modelling

Jan 1, 2020

By A. Brodt, I. Mezhibovsky

The traditional vertical transportation systems deliver both gangue and useful mineral. The extraction of the desired minerals requires the construction of mineral processing and waste management plants, driving production costs, and often creating a negative environmental impact. The proposed technology is an integration of mineral processing within the transportation system. The mined rock is crushed and then loaded into a vertical lifting system filled with heavy media, with an intermediate density between the mineral and the waste rock. Driven by gravity separation, the desired mineral floats to the earth's surface, while the waste sinks. Delivered minerals and sunk waste is extracted from the heavy media and is then regenerated to a dry state. The useful mineral should be suitable for further use, and the waste used for backfilling. Remained residues of the heavy media may be recycled and reused in the vertical transportation system. Trials of the proposed process in a pilot format have confirmed economic and environmental advantages over traditional methods of transportation and mineral processing technologies. Keywords: Gravitational processes of mineral processing, separation in heavy media, vertical transportation to earth's surface by floating up

Jan 1, 2020