Search Documents

By P. Vlasak, Z. Chara

Since the flow behaviour of slurry containing both coarse and very fine particles has not been sufficiently clarified, the paper focuses on the experimental study of the particle size distribution, time and intensity of shearing and the effect of chemical agents on the hydraulic gradient versus the average velocity relationship of fluidic ash slurries in the laminar and turbulent regimes. The recirculation pipe loop with smooth stainless steel pipes of inner diameters 26.8 and 36 mm was used for measuring the ash-water mixtures flow parameters. The dense fluidic ash-water mixtures behave as time dependent non-Newtonian slurries. Shearing, the addition of bottom ash or chemical agents, favourably affects the flow behaviour of dense fluidic ash-water slurries. The hydraulic gradient in the laminar region significantly decreases; also the laminar/turbulent transition region is reached for lower flow velocity.

Jan 1, 2007

Sedimentary Ores-Ancient and Modern (Revised), edited by C. H. James. Proceedings of the 15th Inter-University Geological Congress. University of Leicester, December, 1967. Special Publication No.1, Department of Geology, University of Leicester, February, 1969. Obtainable from: Leicester University Bookshop, May's Walk, Leicester LE 17 RD. Price: 42s. Postage and packing, 3s. 6d. This volume should be of interest to economic geologists and students in this field. A number of illustrated papers on the genesis of ores in sediments are presented; the authors include experts such as Prof G. C. Amstutz, Dr K. C. Dunham, Prof D. Williams and W. G. GarIick. The papers deal mainly with sulphide deposits, but the late Prof J. H. Taylor's contribution concerns ores of iron and manganese. Brief references to the Witwatersrand ores represent the only discussion of South African deposits. With the notable exception of W. G. Garlick's paper on Zambian copper deposits, the Abstracts given are inadequate, necessitating thorough reading of the papers to extract the important matter.

By C. S. Oteo, H. Suárez, P. de la Fuente

ABSTRACT: In the south of the Island of Gran Canaria (Spain) there appear layers of swelling clays inside volcanic formations of a fonolitic type, down to depths as low as 500 m, with thicknesses of 1 to 3 m. Two tunnels (each of length 1,500 m) have been built in these zones (ignimbrites and swelling clays), work on which started in the ‘70s. The construction has been influenced by phenomena of expansivity and decompression. Presented below are the problems that arose, the field and indoor studies conducted and the numerical optimisation of the lining. ZUSAMMENFASSUNG: Im Süden der Insel Gran Canaria (Spanien) kommen im Inneren vulkanischer Formationen phonolithischen Typs in Tiefen von bis zu 500 Metern 1 bis 3 Meter dicke Blähtonschichten vor. In diesem Gelände aus Schmelztuff und Blähton begann man zu Beginn der siebziger Jahre, zwei Tunnel von jeweils 1.500 Metern Länge anzulegen. Die Bauarbeiten standen unter dem Einfluss von Dehnungs- und Dekompressionserscheinungen. Der folgende Text enthält eine Darstellung der aufgetretenen Probleme, der durchgeführten Feld- und Laborstudien und der numerischen Optimierung der Tunnelauskleidung. RESUME: Dans le sud de l’Ille du Gran Canaria (Espagne) on a détecté des couches d’argile gonflante dans l’intérieur des formations de roches volcaniques fonolitiques, à la profondeur autom des 500 m, avec épaisseur de 1 à 3 m. On a perforé deux tunnels (de longueur 1.500 m chaque un) dans cettes zones (igniumbrités et argiles gonflantes), chantier qui comenza pendant les 70’. La construction on a influencé pour des phénomènes d’expansivité et de décompression. Dans cette communication on présente les problèmes presentes, les études de chantier et théoriques realicés et l’optimisation numérique développé pour dimensionner le revêtement.

Jan 1, 2003

By J. Sehata, J. Tshilongo, I. Govender, S. Pikinini, T. L. Moodley, M. Raedani

In the face of dwindling Merensky ore reserves in the early 1990s, Mintek developed the MF2 flotation circuit to economically recover platinum group metals from the shallow upper group-2 chromitite reef. By aligning the primary and secondary grind to the platinum group metal liberation kinetics, excessive fine chromite generation was avoided, and thus one could consistently produce high-grade concentrates (>200 g/t platinum group metals) with low chrome content (<3% Cr2O₃), well within smelter tolerances. This, coupled with upper group- 2's low-cost open-pit mining, made it particularly attractive to investors and mining houses alike. As a result, deeper lying reefs like middle group and lower group with lower platinum group metals grades and complex mineralogy, were primarily mined only for chromite using density-based separation processes (like spirals), of which the waste tailings are best classified as secondary platinum group metals resources. Today, with global platinum group metal demand rising and high grade upper ground-2 reserves rapidly diminishing, the industry must revisit these middle group and lower group tailings. Mineralogical analysis reveals several challenges: Middle group tailings feature platinum group metals locked within silicate matrices, while lower group tailings contain fine chromitite fragments, and are hosted within non-floating laurite grains, each presenting liberation and gangue issues. Smelter constraints still demand concentrates below 3% Cr₂O₃, requiring solutions that consider both platinum group metals recovery and chrome entrainment. To develop a solution, two lower group chrome spiral tailings samples were obtained from a large chrome mine: Sample A (+425 μm – 106 μm) and Sample B (−106 μm). Initial assays showed Sample B contained higher platinum group metal grades but also higher Cr₂O₃. As such, different blends of flotation feeds were evaluated using ratios of 90:10 (C1) and 80:20 (C2) of Sample A to Sample B, targeting the coarse fraction's lower chrome content while recovering valuable platinum group metals from the fines. This work proposes a practical route for mining houses to unlock additional platinum group metal value from lower group ore spiral tailings. By optimising blending ratios and reagent suites, it is possible to meet smelter chrome and platinum group metal grade thresholds, whilst still obtaining economically viable PGM recoveries.

Mar 6, 2026

By K. G. Lomberg

The density used to covert volume to tons is critical in determining the real in-situ tonnage of Mineral Resources. However, the methods used to determine density and the use of different technical terms are seen to be inconsistent throughout the industry. Probably the best discussion addressing the determination of density was presented by Lipton (2001). This paper does not try to replicate this excellent work, but rather to review current industry practice and present a comparison of the approach to density in public reporting. Some of the technical terms used in reporting and the common methods applied are also discussed.

Sep 1, 2021

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

By C. van Buuren, R. F. Sandenbergh, P. J. Pieterse

Gold extraction from double refractory ores using conventional cyanidation has proved challenging due to the presence of carbon within the ore. Carbon particles may adsorb leached gold resulting in gold losses to tailings, i.e. preg-robbing the gold. Some of the preg-robbed gold may be recovered by the application of the HiTeCC process on CIL tailings. The process developed by Metso Outotec involves caustic conditioning of the tailings followed by high temperature desorption and simultaneous adsorption onto virgin activated carbon of the aurodicyanide. The aim of this paper was to develop a model for the HiTeCC process which could be used to support design and optimisation of the process, based on the adsorption characteristics of the preg-robbing and activated carbons. It was found that accurate experimental isotherms can be used to predict the behaviour of preg-robbing adsorbents. Comparing the sorption isotherms for preg-robbing ores and activated carbon indicated similar dependencies on temperature and ionic composition. Applying boundary layer diffusion models coupled with experimentally determined isotherms for preg-robbing ore and activated carbon, the HiTeCC process was successfully simulated at experimental and plant scale. Gold recovery of the HiTeCC process is most sensitive to the temperature of desorption and gold loading of the activated carbon, with increased temperature improving recovery. The gold loading of the activated carbon in the process should always be maintained lower than that of the normalised pregrobbing carbon gold loading to ensure favourable conditions for adsorption onto the activated carbon. Caustic conditioning stabilises adsorption and is therefore not necessary during the desorption stages of the process, but potentially improves recovery during adsorption. Keywords: Preg-robbing, refractory gold ores, HiTeCC, aurodicyanide

Jan 1, 2020

By D. Pienaar, C. O’Connor, B. McFadzean

Dithiophosphate (DTP) is classically used as a co-collector in sulphide mineral flotation, where xanthate-DTP mixtures have been shown to synergistically improve mineral flotation performance. Notwithstanding the improved recoveries observed, ethyl DTP does not appear to behave as a conventional collector, since it has been shown that it does not adsorb onto certain sulphide mineral surfaces. Recent investigations have nevertheless indicated that when ethyl DTP does not adsorb onto the sulphide mineral surface, the presence of a non-ionic frother can activate a synergistic increase in pulp phase mineral recovery, and bubble-particle attachment probability. A regular solution approach was used to determine the interactions between thiol collectors and non-ionic frothers at the air-water interface. Attractive interactions were observed between longer alkyl chain DTPs and frothers, whereas the activity of xanthates at the air-water interface were too weak to determine if an interaction was occurring. This is the first time that such interactions have been shown for the DTP-frother system and represents an important contribution to our understanding of the role of DTP reagents in the flotation process. Keywords: Collector-frother interaction, dithiophosphate, surfactant synergism

Jan 1, 2020

By Y. Makola, M. Kilumba, S. Mwaba, P. Ilunga, F. Banze, B. Nel, P. Kyoni, N. Mautsa, R. Nkomba, G. Ilu

Kamoto Copper Company is a copper cobalt mining company established in Lualaba Province of Democratic Republic of Congo under a Joint Venture between Glencore PLC and Gecamines (the state-owned mining company). Operations consist of underground and open pit mines, a concentrator producing sulfide concentrate and oxide ores milled slurry, and a hydrometallurgy plant producing copper cathode and cobalt hydroxides from concentrate and ores. The production capacity is 300 k/a of copper cathode and 35 kt/a of cobalt hydroxide. Since Q4 2020, the Luilu hydrometallurgy plant has experienced operational instabilities due to increase in proportion of dolomite in the ore mined and fed to the plant. This was diagnosed by the significant increase in calcium grade in ore and acid consumption, continuous foaming, and overflow of tanks with subsequent adverse impact on equipment availability due to corrosion caused by acidic spills, structure integrity, and safety concerns around the acidic slurry spills. Production was adversely impact due above equipment availability and often throughput restriction to mitigate the foaming and overflows. A high gangue-acid-consuming ore management programme was developed with the aim of mitigating these impacts. The programme included: (i) use of defoamer agent in leach to stop foaming and overflow, (ii) design of a mechanical solution to leach foaming and overflow, and (iii) froth flotation for copper and cobalt minerals separation from dolomite. Only option (i) is presented in this paper. Through laboratory testwork, pilot-plant testing, plant trial, and full plant implementation, Kamoto Copper successfully implemented a defoamer agent (Kemfoam X9980) dosing at leach, resulting in significant reduction in foaming and overflow of leach reactors and countercurrent decantation thickeners. The optimum defoamer dose rate obtained was 20 mg/L. Since then, the Luilu recovered its operational stability, the corrosion of critical equipment ceased, and availability improved as the acidic leach slurry spills ceased. The constraint on throughput due to leach foaming was addressed and the frequency of sliming events in the thickeners was significantly reduced as the foaming on the supernatant surface ceased, with subsequent significant reduction in interfacial crud in solvent extraction.

Jan 1, 2023

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023

By S. M. H. Ahmadi, K. Barani, F. Moradpouri, R. Ghaedrahmati

As exploration is time-consuming, costly, and risky, determination of the erosion surface of a metalliferous deposit before geophysical surveying and exploration drilling might be very helpful. Geochemical haloes can be used to determine whether the erosion surface is supra-ore or sub-ore and thus reduce the risk of exploration operations. The aim of this investigation is to determine the erosion surface of the North ROK porphyry deposit (NRPD) in northwestern British Columbia in Canada using linear productivity (LP), which is the content of an element defining the halo multiplied by the width of the halo. A total of 2045 soil samples from the B horizon were analysed using ICP-MS for 36 elements, including Cu, Mo, Pb, Zn, Au, As, Ag, Ni, Co, Fe, and Mn. The data-set was snalysed to obtain the statistical parameters and the elements Cu, Mo, Pb, and Zn were chosen to calculate the linear productivity and the total linear productivity. These four elements were modelled using probability plots to identify and separate subpopulations in terms of anomalous haloes and background, including the threshold values of each subpopulation. The results of the probability plot modelling and thresholds values were then used to map the distribution of each element in a GIS to calculate the linear productivity. The total linear productivity indicated that the erosion surface is supra-ore. Finally, a 3D orebody model of the Cu, Mo, Pb, and Zn distributions was constructed using borehole data and used to validate the results.

Feb 6, 2023

By A. G. Royle

The reasons for constructing a model of an orebody for which both the parent population and the sampling distribution are known are discussed and details of the model are given. A brief summary of Matheron&apos;s theory of regionalized variables is included, with particular reference to his kriging estimators and their variances. Using the model, a comparison is then made between these kriging estimators and other commonly-used estimators. These are compared to find the one with the minimum variance, and an analysis is included to investigate whether any of the estimators is biased. Also included is a comparison between theoretical and experimental variances for some of the estimators.

Jan 1, 2014

By R. Rubin, P. A. Laxen, G. S. M. Becker

An account is given of developments in the use of activated carbon for the recovery of gold from cyanide solutions. The carbon-In-pulp process employed at the Homestake Mine is described, and its various applications in South Africa and their effectiveness are discussed. Probable future work on the carbon-in-pulp process and other possible applications of carbon for the recovery of gold are outlined.

Jan 1, 1979

By G. Akdogan, P. Mutimutema, M. Tadie

The South African gold mining industry has a legacy of abundant tailings dams, which have attracted the attention of investors because of their potential as a cheaper secondary gold resource. In this we investigate study gold recovery from a refractory calcine tailings dam. Bulk mineralogy of the tailings silicates and iron oxides to be the most abundant phases. Scanning Electron Microscopy (SEM) showed gold to exist in submicrometre and micrometre sizes, as free gold, and associated with arsenic, sulphur, and silicates e.g. quartz and talc. Gold recovery by direct cyanidation was low at 17.3%. Mechanical (ultra fine grinding P80 -16μm) and chemical (alkaline, NaOH) pre-treatment and microwave roasting and microwave-assisted cyanide leaching were investigated to increase gold recoveries. Ultrafine grinding was the most effective, producing recoveries of 66.5%. NaOH pre-leaching of ultrafine milled material increased recovery to 71.5%. Alkaline pre-leaching overall increased recoveries for non-pretreated material, making this process the most preferred because it is less costly than ultrafine grinding. Microwave roasting and microwave-assisted leaching did not achieve higher recoveries than alkaline pre-treatment or fine grinding. The investigation highlights and confirms that chemical treatment with NaOH is a powerful tool for gold extraction from refractory tailings.

Oct 1, 2022

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By L. A. Cisternas, R. I. Jeldres, D. Calisaya

"Flotation of copper-molybdenum sulphide ores in seawater entails critical challenges such as selective recovery of molybdenite, effective pyrite depression, and reducing the lime addition required to reach highly alkaline conditions. It is essential that laboratory flotation tests aimed at solving these problems give reliable, reproducible results and indicate the correct approach for industrial operations. Rougher flotation of coppermolybdenum sulphide ores in seawater was investigated using two different cells: a modified Denver cell and a standard commercial cell. The effect of an organic reagent on the flotation performance was tested, and the fast/slow-floating model was used to describe the results. The modified Denver cell significantly improved the reproducibility of the flotation test results, due to technological enhancements such as the impeller being driven from below without a stator, which enables the whole froth surface to be scraped with a paddle at a constant depth and rate. Organic reagents are a promising alternative to inorganic reagents for depressing pyrite in seawater. However, further studies should be conducted to investigate their impact on molybdenite recovery, as well as to evaluate the possibility of depressing pyrite after molybdenite separation. The fast/slow-floating model was found to be appropriate for describing the flotation kinetics of the copper-molybdenum ores. The parameters are useful for comparing the performance at different conditions. IntroductionOwing to the increasing scarcity of fresh water, the use of seawater mining and mineral processing is becoming increasingly important (Cisternas and Moreno, 2014). Seawater can be desalinated by reverse osmosis, but this involves considerable costs, limiting it to the big mining companies (Akgul et al., 2008; Leidner et al., 2012; Ghaffour, Missimer, and Amy, 2013). Furthermore, desalination has environmental consequences (Lee, Arnot, and Mattia, 2011); for example, a desalination plant designed to process 2.5 m3/s requires an electrical energy supply of around 30 MJ/s. To supply this power demand, a thermoelectric plant burning bituminous/sub-bituminous coal mixtures at a thermal power generation efficiency of 35% might release around 1200– 1500 t of CO2 per day. Furthermore, the effluents from desalination plants are typically discharged into the sea, and their high temperature and ionic content inevitably modifies the marine environment, with unknown consequences. The direct use of seawater is, therefore, more attractive, but it also poses major challenges since seawater contains ions that adversely affect mineral recoveries. In particular, in the flotation of sulphide ores in seawater, the floatability of molybdenite is depressed (Castro, 2012; Laskowski, Castro, and Ramos, 2014)."

Jan 1, 2017

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By A. Cambitsis

We show that the prioritization of business improvement and performance management decisions may be significantly improved by taking into account the systemic effects of changes made in a single process area. To do so we build a model of a mining value chain, taking into account consequential downtime that arises from downstream and upstream starvation and choking effects of each activity. Introducing the concept of internal capacity, this approach yields insight into the relative importance of key metrics such as loading and hauling rates. We suggest that a holistic view of this type should be a core component of business improvement and performance management decisions. Keywords value driver trees, production constraints, throughput analysis, capacity analysis, TOC (Theory of Constraints), activity interdependencies, unit cost reduction.

Oct 1, 2013

Report M294 A mineralogical investigation of potential gold-sorbing minerals and shales, by c.T. Logan. Dec. 1986. 12 pp. Computer software The Fifth IFAC/IFIP Symposium on Software for Computer Control (SOCOCO 88) is to be held in J ohannesburg from 26th to 28th April, 1988. Tunneling 88 The Institution of Mining and Metalurgy, with the cooperation of the British Tunneling Society, the Institution of Mining Engineers, and the Transport and Road Research Laboratory, Department of Transport, is pleased to announce the fifth international symposium, Tunneling 88, which wil be held in London, England, from 18th to 21st April, 1988. Ion-exchange processes ION-EX &apos;87, an international conference and industrial exhibition on the industrial, analytical, and preparative applications of ion chromatography and ionexchange processes, wil be held in Wrexham (North Wales) from 13th to 16th April, 1987.

Jan 1, 1987

By E. Mokgwamme, T. Goff, M. Mvalelwa, P. Spratt, P. Bezuidenhout, P. Nkosi, H. Joubert, G. de Villiers

Sibanye-Stillwater recently completed a partial sidewall rebuild on Furnace 1 at its Marikana smelter complex. The project involved matte taphole maintenance, which required the removal and subsequent replacement of 18 composite copper-graphite coolers and a section of the lower refractory sidewall. These composite copper-graphite coolers are a newly developed cooling design by Tenova Pyromet, and this rebuild project provided valuable insight into the performance of the composite coolers. The novel composite cooler design was implemented to serve as a safeguard against localised wear and corrosion in the furnace sidewall, particularly at the slag-concentrate interface, where chloride-accelerated sulphidation has been identified as a dominant degradation mechanism affecting the copper cooling elements. The composite cooler design is unique in that all the exposed sides of the water-cooled copper elements are fully encapsulated in graphite, which protects the copper from corrosive sulphur- and chlorinebearing gases and condensates. This sidewall cooling system was designed to improve corrosion resistance, stabilise freeze lining formation, and extend the campaign life of the furnace sidewall. The partial sidewall rebuild was executed during a planned maintenance shutdown with the main objective of replacing the matte taphole lintel bricks. This paper serves as a case study that compares and evaluates the operational performance of the composite coolers before and after the rebuild. The installation method is discussed to highlight the approach taken to ensure a sound installation while minimising downtime, as well as to present some lessons learned in the process.

Mar 6, 2026